Ricoh MP C2004/C2504 Service Manual Part 34

J

John

Member
5804[OUTPUT Check]
5-804-202Scanner LampENG[0 or 1 / 0 / 1/step]
Checks output of scanner lamp.
Use to check light source malfunction when SC101-01, SC101-02, SC102-00, SC142-00 occurs.
5-804-206PTR Open/Close LEDENG[0 or 1 / 0 / 1/step]
Lights paper transfer open/close LED.
5-804-208TM/P Sensor: FENG[0 or 1 / 0 / 1/step]
Lights TM/P sensor: Front glowing part.
5-804-209TM/P Sensor: CENG[0 or 1 / 0 / 1/step]
Lights TM/P sensor: Center glowing part.
5-804-210TM/P Sensor: RENG[0 or 1 / 0 / 1/step]
Lights TM/P sensor: Rear glowing part.
5-804-211Toner Sensor PowerENG[0 or 1 / 0 / 1/step]
5-804-232Toner IDTAG PowerENG[0 or 1 / 0 / 1/step]
5804[OUTPUT Check]
5-804-239Fusing Exit Drive SolenoidENG[0 or 1 / 0 / 1/step]
5804[OUTPUT Check]
Continuously drives specified motor for operation test.
5-804-241Bank: Tray3: Feed Mt: Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-242Bank: Tray4: Feed Mt: Standard SpeedENG
5-804-243Bank: Tray5: Feed Mt: Standard SpeedENG
5-804-244Bank: Tray3: Transport Mt: Standard SpeedENG
5-804-245Bank: Tray4: Transport Mt: Standard SpeedENG
5-804-246Bank: Tray5: Transport Mt: Standard SpeedENG
5804[OUTPUT Check]
Drives specified motor for a certain period of time to test operation.
5-804-247Bank: Tray3: PU SolenoidENG[0 or 1 / 0 / 1/step]
5-804-248Bank: Tray4: PU SolenoidENG
5-804-249Bank: Tray5: PU SolenoidENG




Engine SP Mode Tables



ADF



6008[ADF OUTPUT Check]
Checks operation of the load of ADF.
6-008-003Feed Motor ForwardENG[0 or 1 / 0 / 1/step]
Rotates paper feed motor forward.
6-008-004Feed Motor ReverseENG[0 or 1 / 0 / 1/step]
Rotates paper feed motor backward.
6-008-005Relay Motor ForwardENG[0 or 1 / 0 / 1/step]
Rotates carry motor forward.
6-008-006Relay Motor ReverseENG[0 or 1 / 0 / 1/step]
Rotates carry motor backward.
6-008-011Inverter SolenoidENG[0 or 1 / 0 / 1/step]
Interval drives reverse solenoid.
6-008-012StampENG[0 or 1 / 0 / 1/step]
Interval drives DONE stamp.
6-008-013Fan MotorENG[0 or 1 / 0 / 1/step]
Interval drives FAN motor.
6-008-014Feed ClutchENG[0 or 1 / 0 / 1/step]
Interval drives paper feed clutch.
6-008-015Feed SolenoidENG[0 or 1 / 0 / 1/step]
Interval drives paper feed solenoid.




6012[1-Pass ADF OUTPUT Check]
For Single-Pass simultaneous duplex models only.
6-012-001Pick-Up Motor ForwardENG[0 or 1 / 0 / 1/step] 0:Off
1:On
Forwardly rotates ADF pick up motor.
6-012-003Feed Motor ForwardENG[0 or 1 / 0 / 1/step] 0:Off
1:On
Forwardly rotates ADF paper feed motor.
6-012-005Relay Motor ForwardENG[0 or 1 / 0 / 1/step] 0:Off
1:On
Forwardly rotates ADF paper carry motor.
6-012-009Exit Motor ForwardENG[0 or 1 / 0 / 1/step] 0:Off
1:On
Forwardly rotates ADF paper exit motor.
6-012-010Bottom Plate Motor For/RevENG[0 or 1 / 0 / 1/step] 0:Off
1:On
Moves up/down the bottom plate by driving the ADF bottom plate motor forward, backward.
6-012-012StampENG[0 or 1 / 0 / 1/step] 0:Off
1:On
Stamps the DONE stamp.
6-012-015Pull-Out Motor ForwardENG[0 or 1 / 0 / 1/step] 0:Off
1:On
Forwardly rotates ADF pull out motor.
6-012-016Middle Motor ForwardENG[0 or 1 / 0 / 1/step] 0:Off
1:On
Forwardly rotates ADF middle motor.




Engine SP Mode Tables



Finisher



6124[OUTPUT Check: 2K/3K FIN]
6-124-001Entrance Transport MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-002Horizontal Transport MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-003Pre-Stack Transport MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-004ITB Transport MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-005Paper Exit MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-006Upper Junction SolenoidENG[0 or 1 / 0 / 1/step]
Turns NO/OFF specified solenoid for validation.
6-124-007TE Stack Plate MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-008Paper Exit Open/Close Guide Plate MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-009Punching MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-010Punch Move MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-011S-to-S Registration Detection Move MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-012Lower Junction Solenoid MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-013Jogger MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-014Positioning Roller Rotation MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-015Feed-out MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-016Booklet Stapler Move MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-017Corner Stapler MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-018Booklet Stapler Jogger MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-019Booklet Stapler Jog Solenoid Move MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-020Booklet Stapler Standard Fence MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-021Booklet Stapler MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-022Dynamic Roller Transport MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-023Folder Transport MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-025Press-fold MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-026Tray Lift MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-027Shift MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-028Front Shift Jogger MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
* Not use: currently, VOLGA-B does not have setting jogger in system configuration.
Engine SP Mode Tables





6-124-029Rear Shift Jogger MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
* Not use: currently, VOLGA-B does not have setting jogger in system configuration.
6-124-030Shift Jogger Retraction MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
* Not use: currently, VOLGA-B does not have setting jogger in system configuration.
6-124-031Drag Roller Vibrating MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-032LE Guide MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-033Navigation LED (All)ENG[0 or 1 / 0 / 1/step]
Lights all guide LED.
6-124-037Positioning Roller Transport MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-038Paper Guide MotorENG[0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.




