Ricoh MP C2004/C2504 Service Manual Part 32

J

John

Member
4-611-001Book Scan*ENG[-384 to 255 / -100 / 1digit/step]
4-611-002DF Scan*ENG[-384 to 255 / -100 / 1digit/step]




4635[SSCG Correction Set]
4-635-001Mode Selection*ENG[0 to 3 / 1 / 1/step]
0: Do not noise correct SSCG.
1: Only adjust analog (initial value) 2: Only adjust digital
3: Adjust both analog/digital




4646[Scan Adjust Error]
4-646-001White levelENG[0 to 65535 / 0 / 1/step] Bit15:Unused
Bit14: Unused
Bit13:White level abnormal (F side/RED/EVEN pixel)
Bit12: White level abnormal (F side /RED/ODD pixel)
Bit11: White level abnormal (F side
/GREEN/EVEN pixel)
Bit10: White level abnormal (F side /GREEN/ODD pixel)
Bit9: White level abnormal (F side /BLUE/EVEN pixel)
Bit8:White level abnormal (F side /BLUE/ODD pixel)
Bit7: Unused Bit6: Unused
Bit5:gain abnormal (F side /RED/EVEN pixel) Bit4: gain abnormal (F side /RED/ODD pixel) Bit3: gain abnormal (F side /GREEN/EVEN pixel) Bit2: gain abnormal (F side /GREEN/ODD pixel) Bit1: gain abnormal (F side /BLUE/EVEN pixel) Bit0: gain abnormal (F side /BLUE/ODD pixel)
4-646-002Black levelENG[0 to 65535 / 0 / 1/step] Bit7: Unused
Bit6: Unused
Bit5: Black level abnormal (F side/RED/EVEN Pixel)
Bit4: Black level abnormal (F side /RED/ODD Pixel)
Bit3: Black level abnormal (F side /GREEN/EVEN Pixel)
Bit2: Black level abnormal (F side /GREEN/ODD Pixel)
Bit1: Black level abnormal (F side /BLUE/EVEN Pixel)
Bit0: Black level abnormal (F side /BLUE/ODD Pixel)
4-646-003SSCG
Correction		ENG[0 to 65535 / 0 / 1/step] Bit7: Unused
Bit6: Unused
Bit5: SSCG correction error (Fside/RED/EVEN Pixel)
Bit4: SSCG correction error (Fside/RED/ODD Pixel)
Bit3: SSCG correction error (Fside/GREEN/EVEN Pixel)
Bit2: SSCG correction error (Fside/GREEN/ODD Pixel)
Bit1: SSCG correction error (Fside/BLUE/EVEN Pixel)
Bit0: SSCG correction error (Fside/BLUE/ODD Pixel)
Engine SP Mode Tables









4647[Scanner Hard Error]
4-647-001Power-ONENG[0 to 65535 / 0 / 1/step] Bit15: Unused
Bit14:SBU hardware error (Power ON/un-reset error)
Bit13:SBU hardware error (Serial communication error: F side)
Bit12:SBU hardware error (Reset error: F side) Bit11: Unused
Bit10: Unused
Bit9:SBU hardware error (Version error) Bit8: Unused
Bit7: Unused Bit6: Unused
Bit5:SBU hardware error (Serial communication error: L side)
Bit4:SBU hardware error (Reset error:Lside) Bit3: Unused
Bit2: Unused Bit1: Unused




4688[DF Density Adjustment]
4-688-001ARDF*ENG[80 to 120 / 106 / 1%/step]
4688[Scan Image Density Adjustment]
4-688-0021-pass DF*ENG[[80 to 120 / 101 / 1%/step]




4699[SBU Test Pattern Change]
4-699-001-ENG[0 to 255 / 0 / 1/step]




4700[CIS ID Display]
4-700-001-ENG[0x00 to 0xFF / 0 / 1/step]




4712[CIS GB Adj. Value: R]
4-712-001-*ENG[0 to 2048 / 1023 / 1digit/step]
4714[CIS GB Adj. Value: B]
4-714-001-*ENG[0 to 2048 / 1023 / 1digit/step]


4713[CIS GB Adj. Value: G]
4-713-001-*ENG[0 to 2048 / 1023 / 1digit/step]


Engine SP Mode Tables









4730[FROM ADF Factory Setting]
4-730-001CIS ParameterENG[0 or 1 / 0 / 0/step]
4730[FROM Main Factory Setting]
4-730-002Execution ON/OFFENG[0 or 1 / 0 / 0/step]
4-730-003Execution Flag*ENG[0 or 1 / 0 / 1/step]
4730[FROM Data Update]
4-730-004-ENG[0 to 1 / 0 / 0/step]




4745[CIS Image Level Error Flag]
4-745-001-ENG[0 to 65535 / 0 / 1/step]




4746[CIS GB Adj Error Flag]
4-746-001-ENG[0 to 7 / 0 / 1/step]




4747[CIS Hard Error Flag]
4-747-001-ENG[0 to 15 / 0 / 1/step]




4796[Low Density Color Correction]
4-796-001Front Side*ENG[0 to 3 / 0 / 1/step]
0: OFF
1: WEAK
2: MEDIUM
3: STRONG
4-796-002Rear Side*ENG[0 to 3 / 0 / 1/step]
0: OFF
1: WEAK
2: MEDIUM
3: STRONG




4797[Rear Side: Digital AE]
4-797-001Low Limit Setting*ENG[0 to 1023 / 364 / 1/step]
4-797-002Background Erase Level*ENG[512 to 1535 / 932 / 1/step]




4799[CIS TEST Pattern]
4-799-001selectENG[0 to 5 / 0 / 1/step]
Sets CIS test pattern output. 0: Scanned Image
1: Fixed Value Pattern
2: EO Fixed Value Pattern 3: Main Scan Gradation 4: Sub Scan Gradation
5: Grid Pattern
4-799-002Even Output Level SettingENG[0 to 1023 / 0 / 1digit/step]
4-799-003Odd Output Level SettingENG[0 to 1023 / 0 / 1digit/step]




4803[Home Position Adj Value]
4-803-001-ENG[-2.0 to 2.0 / 0 / 0.1mm/step]




4853[Partial LED ON]
4-853-001ON/OFF(Scan)*ENG[0 or 1 / 1 / 1/step]
4871[Distortion Corr.]
4-871-001Distortion Corr. ON/OFF*ENG[0 or 1 / 1 / 1/step]
4-871-002Distortion Initialization*ENG[0 to 3 / 0 / 1/step]
4-871-003Magnification Adjust(DF)*ENG[-0.35 to 0.35 / 0.11 / 0.01%/step]
4-871-004Magnification Adjust(FB)*ENG[-0.35 to 0.35 / 0 / 0.01%/step]


4-853-002ON/OFF(Size Detection)*ENG[0 or 1 / 1 / 1/step]


Engine SP Mode Tables









4902[Disp ACC Data]
4-902-001R_DATA1*ENG[0 to 255 / 0 / 1/step]
4-902-002G_DATA1*ENG[0 to 255 / 0 / 1/step]
4-902-003B_DATA1*ENG[0 to 255 / 0 / 1/step]
4-902-004R_DATA2*ENG[0 to 255 / 0 / 1/step]
4-902-005G_DATA2*ENG[0 to 255 / 0 / 1/step]
4-902-006B_DATA2*ENG[0 to 255 / 0 / 1/step]




4903[Filter Setting]
4-903-001Ind Dot Erase: Text*ENG[0 to 7 / 0 / 1/step]
4-903-002Ind Dot Erase: Generation Copy*ENG
[0 to 7 / 0 / 1/step]




4905[Select Gradation Level]
4-905-001-*ENG[0 to 255 / 0 / 1/step]




4918[Man Gamma Adj]
4-918-009-ENG[- / - / -]




4930[Coverage Ctrl: Text]
4-930-001Copy: Full Color 1ENG[0 to 400 / 200 / 1/step]
4-930-002Copy: Full Color 2ENG[0 to 400 / 200 / 1/step]
4-930-003Copy: Single ColorENG[0 to 400 / 100 / 1/step]
4-930-004Copy: Color ConversionENG[0 to 400 / 180 / 1/step]
4-930-005Coverage Ctrl OFFENG[0 to 400 / 400 / 1/step]




4931[Coverage Ctrl: Photo]
4-931-001Copy: Full Color 1ENG[0 to 400 / 240 / 1/step]
4-931-002Copy: Full Color 2ENG[0 to 400 / 260 / 1/step]
4-931-003Copy: Single ColorENG[0 to 400 / 100 / 1/step]
4-931-004Copy: Color ConversionENG[0 to 400 / 200 / 1/step]
4-931-005Coverage Ctrl OFFENG[0 to 400 / 400 / 1/step]




