Ricoh MP C2004/C2504 Service Manual Part 33

J

John

Member
7-944-049# Dev Unit:M*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-050Developer:M*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-071# PCU:Y*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-072# Dev Unit:Y*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-073Developer:Y*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-093# ITB Unit*ENG[0 to 4294967295 / 0 / 1mm/step]
7-944-102# ITB Cleaning UnitENG[0 to 4294967295 / 0 / 1mm/step]
7-944-109# PTR UnitENG[0 to 4294967295 / 0 / 1mm/step]
7-944-115# Fusing UnitENG[0 to 4294967295 / 0 / 1mm/step]
7-944-116Fusing BeltENG[0 to 4294967295 / 0 / 1mm/step]
7-944-118Pressure RollerENG[0 to 4294967295 / 0 / 1mm/step]
7-944-230Low Speed: # PCU:KENG[0 to 4294967295 / 0 / 1mm/step]
7-944-231Low Speed: # PCU:CENG[0 to 4294967295 / 0 / 1mm/step]
7-944-232Low Speed: # PCU:MENG[0 to 4294967295 / 0 / 1mm/step]
7-944-233Low Speed: # PCU:YENG[0 to 4294967295 / 0 / 1mm/step]
7-944-234Middle Speed: # PCU:KENG[0 to 4294967295 / 0 / 1mm/step]
7-944-235Middle Speed: # PCU:CENG[0 to 4294967295 / 0 / 1mm/step]
7-944-236Middle Speed: # PCU:MENG[0 to 4294967295 / 0 / 1mm/step]
7-944-237Middle Speed: # PCU:YENG[0 to 4294967295 / 0 / 1mm/step]
7950[Unit Replacement Date]
7-950-002# PCU:K*ENG[- / 0 / -]
7-950-003# Dev Unit:K*ENG[- / 0 / -]
7-950-004Developer:K*ENG[- / 0 / -]
7-950-025# PCU:C*ENG[- / 0 / -]
7-950-026# Dev Unit:C*ENG[- / 0 / -]
7-950-027Developer:C*ENG[- / 0 / -]
7-950-048# PCU:M*ENG[- / 0 / -]
7-950-049# Dev Unit:M*ENG[- / 0 / -]
7-950-050Developer:M*ENG[- / 0 / -]
7-950-071# PCU:Y*ENG[- / 0 / -]
7-950-072# Dev Unit:Y*ENG[- / 0 / -]
7-950-073Developer:Y*ENG[- / 0 / -]
7-950-093# ITB Unit*ENG[- / 0 / -]
7-950-102# ITB Cleaning Unit*ENG[- / 0 / -]
7-950-109# PTR Unit*ENG[- / 0 / -]
7-950-115# Fusing Unit*ENG[- / 0 / -]
7-950-116Fusing Belt*ENG[- / 0 / -]
7-950-118Pressure Roller*ENG[- / 0 / -]
7-950-131Dust Filter*ENG[- / 0 / -]
7-950-142Waste Toner Bottle*ENG[- / 0 / -]
7-950-206ADF Pick-up Roller*ENG[- / 0 / -]
7-950-207ADF Supply Belt*ENG[- / 0 / -]
7-950-208ADF Reverse Roller*ENG[- / 0 / -]
Engine SP Mode Tables









7951[Remain Day Counter: Pages]
7-951-002# PCU:KENG[0 to 255 / 255 / 1day/step]
7-951-003# Dev Unit:KENG[0 to 255 / 255 / 1day/step]
7-951-004Developer:KENG[0 to 255 / 255 / 1day/step]
7-951-025# PCU:CENG[0 to 255 / 255 / 1day/step]
7-951-026# Dev Unit:CENG[0 to 255 / 255 / 1day/step]
7-951-027Developer:CENG[0 to 255 / 255 / 1day/step]
7-951-048# PCU:MENG[0 to 255 / 255 / 1day/step]
7-951-049# Dev Unit:MENG[0 to 255 / 255 / 1day/step]
7-951-050Developer:MENG[0 to 255 / 255 / 1day/step]
7-951-071# PCU:YENG[0 to 255 / 255 / 1day/step]
7-951-072# Dev Unit:YENG[0 to 255 / 255 / 1day/step]
7-951-073Developer:YENG[0 to 255 / 255 / 1day/step]
7-951-093# ITB UnitENG[0 to 255 / 255 / 1day/step]
7-951-102# ITB Cleaning UnitENG[0 to 255 / 255 / 1day/step]
7-951-109# PTR UnitENG[0 to 255 / 255 / 1day/step]
7-951-115# Fusing UnitENG[0 to 255 / 255 / 1day/step]
7-951-116Fusing BeltENG[0 to 255 / 255 / 1day/step]
7-951-118Pressure RollerENG[0 to 255 / 255 / 1day/step]
7-951-131Dust FilterENG[0 to 255 / 255 / 1day/step]
7-951-142Waste Toner BottleENG[0 to 255 / 255 / 1day/step]
7-951-206ADF Pick-up RollerENG[0 to 255 / 255 / 1day/step]
7-951-207ADF Supply BeltENG[0 to 255 / 255 / 1day/step]
7-951-208ADF Reverse RollerENG[0 to 255 / 255 / 1day/step]




7952[Remain Day Counter: Distance]
7-952-002# PCU:KENG[0 to 255 / 255 / 1day/step]
7-952-003# Dev Unit:KENG[0 to 255 / 255 / 1day/step]
7-952-004Developer:KENG[0 to 255 / 255 / 1day/step]
7-952-025# PCU:CENG[0 to 255 / 255 / 1day/step]
7-952-026# Dev Unit:CENG[0 to 255 / 255 / 1day/step]
7-952-027Developer:CENG[0 to 255 / 255 / 1day/step]
7-952-048# PCU:MENG[0 to 255 / 255 / 1day/step]
7-952-049# Dev Unit:MENG[0 to 255 / 255 / 1day/step]
7-952-050Developer:MENG[0 to 255 / 255 / 1day/step]
7-952-071# PCU:YENG[0 to 255 / 255 / 1day/step]
7-952-072# Dev Unit:YENG[0 to 255 / 255 / 1day/step]
7-952-073Developer:YENG[0 to 255 / 255 / 1day/step]
7-952-093# ITB UnitENG[0 to 255 / 255 / 1day/step]
7-952-102# ITB Cleaning UnitENG[0 to 255 / 255 / 1day/step]
7-952-109# PTR UnitENG[0 to 255 / 255 / 1day/step]
7-952-115# Fusing UnitENG[0 to 255 / 255 / 1day/step]
7-952-116Fusing BeltENG[0 to 255 / 255 / 1day/step]
7-952-118Pressure RollerENG[0 to 255 / 255 / 1day/step]
Engine SP Mode Tables









7953[Operation Env. Log: PCU: K]
7-953-001T<=0ENG[0 to 999999999 / 0 / 1mm/step]
7-953-0020<T<=5:0<=H<30ENG[0 to 999999999 / 0 / 1mm/step]
7-953-0030<T<=5:30<=H<70ENG[0 to 999999999 / 0 / 1mm/step]
7-953-0040<T<=5:70<=H<=100ENG[0 to 999999999 / 0 / 1mm/step]
7-953-0055<T<15:0<=H<30ENG[0 to 999999999 / 0 / 1mm/step]
7-953-0065<T<15:30<=H<55ENG[0 to 999999999 / 0 / 1mm/step]
7-953-0075<T<15:55<=H<80ENG[0 to 999999999 / 0 / 1mm/step]
7-953-0085<T<15:80<=H<=100ENG[0 to 999999999 / 0 / 1mm/step]
7-953-00915<=T<25:0<=H<30ENG[0 to 999999999 / 0 / 1mm/step]
7-953-01015<=T<25:30<=H<55ENG[0 to 999999999 / 0 / 1mm/step]
7-953-01115<=T<25:55<=H<80ENG[0 to 999999999 / 0 / 1mm/step]
7-953-01215<=T<25:80<=H<=100ENG[0 to 999999999 / 0 / 1mm/step]
7-953-01325<=T<30:0<=H<30ENG[0 to 999999999 / 0 / 1mm/step]
7-953-01425<=T<30:30<=H<55ENG[0 to 999999999 / 0 / 1mm/step]
7-953-01525<=T<30:55<=H<80ENG[0 to 999999999 / 0 / 1mm/step]
7-953-01625<=T<30:80<=H<=100ENG[0 to 999999999 / 0 / 1mm/step]
7-953-01730<=T:0<=H<30ENG[0 to 999999999 / 0 / 1mm/step]
7-953-01830<=T:30<=H<55ENG[0 to 999999999 / 0 / 1mm/step]
7-953-01930<=T:55<=H<80ENG[0 to 999999999 / 0 / 1mm/step]
7-953-02030<=T:80<=H<=100ENG[0 to 999999999 / 0 / 1mm/step]
7-953-02135<=T:0<=H<=100ENG[0 to 999999999 / 0 / 1mm/step]
7953[Operation Env. Log Clear]
7-953-100ENG[0 to 1 / 0 / 1/step]