6136[OUTPUT Check: FrontFIN]
Continuously drives specified motor for operation test.
6-136-001Entrance Motor*ENG[0 or 1 / 0 / 1/step]
6-136-002Carry MotorENG[0 or 1 / 0 / 1/step]
6-136-003Exit MotorENG[0 or 1 / 0 / 1/step]
6136[OUTPUT Check: FrontFIN]
Drives specified motor for a certain period of time to test operation.
6-136-004Front Jogger MotorENG[0 or 1 / 0 / 1/step]
6-136-005Rear Jogger MotorENG[0 or 1 / 0 / 1/step]
6-136-006Shift MotorENG[0 or 1 / 0 / 1/step]
6-136-007Hitroll MotorENG[0 or 1 / 0 / 1/step]
6-136-008Exit Guide Plate MotorENG[0 or 1 / 0 / 1/step]
6-136-009Staple Moving MotorENG[0 or 1 / 0 / 1/step]
6-136-010Tray MotorENG[0 or 1 / 0 / 1/step]
6-136-011Staple MotorENG[0 or 1 / 0 / 1/step]
6-136-012Stopper MotorENG[0 or 1 / 0 / 1/step]
6-136-013Punch MotorENG[0 or 1 / 0 / 1/step]
6-136-014Punch Moving MotorENG[0 or 1 / 0 / 1/step]
6-136-015Punch Registration Moving MotorENG[0 or 1 / 0 / 1/step]
Engine SP Mode Tables









6162[FIN (1K FIN) OUTPUT Check]
Continuously runs specified motor for operation test.
6-162-001Entrance Transport MotorENG[0 or 1 / 0 / 1/step]
6-162-002Proof Transport MotorENG[0 or 1 / 0 / 1/step]
6-162-003Paper Feed/Positioning & Move Roller MotorENG[0 or 1 / 0 / 1/step]
6162[FIN (1K FIN) OUTPUT Check]
Drives specified motor for a certain period of time to test operation.
6-162-004Junction SolenoidENG[0 or 1 / 0 / 1/step]
6-162-005Shift MotorENG[0 or 1 / 0 / 1/step]
6-162-006Jogger MotorENG[0 or 1 / 0 / 1/step]
6-162-007Exit Guide Plate Open/Close MotorENG[0 or 1 / 0 / 1/step]
6-162-008Feed-out MotorENG[0 or 1 / 0 / 1/step]
6-162-009Tray Lift MotorENG[0 or 1 / 0 / 1/step]
6-162-011Positioning Roller MotorENG[0 or 1 / 0 / 1/step]
6-162-012Stapler Shift MotorENG[0 or 1 / 0 / 1/step]
6-162-013Stapler MotorENG[0 or 1 / 0 / 1/step]
6-162-014UntitledENG[0 or 1 / 0 / 1/step]
6-162-015UntitledENG[0 or 1 / 0 / 1/step]
6-162-016UntitledENG[0 or 1 / 0 / 1/step]
6-162-017Punch MotorENG[0 or 1 / 0 / 1/step]
6-162-018Punch Move MotorENG[0 or 1 / 0 / 1/step]
6-162-019S-to-S Registration Detection Move MotorENG[0 or 1 / 0 / 1/step]
6-162-020Stack Transport Motor: UpperENG[0 or 1 / 0 / 1/step]
6-162-021Stck Trns Uppr Prss Rls/Stndrd Fence Rtrct MENG[0 or 1 / 0 / 1/step]
6-162-022Stack Lower Pressure Release MotorENG[0 or 1 / 0 / 1/step]
6162[FIN (1K FIN) OUTPUT Check]
Continuously runs specified motor for operation test.
6-162-023Folder Transport MotorENG[0 or 1 / 0 / 1/step]
6162[FIN (1K FIN) OUTPUT Check]
Drives specified motor for a certain period of time to test operation.
6-162-024TE Stopper MotorENG[0 or 1 / 0 / 1/step]
6-162-025Folder Blade MotorENG[0 or 1 / 0 / 1/step]
6162[FIN (1K FIN) OUTPUT Check]
Lights all guide LED.
6-162-026Navigation LED (All)ENG[0 or 1 / 0 / 1/step]
Engine SP Mode Tables









6185[Output Check: NoStplBindFIN]
6-185-001Transport MotorENG[0 or 1 / 0 / 1/step]
Checks the transport motor’s movement of non staple finisher.
6-185-002Shift MotorENG[0 or 1 / 0 / 1/step]
Checks the shift motor’s movement of non staple finisher.
6-185-003Junction Solenoid MotorENG[0 or 1 / 0 / 1/step]
Checks the junction solenoid motor’s movement of non staple finisher.
6-185-004Exit Pressure Release MotorENG[0 or 1 / 0 / 1/step]
Checks the exit pressure release motor’s movement of non staple finisher.
6-185-005Stapler MotorENG[0 or 1 / 0 / 1/step]
Checks the stapler motor’s movement of non staple finisher.

    1. TEST PATTERN PRINTING​


      Printing Test pattern: SP2-109
      Some of these test patterns are used for copy image adjustments but most are used primarily for design testing.
      • Do not operate the machine until the test pattern is printed out completely. Otherwise, SC will occur.
  2. Enter the SP mode then select SP2-109-003.
  3. Select test pattern for print from the list then press [OK].
  4. When selecting color for Printing; Full Color or either CMYK, go to SP2-109-005 (1: Full Color, 2: Cyan, 3: Magenta, 4: Yellow, 5: Black) to select.
  5. When changing density of test pattern, select density with SP2-109-006 through 009 for each color.
    • If select "0" with SP2-109-006 through 009, the color adjusted so will not show up in the test pattern.
  6. To Print, Touch "Copy Window", then set settings within the following window for test print (paper size etc…).
    • When using black and white printing, touch "Black & White" on the LCD. When using color printing, touch "Full Color" on the LCD.
  7. Press "Start" key to start test print.
  8. After checking test pattern, touch "SP Mode" on the LCD to return to SP mode display.
  9. Reset all settings to default values.
  10. Exit SP mode.


No.PatternNo.Pattern
0Copy image12Independent Pattern (2dot)
1Vertical Line (1dot)13Independent Pattern (4dot)
2Vertical Line (2dot)14Trimming Area
3Horizontal Line (1dot)15Hound's Tooth Check (Vertical)
4Horizontal Line (2dot)16Hound's Tooth Check (Horizontal)
5Grid Vertical Line17Band (Horizontal)
No.PatternNo.Pattern
6Grid Horizontal Line18Band (Vertical)
7Grid Pattern Small19Checker Flag Pattern
8Grid Pattern Large20Grayscale (Vertical Margin)
9Argyle Pattern Small21Grayscale (Horizontal Margin)
10Argyle Pattern Large22Wormy Pattern
11Independent Pattern (1dot)23Full Dot Pattern
Engine SP Mode Tables