4938[ACS:Edge Mask]
4-938-001Copy:Sub LEdge*ENG[0 to 31 / 10 / 1mm/step]
4-938-002Copy:Sub TEdge*ENG[0 to 31 / 10 / 1mm/step]
4-938-003Copy:Main LEdge*ENG[0 to 31 / 10 / 1mm/step]
4-938-004Copy:Main TEdge*ENG[0 to 31 / 10 / 1mm/step]
4-938-005Scan:Sub LEdge*ENG[0 to 31 / 15 / 1mm/step]
4-938-006Scan:Sub TEdge*ENG[0 to 31 / 15 / 1mm/step]
4-938-007Scan:Main LEdge*ENG[0 to 31 / 15 / 1mm/step]
4-938-008Scan:Main TEdge*ENG[0 to 31 / 15 / 1mm/step]




4939[ACS:Color Range]
4-939-001-*ENG[-2 to 2 / 0 / 1/step]
Change the value of this SP to negative (“-1” or “-2”) when a black and white document is misjudged as a color document.
Engine SP Mode Tables









4954[Restore Test Chart]
4-954-005Chromaticity RankENG[0 to 255 / 0 / 1/step]




4958[Restore Test Chart: Rear]
4-958-005Chromaticity RankENG[0 to 255 / 0 / 1/step]




4984[IBACC Target Den]
4-984-001IBACC notch K*ENG[0 to 10 / 5 / 1/step]
4-984-002IBACC notch C*ENG
4-984-003IBACC notch M*ENG
4-984-004IBACC notch Y*ENG




4993[High Light Correction]
4-993-001Sensitivity SelectionENG[0 to 9 / 4 / 1/step]
0: Weak
9: Strong
4-993-002Range SelectionENG[0 to 9 / 4 / 1/step]
0: Weak
9: Strong




4994[Adj Txt/Photo Recog Level]
4-994-001High Compression PDFENG[0 to 2 / 1 / 1/step]




4996[White Paper Detection Level]
4-996-001-ENG[0 to 6 / 3 / 1/step]


Engine SP Mode Tables



  1. ENGINE SP TABLES - SP5000​

    1. SP5-XXX (MODE)​


      5126[Set F-size Document]
      5-126-001-ENG[0 to 2 / 0 / 1/step]
      0: 8 1/2 x13
      1: 8 1/4 x13
      2: 8 x13


      5131[Paper Size Type Selection]
      5-131-001-*ENG[0 to 2 / * / 1/step]
      *NA: 1, EU: 2, Asia: 2, CHN: 2, TWN: 2 ,
      KOR: 2
      ---
      0: JP (Japan)
      1: NA
      2: EU


      5135[LG_Oficio Change]
      5-135-001-*ENG[0 or 1 / 0 / 1/step]


      5181[Size Adjust]
      5-181-001TRAY 1*ENG[0 to 3 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: A4 LEF
      1: LT LEF
      2: B5 LEF
      3: A5 LEF
      5-181-002TRAY 2: 1*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: A4 LEF
      1: LT LEF
      5-181-003TRAY 2: 2*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: A3
      1: DLT
      5-181-004TRAY 2: 3*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: B4
      1: LG
      5-181-005TRAY 2: 4*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: B5LEF
      1: ExeLEF
      5-181-006TRAY 2: 5*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: SRA3
      1: 12X18
      5-181-007TRAY 3/T-LCT: 1*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: A4LEF
      1: LTLEF
      5-181-008TRAY 3: 2*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: A3
      1: DLT
      5-181-009TRAY 3: 3*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: B4
      1: LG
      5-181-010TRAY 3: 4*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: B5LEF
      1: ExeLEF
      5-181-011TRAY 3: 5*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: 12.6X17.7
      1: 12X18
      5-181-012TRAY 4: 1*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: A4LEF
      1: LTLEF
      5-181-013TRAY 4: 2*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: A3
      1: DLT
      5-181-014TRAY 4: 3*ENG[0 or 1 / * / 1/step]
      NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: B4
      1: LG
      5-181-015TRAY 4: 4*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: B5LEF
      1: ExeLEF
      Engine SP Mode Tables


      5-181-016TRAY 4: 5*ENG[0 or 1 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: 12.6X17.7
      1: 12X18
      5-181-017LCT*ENG[0 to 2 / * / 1/step]
      *NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
      KOR: 0
      0: A4LEF
      1: LTLEF
      2: B5LEF


      5186[RK4]
      5-186-001-*ENG[0 or 1 / 0 / 1/step]


      5610[Base Gamma Ctrl Pt:Execute]
      5-610-004Get Factory DefaultENG[0 or 1 / 0 / 1/step]
      5-610-005Set Factory DefaultENG[0 or 1 / 0 / 1/step]
      5-610-006Restore Orginal ValueENG[0 or 1 / 0 / 1/step]


      5611[Toner Color in 2C]
      5-611-001B-C*ENG[0 to 128 / 100 / 1/step]
      5-611-002B-M*ENG[0 to 128 / 100 / 1/step]
      5-611-003G-C*ENG[0 to 128 / 100 / 1/step]
      5-611-004G-Y*ENG[0 to 128 / 100 / 1/step]
      5-611-005R-M*ENG[0 to 128 / 100 / 1/step]
      5-611-006R-Y*ENG[0 to 128 / 100 / 1/step]


      5801[Memory Clear]
      5803[INPUT Check]
      See page 3-385 "Input Check Table"

      5-801-002EngineENG[- / - / -]
      [Execute]

      Engine SP Mode Tables



      5804[OUTPUT Check]
      See page 3-412 "Output Check Table"


      5805[Anti-Condensation Heater]
      5-805-0010:OFF / 1:ON*ENG[0 or 1 / 0 / 1/step]
      0: OFF... Switches OFF when standby (default setting)
      1: ON... Switches ON when standby


      5810[SC Reset]
      5-810-001Fusing SC ResetENGClears the fusing SC.
      5-810-002Hard High Temp. DetectionENGClears the fusing hardware SC.


      5811[MachineSerial]
      5-811-002Display*ENG[0 to 255 / 0 / 1/step]
      5811[MachineSerial Set]
      5-811-004BCU*ENG[0 to 255 / 0 / 1/step]
      5811[Machine Serial: Update Date]
      5-811-021Latest*ENG[0 or 1 / 0 / 1/step]
      5-811-022Previous*ENG[0 or 1 / 0 / 1/step]
      5811[MachineSerial]
      5-811-023Previous*ENG[0 to 255 / 0 / 1/step]
      5811[Machine Serial: Update Date]
      5-811-024Latest (BCU)*ENG[0 or 1 / 0 / 1/step]
      5-811-025Previous (BCU)*ENG[0 or 1 / 0 / 1/step]
      5811[MachineSerial]
      5-811-026Previous (BCU)*ENG[0 to 255 / 0 / 1/step]


      5894[External Mech Count Setting]
      5-894-001Mech Counter Switch Setting*ENG[0 to 2 / 0 / 1/step]


      5900[Engine Log Upload]
      5-900-001Pattern*ENG[0 to 4 / 0 / 1/step]
      5-900-002Trigger*ENG[0 to 3 / 0 / 1/step]


      5998[Fusing Warm UP]
      5-998-001Warm Up In Advance ON/OFF*ENG[0 or 1 / 0 / 1/step]

      Engine SP Mode Tables

  2. ENGINE SP TABLES - SP6000​

    1. SP6-XXX (PERIPHERALS)​


      6006[ADF Adjustment]
      6-006-001Side-to-Side Regist: Front*ENG[-3.0 to 3.0 / 0 / 0.1mm/step]
      6-006-002Side-to-Side Regist: Rear*ENG[-3.0 to 3.0 / 0 / 0.1mm/step]
      6-006-003Leading Edge Registration: Front*ENG[-5.0 to 5.0 / 0 / 0.1mm/step]
      6-006-004Leading Edge Registration: Rear*ENG[-5.0 to 5.0 / 0 / 0.1mm/step]
      6-006-005Buckle: Duplex Front*ENG[-5.0 to 5.0 / 0 / 0.1mm/step]
      6-006-006Buckle: Duplex Rear*ENG[-5.0 to 5.0 / 0 / 0.1mm/step]
      6-006-007Rear Edge Erase Front*ENG[-10.0 to 10.0 / -2.3 / 0.1mm/step]
      6-006-008Rear Edge Erase Rear*ENG[-10.0 to 10.0 / -2.3 / 0.1mm/step]
      6-006-010L-Edge Regist (1-Pass): Front*ENG[-5.0 to 5.0 / 0 / 0.1mm/step]
      6-006-011L-Edge Regist (1-Pass): Rear*ENG[-5.0 to 5.0 / 0 / 0.1mm/step]
      6-006-0121st Buckle (1-Pass)*ENG[-3.0 to 3.0 / 0 / 0.1mm/step]
      6-006-0132nd Buckle (1-Pass)*ENG[-2.0 to 3.0 / 0 / 0.1mm/step]
      6-006-014T-Edge Erase (1-Pass): Front*ENG[-5.0 to 5.0 / -3.0 / 0.1mm/step]
      6-006-015T-Edge Erase (1-Pass): Rear*ENG[-5.0 to 5.0 / -2.5 / 0.1mm/step]