7954[PM Counter Display: Pages (%)]
7-954-002# PCU:KENG[0 to 255 / 0 / 1%/step]
7-954-003# Dev Unit:KENG[0 to 255 / 0 / 1%/step]
7-954-004Developer:KENG[0 to 255 / 0 / 1%/step]
7-954-025# PCU:CENG[0 to 255 / 0 / 1%/step]
7-954-026# Dev Unit:CENG[0 to 255 / 0 / 1%/step]
7-954-027Developer:CENG[0 to 255 / 0 / 1%/step]
7-954-048# PCU:MENG[0 to 255 / 0 / 1%/step]
7-954-049# Dev Unit:MENG[0 to 255 / 0 / 1%/step]
7-954-050Developer:MENG[0 to 255 / 0 / 1%/step]
7-954-071# PCU:YENG[0 to 255 / 0 / 1%/step]
7-954-072# Dev Unit:YENG[0 to 255 / 0 / 1%/step]
7-954-073Developer:YENG[0 to 255 / 0 / 1%/step]
7-954-093# ITB UnitENG[0 to 255 / 0 / 1%/step]
7-954-102# ITB Cleaning UnitENG[0 to 255 / 0 / 1%/step]
7-954-109# PTR UnitENG[0 to 255 / 0 / 1%/step]
7-954-115# Fusing UnitENG[0 to 255 / 0 / 1%/step]
7-954-116Fusing BeltENG[0 to 255 / 0 / 1%/step]
7-954-118Pressure RollerENG[0 to 255 / 0 / 1%/step]
7-954-131Dust FilterENG[0 to 255 / 0 / 1%/step]
7-954-142Waste Toner BottleENG[0 to 255 / 0 / 1%/step]
7-954-206ADF Pick-up RollerENG[0 to 255 / 0 / 1%/step]
7-954-207ADF Supply BeltENG[0 to 255 / 0 / 1%/step]
7-954-208ADF Reverse RollerENG[0 to 255 / 0 / 1%/step]
Engine SP Mode Tables









7955[Estimated Remain Pages]
7-955-002# PCU:KENG[0 to 9999999 / 0 / 1page/step]
7-955-003# Dev Unit:KENG[0 to 9999999 / 0 / 1page/step]
7-955-004Developer:KENG[0 to 9999999 / 0 / 1page/step]
7-955-025# PCU:CENG[0 to 9999999 / 0 / 1page/step]
7-955-026# Dev Unit:CENG[0 to 9999999 / 0 / 1page/step]
7-955-027Developer:CENG[0 to 9999999 / 0 / 1page/step]
7-955-048# PCU:MENG[0 to 9999999 / 0 / 1page/step]
7-955-049# Dev Unit:MENG[0 to 9999999 / 0 / 1page/step]
7-955-050Developer:MENG[0 to 9999999 / 0 / 1page/step]
7-955-071# PCU:YENG[0 to 9999999 / 0 / 1page/step]
7-955-072# Dev Unit:YENG[0 to 9999999 / 0 / 1page/step]
7-955-073Developer:YENG[0 to 9999999 / 0 / 1page/step]
7-955-093# ITB UnitENG[0 to 9999999 / 0 / 1page/step]
7-955-102# ITB Cleaning UnitENG[0 to 9999999 / 0 / 1page/step]
7-955-109# PTR UnitENG[0 to 9999999 / 0 / 1page/step]
7-955-115# Fusing UnitENG[0 to 9999999 / 0 / 1page/step]
7-955-116Fusing BeltENG[0 to 9999999 / 0 / 1page/step]
7-955-118Pressure RollerENG[0 to 9999999 / 0 / 1page/step]




7956[Estimated Remain Days]
7-956-002# PCU:KENG[0 to 255 / 255 / 1day/step]
7-956-003# Dev Unit:KENG[0 to 255 / 255 / 1day/step]
7-956-004Developer:KENG[0 to 255 / 255 / 1day/step]
7-956-025# PCU:CENG[0 to 255 / 255 / 1day/step]
7-956-026# Dev Unit:CENG[0 to 255 / 255 / 1day/step]
7-956-027Developer:CENG[0 to 255 / 255 / 1day/step]
7-956-048# PCU:MENG[0 to 255 / 255 / 1day/step]
7-956-049# Dev Unit:MENG[0 to 255 / 255 / 1day/step]
7-956-050Developer:MENG[0 to 255 / 255 / 1day/step]
7-956-071# PCU:YENG[0 to 255 / 255 / 1day/step]
7-956-072# Dev Unit:YENG[0 to 255 / 255 / 1day/step]
7-956-073Developer:YENG[0 to 255 / 255 / 1day/step]
7-956-093# ITB UnitENG[0 to 255 / 255 / 1day/step]
7-956-102# ITB Cleaning UnitENG[0 to 255 / 255 / 1day/step]
7-956-109# PTR UnitENG[0 to 255 / 255 / 1day/step]
7-956-115# Fusing UnitENG[0 to 255 / 255 / 1day/step]
7-956-116Fusing BeltENG[0 to 255 / 255 / 1day/step]
7-956-118Pressure RollerENG[0 to 255 / 255 / 1day/step]
7-956-131Dust FilterENG[0 to 255 / 255 / 1day/step]
7-956-142Waste Toner BottleENG[0 to 255 / 255 / 1day/step]
7-956-206ADF Pick-up RollerENG[0 to 255 / 255 / 1day/step]
7-956-207ADF Supply BeltENG[0 to 255 / 255 / 1day/step]
7957[Monthly Average Pages]
7-957-002# PCU:KENG[0 to 9999999 / 0 / 1page/step]
7-957-003# Dev Unit:KENG[0 to 9999999 / 0 / 1page/step]
7-957-004Developer:KENG[0 to 9999999 / 0 / 1page/step]
7-957-025# PCU:CENG[0 to 9999999 / 0 / 1page/step]
7-957-026# Dev Unit:CENG[0 to 9999999 / 0 / 1page/step]
7-957-027Developer:CENG[0 to 9999999 / 0 / 1page/step]
7-957-048# PCU:MENG[0 to 9999999 / 0 / 1page/step]
7-957-049# Dev Unit:MENG[0 to 9999999 / 0 / 1page/step]
7-957-050Developer:MENG[0 to 9999999 / 0 / 1page/step]
7-957-071# PCU:YENG[0 to 9999999 / 0 / 1page/step]
7-957-072# Dev Unit:YENG[0 to 9999999 / 0 / 1page/step]
7-957-073Developer:YENG[0 to 9999999 / 0 / 1page/step]
7-957-093# ITB UnitENG[0 to 9999999 / 0 / 1page/step]
7-957-102# ITB Cleaning UnitENG[0 to 9999999 / 0 / 1page/step]
7-957-109# PTR UnitENG[0 to 9999999 / 0 / 1page/step]
7-957-115# Fusing UnitENG[0 to 9999999 / 0 / 1page/step]
7-957-116Fusing BeltENG[0 to 9999999 / 0 / 1page/step]
7-957-118Pressure RollerENG[0 to 9999999 / 0 / 1page/step]


7-956-208ADF Reverse RollerENG[0 to 255 / 255 / 1day/step]