RE V IS ION H IST ORY
PageDateAdded/ Updated/ New
None


APPENDIX: CONTROLLER SP MODE TABLES​





Controller SP Mode Tables



4. CONTROLLER SP MODE TABLES​



4.1 CONTROLLER SP TABLES - SP5000​



5024



4.1.1 SP5-XXX (MODE)​



5009[Add Display Language]
Adds language available in user choice. (Only the languages registered in the machine)
Refer to the displayed language list to set in the way showed below. List Number Assigned Bit Switch
No.1 to 8 BIT1 to 8 (SP5-009-201) No.9 to 16 BIT1 to 8 (SP5-009-202) No.17 to 24 BIT1 to 8 (SP5-009-203) No.25 to 32 BIT1 to 8 (SP5-009-204) No.33 to 40 BIT1 to 8 (SP5-009-205) No.41 to 48 BIT1 to 8 (SP5-009-206) No.49 to 56 BIT1 to 8 (SP5-009-207)
Example: To add American(No.3 in the list) or Czech (No.15) Turn Bit 3 of “SP5-009-201” 0 to 1 for American.
Turn Bit 7 of “SP5-009-202” 0 to 1 for Czech.
After setting, turn the main power switch off and on to make the setting valid.
5-009-2011-8*CTL[1 to 255 / 0 / 1]
5-009-2029-16*CTL[1 to 255 / 0 / 1]
5-009-20317-24*CTL[1 to 255 / 0 / 1]
5-009-20425-32*CTL[1 to 255 / 0 / 1]
5-009-20533-40*CTL[1 to 255 / 0 / 1]
5-009-20641-48*CTL[1 to 255 / 0 / 1]
5-009-20749-56*CTL[1 to 255 / 0 / 1]




[mm/inch Display Selection]



Display units (mm or inch) for custom paper sizes.
5-024-0010:mm 1:inch*CTL[0 or 1 / 1(USA), 0(Others) / 1]
0: mm
1: inch




5045[Accounting counter]
5-045-001Counter Method*CTL[0 to 7 / 1 / step]
0: Developments
1: Prints
2: Coverage
7: Coverage (YMC)




5047[Paper Display]
5-047-001Backing Paper*CTL[0 or 1 / 0 / 1]
0: OFF
1: ON




5051[TonerRefillDetectionDisplay]
5-051-001-*CTL[0 or 1 / 0 / 1]
0: ON
1: OFF




5055[Display IP Address]
5-055-001-*CTL[0 or 1 / 0 / 1]
0: OFF
1: ON




5061[Toner Remaining Icon Display Change]
5-061-001-*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5062[Parts Replacement Alert Display]
5-062-002#Photoconductor Unit (Black)*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-003#Development unit: Bk*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-025#Photoconductor Unit (Cyan)*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-026#Development unit: C*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-048#Photoconductor Unit (Magenta)*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-049#Development unit: M*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-071#Photoconductor Unit (Yellow)*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-072#Development unit: Y*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-093#Intermediate Transfer Unit*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-102#ITB Cleaning Unit*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
Controller SP Mode Tables





5-062-109#Paper Transfer Unit*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-115#Fuser Unit*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-116Fuser Unit: Belt*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-118Fuser Unit: Pressure Roller*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-131#Dust Filter*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-142#Wast Toner bottle*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-206#ADF Pick-up Roller*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-207#ADF Paper Supply Belt*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-208#ADF Separate Roller*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display




5066[PM Parts Display]
5-066-001-*CTL[0 or 1 / 0 / 1]
0: Not display
1: Display
5067[Part Replacement Operation Type]
5-067-002#Photoconductor Unit (Black)*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-003#Development unit: Bk*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-025#Photoconductor Unit (Cyan)*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-026#Development unit: C*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-048#Photoconductor Unit (Magenta)*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-049#Development unit: M*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-071#Photoconductor Unit (Yellow)*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-072#Development unit: Y*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-093#Intermediate Transfer Unit*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-102#ITB Cleaning Unit*CTL[0 or 1 / 0 / 1]
0: Service
1: User
Controller SP Mode Tables





5-067-109#Paper Transfer Unit*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-115#Fuser Unit*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-116Fuser Unit: Belt*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-118Fuser Unit: Pressure Roller*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-131#Dust Filter*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-142#Wast Toner bottle*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-206#ADF Pick-up Roller*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-207#ADF Paper Supply Belt*CTL[0 or 1 / 0 / 1]
0: Service
1: User
5-067-208#ADF Separate Roller*CTL[0 or 1 / 0 / 1]
0: Service
1: User




5071[Set Bypass Paper Size Display]
5-071-001-CTL[0 or 1 / 0 / 1]
0: Off
1: On
5073[Supply Part Replacement Opration Type]
5-073-001Waste Tonner Bottle*CTL[0 or 1 / 0 / 1] 0:No Display 1:Display
Controller SP Mode Tables









5074[Home Screen Login]
5-074-002Login Setting*CTL[0 to 255 / 0 / 1]
5-074-050Show Home Edit Menu*CTL[0 to 2 / 0 / 1]
5-074-091Function Setting*CTL[0 to 2 / 0 / 1]
0: Function disable
1: SDK application
2: Legacy application (reserved)
5-074-092Product ID*CTL[0x00 to 0xffff / - / 1]
5-074-093Application Screen ID*CTL[0 to 255 / 0 / 1]




5075[USB Keyboard]
5-075-003Display setting*CTL[0 or 1 / 0 / 1]
0: Disable
1: Enable




5081[ServiceSP Entery Code Setting]
DFU
5-081-001ServiceSP Entery Code Setting--




5083[LED Light Switch Setting]
5-083-001Toner Near End*CTL[0 or 1 / 0 / 1]
0: OFF
1: ON
5-083-002Waste Toner Near End*CTL[0 or 1 / 0 / 1]
5102[AutoDetect]
5-102-203HumanDetectSetting*CTL[0 or 1 / 0 / 1]




5114[Optional Counter I/F]
5-114-001MF Key Card Extension*CTL[0 or 1 / 0 / 1]
0: Not installed
1: Installed (scanning accounting)




5118[Disable Copying]
5-118-001-*CTL[0 or 1 / 0 / 1]
0: Not disabled
1: Disabled




5120[Mode Clear Opt. Counter Removal]
5-120-0010:Yes 1:StandBy 2:No*CTL[0 to 2 / 0 / 1]
0: Yes (removed)
1: Standby (installed but not used) 2: No (not removed)




5121[Counter Up Timing]
5-121-0010:Feed 1:Exit*CTL[0 or 1 / 0 / 1]
0: Feed
1: Exit




5127[APS Mode]
5-127-001-*CTL[0 or 1 / 0 / 1]
0: Not disabled
1: Disabled




5148[Size Detection Off]
5-148-002Tray 1*CTL[0 or 1 / 0 / 1]
5150[Length Setting]
5-150-001Bypass(0:OFF 1:Long)CTL[0 or 1 / 0 / 1]
0: OFF
1: ON
5193