      6007[ADF INPUT Check]
      See page 3-385 "Input Check Table"
      6008[ADF OUTPUT Check]
      See page 3-412 "Output Check Table"


      6009[ADF FreeRun]
      6-009-001Free Run Simplex MotionENG[0 or 1 / 0 / 1/step]
      6-009-002Free Run Duplex MotionENG[0 or 1 / 0 / 1/step]
      6-009-003Free Run Stamp MotionENG[0 or 1 / 0 / 1/step]
      6-009-004Free Run Simplex Motion(low speed)ENG[0 or 1 / 0 / 1/step]
      6-009-005Free Run Simplex Motion(high speed)ENG[0 or 1 / 0 / 1/step]
      6-009-006Free Run Duplex Motion(low speed)ENG[0 or 1 / 0 / 1/step]
      6-009-007Free Run Duplex Motion(high speed)ENG[0 or 1 / 0 / 1/step]


      6010[Stamp Position Adj.]
      6-010-001-*ENG[-5.0 to 5.0 / 0 / 0.1mm/step]


      6011[1-Pass ADF INPUT Check]
      See page 3-385 "Input Check Table"


      6012[1-Pass ADF OUTPUT Check]
      See page 3-412 "Output Check Table"


      6016[Original Size Detect Setting]
      6-016-001-*ENG[0 to 255 / 0 / 1/step]


      6017[DF Magnification Adj.]
      6020[Skew Correction Moving Setting]
      6-020-001-*ENG[0 or 1 / 0 / 1/step]

      6-017-001-*ENG[-5 to 5 / 0 / 0.1%/step]

      Engine SP Mode Tables



      6121[NV Adj. Data Mod.]
      6-121-001Jogger Pos. Factory Adj.ENG[-3 to 3 / 0 / 0.5mm/step]
      6-121-002Folding Pos. Factory Adj.ENG[-1.4 to 1.4 / 0 / 0.2mm/step]


      6125[Use Paper Guide(Big Size)]
      6-125-001All SizeENG[0 or 1 / 0 / 1/step]


      6126[Use Paper Guide(Small Size)]
      6-126-001All SizeENG[0 or 1 / 0 / 1/step]


      6130[Sub-scan PunchPosAdj:FrontFIN]
      6-130-001Domestic 2Hole(Europe 2Hole)ENG[-7.5 to 7.5 / 0 / 0.5mm/step]
      6-130-002North America 3HoleENG
      6-130-003Europe 4HoleENG
      6-130-004North Europe 4HoleENG
      6-130-005North America 2HoleENG


      6131[Main-scan PunchPosAdj:FrontFIN]
      6-131-001Domestic 2Hole(Europe 2Hole)ENG[-2 to 2 / 0 / 0.4mm/step]
      6-131-002North America 3HoleENG
      6-131-003Europe 4HoleENG
      6-131-004North Europe 4HoleENG
      6-131-005North America 2HoleENG


      6132[Jogger Fence Fine Adj:FrontFIN]
      6-132-001A3TENG[-1.5 to 1.5 / 0 / 0.5mm/step]
      6-132-002B4TENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-003A4TENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-004A4YENG[-1.5 to 1.5 / 0 / 0.5mm/step]
      6-132-005B5TENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-006B5YENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-007DLT-TENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-008LG-TENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-009Oficio-TENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-010LT-TENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-011LT-YENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-0128K-TENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-01316K-TENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-01416K-YENG[-3 to 3 / 0 / 0.5mm/step]
      6-132-015OtherENG[-3 to 3 / 0 / 0.5mm/step]


      6133[Staple Position Adj: FrontFIN]
      6-133-001Finisher1ENG[-2 to 2 / 0 / 0.5mm/step]


      6134[Finisher Free Run: FrontFIN]
      6-134-001Free Run1ENG[0 or 1 / 0 / 1/step]
      6-134-002Free Run2ENG[0 or 1 / 0 / 1/step]
      6135[INPUT Check: FrontFIN]
      See page 3-385 "Input Check Table"

      6-134-003Free Run3ENG[0 or 1 / 0 / 1/step]
      6-134-004Free Run4ENG[0 or 1 / 0 / 1/step]

      Engine SP Mode Tables



      6136[OUTPUT Check: FrontFIN]
      See page 3-412 "Output Check Table"


      6140[Staple Position Adj: 1K FIN]
      6-140-001-ENG[-3.5 to 3.5 / 0 / 0.5mm/step]
      6-140-002-ENG[-3 to 3 / 0 / 0.3mm/step]


      6141[Booklet Stapler Pos Adj:1K FIN]
      6-141-001A3 SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-141-002B4 SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-141-003A4 SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-141-004B5 SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-141-005DLT SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-141-006LG SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-141-007Oficio SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-141-008LT SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-141-00912"x18"ENG[-3 to 3 / 0 / 0.2mm/step]


      6142[Sub-scan Punch Pos Adj:1K FIN]
      6-142-001JPN/EU: 2-HoleENG[-7.5 to 7.5 / 0 / 0.5mm/step]
      6-142-002NA: 3-HoleENG
      6-142-003Europe: 4-HoleENG
      6-142-004NEU: 4-HoleENG
      6-142-005NA: 2-HoleENG


      6143[Jogger Pos Adj:1K FIN]
      6-143-001A3 SEFENG
      [-1.5 to 1.5 / 0 / 0.5mm/step]
      6-143-002B4 SEFENG
      6-143-003A4 SEFENG
      6-143-004A4 LEFENG
      6-143-005B5 SEFENG
      6-143-006B5 LEFENG
      [-1.5 to 1.5 / 0 / 0.5mm/step]
      6-143-007DLT SEFENG
      6-143-008LG SEFENG
      6-143-009Oficio SEFENG
      6-143-010LT SEFENG
      6-143-011LT LEFENG
      6-143-01212"x18"ENG
      6-143-0138K SEFENG
      [-1.5 to 1.5 / 0 / 0.5mm/step]
      6-143-01416K SEFENG
      6-143-01516K LEFENG
      6-143-016OtherENG


      6144[Main-scan Punch Pos Adj:1K FIN]
      6-144-001JPN/EU: 2-HoleENG[-2 to 2 / 0 / 0.4mm/step]
      6-144-002NA: 3-HoleENG
      6-144-003Europe: 4-HoleENG
      6145[Skew Correct Buckle Adj:1K FIN]
      6-145-001A3 SEFENG
      [-5 to 5 / 0 / 0.2mm/step]
      6-145-002B4 SEFENG
      6-145-003A4 SEFENG
      6-145-004A4 LEFENG
      6-145-005B5 SEFENG
      6-145-006B5 LEFENG
      [-5 to 5 / 0 / 0.2mm/step]
      6-145-007A5 LEFENG
      6-145-008DLT SEFENG
      6-145-009LG SEFENG
      6-145-010Oficio SEFENG
      6-145-011LT SEFENG
      [-5 to 5 / 0 / 0.2mm/step]
      6-145-012LT LEFENG
      6-145-013HLT LEFENG
      6-145-01412"x18"ENG
      6-145-0158K SEFENG
      6-145-01616K SEFENG
      6-145-01716K LEFENG
      6-145-018OtherENG[-5 to 5 / 0 / 0.2mm/step]

      6-144-004NEU: 4-HoleENG
      6-144-005NA: 2-HoleENG

      Engine SP Mode Tables




      6146[Skew Correct Ctrl SW:1K FIN]
      6-146-001A3 SEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-002B4 SEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-003A4 SEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-004A4 LEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-005B5 SEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-006B5 LEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-007A5 LEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-008DLT SEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-009LG SEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-010Oficio SEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-011LT SEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-012LT LEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-013HLT LEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-01412"x18"ENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-0158K SEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-01616K SEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-01716K LEFENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      6-146-018OtherENG[0 or 1 / 0 / 1/step]
      0: enable
      1: disable
      Engine SP Mode Tables




      6147[Booklet Folder Pos Adj:1K FIN]
      6-147-001A3 SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-002B4 SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-003A4 SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-004B5 SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-005DLT SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-006LG SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-007Oficio SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-008LT SEFENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-00912"x18"ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-010A3 SEF(1-5)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-011A3 SEF(6-10)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-012A3 SEF(11-over)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-013B4 SEF(1-5)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-014B4 SEF(6-10)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-015B4 SEF(11-over)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-016A4 SEF(1-5)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-017A4 SEF(6-10)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-018A4 SEF(11-over)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-019B5 SEF(1-5)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-020B5 SEF(6-10)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-021B5 SEF(11-over)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-022DLT SEF(1-5)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-023DLT SEF(6-10)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-024DLT SEF(11-over)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-025LG SEF(1-5)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-026LG SEF(6-10)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-027LG SEF(11-over)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-028Oficio SEF(1-5)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-029Oficio SEF(6-10)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-030Oficio SEF(11-over)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-031LT SEF(1-5)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-032LT SEF(6-10)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-033LT SEF(11-over)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-03412"x18"(1-5)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-03512"x18"(6-10)ENG[-3 to 3 / 0 / 0.2mm/step]
      6-147-03612"x18"(11-over)ENG[-3 to 3 / 0 / 0.2mm/step]
      6149[Last Paper Pos Time Adj:1K FIN]
      6-149-001-*ENG[0 to 1 / 0 / 1time/step]