Engine SP Mode Tables







7958[PM Value Setting:DaysThreshold]
7-958-002# PCU:KENG[1 to 30 / 15 / 1day/step]
7-958-003# Dev Unit:KENG[1 to 30 / 15 / 1day/step]
7-958-004Developer:KENG[1 to 30 / 15 / 1day/step]
7-958-025# PCU:CENG[1 to 30 / 15 / 1day/step]
7-958-026# Dev Unit:CENG[1 to 30 / 15 / 1day/step]
7-958-027Developer:CENG[1 to 30 / 15 / 1day/step]
7-958-048# PCU:MENG[1 to 30 / 15 / 1day/step]
7-958-049# Dev Unit:MENG[1 to 30 / 15 / 1day/step]
7-958-050Developer:MENG[1 to 30 / 15 / 1day/step]
7-958-071# PCU:YENG[1 to 30 / 15 / 1day/step]
7-958-072# Dev Unit:YENG[1 to 30 / 15 / 1day/step]
7-958-073Developer:YENG[1 to 30 / 15 / 1day/step]
7-958-093# ITB UnitENG[1 to 30 / 15 / 1day/step]
7-958-102# ITB Cleaning UnitENG[1 to 30 / 15 / 1day/step]
7-958-109# PTR UnitENG[1 to 30 / 15 / 1day/step]
7-958-115# Fusing UnitENG[1 to 30 / 15 / 1day/step]
7-958-116Fusing BeltENG[1 to 30 / 15 / 1day/step]
7-958-118Pressure RollerENG[1 to 30 / 15 / 1day/step]
7-958-131Dust FilterENG[1 to 30 / 15 / 1day/step]
7-958-142Waste Toner BottleENG[1 to 30 / 15 / 1day/step]
7-958-206ADF Pick-up RollerENG[1 to 30 / 15 / 1day/step]
7-958-207ADF Supply BeltENG[1 to 30 / 15 / 1day/step]
7-958-208ADF Reverse RollerENG[1 to 30 / 15 / 1day/step]




7959[Fusing: Stop]
7-959-001Near End: PageENG[0 to 99999999 / 244000 /
1page/step]
7-959-002End: PageENG[0 to 99999999 / 248000 /
1page/step]
7-959-003Near End: RotationENG[0 to 999999999 / 302229000 /
1mm/step]
7-959-004End: RotationENG[0 to 999999999 / 313153000 /
1mm/step]
Engine SP Mode Tables









7960[Estimated Usage Rate]
7-960-002# PCU:KENG[0 to 255 / 0 / 1%/step]
7-960-003# Dev Unit:KENG[0 to 255 / 0 / 1%/step]
7-960-004Developer:KENG[0 to 255 / 0 / 1%/step]
7-960-025# PCU:CENG[0 to 255 / 0 / 1%/step]
7-960-026# Dev Unit:CENG[0 to 255 / 0 / 1%/step]
7-960-027Developer:CENG[0 to 255 / 0 / 1%/step]
7-960-048# PCU:MENG[0 to 255 / 0 / 1%/step]
7-960-049# Dev Unit:MENG[0 to 255 / 0 / 1%/step]
7-960-050Developer:MENG[0 to 255 / 0 / 1%/step]
7-960-071# PCU:YENG[0 to 255 / 0 / 1%/step]
7-960-072# Dev Unit:YENG[0 to 255 / 0 / 1%/step]
7-960-073Developer:YENG[0 to 255 / 0 / 1%/step]
7-960-093# ITB UnitENG[0 to 255 / 0 / 1%/step]
7-960-102# ITB Cleaning UnitENG[0 to 255 / 0 / 1%/step]
7-960-109# PTR UnitENG[0 to 255 / 0 / 1%/step]
7-960-115# Fusing UnitENG[0 to 255 / 0 / 1%/step]
7-960-116Fusing BeltENG[0 to 255 / 0 / 1%/step]
7-960-118Pressure RollerENG[0 to 255 / 0 / 1%/step]
7-960-131Dust FilterENG[0 to 255 / 0 / 1%/step]
7-960-142Waste Toner BottleENG[0 to 255 / 0 / 1%/step]
7-960-206ADF Pick-up RollerENG[0 to 255 / 0 / 1%/step]
7-960-207ADF Supply BeltENG[0 to 255 / 0 / 1%/step]
7-960-208ADF Reverse RollerENG[0 to 255 / 0 / 1%/step]




7979[ENG Reset Log]
7-979-001Data1*ENG[0x00 to 0xFF / 0x00 / 1/step]
7-979-002Data2*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-003Data3*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-004Data4*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-005Data5*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-006Data6*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-007Data7*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-008Data8*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-009Data9*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-010Data10*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-011Data11*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-012Data12*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-013Data13*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-014Data14*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-015Data15*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-016Data16*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-017Data17*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-018Data18*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-019Data19*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-020Data20*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7-979-021Data21*ENG[0x0000 to 0xFFFF / 0x0000 / 1/step]
7980[Current for Torque Calculation]
7-980-001OPCTransferMotor*ENG[0 to 9.999 / 0 / 0.001A/step]
7-980-002BkDevMotor*ENG[0 to 9.999 / 0 / 0.001A/step]
7-980-003ColorOpcMotor*ENG[0 to 9.999 / 0 / 0.001A/step]
7-980-004ColorDevMotor*ENG[0 to 9.999 / 0 / 0.001A/step]
7-980-005FusingMotor*ENG[0 to 9.999 / 0 / 0.001A/step]
Engine SP Mode Tables









7981[Edict:OffsetValueForTorqCalcu]
7-981-001ManualExeENG[0 or 1 / 0 / 1/step]




7982[OffsetValueForTorqCalculation]
7-982-001OPCTransferMotor*ENG[0 to 655.35 / 0 / 0.01/step]
7-982-002BkDevMotor*ENG[0 to 655.35 / 0 / 0.01/step]
7-982-003ColorOpcMotor*ENG[0 to 655.35 / 0 / 0.01/step]
7-982-004ColorDevMotor*ENG[0 to 655.35 / 0 / 0.01/step]
7-982-005FusingMotor*ENG[0 to 655.35 / 0 / 0.01/step]




7983[OutputLevel1CountNo.]
7-983-001OPCTransferMotor*ENG[0 to 65535 / 0 / 1count/step]
7-983-002BkDevMotor*ENG[0 to 65535 / 0 / 1count/step]
7-983-003ColorOpcMotor*ENG[0 to 65535 / 0 / 1count/step]
7-983-004ColorDevMotor*ENG[0 to 65535 / 0 / 1count/step]
7-983-005FusingMotor*ENG[0 to 65535 / 0 / 1count/step]




7984[OutputLevel2CountNo.]
7-984-001OPCTransferMotor*ENG[0 to 65535 / 0 / 1count/step]
7-984-002BkDevMotor*ENG[0 to 65535 / 0 / 1count/step]
7-984-003ColorOpcMotor*ENG[0 to 65535 / 0 / 1count/step]
7-984-004ColorDevMotor*ENG[0 to 65535 / 0 / 1count/step]
7-984-005FusingMotor*ENG[0 to 65535 / 0 / 1count/step]




7985[OutputLevel3CountNo.]
7-985-001OPCTransferMotor*ENG[0 to 65535 / 0 / 1count/step]
7-985-002BkDevMotor*ENG[0 to 65535 / 0 / 1count/step]
7-985-003ColorOpcMotor*ENG[0 to 65535 / 0 / 1count/step]
7-985-004ColorDevMotor*ENG[0 to 65535 / 0 / 1count/step]
7-985-005FusingMotor*ENG[0 to 65535 / 0 / 1count/step]




7986[VelocityErr.CountNo.]
7-986-001OPCTransferMotor*ENG[0 to 65535 / 0 / 1count/step]
7-986-002BkDevMotor*ENG[0 to 65535 / 0 / 1count/step]
7-986-003ColorOpcMotor*ENG[0 to 65535 / 0 / 1count/step]
7-986-004ColorDevMotor*ENG[0 to 65535 / 0 / 1count/step]
7-986-005FusingMotor*ENG[0 to 65535 / 0 / 1count/step]