Controller SP Mode Tables









5162[App. Switch Method]
5-162-001-*CTL[0 or 1 / 0 / 1] 0: Soft Key Set
1: Hard Key Set




5167[Fax Printing Mode at Optional Counter Off]
5-167-001-*CTL[0 or 1 / 0 / 1]
0: Automatic printing
1: No automatic printing




5169[CE Login]
5-169-001*CTL[0 or 1 / 0 / 1]
0: Disabled
1: Enabled




5188[Copy Nv Version]
5-188-001-*CTL[- / - / -]




5191[Mode Set]
5-191-001Power Str Set*CTL[0 or 1 / 1 / 1]
0: OFF
1: ON




[External Controller Info. Settings]



5-193-001-CTL[0 to 10 / 0 / 1]
0: External Controller is not installed
1: EFI
2: Ratio
3: Egret
4: GJ
5:Creo
6: QX-100
7: Kurofune
8 to 10: Reserved




5195[Limitless SW]
5-195-001-*CTL[0 or 1 / 0 / 1]
0: Productivity Precede 1: Use paper up




5196[Copier Vendor Mode]
5-196-00190 deg. RotationCTL[0 or 1 / 0 / 1]
5-196-002Color and Tray SelectionCTL[0 or 1 / 0 / 1]




5199[Paper Exit After Staple End]
5-199-001Staple(1:Without 2:After 0:Auto)CTL[0 to 2 / 0 / 1]
5-199-002Saddle(1:Without 2:After 0:Auto)CTL[0 to 2 / 0 / 1]
5-199-003Stapless(1:Without 2:After 0:Auto)CTL[0 to 2 / 0 / 1]




5212[Page Numbering]
5-212-003Duplex Printout Left/Right Position of Left/Right Facing*CTL[-10 to 10 / 0 / 0.01mm/step]
5-212-004Duplex Printout Top/Bottom Position of Left/Right Facing*CTL[-10 to 10 / 0 / 0.01mm/step]
5-212-018Duplex Printout Left/Right Position of Top/Bottom Facing*CTL[-10 to 10 / 0 / 0.01mm/step]
5-212-019Duplex Printout Top/Bottom Position of Top/Bottom Facing*CTL[-10 to 10 / 0 / 0.01mm/step]
Controller SP Mode Tables









5227[Page numbering]
5-227-201Allow Page No. Entry*CTL[2 to 9 / 9 / 1]
5-227-202Zero Surplus Stting*CTL[0 or 1 / 0 / 1] 0:OFF
1:ON




5302[Set Time]
Adjusts the RTC (real time clock) time setting for the local time zone. Examples: For Japan (+9 GMT), enter 540 (9 hours x 60 min.)
DOM: +540 (Tokyo)
NA: -300 (New York) EU: + 60 (Paris) CH: +480 (Beijing)
TW: +480 (Taipei)
AS: +480 (Hong Kong)
5-302-002Time Difference*CTL[-1440 to 1440 / - / 1min/step]




5305[Auto Off Set]
5-305-101Auto Off Limit Set*CTL[0 or 1 / 1 / 1]




5307[Daylight Saving Time]
5-307-001Setting*CTL[0 to 1 / - / 1]
0: Disabled
1: Enabled (Default)
1: NA and EUR
0: ASIA and others
Enables or disables the summer time mode.


  • Make sure that both SP5-307-3 and -4 are correctly set. Otherwise, this SP is not activated even if this SP is set to "1".
5-307-003Rule Set (Start)*CTL[0 to 0xffffffff / - / 1hex] (Default)
NA: 0x11100200 EUR: 0x10500100 ASIA: 0x03100000
Other: 0x00000000
Specifies the start setting for the summer time mode.
There are 8 digits in this SP. For months 1 to 9, the "0" cannot be input in the first digit, so the eight-digit setting for -2 or -3 becomes a seven-digit setting.
1st and 2nd digits: The month. [1 to 12] 3rd digit: The week of the month. [1 to 5]
4th digit: The day of the week. [0 to 6 = Sunday to Saturday] 5th and 6th digits: The hour. [00 to 23]
7th digit: The length of the advanced time. [0 to 9 / 1 hour ] 8th digit: The length of the advanced time. [0 to 5 / 10 minutes ]
  • The digits are counted from the left.
  • Make sure that SP5-307-1 is set to "1".
5-307-004Rule Set (End)*CTL[0 to 0xffffffff / - / 1hex]
Controller SP Mode Tables







Specifies the end setting for the summer time mode. There are 8 digits in this SP.

1st and 2nd digits: The month. [1 to 12] 3rd digit: The week of the month. [0 to 5]

4th digit: The day of the week. [0 to 7 = Sunday to Saturday] 5th and 6th digits: The hour. [00 to 23]

The 7th and 8 digits must be set to "00".

  • The digits are counted from the left.
  • Make sure that SP5-307-1 is set to "1".




5401[Access Control]
5-401-103Default Document ACLCTL[0 to 3 / 0 / 1]
5-401-104Authentication TimeCTL[0 to 255 / 0 / 1sec/step]
5-401-162Extend Certification DetailCTL[0 to 0xff / 0 / 1]
5-401-200SDK1 UniqueIDCTL[0 to 0xFFFFFFFF / 0 / 1]
5-401-201SDK1 Certification MethodCTL[0 to 0xFF / 0 / 1]
5-401-210SDK2 UniqueIDCTL[0 to 0xFFFFFFFF / 0 / 1]
5-401-211SDK2 Certification MethodCTL[0 to 0xFF / 0 / 1]
5-401-220SDK3 UniqueIDCTL[0 to 0xFFFFFFFF / 0 / 1]
5-401-221SDK3 Certification MethodCTL[0 to 0xFF / 0 / 1]
5-401-230SDK Certification Device*CTL[0 to 7 / 0 / power of 2]
0-1: SDK authentication available 0-0: Disable all functions
1-1: SKB Display
1-0: Disable
2-1: Administrator login
2-0: Disable
3 to 7-0: Reserved (set “0” only)
5-401-240Detail Option*CTL[0 to 7 / 0x00 / 0x01]


0: Logout confirm option

-1: ON, 0: OFF

2 to 1: Auto-logout timer(retry timer)