      6148[Fold Times Adj: 1K FIN]
      6-148-001-ENG[0 to 29 / 0 / 1sec/step]

      Engine SP Mode Tables




      6150[PositioningStrtTimingAdj:1KFIN]
      6-150-001A3 SEFENG[-100 to 100 / 0 / 10msec/step]
      6-150-002B4 SEFENG
      6-150-003A4 SEFENG
      6-150-004A4 LEFENG
      6-150-005B5 SEFENG
      6-150-006B5 LEFENG
      6-150-007DLT SEFENG
      6-150-008LG SEFENG
      6-150-009Oficio SEFENG
      6-150-010LT SEFENG
      6-150-011LT LEFENG
      6-150-01212"x18"ENG
      6-150-0138K SEFENG
      6-150-01416K SEFENG
      6-150-01516K LEFENG
      6-150-016OtherENG


      6151[PosTimeAdj(LstPr2ndTime):1KFIN]
      6-151-001-ENG[-100 to 100 / 0 / 10msec/step]

      6152[PosTiAdj(ExcLstPr3rdTi):1KFIN]
      6-152-001A3 SEFENG[-100 to 100 / 0 / 10msec/step]
      6-152-002B4 SEFENG
      6-152-003A4 SEFENG
      6-152-004A4 LEFENG
      6-152-005B5 SEFENG
      6-152-006B5 LEFENG
      6-152-007DLT SEFENG
      6-152-008LG SEFENG
      6-152-009Oficio SEFENG
      6-152-010LT SEFENG
      6-152-011LT LEFENG
      6-152-01212"x18"ENG
      6-152-0138K SEFENG
      6-152-01416K SEFENG
      6-152-01516K LEFENG
      6-152-016OtherENG


      6154[Pos Time Adj By Sheet: 1K FIN]
      6-154-0011 - 10 SheetsENG[-100 to 100 / 0 / 10msec/step]
      6-154-00211 - 20 SheetsENG
      6-154-00321 - 30 SheetsENG
      6-154-00431 - 40 SheetsENG
      6-154-00541 - 50 SheetsENG
      6156[Paper Guide Retra Adj: 1K FIN]
      6-156-001-ENG[-50 to 50 / 0 / 5mm/step]

      6155[Paper Guide Poss Adj: 1K FIN]
      6-155-001-ENG[-10 to 10 / 0 / 1mm/step]

      Engine SP Mode Tables



      6157[Paper Guide Acept Adj: 1K FIN]
      6-157-001-ENG[-50 to 50 / 0 / 5msec/step]


      6160[Finisher Free Run: 1K FIN]
      6-160-001Free Run 1ENG[0 or 1 / 0 / 1/step]
      6-160-002Free Run 2ENG[0 or 1 / 0 / 1/step]
      6-160-003Free Run 3ENG[0 or 1 / 0 / 1/step]
      6-160-004Free Run 4ENG[0 or 1 / 0 / 1/step]


      6161[FIN (1K FIN) INPUT Check]
      See page 3-385 "Input Check Table"


      6162[FIN (1K FIN) OUTPUT Check]
      See page 3-412 "Output Check Table"


      6163[Use Paper Guide]
      6-163-001Big SizeENG[0 or 1 / 1 / 1/step]
      6-163-002Small SizeENG[0 or 1 / 0 / 1/step]


      6164[NV Adj. Data Mod. 1KShtFIN]
      6-164-001Jogger Pos. Factory Adj.ENG[-1.5 to 1.5 / 0 / 0.5mm/step]
      6-164-002Stapling Pos. Factory Adj.ENG[-2 to 2 / 0 / 0.5mm/step]
      6164[NV Adj. Data Mod. 1KShtFIN HY]
      6-164-003Stapling Pos. Factory Adj. (HY)ENG[-2.1 to 2.1 / 0 / 0.3mm/step]
      6-164-004Stapleless Stapling Pos. Factory Adj.
      ENG
      [-2.1 to 2.1 / 0 / 0.3mm/step]
      6164[NV Adj. Data Mod. 1KShtFIN]
      6-164-005Folding Pos. Factory Adj.ENG[-2 to 2 / 0 / 0.1mm/step]


      6180[M-ScanBindPosAdj:NoStplBindFIN]
      6-180-001-ENG[-1 to 1 / 0 / 0.5mm/step]


      6181[BindSpeedSetting:NoStplBindFIN]
      6-181-001-ENG[1 to 3 / 3 / 2/step]


      6182[ExitSpeedSwitch:NoStplBindFIN]
      6-182-001PaperLength:297.0-457.2mm,Thick(106-300g/m2)ENG[1 to 5 / 2 / 1/step]
      6-182-002PaperLength:297.0-457.2mm,Plain(60-105g/m2)ENG[1 to 5 / 2 / 1/step]
      6-182-003PaperLength:297.0-457.2mm,Thin(52-59g/m2)ENG[1 to 5 / 4 / 1/step]
      6-182-004PaperLength:210.0-296.9mm,Thick(106-300g/m2)ENG[1 to 5 / 2 / 1/step]
      6-182-005PaperLength:210.0-296.9mm,Plain(60-105g/m2)ENG[1 to 5 / 2 / 1/step]
      6-182-006PaperLength:210.0-296.9mm,Thin(52-59g/m2)ENG[1 to 5 / 4 / 1/step]
      6-182-007PaperLength:148.0-209.9mm,Thick(106-300g/m2)ENG[1 to 5 / 2 / 1/step]
      6-182-008PaperLength:148.0-209.9mm,Plain(60-105g/m2)ENG[1 to 5 / 2 / 1/step]
      6-182-009PaperLength:148.0-209.9mm,Thin(52-59g/m2)ENG[1 to 5 / 4 / 1/step]


      6183[FinisherFreeRun:NoStplBindFIN]
      6-183-001Free Run 1ENG[0 or 1 / 0 / 0/step]
      6184[Input Check:NoStplBindFIN]
      See page 3-385 "Input Check Table"

      6-183-002Free Run 2ENG[0 or 1 / 0 / 0/step]
      6-183-003Free Run 3ENG[0 or 1 / 0 / 0/step]

      Engine SP Mode Tables



      6185[Output Check:NoStplBindFIN]
      See page 3-412 "Output Check Table"


      6186[BindTimes NoStplBindFIN]
      6-186-001-*ENG[1 to 2 / 2 / 1/step]


      6801[1-pass Stamp Unit]
      6-801-001-*ENG[0 or 1 / 0 / 1/step]
      0: NO
      1: YES


      6900[ADF Bottom Plate Setting]
      6-900-001-*ENG[0 or 1 / 0 / 1/step]


      6901[ADF Operation Setting]
      Setting to give priority to stackability.
      6-901-001-ENG[0 or 1 / 0 / 1/step]
      0: Higher quietness
      1: Higher throughput
      6-901-002-ENG[0 or 1 / 0 / 1/step]
      0: Normal
      1: Higher stackability
      7622[PM Counter Reset]
      7-622-002# PCU:KENG[0 or 1 / 0 / 1/step]
      7-622-003# Dev Unit:KENG[0 or 1 / 0 / 1/step]
      7-622-004Developer:KENG[0 or 1 / 0 / 1/step]
      7-622-025# PCU:CENG[0 or 1 / 0 / 1/step]
      7-622-026# Dev Unit:CENG[0 or 1 / 0 / 1/step]
      7-622-027Developer:CENG[0 or 1 / 0 / 1/step]
      7-622-048# PCU:MENG[0 or 1 / 0 / 1/step]
      7-622-049# Dev Unit:MENG[0 or 1 / 0 / 1/step]
      7-622-050Developer:MENG[0 or 1 / 0 / 1/step]
      7-622-071# PCU:YENG[0 or 1 / 0 / 1/step]
      7-622-072# Dev Unit:YENG[0 or 1 / 0 / 1/step]
      7-622-073Developer:YENG[0 or 1 / 0 / 1/step]
      7-622-093# ITB UnitENG[0 or 1 / 0 / 1/step]
      7-622-102# ITB Cleaning UnitENG[0 or 1 / 0 / 1/step]
      7-622-109# PTR UnitENG[0 or 1 / 0 / 1/step]
      7-622-115# Fusing UnitENG[0 or 1 / 0 / 1/step]
      7-622-116Fusing BeltENG[0 or 1 / 0 / 1/step]
      7-622-118Pressure RollerENG[0 or 1 / 0 / 1/step]
      7-622-131Dust FilterENG[0 or 1 / 0 / 1/step]
      7-622-206ADF Pick-up RollerENG[0 or 1 / 0 / 1/step]
      7-622-207ADF Supply BeltENG[0 or 1 / 0 / 1/step]
      7-622-208ADF Reverse RollerENG[0 or 1 / 0 / 1/step]