Engine SP Mode Tables



  1. INPUT AND OUTPUT CHECK​

    1. INPUT CHECK TABLE​


      Main Machine, Paper Feed Tray​


      5803[INPUT Check]
      5-803-001Registration SensorENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on register sensor position. (0: paper exist, 1: paper non exist)
      5-803-002Paper Feed Sensor 1
      This setting is not available for MP C2004/MP C2504.      		ENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on 1st paper feed sensor position. (0: paper exist, 1: paper non exist)
      5-803-003Transport Sensor 1ENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on 1st carry sensor position. (0: paper exist, 1: paper non exist)
      5-803-004Paper Feed Sensor 2
      This setting is not available for MP C2004/MP C2504.      		ENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on 2nd paper feed sensor position. (0: paper exist, 1: paper non exist)
      5-803-005Transport Sensor 2ENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on 2nd carry sensor position. (0: paper exist, 1: paper non exist)
      5-803-006Fusing Entrance SensorENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on fusing entrance sensor position. (0: paper exist, 1: paper non exist)
      5-803-007Fusing Exit SensorENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on fusing exit sensor position. (0: paper exist, 1: paper non exist)
      5-803-008Paper Exit SensorENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on paper exit sensor position. (0: paper exist, 1: paper non exist)
      5-803-009Inverter SensorENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on reverse sensor position. (0: paper exist, 1: paper non exist)
      5-803-010Duplex Exit SensorENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on duplex exit sensor position. (0: paper exist, 1: paper non exist)
      5-803-011Duplex Entrance SensorENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on duplex entrance sensor position. (0: paper exist, 1: paper non exist)
      5-803-012Tray Full Exit Sensor
      This setting is not available for MP C2004/MP C2504.      		ENG[0 or 1 / 0 / 1/step]
      0: Not full
      1: full
      Detects paper full of main unit paper exit tray. (0: Not full, 1: full)
      5-803-013Tray 1: Paper Height SensorENG[0 to 3 / 0 / 1/step] When full is 100%, 11: 71 to 100%
      01: 31 to 70%
      00: 11 to 30%
      10: 1 to 10%
      Detects remaining paper amount of 1st paper feed tray. (When full is 100%,
      11: 71 to 100%, 01: 31 to 70%, 00: 11 to 30%, 10: 1 to 10%)
      *Check SP5-803-015 for paper end.
      5-803-014Tray 1: Upper Limit SensorENG[0 or 1 / 0 / 1/step] 0: less then limit 1: high then limit
      Detects the height of paper loaded in 1st paper feed tray. (0: less then limit, 1: high then limit)
      * As long as you do not press the white bar of the machine side in the tray back, not output.
      5-803-015Tray 1: Paper End DetectionENG[0 or 1 / 0 / 1/step]
      0: No paper
      1: paper remaining
      Detects paper is running out on 1st paper feed tray. (0: No paper, 1: paper remaining)
      5-803-016Tray 1: Set SensorENG[0 or 1 / 0 / 1/step]
      0: set 1:not set
      Detects that 1st paper feed tray is set to main unit. (0: set, 1:not set)
      Engine SP Mode Tables


      5-803-017Tray 2: Paper Height SensorENG[0 to 3 / 0 / 1/step] When full is 100%, 11: 71 to 100%
      01: 31 to 70%
      00: 11 to 30%
      10: 1 to 10%
      Detects remaining paper amount of 2nd paper feed tray. (When full is 100%,
      11: 71 to 100%, 01: 31 to 70%, 00: 11 to 30%, 10: 1 to 10%)
      *Check SP5-803-019 for paper end.
      5-803-018Tray 2: Paper End SensorENG[0 or 1 / 0 / 1/step] 0: less then limit 1: high then limit
      Detects the height of paper loaded in 2nd paper feed tray. (0: less then limit, 1: high then limit)
      * As long as you do not press the white bar of the machine side in the tray back, not output.
      5-803-019Tray 2: Paper End DetectionENG[0 or 1 / 0 / 1/step]
      0: No paper
      1: paper remaining
      Detects paper running out of 2nd paper feed tray. (0: No paper, 1: paper remaining)
      5-803-020Tray 2: Set SensorENG[0 or 1 / 0 / 1/step]
      0: set
      1: not set
      Detects that 2nd paper feed tray is set to main unit. (0: set, 1:not set)
      5-803-021Tray 2: Size SensorENG[0 to 15 / 0 / 1/step]
      Value changes depending on paper size (fence position) set to 2nd paper feed tray.
      5-803-022By-pass: Paper End SensorENG[0 or 1 / 0 / 1/step]
      0: No paper
      1: paper remaining
      Detects paper is running out on bypass tray. (0: No paper, 1: paper remaining)
      5-803-023By-pass: Main Scan Length SensorENG[0 to 31 / 0 / 1/step]
      Value changes depending on main scan direction of paper set to bypass tray.
      5-803-024By-pass: Sub Scan Length SensorENG[0 or 1 / 0 / 1/step]
      Value changes depending on sub scan direction of paper set to bypass tray.
      5-803-025Interlock Release DetectionENG[0 to 1 / 0 / 1/step]
      00: Unlocked
      11: Locked
      Detects open/close of interlock switch (front cover/right cover). (00: Unlocked, 11: Locked)
      5-803-026Right Door Open/Close SensorENG[0 or 1 / 0 / 1/step]
      0: close
      1: open
      Detects right door status. (0: close, 1: open)
      5-803-027Duplex Guide Plate Open/Close SensorENG[0 or 1 / 0 / 1/step]
      0: close
      1: open
      Detects duplex guide plate status. (0: close, 1: open)
      5-803-028PTR Open/Close SensorENG[0 or 1 / 0 / 1/step]
      0: open
      1: close
      Detects paper transfer unit status. (0: open, 1: close)
      Engine SP Mode Tables


      5-803-029ITB Contact SensorENG[0 or 1 / 0 / 1/step]
      0: Abutting
      1: Alienate
      Detects image transfer roller (Y, M, and C) and photoreceptors distance. (0: Abutting, 1: Alienate)
      5-803-030PTR Contact SensorENG[0 or 1 / 0 / 1/step]
      0: Abutting
      1: Alienate
      Detects image transfer belt and paper transfer rollers distance. (0: Abutting, 1: Alienate)
      5-803-031New ITB Unit DetectionENG[0 or 1 / 0 / 1/step]
      Not available with C1
      5-803-032Toner Collection Full SensorENG[0 or 1 / 0 / 1/step]
      0: Not full
      1: full
      Detects full of waste toner bottle. (0: Not full, 1: full)
      5-803-033Toner Collection Bottle Set SensorENG[0 or 1 / 0 / 1/step]
      0: set
      1: not set
      Detects that waste toner bottle is set to main unit. (0: set, 1:not set)
      5-803-034Toner End Sensor:YENG[0 or 1 / 0 / 1/step]
      0: End
      1: Not End
      Detects remaining toner amount.
      *Power with SP5-804-173 before checking. (0: End, 1: Not End)
      5-803-035Toner End Sensor:MENG[0 or 1 / 0 / 1/step]
      0: End
      1: Not End
      Detects remaining toner amount.
      *Power with SP5-804-173 before checking. (0: End, 1: Not End)
      5-803-036Toner End Sensor:CENG[0 or 1 / 0 / 1/step]
      0: End
      1: Not End
      Detects remaining toner amount.
      *Power with SP5-804-173 before checking. (0: End, 1: Not End)
      5-803-037Toner End Sensor:KENG[0 or 1 / 0 / 1/step]
      0: End
      1: Not End
      Detects remaining toner amount.
      *Power with SP5-804-172 before checking. (0: End, 1: Not End)
      5-803-038Fusing:Area DetectionENG[0 to 15 / 0 / 1/step] 01:200V system 10:100V System 00, 01:unit set error
      Detects region of fusing unit.
      (0111: 200V system, 1011: 100V System)
      5-803-039Fusing:New Unit DetectionENG[0 or 1 / 0 / 1/step]
      0: New
      1: Old
      Detects New/Old of fusing unit. (0: New, 1: Old)
      5-803-040Fusing Temp DetectENG[0 or 1 / 0 / 1/step]
      0: Normal
      1: High temperature
      Detects whether high temperature is detected from fusing unit. (0: Normal, 1: High temperature)
      Engine SP Mode Tables