-11: 30sec, 10: 20sec, 01: 10sec, 00: 60sec

3: personal authority / Group authority and operation

-1: ON, 0: OFF

4: Skip password entry

-1: ON, 0: OFF

5: Set the display of the remaining Frequence

-1: ON, 0: OFF

6 to 7: Set the display time

-1: ON, 0: OFF





5402[Access Control]
5-402-101SDKJ1 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-102SDKJ2 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-103SDKJ3 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-104SDKJ4 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-105SDKJ5 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-106SDKJ6 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-107SDKJ7 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-108SDKJ8 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-109SDKJ9 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-110SDKJ10 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-111SDKJ11 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-112SDKJ12 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-113SDKJ13 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-114SDKJ14 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-115SDKJ15 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-116SDKJ16 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-117SDKJ17 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-118SDKJ18 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-119SDKJ19 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-120SDKJ20 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-121SDKJ21 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-122SDKJ22 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-123SDKJ23 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-124SDKJ24 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-125SDKJ25 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-126SDKJ26 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-127SDKJ27 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-128SDKJ28 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-129SDKJ29 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-130SDKJ30 Limit SettingCTL[0 to 0xff / 0 / 1]
5-402-141SDKJ1 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-142SDKJ2 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-143SDKJ3 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-144SDKJ4 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-145SDKJ5 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-146SDKJ6 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-147SDKJ7 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-148SDKJ8 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-149SDKJ9 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-150SDKJ10 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-151SDKJ11 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-152SDKJ12 ProductIDCTL[0 to 0xffffffff / 0 / 1]
Controller SP Mode Tables





5-402-153SDKJ13 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-154SDKJ14 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-155SDKJ15 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-156SDKJ16 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-157SDKJ17 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-158SDKJ18 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-159SDKJ19 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-160SDKJ20 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-161SDKJ21 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-162SDKJ22 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-163SDKJ23 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-164SDKJ24 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-165SDKJ25 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-166SDKJ26 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-167SDKJ27 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-168SDKJ28 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-169SDKJ29 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5-402-170SDKJ30 ProductIDCTL[0 to 0xffffffff / 0 / 1]
5411







5404[User Code Count Clear]
5-404-001User Code Count Clear*CTL[- / - / -]
[Execute]
5-404-101User Code Count Clear Permit Setting*CTL[0 or 1 / 0 / 1]




[LDAP-Certification]



5-411-004Easy Certification*CTL[0 or 1 / 1 / 1]
1: On
0: Off
5-411-005Password Null Not Permit*CTL[0 or 1 / 0 / 1]
0: Password NULL not permitted. 1: Password NULL permitted.
5-411-006Detail Option*CTL[0 or 1 / 0 / 1]
0: OFF
1: ON
Controller SP Mode Tables









5412[Krb-Certification]
5-412-100Encrypt ModeCTL[0 to 0xFF / 0x1F / 1]




5413[Lockout Setting]
5-413-001Lockout On/Off*CTL[0 or 1 / 0 / 1]
0: Off
1: On
5-413-002Lockout Threshold*CTL[1 to 10 / 5 / 1]
5-413-003Cancellation On/Off*CTL[0 or 1 / 0 / 1]
0: Off (no wait time, lockout not cancelled)
1: On (system waits, cancels lockout if correct user ID and password are entered.
5-413-004Cancellation Time*CTL[1 to 9999 / 60 / 1min]




5414[Access Mitigation]
5-414-001Mitigation On/Off*CTL[0 or 1 / 0 / 1]
0: OFF
1: ON
5-414-002Mitigation Time*CTL[0 to 60 / 15 / 1min/step]
5415[Password Attack]
5-415-001Permissible Number*CTL[0 to 100 / 30 /1attempt/step]
5-415-002Detect Time*CTL[1 to 10 / 5 / 1sec/step]




5416[Access Information]
5-416-001Access User Max Num*CTL[50 to 200 / 200 / 1user/step]
5-416-002Access Password Max Num*CTL[50 to 200 / 200 / 1password/step]
5-416-003Monitor Interval*CTL[1 to 10 / 3 / 1sec/step]




5417[Access Attack]
5-417-001Access Permissible Number*CTL[0 to 500 / 100 / 1/step]
5-417-002Attack Detect Time*CTL[10 to 30 / 10 / 1sec/step]
5-417-003Productivity Fall Wait*CTL[0 to 9 / 3 / 1sec/step]
5-417-004Attack Max Num*CTL[50 to 200 / 200 / 1attempt/step]




5420[User Authentication]
5-420-001Copy*CTL[0 to 1 / 0 / 1]
0: On
1: Off
5-420-002Color Security Setting*CTL[0x00 to 0xFF / 0x00 / 1]
5-420-011DocumentServer*CTL[0 or 1/ 0 / 1]
0: On
1: Off
5-420-021Fax*CTL[0 or 1/ 0 / 1]
0: On
1: Off
5-420-031Scanner*CTL[0 or 1/ 0 / 1]
0: On
1: Off
5-420-041Printer*CTL[0 or 1/ 0 / 1]
0: On
1: Off
5-420-051SDK1*CTL[0 or 1 / 0 / 1]
0: ON
1: OFF
5-420-061SDK2*CTL
5-420-071SDK3*CTL
5-420-081Browser*CTL[0 or 1 / 0 / 1]
0: ON
1: OFF
Controller SP Mode Tables









5430[Auth Dialog Message Change]
5-430-001Message Change On/OffCTL[0 or 1 / 0 / 1]
5-430-002Message Text DownloadCTL[- / - / -]
5-430-003Message Text IDCTL[- / - / -]




5431[External Auth User Preset]
5-431-010TagCTL[0 or 1 / 1 / 1]
5-431-011EntryCTL[0 or 1 / 1 / 1]
5-431-012GroupCTL[0 or 1 / 1 / 1]
5-431-020MailCTL[0 or 1 / 1 / 1]
5-431-030FaxCTL[0 or 1 / 1 / 1]
5-431-031FaxSubCTL[0 or 1 / 1 / 1]
5-431-032FolderCTL[0 or 1 / 1 / 1]
5-431-033ProtectCodeCTL[0 or 1 / 1 / 1]
5-431-034SmtpAuthCTL[0 or 1 / 1 / 1]
5-431-035LdapAuthCTL[0 or 1 / 1 / 1]
5-431-036Smb Ftp Fldr AuthCTL[0 or 1 / 1 / 1]
5-431-037AcntAclCTL[0 or 1 / 1 / 1]
5-431-038DocumentAclCTL[0 or 1 / 1 / 1]
5-431-040CertCryptCTL[0 or 1 / 0 / 1]
5-431-050UserLimitCountCTL[0 or 1 / 1 / 1]
5504







5481[Authentication Error Code]
5-481-001System Log Disp*CTL[0 or 1 / 0 / 1]
0: Off
1: On
5-481-002Panel Disp*CTL[0 or 1 / 0 / 1]
1: On
0: Off