      7-621-207ADF Supply BeltENG[0 to 99999999 / 0 / 1page/step]
      7-621-208ADF Reverse RollerENG[0 to 99999999 / 0 / 1page/step]

      Engine SP Mode Tables

  3. ENGINE SP TABLES - SP7000​

    1. SP7-XXX (DATA LOG)​



7621[PM Counter Display: Pages]
7-621-002# PCU:KENG[0 to 99999999 / 0 / 1page/step]
7-621-003# Dev Unit:K*ENG[0 to 99999999 / 0 / 1page/step]
7-621-004Developer:KENG[0 to 99999999 / 0 / 1page/step]
7-621-025# PCU:CENG[0 to 99999999 / 0 / 1page/step]
7-621-026# Dev Unit:C*ENG[0 to 99999999 / 0 / 1page/step]
7-621-027Developer:CENG[0 to 99999999 / 0 / 1page/step]
7-621-048# PCU:MENG[0 to 99999999 / 0 / 1page/step]
7-621-049# Dev Unit:M*ENG[0 to 99999999 / 0 / 1page/step]
7-621-050Developer:MENG[0 to 99999999 / 0 / 1page/step]
7-621-071# PCU:YENG[0 to 99999999 / 0 / 1page/step]
7-621-072# Dev Unit:Y*ENG[0 to 99999999 / 0 / 1page/step]
7-621-073Developer:YENG[0 to 99999999 / 0 / 1page/step]
7-621-093# ITB UnitENG[0 to 99999999 / 0 / 1page/step]
7-621-102# ITB Cleaning UnitENG[0 to 99999999 / 0 / 1page/step]
7-621-109# PTR UnitENG[0 to 99999999 / 0 / 1page/step]
7-621-115# Fusing UnitENG[0 to 99999999 / 0 / 1page/step]
7-621-116Fusing BeltENG[0 to 99999999 / 0 / 1page/step]
7-621-118Pressure RollerENG[0 to 99999999 / 0 / 1page/step]
7-621-131Dust FilterENG[0 to 99999999 / 0 / 1page/step]
7-621-142Waste Toner BottleENG[0 to 999999999 / 0 / 1mg/step]
7-621-206ADF Pick-up RollerENG[0 to 99999999 / 0 / 1page/step]
7-622-245PCU:All ColorsENG[0 or 1 / 0 / 1/step]

7-622-246		Development Unit:All ColorsENG[0 or 1 / 0 / 1/step]
7-622-247Developer:All ColorsENG[0 or 1 / 0 / 1/step]
7-622-250SCSENG[0 or 1 / 0 / 1/step]




7623[PM Value Setting: Life Pages]
7-623-002# PCU:KENG[0 to 99999999 / 0 / 1page/step]
7-623-003# Dev Unit:KENG[0 to 99999999 / 0 / 1page/step]
7-623-004Developer:KENG[0 to 99999999 / 0 / 1page/step]
7-623-025# PCU:CENG[0 to 99999999 / 0 / 1page/step]
7-623-026# Dev Unit:CENG[0 to 99999999 / 0 / 1page/step]
7-623-027Developer:CENG[0 to 99999999 / 0 / 1page/step]
7-623-048# PCU:MENG[0 to 99999999 / 0 / 1page/step]
7-623-049# Dev Unit:MENG[0 to 99999999 / 0 / 1page/step]
7-623-050Developer:MENG[0 to 99999999 / 0 / 1page/step]
7-623-071# PCU:YENG[0 to 99999999 / 0 / 1page/step]
7-623-072# Dev Unit:YENG[0 to 99999999 / 0 / 1page/step]
7-623-073Developer:YENG[0 to 99999999 / 0 / 1page/step]
7-623-093# ITB UnitENG[0 to 99999999 / 240000 / 1page/step]
7-623-102# ITB Cleaning UnitENG[0 to 99999999 / 240000 / 1page/step]
7-623-109# PTR UnitENG[0 to 99999999 / 240000 / 1page/step]
7-623-115# Fusing UnitENG[0 to 99999999 / 240000 / 1page/step]
7-623-116Fusing BeltENG[0 to 99999999 / 240000 / 1page/step]
7-623-118Pressure RollerENG[0 to 99999999 / 240000 / 1page/step]
7-623-131Dust FilterENG[0 to 99999999 / 300000 / 1page/step]
7-623-142Waste Toner BottleENG[0 to 999999999 / 1200000 / 1mg/step]
7-623-206ADF Pick-up RollerENG[0 to 99999999 / 120000 / 1page/step]
7-623-207ADF Supply BeltENG[0 to 99999999 / 120000 / 1page/step]
7-623-208ADF Reverse RollerENG[0 to 99999999 / 120000 / 1page/step]
Engine SP Mode Tables









7625[Previous Unit Counter: Pages]
7-625-002# PCU:KENG[0 to 99999999 / 0 / 1page/step]
7-625-003# Dev Unit:KENG[0 to 99999999 / 0 / 1page/step]
7-625-004Developer:KENG[0 to 99999999 / 0 / 1page/step]
7-625-025# PCU:CENG[0 to 99999999 / 0 / 1page/step]
7-625-026# Dev Unit:CENG[0 to 99999999 / 0 / 1page/step]
7-625-027Developer:CENG[0 to 99999999 / 0 / 1page/step]
7-625-048# PCU:MENG[0 to 99999999 / 0 / 1page/step]
7-625-049# Dev Unit:MENG[0 to 99999999 / 0 / 1page/step]
7-625-050Developer:MENG[0 to 99999999 / 0 / 1page/step]
7-625-071# PCU:YENG[0 to 99999999 / 0 / 1page/step]
7-625-072# Dev Unit:YENG[0 to 99999999 / 0 / 1page/step]
7-625-073Developer:YENG[0 to 99999999 / 0 / 1page/step]
7-625-093# ITB UnitENG[0 to 99999999 / 0 / 1page/step]
7-625-102# ITB Cleaning UnitENG[0 to 99999999 / 0 / 1page/step]
7-625-109# PTR UnitENG[0 to 99999999 / 0 / 1page/step]
7-625-115# Fusing UnitENG[0 to 99999999 / 0 / 1page/step]
7-625-116Fusing BeltENG[0 to 99999999 / 0 / 1page/step]
7-625-118Pressure RollerENG[0 to 99999999 / 0 / 1page/step]
7-625-131Dust FilterENG[0 to 99999999 / 0 / 1page/step]
7-625-142Waste Toner BottleENG[0 to 99999999 / 0 / 1page/step]
7-625-206ADF Pick-up RollerENG[0 to 99999999 / 0 / 1page/step]
7-625-207ADF Supply BeltENG[0 to 99999999 / 0 / 1page/step]
7-625-208ADF Reverse RollerENG[0 to 99999999 / 0 / 1page/step]




7626[Previous Unit Counter2: Pages]
7-626-002# PCU:KENG[0 to 99999999 / 0 / 1page/step]
7-626-003# Dev Unit:KENG[0 to 99999999 / 0 / 1page/step]
7-626-004Developer:KENG[0 to 99999999 / 0 / 1page/step]
7-626-025# PCU:CENG[0 to 99999999 / 0 / 1page/step]
7-626-026# Dev Unit:CENG[0 to 99999999 / 0 / 1page/step]
7-626-027Developer:CENG[0 to 99999999 / 0 / 1page/step]
7-626-048# PCU:MENG[0 to 99999999 / 0 / 1page/step]
7-626-049# Dev Unit:MENG[0 to 99999999 / 0 / 1page/step]
7-626-050Developer:MENG[0 to 99999999 / 0 / 1page/step]
7-626-071# PCU:YENG[0 to 99999999 / 0 / 1page/step]
7-626-072# Dev Unit:YENG[0 to 99999999 / 0 / 1page/step]
7-626-073Developer:YENG[0 to 99999999 / 0 / 1page/step]
7-626-093# ITB UnitENG[0 to 99999999 / 0 / 1page/step]
7-626-102# ITB Cleaning UnitENG[0 to 99999999 / 0 / 1page/step]
7-626-109# PTR UnitENG[0 to 99999999 / 0 / 1page/step]
7-626-115# Fusing UnitENG[0 to 99999999 / 0 / 1page/step]
7-626-116Fusing BeltENG[0 to 99999999 / 0 / 1page/step]
7-626-118Pressure RollerENG[0 to 99999999 / 0 / 1page/step]
7-626-131Dust FilterENG[0 to 99999999 / 0 / 1page/step]
7-626-142Waste Toner BottleENG[0 to 999999999 / 0 / 1mg/step]
7-626-206ADF Pick-up RollerENG[0 to 99999999 / 0 / 1page/step]
7628[PM Counter Reset]
7-628-002SCSENG[0 or 1 / 0 / 1/step]