      5-803-041NC Sensor Temp Detection/ 2ENG[0 or 1 / 0 / 1/step]
      0: Normal
      1: High temperature
      Detects whether high temperature is detected from fusing unit. (0: Normal, 1: High temperature)
      5-803-042NC Sensor Temp Detection/ 1ENG[0 or 1 / 0 / 1/step]
      0: Normal
      1: High temperature
      Detects whether high temperature is detected from fusing unit. (0: Normal, 1: High temperature)
      5-803-047Nip Pres. Release Home Position SensorENG[0 or 1 / 0 / 1/step]
      0: Pressured
      1: Not pressured
      Detects state of fusing nip pressure. (0: Pressured , 1: Not pressured)
      5-803-048Fusing Fan: LockENG[0 or 1 / 0 / 1/step]
      0: Running
      1: Stopped, or locked
      Detects locking of fusing exhaust heat fan. (0: Running, 1: Stopped, or locked)
      5-803-049Dev Fan: Right: LockENG[0 or 1 / 0 / 1/step]
      0: Running
      1: Stopped, or locked
      Detects locking of developer air intake fan (right). (0: Running, 1: Stopped, or locked)
      5-803-051PSU Cooling Fan: LockENG[0 or 1 / 0 / 1/step]
      0: Running
      1: Stopped, or locked
      Detects locking of PSU cooling fan. (0: Running, 1: Stopped, or locked)
      5-803-052Ozone Fan: LockENG[0 or 1 / 0 / 1/step]
      0: Running
      1: Stopped, or locked
      Detects locking of ozone exhaust air fan. (0: Running, 1: Stopped, or locked)
      5-803-054PSU Fan: LockENG[0 or 1 / 0 / 1/step]
      0: Running
      1: Stopped, or locked
      Detects locking of PSU exhaust heat fan. (0: Running, 1: Stopped, or locked)
      5-803-055PCB Box Cooling Fan: LockENG[0 or 1 / 0 / 1/step]
      0: Running
      1: Stopped, or locked
      Detects locking of electric box cooling fan. (0: Running, 1: Stopped, or locked)
      5-803-058Paper Exit Cooling Fan: LockENG[0 or 1 / 0 / 1/step]
      0: Running
      1: Stopped, or locked
      Detects locking of paper exit cooling fan. (0: Running, 1: Stopped, or locked)
      5-803-060Toner Supply Cooling Fan: LockENG[0 or 1 / 0 / 1/step]
      0: Running
      1: Stopped, or locked
      Detects locking of toner supply cooling fan. (0: Running, 1: Stopped, or locked)
      5-803-063Development Motor FC: LockENG[0 or 1 / 0 / 1/step]
      0: Stopped, or locked 1: Running
      Detects locking of developer motor (FC). (0: Running, 1: Stopped, or locked)
      Engine SP Mode Tables


      5-803-064Drum Motor FC: LockENG[0 or 1 / 0 / 1/step]
      0: Stopped, or locked 1: Running
      Detects locking of drum motor (FC). (0: Running, 1: Stopped, or locked)
      5-803-065Fusing Motor: LockENG[0 or 1 / 0 / 1/step]
      0: Stopped, or locked 1: Running
      Detects locking of fusing motor.
      (0: Running, 1: Stopped, or locked)
      5-803-066Transfer Drum Motor K: LockENG[0 or 1 / 0 / 1/step]
      0: Stopped, or locked 1: Running
      Detects locking of transfer drum motor K. (0: Running, 1: Stopped, or locked)
      5-803-068PP:CB:SC DetectionENG[0 or 1 / 0 / 1/step]
      0: SC detected
      1: Normal
      Detects SC of HVP (electrify/develop). (0: SC detected, 1: Normal)
      5-803-069PP:TTS:SC DetectionENG[0 or 1 / 0 / 1/step]
      0: SC detected
      1: Normal
      Detects SC of HVP (transfer). (0: SC detected, 1: Normal)
      5-803-072Key Counter: Set 1ENG[0 or 1 / 0 / 1/step]
      0: set 1:unset
      Detects setting of key counter. (0: set, 1:unset)
      (key counter: set 1=0, 2=1 for set, others for unset)
      5-803-073Key Counter: Set 2ENG[0 or 1 / 0 / 1/step]
      0: unset 1:set
      Detects setting of key counter. (0: unset, 1:set)
      (key counter: set 1=0, 2=1 for set, others for unset)
      5-803-074Key Card SetENG[0 or 1 / 0 / 1/step]
      0: set
      1: not set
      Detects that key card is set to main unit. (0: set, 1:not set)
      5-803-0751 Bin Tray: Paper SensorENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Detects that paper is left upon the tray. (0: paper exist, 1: paper non exist)
      5-803-0761 Bin Tray: Set Detection SystemENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Detects that tray is set to main unit. (0: set, 1:not set)
      5-803-077Bridge Relay SensorENG[0 or 1 / 0 / 1/step]
      0: paper exist
      1: paper non exist
      Responds to paper existence on carry sensor position or bridge unit. (0: paper exist, 1: paper non exist)
      5-803-078Bridge Exit SensorENG[0 or 1 / 0 / 1/step]
      0: Paper exist
      1: Paper do not exist
      Responds to paper existence on paper exit sensor position or bridge unit. (0: paper exist, 1: paper non exist)
      Engine SP Mode Tables


      5-803-079Bridge Set Detection SystemENG[0 or 1 / 0 / 1/step]
      10: set 11:not set
      Detects that bridge unit is set to main unit. (10: set, 11:not set)
      5-803-082Bridge Relay/Left Exit Cover SensorENG[0 or 1 / 0 / 1/step]
      0: close
      1: open
      Detects open/close of the left carry cover open/close sensor (left paper exit tray) and the relay carry cover open/close sensor (bridge unit).
      (0: close, 1: open)
      5-803-083Bridge Exit/Upper Exit Cover SensorENG[0 or 1 / 0 / 1/step]
      0: close
      1: open
      Detects open/close of the upper carry cover open/close sensor (left paper exit tray) and the relay paper exit cover open/close sensor (bridge unit). (0: close, 1: open)
      5-803-084Shift Tray: Set Detection SystemENG[0 or 1 / 0 / 1/step]
      01: set 11:not set
      Detects that shift tray is set to main unit. (01: set, 11:not set)
      5-803-085Shift Tray: Position Sensor 1ENG[0 or 1 / 0 / 1/step]
      0: Stop on this side. during moving towards inner
      1: Stop on inner side. during moving towards this side
      Detects shift tray position.
      (0: Stop on this side. during moving towards inner,
      1: Stop on inner side. during moving towards this side)
      5-803-086Shift Tray: Position Sensor 2ENG[0 or 1 / 0 / 1/step]
      *It is a backup sensor with this machine, so "1" is always displayed)
      5-803-094GAVD Open/Close DetectionENG[0 or 1 / 0 / 1/step]
      For checking door open/close during process. No need to operate.
      5-803-095Bridge 24V Fuse DetectionENG[0 or 1 / 0 / 1/step]
      0: Not cut
      1: Cut
      Detects state of 24V fuse on the bridge unit. (0: Not cut, 1: Cut)
      5-803-096Bridge 5V Fuse DetectionENG[0 or 1 / 0 / 1/step]
      0: Not cut
      1: Cut
      Detects state of 5V fuse on the bridge unit. (0: Not cut, 1: Cut)
      5-803-200HP SensorENG[0 or 1 / 0 / 1/step]
      Tests the scanner HP sensor.
      5-803-201Platen Cover SensorENG[0 or 1 / 0 / 1/step]
      Tests the book open/close sensor.
      5803[INPUT Check]
      Gets information of specified sensor.
      5-803-211Bank: Tray3: Feed SensorENG[0 or 1 / 0 / 1/step]
      0: paper not detected 1: paper detected.
      5-803-212Bank: Tray4: Feed SensorENG
      5-803-213Bank: Tray5: Feed SensorENG
      5-803-214Bank: Tray3: Transport SensorENG
      5-803-215Bank: Tray4: Transport SensorENG
      5-803-216Bank: Tray5: Transport SensorENG
      Engine SP Mode Tables