5490[MF KeyCard (Japan only)]
5-490-001Job Permit Setting*CTL[0 to 1 / 0 / 1]
0: Disabled. Cancels operation without a user code.
1: Enabled. Allows operation without a user code.
5-490-002Count Mode Setting*CTL-




5491[Optional Counter]
5-491-001Detail Option*CTL[0 to 0xff / 0 / 1]




5501[PM Alarm]
5-501-001PM Alarm Level*CTL[0 to 9999 / 0 / 1]
0: Alarm off
1 to 9999: Alarm goes off when Value (1 to 9999) x 1000 > PM counter




[Jam Alarm]



5-504-001-*CTL[0 to 3 / 3 / 1]
0: Z
1: L
2: M
3: H
5-504-002Threshold*CTL[1 to 99 / 10 / 1]
Controller SP Mode Tables









5505[Error Alarm]
5-505-001Error Alarm*CTL[0 to 255 / * / 1 x102 sheets/step]
0: Alarm Off
* C2503 :20 / C2003:15
5-505-002Threshold*CTL[1 to 99 / 5 / 1]




5507[Supply/CC Alarm]
5-507-001Paper Supply Alarm*CTL[0 or 1 / 0 / 1]
0: OFF
1: ON
5-507-002Staple Supply Alarm*CTL[0 or 1 / 0 / 1]
0: OFF
1: ON
5-507-003Toner Supply Alarm*CTL[0 or 1 / 0 / 1]
0: OFF
1: ON
5-507-006WasteTonerBottle*CTL[0 to 2 / 1 / 1] 0:OFF
1: Supply Call ON 2: CC Call ON
5-507-080Toner Call Timing*CTL[0 or 1 / 0 / 1]
0: Toner bottle replacement 1: Less than toner threshold
5-507-080Toner Call TimingCTL[0 or 1 / 0 / 1]
5-507-081Toner Call Threshold:BkCTL[10 to 90 / 10 / 10%/step]
5-507-082Toner Call Threshold:CMYCTL[10 to 90 / 10 / 10%/step]
5-507-128Interval :Others*CTL[250 to 10000 / 1000 /
1page/step]
5-507-132Interval :A3*CTL[250 to 10000 / 1000 /
1page/step]
5-507-133Interval :A4*CTL[250 to 10000 / 1000 /
1page/step]
5-507-134Interval :A5*CTL[250 to 10000 / 1000 /
1page/step]
5-507-141Interval :B4*CTL[250 to 10000 / 1000 /
1page/step]
5-507-142Interval :B5*CTL[250 to 10000 / 1000 /
1page/step]
5-507-160Interval :DLT*CTL[250 to 10000 / 1000 /
1page/step]
5-507-164Interval: LG*CTL[250 to 10000 / 1000 /
1page/step]
5-507-166Interval :LT*CTL[250 to 10000 / 1000 /
1page/step]
5-507-172Interval :HLT*CTL[250 to 10000 / 1000 /
1page/step]




5508[CC Call]
5-508-001Jam Remains*CTL[0 or 1 / 1 / 1]
0: Disable
1: Enable
5-508-002Continuous Jams*CTL[0 or 1 / 1 / 1]
0: Disable
1: Enable
5-508-003Continuous Door Open*CTL[0 or 1 / 1 / 1]
0: Disable
1: Enable
5-508-011Jam Detection: Time Length*CTL[3 to 30 / 10 / 1min/step]
5-508-012Jam Detection: Continuous Count*CTL[2 to 10 / 5 / 1time/step]
5-508-013Door Open: Time Length*CTL[3 to 30 / 10 / 1min/step]
Controller SP Mode Tables









5513[PartsAlermlevelCount]
5-513-001Normal*CTL[1 to 9999 / 300 / 1]
5-513-002Df*CTL[1 to 9999 / 300 / 1]




5514[PartsAlermlev]
5-514-001Normal*CTL[0 or 1 / 1 / 1]
5-514-002Df*CTL[0 or 1 / 0 / 1]




5515[SC/Alarm Setting]
5-515-001SC Call*CTL[0 or 1 / 1 / 1]
0: OFF
1: ON
5-515-002Service Parts Near End Call*CTL
5-515-003Service Parts End Call*CTL
5-515-004User Call*CTL
5-515-006Communication Test Call*CTL
5-515-007Machine Information Notice*CTL
5-515-008Alarm Notice*CTL
5-515-009Non Genuine Tonner Ararm*CTL
5-515-010Supply Automatic Ordering Call*CTL
5-515-011Supply Management Report Call*CTL
5-515-012Jam/Door Open Call*CTL
5-515-050Timeout:Manual Call*CTL[1 to 255 / 5 / 1min/step]
5-515-051Timeout:Other Call*CTL[1 to 255 / 10 / 1min/step]




5517[Get Machine Information]
5-517-031Get SMC Info: Retry Interval*CTL[10 to 255 / 10 / 1min/step]




5618[Color Mode Display Selection]
5-618-001-*CTL[0 or 1 / 1 / 1]
0: ACS, Color, Black & White, Two Colors, Single color
1: ACD, Full Color, Black & White




5728[Network Setting]
5-728-001NAT Machine Port1CTL[1 to 65535 / 49101 / 1]
5-728-002NAT UI Port1CTL[1 to 65535 / 55101 / 1]
5-728-003NAT Machine Port2CTL[1 to 65535 / 49102 / 1]
5-728-004NAT UI Port2CTL[1 to 65535 / 55102 / 1]
5-728-005NAT Machine Port3CTL[1 to 65535 / 49103 / 1]
5-728-006NAT UI Port3CTL[1 to 65535 / 55103 / 1]
5-728-007NAT Machine Port4CTL[1 to 65535 / 49104 / 1]
5-728-008NAT UI Port4CTL[1 to 65535 / 55104 / 1]
5-728-009NAT Machine Port5CTL[1 to 65535 / 49105 / 1]
5-728-010NAT UI Port5CTL[1 to 65535 / 55105 / 1]
5-728-011NAT Machine Port6CTL[1 to 65535 / 49106 / 1]
5-728-012NAT UI Port6CTL[1 to 65535 / 55106 / 1]
5-728-013NAT Machine Port7CTL[1 to 65535 / 49107 / 1]
5-728-014NAT UI Port7CTL[1 to 65535 / 55107 / 1]
5-728-015NAT Machine Port8CTL[1 to 65535 / 49108 / 1]
5-728-016NAT UI Port8CTL[1 to 65535 / 55108 / 1]
5-728-017NAT Machine Port9CTL[1 to 65535 / 49109 / 1]
5-728-018NAT UI Port9CTL[1 to 65535 / 55109 / 1]
5-728-019NAT Machine Port10CTL[1 to 65535 / 49110 / 1]
5-728-020NAT UI Port10CTL[1 to 65535 / 55110 / 1]
5741