7-626-207ADF Supply BeltENG[0 to 99999999 / 0 / 1page/step]
7-626-208ADF Reverse RollerENG[0 to 99999999 / 0 / 1page/step]


Engine SP Mode Tables







7720[Ave. Cvrg for Eng.]
7-720-001K*ENG[0 to 100 / 0 / 0.01%/step]
7-720-002C*ENG[0 to 100 / 0 / 0.01%/step]
7-720-003M*ENG[0 to 100 / 0 / 0.01%/step]
7-720-004Y*ENG[0 to 100 / 0 / 0.01%/step]




7801[ROM No.]
7-801-002EngineENG[- / - / -]
7-801-005ADFENG[- / - / -]
7-801-007FinisherENG[- / - / -]
7-801-009PTUENG[- / - / -]
7-801-010LCTENG[- / - / -]
7-801-019PTU2ENG[- / - / -]
7801[ROM No./ Firmware Version]
7-801-102EngineENG[- / - / -]
7-801-105ADFENG[- / - / -]
7-801-107FinisherENG[- / - / -]
7-801-109PTUENG[- / - / -]
7-801-110LCTENG[- / - / -]




7852[DF Glass Dust Check]
7-852-001Dust Detection Counter*ENG[0 to 65535 / 0 / 1/step]

7-852-002		Dust Counter Clear Counter*ENG[0 to 65535 / 0 / 1/step]

7-852-003		Dust Detection Counter: Back*ENG[0 to 65535 / 0 / 1/step]




7853[Replace Counter]
7-853-002# PCU:KENG[0 to 255 / 0 / 1/step]
7-853-003# Dev Unit:KENG[0 to 255 / 0 / 1/step]
7-853-004Developer:KENG[0 to 255 / 0 / 1/step]
7-853-025# PCU:CENG[0 to 255 / 0 / 1/step]
7-853-026# Dev Unit:CENG[0 to 255 / 0 / 1/step]
7-853-027Developer:CENG[0 to 255 / 0 / 1/step]
7-853-048# PCU:MENG[0 to 255 / 0 / 1/step]
7-853-049# Dev Unit:MENG[0 to 255 / 0 / 1/step]
7-853-050Developer:MENG[0 to 255 / 0 / 1/step]
7-853-071# PCU:YENG[0 to 255 / 0 / 1/step]
7-853-072# Dev Unit:YENG[0 to 255 / 0 / 1/step]
7-853-073Developer:YENG[0 to 255 / 0 / 1/step]
7-853-093# ITB UnitENG[0 to 255 / 0 / 1/step]
7-853-102# ITB Cleaning UnitENG[0 to 255 / 0 / 1/step]
7-853-109# PTR UnitENG[0 to 255 / 0 / 1/step]
7-853-115# Fusing UnitENG[0 to 255 / 0 / 1/step]
7-853-116Fusing BeltENG[0 to 255 / 0 / 1/step]
7-853-118Pressure RollerENG[0 to 255 / 0 / 1/step]
7-853-131Dust FilterENG[0 to 255 / 0 / 1/step]
7-853-142Waste Toner BottleENG[0 to 255 / 0 / 1/step]
7-853-206ADF Pick-up RollerENG[0 to 255 / 0 / 1/step]
7-853-207ADF Supply BeltENG[0 to 255 / 0 / 1/step]
7-853-208ADF Reverse RollerENG[0 to 255 / 0 / 1/step]
Engine SP Mode Tables









7906[Previous Unit Counter:Distance]
7-906-002# PCU:KENG[0 to 4294967295 / 0 / 1mm/step]
7-906-003# Dev Unit:KENG[0 to 4294967295 / 0 / 1mm/step]
7-906-004Developer:KENG[0 to 4294967295 / 0 / 1mm/step]
7-906-025# PCU:CENG[0 to 4294967295 / 0 / 1mm/step]
7-906-026# Dev Unit:CENG[0 to 4294967295 / 0 / 1mm/step]
7-906-027Developer: CENG[0 to 4294967295 / 0 / 1mm/step]
7-906-048# PCU:MENG[0 to 4294967295 / 0 / 1mm/step]
7-906-049# Dev Unit:MENG[0 to 4294967295 / 0 / 1mm/step]
7-906-050Developer: MENG[0 to 4294967295 / 0 / 1mm/step]
7-906-071# PCU:YENG[0 to 4294967295 / 0 / 1mm/step]
7-906-072# Dev Unit:YENG[0 to 4294967295 / 0 / 1mm/step]
7-906-073Developer: YENG[0 to 4294967295 / 0 / 1mm/step]
7-906-093# ITB UnitENG[0 to 4294967295 / 0 / 1mm/step]
7-906-102# ITB Cleaning UnitENG[0 to 4294967295 / 0 / 1mm/step]
7-906-109# PTR UnitENG[0 to 4294967295 / 0 / 1mm/step]
7-906-115# Fusing UnitENG[0 to 4294967295 / 0 / 1mm/step]
7-906-116Fusing BeltENG[0 to 4294967295 / 0 / 1mm/step]
7-906-118Pressure RollerENG[0 to 4294967295 / 0 / 1mm/step]
7-906-230Low Speed: # PCU:KENG[0 to 4294967295 / 0 / 1mm/step]
7-906-231Low Speed: # PCU:CENG[0 to 4294967295 / 0 / 1mm/step]
7-906-232Low Speed: # PCU:MENG[0 to 4294967295 / 0 / 1mm/step]
7-906-233Low Speed: # PCU:YENG[0 to 4294967295 / 0 / 1mm/step]
7-906-234Middle Speed: # PCU:KENG[0 to 4294967295 / 0 / 1mm/step]
7-906-235Middle Speed: # PCU:CENG[0 to 4294967295 / 0 / 1mm/step]
7-906-236Middle Speed: # PCU:MENG[0 to 4294967295 / 0 / 1mm/step]
7-906-237Middle Speed: # PCU:YENG[0 to 4294967295 / 0 / 1mm/step]




7907[Previous Unit Cntr:Distance(%)]
7-907-002# PCU:KENG[0 to 255 / 0 / 1%/step]
7-907-003# Dev Unit:KENG[0 to 255 / 0 / 1%/step]
7-907-004Developer:KENG[0 to 255 / 0 / 1%/step]
7-907-025# PCU:CENG[0 to 255 / 0 / 1%/step]
7-907-026# Dev Unit:CENG[0 to 255 / 0 / 1%/step]
7-907-027Developer:CENG[0 to 255 / 0 / 1%/step]
7-907-048# PCU:MENG[0 to 255 / 0 / 1%/step]
7-907-049# Dev Unit:MENG[0 to 255 / 0 / 1%/step]
7-907-050Developer:MENG[0 to 255 / 0 / 1%/step]
7-907-071# PCU:YENG[0 to 255 / 0 / 1%/step]
7-907-072# Dev Unit:YENG[0 to 255 / 0 / 1%/step]
7-907-073Developer:YENG[0 to 255 / 0 / 1%/step]
7-907-093# ITB UnitENG[0 to 255 / 0 / 1%/step]
7-907-102# ITB Cleaning UnitENG[0 to 255 / 0 / 1%/step]
7-907-109# PTR UnitENG[0 to 255 / 0 / 1%/step]
7-907-115# Fusing UnitENG[0 to 255 / 0 / 1%/step]
7-907-116Fusing BeltENG[0 to 255 / 0 / 1%/step]
7-907-118Pressure RollerENG[0 to 255 / 0 / 1%/step]
7908[Previous Unit Counter:pages(%)]
7-908-002# PCU:KENG[0 to 255 / 0 / 1%/step]
7-908-003# Dev Unit:KENG[0 to 255 / 0 / 1%/step]
7-908-004Developer:KENG[0 to 255 / 0 / 1%/step]
7-908-025# PCU:CENG[0 to 255 / 0 / 1%/step]
7-908-026# Dev Unit:CENG[0 to 255 / 0 / 1%/step]
7-908-027Developer:CENG[0 to 255 / 0 / 1%/step]
7-908-048# PCU:MENG[0 to 255 / 0 / 1%/step]
7-908-049# Dev Unit:MENG[0 to 255 / 0 / 1%/step]
7-908-050Developer:MENG[0 to 255 / 0 / 1%/step]
7-908-071# PCU:YENG[0 to 255 / 0 / 1%/step]
7-908-072# Dev Unit:YENG[0 to 255 / 0 / 1%/step]
7-908-073Developer:YENG[0 to 255 / 0 / 1%/step]
7-908-093# ITB UnitENG[0 to 255 / 0 / 1%/step]
7-908-102# ITB Cleaning UnitENG[0 to 255 / 0 / 1%/step]
7-908-109# PTR UnitENG[0 to 255 / 0 / 1%/step]
7-908-115# Fusing UnitENG[0 to 255 / 0 / 1%/step]
7-908-116Fusing BeltENG[0 to 255 / 0 / 1%/step]
7-908-118Pressure RollerENG[0 to 255 / 0 / 1%/step]
7-908-131Dust FilterENG[0 to 255 / 0 / 1%/step]
7-908-142Waste Toner BottleENG[0 to 255 / 0 / 1%/step]
7-908-206ADF Pick-up RollerENG[0 to 255 / 0 / 1%/step]
7-908-207ADF Supply BeltENG[0 to 255 / 0 / 1%/step]
7-908-208ADF Reverse RollerENG[0 to 255 / 0 / 1%/step]
Engine SP Mode Tables