      5-803-217Bank: Feed Cover Open Detection 1ENG[0 or 1 / 0 / 1/step]
      0: cover open
      1: cover closed
      5-803-218Bank: Feed Cover Open Detection 2ENG
      5-803-219LCT Paper Supply Open/CloseENG
      5-803-220LCT Slide Open/CloseENG[0 or 1 / 0 / 1/step]
      0: slide open
      1: slide closed

      ADF​


      6007[ADF INPUT Check]
      Gets sensor information from ADF. Displays signal level of sensor as it is.
      6-007-001Original Length 1 (B5 Detection Sensor)ENG[0 or 1 / 0 / 1/step]
      6-007-002Original Length 2 (A4 Detection Sensor)ENG[0 or 1 / 0 / 1/step]
      6-007-003Original Length 3 (LG Detection Sensor)ENG[0 or 1 / 0 / 1/step]
      6-007-004Original Width 1ENG[0 or 1 / 0 / 1/step]
      6-007-005Original Width 2ENG[0 or 1 / 0 / 1/step]
      6-007-006Original Width 3ENG[0 or 1 / 0 / 1/step]
      6-007-007Original Width 4ENG[0 or 1 / 0 / 1/step]
      6-007-008Original Width 5ENG[0 or 1 / 0 / 1/step]
      6-007-009Original DetectionENG[0 or 1 / 0 / 1/step]
      6-007-011Skew CorrectionENG[0 or 1 / 0 / 1/step]
      6-007-013Registration SensorENG[0 or 1 / 0 / 1/step]
      6-007-014Exit SensorENG[0 or 1 / 0 / 1/step]
      6-007-015Feed Cover SensorENG[0 or 1 / 0 / 1/step]
      6-007-016Lift Up SensorENG[0 or 1 / 0 / 1/step]
      6-007-023Rear Edge DetectionENG[0 or 1 / 0 / 1/step]
      Engine SP Mode Tables




      6011[1-Pass ADF INPUT Check]
      For Single-Pass simultaneous duplex models only.
      6-011-001Original Length 1 (B5 Sensor)ENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-002Original Length 2 (A4 Sensor)ENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-003Original Length 3 (LG Sensor)ENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-004Original Width 1ENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-005Original Width 2ENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-006Original Width 3ENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-007Original Width 4ENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-008Original Width 5ENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-009Original DetectionENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when original is set.
      6-011-010Separation SensorENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-011Skew CorrectionENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-012Scan Entrance SensorENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-013Registration SensorENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-014Exit SensorENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
      6-011-015Feed Cover SensorENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when cover is open.
      6-011-016Lift Up SensorENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when lift up.
      6-011-018Pick-Up Roller HP SensorENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when pick up roller is not in home position.
      6-011-021Bottom Plate HP SensorENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when bottom plate is not in home position.
      6-011-022Bottom Plate Position SensorENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when pick up roller is not in the correct position.
      6-011-023Original Length 4 (LT/A4 Tail Sensor)ENG[0 or 1 / 0 / 1/step]
      Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.


      Engine SP Mode Tables

      Finisher​


      6123[INPUT Check: 2K/3K FIN]
      6-123-001Entrance SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-002Horizontal Transport SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-003Switchback Transport SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-004Proof Tray Exit SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-005Shift Tray Exit SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-006Booklet Stapler Exit SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-007Paper Exit Open/Close Guide HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-008Punch HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-009Punch Move HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-010S-to-S Registration Detection HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-011Lower Junction Solenoid HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-012Jogger HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-013Positioning Roller HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-014Feed-out HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-015Stapler Moving HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-016Booklet Stapler HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-017Booklet Jogger HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-018Booklet Jog Solenoid HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-019Booklet Standard Fence HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-020Booklet Stapler HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-022Folder Blade Cam HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-023Folder Blade HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-024Shift Roller HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-028Drag Roller Vibrating HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-029LE Guide HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-030TE Stack Plate HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-031Staple Tray Paper SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-032ITB Paper SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      Engine SP Mode Tables


      6-123-033Booklet Stapler Transport Paper Sn: UpperENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-034Booklet Stapler Transport Paper Sn: LowerENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-035Paper Height Sensor: ShiftENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-036Corner Stapler Paper Height Sensor 1ENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-037Corner Stapler Paper Height Sensor 2ENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-038Proof Tray Full SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-039Booklet Stapler Full Sensor 1ENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-040Booklet Stapler Full Sensor 2ENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-041S-to-S Registration Detection SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-042Punch RPS SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-043Corner Stapler Leading Edge Detection SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-044Corner Stapler Staple End SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-045Booklet Stapler Staple End Sensor: FrontENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-046Booklet Stapler Staple End Sensor: RearENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-047Shift Tray Lower Limit Sensor 1ENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-048Shift Tray Lower Limit Sensor 2ENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-049Shift Tray Lower Limit Sensor 3ENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-050Shift Tray Lower Limit Sensor 4ENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-051Shift Tray Lower Limit Sensor 5ENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-052Punch Chad Full SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-123-053Punch Set DetectionENG[0 or 1 / 0 / 1/step]
      0: connected
      1: not connected
      Engine SP Mode Tables


      Gets connection status of punch unit.
      6-123-054Shift Jogger Set DetectionENG[0 or 1 / 0 / 1/step]
      0: connected
      1: not connected
      Gets connection status of setting jogger unit.
      * Not use: currently, VOLGA-B does not have setting jogger in system configuration.
      6-123-055Booklet Stapler Set DetectionENG[0 or 1 / 0 / 1/step]
      0: not connected
      1: connected
      Gets connection status of saddle stitch unit.
      6-123-056Front Door SWENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-123-057Dynamic Roller Open/Close Guide Plate SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-123-058Tray Upper Limit SWENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-123-059Paper Exit Open/Close Guide Plate Limit SWENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-123-060Punch Selection DIPSW 1ENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-123-061Punch Selection DIPSW 2ENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-123-065Paper Guide HP SensorENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-123-066Shift Jogger HP Sensor: FrontENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-123-067Shift Jogger HP Sensor: RearENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-123-068Shift Jogger Retraction HP Sensor: UpperENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-123-069Shift Jogger Retraction HP Sensor: LowerENG[0 or 1 / 0 / 1/step]
      Gets information of specified switch. Displays signal level of switch as it is.
      Engine SP Mode Tables




      6135[INPUT Check: FrontFIN]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-135-001Entrance Sensor*ENG[0 or 1 / 0 / 1/step]
      6-135-002Carry Sensor*ENG[0 or 1 / 0 / 1/step]
      6-135-003Exit Sensor*ENG[0 or 1 / 0 / 1/step]
      6-135-004Staple Tray Paper Sensor*ENG[0 or 1 / 0 / 1/step]
      6-135-005Front Jogger HP Sensor*ENG[0 or 1 / 0 / 1/step]
      6-135-006Rear Jogger HP Sensor*ENG[0 or 1 / 0 / 1/step]
      6-135-007Sft Roller HP Sensor*ENG[0 or 1 / 0 / 1/step]
      6-135-008Hitroll HP Sensor*ENG[0 or 1 / 0 / 1/step]
      6-135-009Ext Guide Plate HP Sensor*ENG[0 or 1 / 0 / 1/step]
      6-135-010Staple Moving HP SensorENG[0 or 1 / 0 / 1/step]
      6-135-011Shift Tray Paper SensorENG[0 or 1 / 0 / 1/step]
      6-135-012Shift Tray Limit SensorENG[0 or 1 / 0 / 1/step]
      6-135-013Staple Rotation SensorENG[0 or 1 / 0 / 1/step]
      6-135-014Staple Near End SensorENG[0 or 1 / 0 / 1/step]
      6-135-015Self Priming SensorENG[0 or 1 / 0 / 1/step]
      6-135-016Stopper HP SensorENG[0 or 1 / 0 / 1/step]
      6-135-017Punch HP SensorENG[0 or 1 / 0 / 1/step]
      6-135-018Punch Pluse Count SensorENG[0 or 1 / 0 / 1/step]
      6-135-019Punch Chad Full SensorENG[0 or 1 / 0 / 1/step]
      6-135-020Punch Moving HP SensorENG[0 or 1 / 0 / 1/step]
      6-135-021Punch Registration Detection HP SensorENG[0 or 1 / 0 / 1/step]
      6-135-022Punch Registration Detection SensorENG[0 or 1 / 0 / 1/step]
      6135[INPUT Check: FrontFIN]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-135-023Slide Door SWENG[0 or 1 / 0 / 1/step]
      6-135-024Shift Tray Upper Limit SWENG[0 or 1 / 0 / 1/step]