Controller SP Mode Tables









5730[Extended Function Setting]
5-730-001JavaTM Platform setting*CTL[0 or 1 / 1 / -]
0: Disable, 1: Enable
5-730-010Expiration Prior Alarm Set*CTL[0 to 999 / 20 / 1day/step]




5731[Counter Effect]
This SP is used only for DOM machines.
5-731-001Change MK1 Cnt (Paper->Combine)*CTL[0 or 1 / 0 / 1]




5732[Reset Job After Jam(Copy)]
5-732-002*CTL[0 or 1 / 0 / 1]




5734[PDF Setting]
5-734-001PDF/A Fixed*CTL[0 or 1 / 0 / 1]




[Node Authentication Timuout]



5-741-001*CTL[1 to 255 / 60 / 1sec/step]




5745[DeemedPowerConsumption]
5-745-211Controller Standby*CTL[0 to 9999 / 0 / 1]
5-745-212STR*CTL[0 to 9999 / 0 / 1]
5-745-213Main Power Off*CTL[0 to 9999 / 0 / 1]
5-745-214Scanning and Printing*CTL[0 to 9999 / 0 / 1]
5-745-215Printing*CTL[0 to 9999 / 0 / 1]
5-745-216Scanning*CTL[0 to 9999 / 0 / 1]
5-745-217Engine Standby*CTL[0 to 9999 / 0 / 1]
5-745-218Low Power Consumption*CTL[0 to 9999 / 0 / 1]
5-745-219Silent condition*CTL[0 to 9999 / 0 / 1]
5-745-220Heater Off*CTL[0 to 9999 / 0 / 1]




5748[OpePanel Setting]
5-748-101Op Type Action SettingCTL[0x00 to 0xFF / 0 / 0x01]
  • bit0
0: Normal operation panel 1: Smart operation panel
5-748-201Cheetah Panel Connect SettingCTL[0 or 1 / 0 / 0]
0: OFF
1: ON




5749[Import/Export]
5-749-001ExportCTL[- / - / -]
Target: System, Printer, Fax, Scanner Option: Unique, Secret
Copy config: Encryption, Encryption key(if selected)
[Execute]
5-749-101ImportCTL[- / - / -]
Option: Unique
Copy config: Encryption, Encryption key(if selected)
[Execute]
Controller SP Mode Tables









5751[Key Event Encryption Setting]
5-751-001PasswordCTL[0 to 255 / 0 / 1]




5752[Copy:WebAPI Setting]
5-752-001Copy FlairAPI Setting*CTL* see BitSwitch below:

Bit
Setting		meanings
Description
01
bit 0Start of FlairAPI ServerOff (Do not Start)On (Start)Sets whether to start exclusive FlairAPI http server. If it is 0, scanning FlairAPI function and simple UI function will be disabled. The machine installed Android operating panel option, set “1”, others set “0”.
bit 1Access permission of FlairAPI from outside of the machineDisabledEnabledIf it is “0”, accessing is limited from the machine only, such as operating panel, SDK/J, MFP browsers etc... If it is “1”, accessing is allowed from outside of FlairAPI such as PC, Remote UI, IT-Box etc...
bit 2Reserved---
bit 3Reserved---
bit 4Simple UI FunctionDisabledEnabledIf it is “1”, the machine can be used Scanner Simple UI. If it is “0”, requesting URL of Simple UI returns “404 Not Found”
bit 5Accessing permission of Simple UI from outside of the machineDisabledEnabledIf it is “0”, accessing is limited from the machine only (operating panel and MFP browser). If it is “1”, accessing is allowed from outside of Simple UI such as PC, mobile devices, and so on.
bit 6Reserved---
bit 7Reserved---
5801







5755[Display Setting]
5-755-001Disp Administrator Password Change ScrnCTL[- / - / -]
5-755-002Hide Administrator Password Change ScrnCTL[- / - / -]




5758[RemoteUI Setting]
5-758-001Authentication*CTL[0 or 1 / 0 / 1]




5759[Machine Limit Count]
5-759-001Machine Limit Count Setting*CTL[0 or 1 / 0 / 1]
5-759-061Full Color Limit Count*CTL[0 to 99999999 / 0 / 1]
5-759-062Mono Color Limit Count*CTL[0 to 99999999 / 0 / 1]




[Memory Clear]



5-801-001All ClearCTL[- / - / -]
[Execute]
5-801-003SCSCTL[- / - / -]
[Execute]
5-801-004IMH Memory ClrCTL[- / - / -]
[Execute]
5-801-005McsCTL[- / - / -]
[Execute]
5-801-006Copier ApplicationCTL[- / - / -]
[Execute]
5-801-007Fax ApplicationCTL[- / - / -]
[Execute]
5-801-008Printer ApplicationCTL[- / - / -]
[Execute]
The following service settings:
  • Bit switches
  • Gamma settings (User & Service)
  • Toner Limit
  • Tray Priority
  • Menu Protect
  • System Setting except for setting of Energy Saver
  • I/F Setup (I/O Buffer and I/O Timeout)
  • PCL Menu
The following user settings:
5-801-009Scanner ApplicationCTL[- / - / -]
[Execute]
5-801-010Web ServiceCTL[- / - / -]
[Execute]
5-801-011NCSCTL[- / - / -]
[Execute]
5-801-012R-FaxCTL[- / - / -]
[Execute]
Controller SP Mode Tables





5-801-014Clear DCS SettingCTL[- / - / -]
[Execute]
5-801-015Clear UCS SettingCTL[- / - / -]
[Execute]
5-801-016MIRS Memory ClrCTL[- / - / -]
[Execute]
5-801-017CCSCTL[- / - / -]
[Execute]
5-801-018SRM Memory ClrCTL[- / - / -]
[Execute]
5-801-019LCS Memory ClrCTL[- / - / -]
[Execute]
5-801-020Web UapliCTL[- / - / -]
[Execute]
5-801-021ECSCTL[- / - / -]
[Execute]
5-801-023AICSCTL[- / - / -]
[Execute]
5-801-025WebsysCTL[- / - / -]
[Execute]
5-801-026PLNCTL[- / - / -]
[Execute]
5-801-027SASCTL[- / - / -]
[Execute]
5-801-028Rest WebServiceCTL[- / - / -]
[Execute]
5816[Remote Service]
5-816-001I/F Setting*CTL[0 to 2 / 2 / 1]
0: Remote service off
1: CSS remote service on 2: NRS remote service on
5-816-002CE Call*CTL[0 or 1 / 0 / 1]
0: Start of the service 1: End of the service
5-816-003Function Flag*CTL[0 or 1 / 0 / 1]
0: Disabled
1: Enabled
5-816-007SSL Disable*CTL[0 or 1 / 0 / 1]
0: Yes. SSL not used. 1: No. SSL used.
5-816-008RCG Connect Timeout*CTL[1 to 90 / 30 / 1second/step]
5-816-009RCG Write Timeout*CTL[0 to 100 / 60 / 1second/step]
5-816-010RCG Read Timeout*CTL[0 to 100 / 60 / 1second/step]
5-816-011Port 80 Enable*CTL[0 or 1 / 0 / 1]
0: No. Access denied 1: Yes. Access granted.
5-816-013RFU Timing*CTL[0 or 1 / 1 / 1]
0: Any status of a target machine 1: Sleep or panel off mode only
5-816-014RCG Error CauseCTL[0 or 1 / 0 / 1]
0: Initial state, normal condition 1: Error
5-816-021RCG – C Registed*CTL[0 or 1 / 0 / 1]
0: Installation not completed 1: Installation completed