7931[Toner Bottle Bk]
7-931-001Machine Serial ID*ENG[0 to 255 / 0 / 1/step]
7-931-002Cartridge Ver*ENG[0 to 255 / 0 / 1/step]
7-931-003Brand ID*ENG[0 to 255 / 0 / 1/step]
7-931-004Area ID*ENG[0 to 255 / 0 / 1/step]
7-931-005Product ID*ENG[0 to 255 / 0 / 1/step]
7-931-006Color ID*ENG[0 to 255 / 0 / 1/step]
7-931-007Maintenance ID*ENG[0 to 255 / 0 / 1/step]
7-931-008New Product Information*ENG[0 to 255 / 0 / 1/step]
7-931-009Recycle Counter*ENG[0 to 255 / 0 / 1/step]
7-931-010Date*ENG[0 to 1 / 0 / 1/step]
7-931-011SerialNo.*ENG[0 to 1 / 0 / 1/step]
7-931-012Toner Remaining*ENG[0 to 100 / 100 / 1%/step]
7-931-013EDP Code*ENG[0 to 1 / 0 / 1/step]
7-931-014End History*ENG[0 to 1 / 0 / 1/step]
7-931-015Refill Information*ENG[0 to 1 / 0 / 1/step]
7-931-016Attachment: Total Counter*ENG[0 to 99999999 / 0 / 1/step]

7-931-017		Attachment: Color Counter
*ENG
[0 to 99999999 / 0 / 1/step]
7-931-018End: Total Counter*ENG[0 to 99999999 / 0 / 1/step]
7-931-019End: Color Counter*ENG[0 to 99999999 / 0 / 1/step]
7-931-020Attachment Date*ENG[0 to 1 / 0 / 1/step]
7-931-021End Date*ENG[0 to 1 / 0 / 1/step]




7932[Toner Bottle M]
7-932-001Machine Serial ID*ENG[0 to 255 / 0 / 1/step]
7-932-002Cartridge Ver*ENG[0 to 255 / 0 / 1/step]
7-932-003Brand ID*ENG[0 to 255 / 0 / 1/step]
7-932-004Area ID*ENG[0 to 255 / 0 / 1/step]
7-932-005Product ID*ENG[0 to 255 / 0 / 1/step]
7-932-006Color ID*ENG[0 to 255 / 0 / 1/step]
7-932-007Maintenance ID*ENG[0 to 255 / 0 / 1/step]
7-932-008New Product Information*ENG[0 to 255 / 0 / 1/step]
7-932-009Recycle Counter*ENG[0 to 255 / 0 / 1/step]
7-932-010Date*ENG[0 to 1 / 0 / 1/step]
7-932-011SerialNo.*ENG[0 to 1 / 0 / 1/step]
7-932-012Toner Remaining*ENG[0 to 100 / 100 / 1%/step]
7-932-013EDP Code*ENG[0 to 1 / 0 / 1/step]
7-932-014End History*ENG[0 to 1 / 0 / 1/step]
7-932-015Refill Information*ENG[0 to 1 / 0 / 1/step]
7-932-016Attachment: Total Counter*ENG[0 to 99999999 / 0 / 1/step]

7-932-017		Attachment: Color Counter
*ENG
[0 to 99999999 / 0 / 1/step]
7-932-018End: Total Counter*ENG[0 to 99999999 / 0 / 1/step]
7-932-019End: Color Counter*ENG[0 to 99999999 / 0 / 1/step]
7-932-020Attachment Date*ENG[0 to 1 / 0 / 1/step]
7-932-021End Date*ENG[0 to 1 / 0 / 1/step]
Engine SP Mode Tables









7933[Toner Bottle C]
7-933-001MachineSerialID*ENG[0 to 255 / 0 / 1/step]
7-933-002Cartridge Ver*ENG[0 to 255 / 0 / 1/step]
7-933-003Brand ID*ENG[0 to 255 / 0 / 1/step]
7-933-004Area ID*ENG[0 to 255 / 0 / 1/step]
7-933-005Product ID*ENG[0 to 255 / 0 / 1/step]
7-933-006Color ID*ENG[0 to 255 / 0 / 1/step]
7-933-007Maintenance ID*ENG[0 to 255 / 0 / 1/step]
7-933-008New Product Information*ENG[0 to 255 / 0 / 1/step]
7-933-009Recycle Counter*ENG[0 to 255 / 0 / 1/step]
7-933-010Date*ENG[0 to 1 / 0 / 1/step]
7-933-011SerialNo.*ENG[0 to 1 / 0 / 1/step]
7-933-012Toner Remaining*ENG[0 to 100 / 100 / 1%/step]
7-933-013EDP Code*ENG[0 to 1 / 0 / 1/step]
7-933-014End History*ENG[0 to 1 / 0 / 1/step]
7-933-015Refill Information*ENG[0 to 1 / 0 / 1/step]
7-933-016Attachment: Total Counter*ENG[0 to 99999999 / 0 / 1/step]

7-933-017		Attachment: Color Counter
*ENG
[0 to 99999999 / 0 / 1/step]
7-933-018End: Total Counter*ENG[0 to 99999999 / 0 / 1/step]
7-933-019End: Color Counter*ENG[0 to 99999999 / 0 / 1/step]
7-933-020Attachment Date*ENG[0 to 1 / 0 / 1/step]
7-933-021End Date*ENG[0 to 1 / 0 / 1/step]




7934[Toner Bottle Y]
7-934-001MachineSerialID*ENG[0 to 255 / 0 / 1/step]
7-934-002Cartridge Ver*ENG[0 to 255 / 0 / 1/step]
7-934-003Brand ID*ENG[0 to 255 / 0 / 1/step]
7-934-004Area ID*ENG[0 to 255 / 0 / 1/step]
7-934-005Product ID*ENG[0 to 255 / 0 / 1/step]
7-934-006Color ID*ENG[0 to 255 / 0 / 1/step]
7-934-007Maintenance ID*ENG[0 to 255 / 0 / 1/step]
7-934-008New Product Information*ENG[0 to 255 / 0 / 1/step]
7-934-009Recycle Counter*ENG[0 to 255 / 0 / 1/step]
7-934-010Date*ENG[0 to 1 / 0 / 1/step]
7-934-011SerialNo.*ENG[0 to 1 / 0 / 1/step]
7-934-012Toner Remaining*ENG[0 to 100 / 100 / 1%/step]
7-934-013EDP Code*ENG[0 to 1 / 0 / 1/step]
7-934-014End History*ENG[0 to 1 / 0 / 1/step]
7-934-015Refill Information*ENG[0 to 1 / 0 / 1/step]
7-934-016Attachment: Total Counter*ENG[0 to 99999999 / 0 / 1/step]

7-934-017		Attachment: Color Counter
*ENG
[0 to 99999999 / 0 / 1/step]
7-934-018End: Total Counter*ENG[0 to 99999999 / 0 / 1/step]
7-934-019End: Color Counter*ENG[0 to 99999999 / 0 / 1/step]
7-934-020Attachment Date*ENG[0 to 1 / 0 / 1/step]
7-934-021End Date*ENG[0 to 1 / 0 / 1/step]
Engine SP Mode Tables









7935[Toner Bottle Log 1: Bk]
7-935-001SerialNo.ENG[0 or 1 / 0 / 1/step]
7-935-002Attachment DateENG[0 or 1 / 0 / 1/step]
7-935-003Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-935-004Refill Information*ENG[0 or 1 / 0 / 1/step]
7935[Toner Bottle Log 2: Bk]
7-935-011SerialNo.ENG[0 or 1 / 0 / 1/step]
7-935-012Attachment DateENG[0 or 1 / 0 / 1/step]
7-935-013Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-935-014Refill Information*ENG[0 or 1 / 0 / 1/step]
7935[Toner Bottle Log 3: Bk]
7-935-021SerialNo.ENG[0 or 1 / 0 / 1/step]
7-935-022Attachment DateENG[0 or 1 / 0 / 1/step]
7-935-023Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-935-024Refill Information*ENG[0 or 1 / 0 / 1/step]
7935[Toner Bottle Log 4: Bk]
7-935-031SerialNo.ENG[0 or 1 / 0 / 1/step]
7-935-032Attachment DateENG[0 or 1 / 0 / 1/step]
7-935-033Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-935-034Refill Information*ENG[0 or 1 / 0 / 1/step]
7935[Toner Bottle Log 5: Bk]
7-935-041SerialNo.ENG[0 or 1 / 0 / 1/step]
7-935-042Attachment DateENG[0 or 1 / 0 / 1/step]
7-935-043Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-935-044Refill Information*ENG[0 or 1 / 0 / 1/step]