      6161[FIN (1K FIN) INPUT Check]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-161-001Entrance SensorENG[0 or 1 / 0 / 1/step]
      6-161-002Upper Cover Open/Close SensorENG[0 or 1 / 0 / 1/step]
      6-161-003Proof Tray Exit SensorENG[0 or 1 / 0 / 1/step]
      6-161-004Proof Tray Full SensorENG[0 or 1 / 0 / 1/step]
      6-161-005Shift HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-006Exit Guide Plate Open/Close HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-007Shift Paper Exit (Lift Tray Exit) SensorENG[0 or 1 / 0 / 1/step]
      6-161-008Positioning Roller HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-009Lift Tray Paper SensorENG[0 or 1 / 0 / 1/step]
      6-161-010Jogger HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-011Feed Out HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-012Lift Tray Lower Limit Sensor (Upper)ENG[0 or 1 / 0 / 1/step]
      6-161-013Lift Tray Lower Limit Sensor (Lower)ENG[0 or 1 / 0 / 1/step]
      6-161-014Staple Tray Paper SensorENG[0 or 1 / 0 / 1/step]
      6-161-015Stapler Moving HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-016Near End Sensor (Common: Corner/Bklt Stplr)ENG[0 or 1 / 0 / 1/step]
      6-161-017Self Priming Sensor (Common:Crnr/Bklt Stplr)ENG[0 or 1 / 0 / 1/step]
      6-161-018Driver HP Sensor (Corner/Booklet Stapler)ENG[0 or 1 / 0 / 1/step]
      6-161-020Clincher HP Sensor (Corner/Booklet Stapler)ENG[0 or 1 / 0 / 1/step]
      6-161-022Stapler Retraction SensorENG[0 or 1 / 0 / 1/step]
      6-161-023UntitledENG[0 or 1 / 0 / 1/step]
      6-161-024UntitledENG[0 or 1 / 0 / 1/step]
      6-161-025UntitledENG[0 or 1 / 0 / 1/step]
      6-161-026Punch HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-027Punch RP SensorENG[0 or 1 / 0 / 1/step]
      6-161-028Punch Hopper Full SensorENG[0 or 1 / 0 / 1/step]
      6-161-029Punch Move HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-030S-to-S Registration Detection HP SensorENG[0 or 1 / 0 / 1/step]
      Engine SP Mode Tables


      6-161-031S-to-S Registration Detection SensorENG[0 or 1 / 0 / 1/step]
      6161[FIN (1K FIN) INPUT Check]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-161-032Punch Selection DIPSW 1ENG[0 or 1 / 0 / 1/step]
      6-161-033Punch Selection DIPSW 2ENG[0 or 1 / 0 / 1/step]
      6161[FIN (1K FIN) INPUT Check]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-161-034ITB Transport Sensor: RightENG[0 or 1 / 0 / 1/step]
      6-161-035ITB Transport Sensor: LeftENG[0 or 1 / 0 / 1/step]
      6-161-036Stack Transport SensorENG[0 or 1 / 0 / 1/step]
      6-161-037Stack Trans Upper Pressure Release HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-038Stack Trans Lower Pressure Release HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-039Fold Blade HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-040Fold Cam HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-041TE Stopper Transport SensorENG[0 or 1 / 0 / 1/step]
      6-161-042TE Stopper HP SensorENG[0 or 1 / 0 / 1/step]
      6-161-043Booklet Folder Exit SensorENG[0 or 1 / 0 / 1/step]
      6-161-044Booklet Folder Tray Full Sensor: UpperENG[0 or 1 / 0 / 1/step]
      6-161-045Booklet Folder Tray Full Sensor: LowerENG[0 or 1 / 0 / 1/step]
      6161[FIN (1K FIN) INPUT Check]
      Gets information of specified switch. Displays signal level of switch as it is.
      6-161-046Door Open/Close SWENG[0 or 1 / 0 / 1/step]
      6-161-047Lift Tray Upper Limit SWENG[0 or 1 / 0 / 1/step]
      6161[FIN (1K FIN) INPUT Check]
      Gets information of specified sensor. Displays signal level of sensor as it is.
      6-161-048Paper Guide HP SensorENG[0 or 1 / 0 / 1/step]
      Engine SP Mode Tables




      6184[Input Check: NoStplBindFIN]
      6-184-001Entrance SensorENG[0 or 1 / 0 / 1/step]
      Gets the entrance sensor information of non staple finisher. (0: Sensor Off, 1: Sensor On)
      6-184-002Exit SensorENG[0 or 1 / 0 / 1/step]
      Gets the paper exit sensor information of non staple finisher. (0: Sensor Off, 1: Sensor On)
      6-184-003Horizontal Registration Detection SensorENG[0 or 1 / 0 / 1/step]
      Gets the horizontal registration sensor information of non staple finisher. (0: Sensor Off, 1: Sensor On)
      6-184-004Shift HP SensorENG[0 or 1 / 0 / 1/step]
      Gets the shift HP sensor information of non staple finisher. (0: Sensor Off, 1: Sensor On)
      6-184-005Junction Solenoid HP SensorENG[0 or 1 / 0 / 1/step]
      Gets the junction solenoid HP sensor information of non staple finisher. (0: Sensor Off, 1: Sensor On, “0“ appears if sensor detects home position)
      6-184-006Exit Pressure Release HP SensorENG[0 or 1 / 0 / 1/step]
      Gets the exit pressure release HP sensor information of non staple finisher. (0: Sensor Off, 1: Sensor On)
      6-184-007Stapler HP SensorENG[0 or 1 / 0 / 1/step]
      Gets the stapler HP sensor information of non staple finisher. (0: Sensor On, “0“ appears if sensor detects home position)
      6-184-008Tray Full Detection Sensor 1ENG[0 or 1 / 0 / 1/step]
      Gets the tray full detection sensor 1 information of non staple finisher. (0: Paper overflow )
      6-184-009Tray Full Detection Sensor 2ENG[0 or 1 / 0 / 1/step]
      Gets the tray full detection sensor 2 information of non staple finisher. (0: Paper overflow )
      6-184-010Slide Door Open/Close Door SWENG[0 or 1 / 0 / 1/step]
      Gets the slide door switch information of non staple finisher. (0: Close, 1: Open)

    2. OUTPUT CHECK TABLE​



Main Machine, Paper Feed Tray​



5804[OUTPUT Check]
5-804-001Feed Pickup Solenoid 1 This setting is not available for
MP C2004/MP C2504.		ENG[0 or 1 / 0 / 1/step]
Moves 1st paper feed tray pick up solenoid.
5-804-002Feed Pickup Solenoid 2 This setting is not available for
MP C2004/MP C2504.		ENG[0 or 1 / 0 / 1/step]
Moves 2nd paper feed tray pick up solenoid.
5-804-003Bypass Pickup SolenoidENG[0 or 1 / 0 / 1/step]
Moves bypass pick up solenoid.
5-804-004Exit Junction SolenoidENG[0 or 1 / 0 / 1/step]
Moves output paper divide solenoid.
5804[OUTPUT Check]
Moves paper feed tray rising motor.
* Do not execute SP 5-804-006/008 without removing the paper tray. Otherwise, the tray might be damaged.
5-804-005Tray 1 Lift Motor:CWENG[0 or 1 / 0 / 1/step]
5-804-006Tray 1 Lift Motor:CCWENG
5-804-007Tray 2 Lift Motor:CWENG
5-804-008Tray 2 Lift Motor:CCWENG
5804[OUTPUT Check]
Moves register motor.
5-804-009Regist Motor:CCW:Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-011Regist Motor:CCW:Low SpeedENG
5804[OUTPUT Check]
5-804-015Regist Motor:position HoldENG[0 or 1 / 0 / 1/step]
Holds position of register motor.
5804[OUTPUT Check]
Moves paper feed motor.
* It is fed if there is paper in the paper tray.
5-804-016Feed Motor:CW:Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-018Feed Motor:CW:Low SpeedENG
5-804-022Feed Motor:CCW:Standard SpeedENG
5-804-024Feed Motor:CCW:Low SpeedENG
Engine SP Mode Tables