5-812-003Supply*CTL[up to 20 / - / 1]
5-812-004Operation*CTL[up to 20 / - / 1]


Controller SP Mode Tables









5812[Service Tel. No. Setting]
5-812-001Service*CTL[up to 20 / - / 1]
5-812-002Facsimile*CTL[up to 20 / - / 1]
5-816-023connect type(N/M)*CTL[0 or 1 / 0 / 1]
0: internet connection
1: Dial-up connection
5-816-061Cert Expire Timing*CTL[0 to 0xffffffff / 0 / 1]
0: Not use
1: Use
5-816-062Use Proxy*CTL[0 or 1 / 0 / 1]
0: Not use
1: Use
5-816-063Proxy Host*CTL[- / - / -]
5-816-064Proxy PortNumber*CTL[0 to 0xffff / 0 / 1]
5-816-065Proxy User Name*CTL[up to 31 / - / 1]
5-816-066Proxy Password*CTL[up to 31 / - / 1]
5-816-067Proxy Password*CTL[0 to 255 / 0 / 1]
Displays status of the certification used for Cumin.
If it is not installed as Cumin, the value of this SP will be set when it installed, after checking the certification status.
0The certification adequately set on the machine.
1Request for certification update in progress.
2Certification Update completed and notification of the success status to the G/W in progress.
3Certification Update failed and notification of the result to the G/W in progress.
4Certification expiration date will be coming soon. Notifying the G/W to request for certification update.
11Rescue certification setting for connecting to the rescue G/W in progress because update for rescue certification needed.
12Setting for rescue certification has completed. Requesting to the rescue G/W for updating certification.
13Notification for certification updating request has completed. Waiting for the certification update request from the rescue G/W.
14Received the notification for certification updating request from the rescue G/W. Writing the certification.
15Writing the certification has completed. Notifying the result of certification update to the G/W.
16Writing the certification has failed. Notifying the result of certification update to the G/W.
17Writing a rescue certification because received a certification error again after completed the certification update request from the G/W and noticed the result of certification update with the updated certification.
18The writing operation mentioned in #17 has completed. Notifying the result of certification update to the rescue G/W.
5-816-068CERT: Error*CTL[0 to 255 / 0 / 1]
Displays a number code that describes the reason for the request for update of the certification.
0Normal. There is no request for certification update in progress.
1Request for certification update in progress. The current certification has expired.
2An SSL error notification has been issued. Issued after the certification has expired.
3Notification of shift from a common authentication to an individual certification.
4Notification of a common certification without ID2.
5Notification that no certification was issued.
6Notification that GW URL does not exist.
5-816-069CERT: Up ID*CTL[- / - / -]
-
Controller SP Mode Tables





5-816-083Firm Up Status*CTL[0 to 5 / 0 / 1]
0: Waiting for accepting firm update
1: Waiting for firm update start schedule
2: Waiting for user confirmation 3: In preparation for the machine firm update
4: processing the machine firm update
5: processing the closing operation of the machine firm update
5-816-085Firm Up User CheckCTL[- / - / -]
5-816-086Firmware SizeCTL[- / - / -]
5-816-087CERT:Macro Ver.CTL[8digits / - / 1digit/step]
5-816-088CERT:pAC Ver.CTL[16digits / - / 1digit/step]
5-816-089CERT:ID2CodeCTL[17digits / - / 1digit/step]
5-816-090CERT:SubjectCTL[17digits / - / 1digit/step]
5-816-091CERT:Serial No.CTL[16digits / - / 1digit/step]
5-816-092CERT:IssuerCTL[30digits / - / 1digit/step]
5-816-093CERT:Valid StartCTL[10digits / - / 1digit/step]
5-816-094CERT:Valid EndCTL[10digits / - / 1digit/step]
5-816-102CERT:Encrypt Level*CTL[1 to 2 / 1 / 1]
5-816-103Client Communication MethodCTL[0 to 3 / 0 / 1]
5-816-104Client Communication LimitCTL[1 to 7 / 7 / 1]
5-816-115Network Information Waiting timerCTL[5 to 255 / 5 / 1sec/step]
5-816-150Selection CountryCTL[0 to 10 / 1 / 1]
0: Japan
1: USA
2: Canada
3: UK
4: Germany
5: France
6: Italy
7: Netherlands
8: Belgium
9: Luxembourg
10: Spain
Select the country where embedded RCG-M is installed in the machine. After selecting the country, you must also set the following SP codes for embedded RCG-M:
  • SP5816-153
  • SP5816-154
  • SP5816-161
5-816-151Line Type AutomaticJudgmentCTL[- / - / -]
[Execute]
5-816-152Line Type Judgment ResultCTL[0 to 9 / - / 1]
Displays a number to show the result of the execution of SP5816 151. Here is a list of what the numbers mean.
0: Success
1: In progress (no result yet). Please wait. 2: Line abnormal
3: Cannot detect dial tone automatically 4: Line is disconnected
5: Insufficient electrical power supply 6: Line classification not supported
7: Error because fax transmission in progress – ioctl() occurred. 8: Other error occurred
9: Line classification still in progress. Please wait.
Controller SP Mode Tables
 

Similar threads

J
Ricoh MP C2004/C2504 Service Manual Part 33
Replies
0
Views
16
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 32
Replies
0
Views
52
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 31
Replies
0
Views
76
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 30
Replies
0
Views
52
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 29
Replies
0
Views
54
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 28
Replies
0
Views
60
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 27
Replies
0
Views
59
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 26
Replies
0
Views
57
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 25
Replies
0
Views
82
John
J
Top