7936[Toner Bottle Log 1: M]
7-936-001SerialNo.ENG[0 or 1 / 0 / 1/step]
7-936-002Attachment DateENG[0 or 1 / 0 / 1/step]

7-936-003		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-936-004Refill Information*ENG[0 or 1 / 0 / 1/step]
7936[Toner Bottle Log 2: M]
7-936-011SerialNo.ENG[0 or 1 / 0 / 1/step]
7-936-012Attachment DateENG[0 or 1 / 0 / 1/step]

7-936-013		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-936-014Refill Information*ENG[0 or 1 / 0 / 1/step]
7936[Toner Bottle Log 3: M]
7-936-021SerialNo.ENG[0 or 1 / 0 / 1/step]
7-936-022Attachment DateENG[0 or 1 / 0 / 1/step]

7-936-023		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-936-024Refill Information*ENG[0 or 1 / 0 / 1/step]
7936[Toner Bottle Log 4: M]
7-936-031SerialNo.ENG[0 or 1 / 0 / 1/step]
7-936-032Attachment DateENG[0 or 1 / 0 / 1/step]

7-936-033		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-936-034Refill Information*ENG[0 or 1 / 0 / 1/step]
7936[Toner Bottle Log 5: M]
7-936-041SerialNo.ENG[0 or 1 / 0 / 1/step]
7-936-042Attachment DateENG[0 or 1 / 0 / 1/step]

7-936-043		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-936-044Refill Information*ENG[0 or 1 / 0 / 1/step]
Engine SP Mode Tables









7937[Toner Bottle Log 1: C]
7-937-001SerialNo.ENG[0 or 1 / 0 / 1/step]
7-937-002Attachment DateENG[0 or 1 / 0 / 1/step]

7-937-003		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-937-004Refill Information*ENG[0 or 1 / 0 / 1/step]
7937[Toner Bottle Log 2: C]
7-937-011SerialNo.ENG[0 or 1 / 0 / 1/step]
7-937-012Attachment DateENG[0 or 1 / 0 / 1/step]

7-937-013		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-937-014Refill Information*ENG[0 or 1 / 0 / 1/step]
7937[Toner Bottle Log 3: C]
7-937-021SerialNo.ENG[0 or 1 / 0 / 1/step]
7-937-022Attachment DateENG[0 or 1 / 0 / 1/step]

7-937-023		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-937-024Refill Information*ENG[0 or 1 / 0 / 1/step]
7937[Toner Bottle Log 4: C]
7-937-031SerialNo.ENG[0 or 1 / 0 / 1/step]
7-937-032Attachment DateENG[0 or 1 / 0 / 1/step]

7-937-033		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-937-034Refill Information*ENG[0 or 1 / 0 / 1/step]
7937[Toner Bottle Log 5: C]
7-937-041SerialNo.ENG[0 or 1 / 0 / 1/step]
7-937-042Attachment DateENG[0 or 1 / 0 / 1/step]

7-937-043		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-937-044Refill Information*ENG[0 or 1 / 0 / 1/step]
7938[Toner Bottle Log 1: Y]
7-938-001SerialNo.ENG[0 or 1 / 0 / 1/step]
7-938-002Attachment DateENG[0 or 1 / 0 / 1/step]

7-938-003		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-938-004Refill Information*ENG[0 or 1 / 0 / 1/step]
7938[Toner Bottle Log 2: Y]
7-938-011SerialNo.ENG[0 or 1 / 0 / 1/step]
7-938-012Attachment DateENG[0 or 1 / 0 / 1/step]

7-938-013		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-938-014Refill Information*ENG[0 or 1 / 0 / 1/step]
7938[Toner Bottle Log 3: Y]
7-938-021SerialNo.ENG[0 or 1 / 0 / 1/step]
7-938-022Attachment DateENG[0 or 1 / 0 / 1/step]

7-938-023		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-938-024Refill Information*ENG[0 or 1 / 0 / 1/step]
7938[Toner Bottle Log 4: Y]
7-938-031SerialNo.ENG[0 or 1 / 0 / 1/step]
7-938-032Attachment DateENG[0 or 1 / 0 / 1/step]

7-938-033		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-938-034Refill Information*ENG[0 or 1 / 0 / 1/step]
7938[Toner Bottle Log 5: Y]
7-938-041SerialNo.ENG[0 or 1 / 0 / 1/step]
7-938-042Attachment DateENG[0 or 1 / 0 / 1/step]

7-938-043		Attachment: Total CounterENG[0 to 99999999 / 0 / 1/step]
7-938-044Refill Information*ENG[0 or 1 / 0 / 1/step]
Engine SP Mode Tables





7940[PM Value Setting:Life Distance]
7-940-002# PCU:KENG[0 to 999999999 / 0 / 1mm/step]
7-940-003# Dev Unit:KENG[0 to 999999999 / 0 / 1mm/step]
7-940-004Developer:KENG[0 to 999999999 / 0 / 1mm/step]
7-940-025# PCU:CENG[0 to 999999999 / 0 / 1mm/step]
7-940-026# Dev Unit:CENG[0 to 999999999 / 0 / 1mm/step]
7-940-027Developer:CENG[0 to 999999999 / 0 / 1mm/step]
7-940-048# PCU:MENG[0 to 999999999 / 0 / 1mm/step]
7-940-049# Dev Unit:MENG[0 to 999999999 / 0 / 1mm/step]
7-940-050Developer:MENG[0 to 999999999 / 0 / 1mm/step]
7-940-071# PCU:YENG[0 to 999999999 / 0 / 1mm/step]
7-940-072# Dev Unit:YENG[0 to 999999999 / 0 / 1mm/step]
7-940-073Developer:YENG[0 to 999999999 / 0 / 1mm/step]
7-940-093# ITB UnitENG[0 to 999999999 / 128410397 /
1mm/step]
7-940-102# ITB Cleaning UnitENG[0 to 999999999 / 128410397 /
1mm/step]
7-940-109# PTR UnitENG[0 to 999999999 / 128410397 /
1mm/step]
7-940-115# Fusing UnitENG[0 to 999999999 / 291305000 /
1mm/step]
7-940-116Fusing BeltENG[0 to 999999999 / 291305000 /
1mm/step]
7-940-118Pressure RollerENG[0 to 999999999 / 291305000 /
1mm/step]




7942[PM Counter Display:Distance(%)]
7-942-002# PCU:KENG[0 to 255 / 0 / 1%/step]
7-942-003# Dev Unit:KENG[0 to 255 / 0 / 1%/step]
7-942-004Developer:KENG[0 to 255 / 0 / 1%/step]
7-942-025# PCU:CENG[0 to 255 / 0 / 1%/step]
7-942-026# Dev Unit:CENG[0 to 255 / 0 / 1%/step]
7-942-027Developer:CENG[0 to 255 / 0 / 1%/step]
7-942-048# PCU:MENG[0 to 255 / 0 / 1%/step]
7-942-049# Dev Unit:MENG[0 to 255 / 0 / 1%/step]
7-942-050Developer:MENG[0 to 255 / 0 / 1%/step]
7-942-071# PCU:YENG[0 to 255 / 0 / 1%/step]
7-942-072# Dev Unit:YENG[0 to 255 / 0 / 1%/step]
7-942-073Developer:YENG[0 to 255 / 0 / 1%/step]
7-942-093# ITB UnitENG[0 to 255 / 0 / 1%/step]
7-942-102# ITB Cleaning UnitENG[0 to 255 / 0 / 1%/step]
7-942-109# PTR UnitENG[0 to 255 / 0 / 1%/step]
7-942-115# Fusing UnitENG[0 to 255 / 0 / 1%/step]
7-942-116Fusing BeltENG[0 to 255 / 0 / 1%/step]
7-942-118Pressure RollerENG[0 to 255 / 0 / 1%/step]
Engine SP Mode Tables









7944[PM Counter Display: Distance]
7-944-002# PCU:K*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-003# Dev Unit:K*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-004Developer:K*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-025# PCU:C*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-026# Dev Unit:C*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-027Developer:C*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-048# PCU:M*ENG[0 to 4294967295 / 0 / 1mm/step]
 

Similar threads

J
Ricoh MP C2004/C2504 Service Manual Part 31
Replies
0
Views
57
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 30
Replies
0
Views
40
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 29
Replies
0
Views
39
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 28
Replies
0
Views
47
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 27
Replies
0
Views
43
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 26
Replies
0
Views
44
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 25
Replies
0
Views
73
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 24
Replies
0
Views
49
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 23
Replies
0
Views
46
John
J
Top