5804[OUTPUT Check]
Moves transport motor.
5-804-028Bypass V-Transport Motor:CW:Std SpeedENG[0 or 1 / 0 / 1/step]
5-804-030Bypass V-Transport Motor:CW:Low SpeedENG
5804[OUTPUT Check]
5-804-034Bypass V-Transport Motor:position HoldENG[0 or 1 / 0 / 1/step]
Holds position of transport motor.
5-804-037Exit Motor: CW: Fusing Pressure ReleaseENG[0 or 1 / 0 / 1/step]
Moves fusing dis-pressure.
* If driving this motor while attaching the fusing unit, be sure to stop it less than 5 seconds. Otherwise, the unit might be damaged.
5804[OUTPUT Check]
Moves paper exit motor.
5-804-041Exit Motor:CCW:Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-043Exit Motor:CCW:Low SpeedENG
5804[OUTPUT Check]
Moves reverse motor.
5-804-047Inverter Motor:CW:Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-049Inverter Motor:CW:Low SpeedENG
5-804-052Inverter Mt: CW: Normal Speed: DuplexENG
5-804-054Inverter Mt: CW: Low Speed: DuplexENG
5-804-056Inverter Motor:CCW:Standard SpeedENG
5-804-058Inverter Motor:CCW:Low SpeedENG
5-804-061Inverter Mt: CCW: Normal Speed: Inc SpeedENG
5804[OUTPUT Check]
Moves duplex entrance motor.
5-804-065Duplex Entrance Motor:CW:Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-067Duplex Entrance Motor:CW:Low SpeedENG
5-804-068Duplex Entrance Motor: Normal Speed: DuplexENG
5-804-069Duplex Entrance Motor: Low Speed: DuplexENG
5804[OUTPUT Check]
Moves bypass/duplex motor.
5-804-071Duplex Bypass Motor:CW:Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-073Duplex Bypass Motor:CW:Low SpeedENG
5-804-074Duplex Bypass Motor: CW: Normal Speed: DupENG
5-804-075Duplex Bypass Motor: CW: Low Speed: DuplexENG
Engine SP Mode Tables





5-804-077Duplex Bypass Motor:CCW:Standard SpeedENG
5-804-079Duplex Bypass Motor:CCW:Low SpeedENG
5804[OUTPUT Check]
5-804-083Duplex Bypass Motor:position HoldENG[0 or 1 / 0 / 1/step]
Holds position of bypass/duplex motor.
5804[OUTPUT Check]
Moves fusing motor. *See Important below
5-804-092Fusing Motor:CW:Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-094Fusing Motor:CW:Low SpeedENG
5-804-098Fusing Motor:CCW:Low SpeedENG
Important: Use the procedure below to do the output checks for the fusing exit motor. If you do not follow this procedure, a kink will form in the fusing belt sleeve, and the fusing sleeve belt unit will need to be replaced.
1. Do one of the following:
  • Open the right cover of the paper bank
  • Remove one of the toner bottles
  • Pull out the waste toner bottle half-way
  • Remove the fusing unit
  1. Enter SP mode.
  2. Do the following out output checks:
  • SP5-804-092 (Fusing Motor:CW:Standard Speed)
  • SP5-804-094 (Fusing Motor:CW:Low Speed)
  • SP5-804-098 (Fusing Motor:CCW:Low Speed)
  1. Without exiting SP mode, turn the main power switch off and then on again. Important: If you exit SP mode before you turn the main power switch off, the fusing exit motor will stay off when the machine warms up. Heat will be concentrated in one area of the fusing belt sleeve and cause a kink to form. If this happens, you will need to replace the fusing sleeve belt unit.
  2. Do the reverse of what you did in step 1 (for example, reattach the fusing unit).
5804[OUTPUT Check]
5-804-104Polygon Motor: LENG[0 or 1 / 0 / 1/step]
Runs motor with 21969 rpm.
5-804-105Polygon Motor: MENG[0 or 1 / 0 / 1/step]
Runs motor with 25512 rpm.
5-804-106Polygon Motor: HENG[0 or 1 / 0 / 1/step]
Runs motor with 30236 rpm.
5-804-107Polygon Motor: HHENG[0 or 1 / 0 / 1/step]
Runs motor with 34488 rpm.
5-804-110Fusing Fan: Full SpeedENG[0 or 1 / 0 / 1/step]
Moves fusing exhaust fan.
5-804-111Fusing Fan: Half SpeedENG[0 or 1 / 0 / 1/step]
Moves fusing exhaust fan.
Engine SP Mode Tables





5-804-113PSU Cooling/Exhaust Heat FanENG[0 or 1 / 0 / 1/step]
Moves PSU cooling fan and PSU exhaust fan (not included in this machine).
5-804-114Ozone FanENG[0 or 1 / 0 / 1/step]
Moves ozone exhaust heat fan.
5-804-115PCB Box Cooling Fan/ Exhaust Cooling FanENG[0 or 1 / 0 / 1/step]
Moves controller box cooling fan and exhaust cooling fan.
5-804-116Development: Right: Half SpeedENG[0 or 1 / 0 / 1/step]
Moves development intake fan.
5-804-117Drive Cooling/ Main/ Toner Supply Cooling FanENG[0 or 1 / 0 / 1/step]
Moves drive cooling fan (not included in this machine), main exhaust fan (not included in this machine), and toner supply cooling fan.
5-804-118Development: RightENG[0 or 1 / 0 / 1/step]
Moves development intake fan.
5-804-119Development SolenoidENG[0 or 1 / 0 / 1/step]
Moves development solenoid.
5804[OUTPUT Check]
Moves development motor.
5-804-128Development Motor FC: Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-130Development Motor FC: Low SpeedENG
5804[OUTPUT Check]
Moves/Stops PCU motor :CMY.
* Execute this SP after correcting the cam position so that ITB contact/separation lever of the color station is released.
5-804-132Drum Motor FC: Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-134Drum Motor FC: Low SpeedENG
5804[OUTPUT Check]
Moves/Stops PCU motor: Black/ ITB drive motor.
* Execute this SP after correcting the cam position so that ITB contact/separation lever of the color station is released.
5-804-136Transfer Drum Motor K: Standard SpeedENG[0 or 1 / 0 / 1/step]
5-804-138Transfer Drum Motor K: Low SpeedENG
5804[OUTPUT Check]
Moves paper transfer contact and release motor.
5-804-140PTR Contact Motor:CWENG[0 or 1 / 0 / 1/step]
5-804-141PTR Contact Motor:CCWENG
5804[OUTPUT Check]
Moves ITB contact and release motor (reverse to toner supply motor M).
* Execute this SP after correcting the cam position so that ITB contact/separation lever of the color station is released.
5-804-150Toner Supply Motor M:CW:(ITB Contact)ENG[0 or 1 / 0 / 1/step]
5804[OUTPUT Check]
Moves relay carry motor (bridge unit)/left paper exit carry motor (left paper exit tray).
5-804-163Bridge Relay/Left Exit Motor: Normal SpeedENG[0 or 1 / 0 / 1/step]
Engine SP Mode Tables





5-804-165Bridge Relay/Left Exit Motor: Low SpeedENG
5-804-166Bridge Relay/Left Ex Mt: Normal Speed UpperENG
5804[OUTPUT Check]
5-804-169Bridge Junction/Left Exit Junction SolenoidENG[0 or 1 / 0 / 1/step]
Moves relay divide solenoid (bridge unit)/left paper exit divide solenoid (left paper exit tray).
5-804-170Shift Tray Motor:CWENG[0 or 1 / 0 / 1/step]
Moves shift tray motor.
5-804-171Shift Tray Motor:CCWENG[0 or 1 / 0 / 1/step]
Moves shift tray motor.
5-804-172Toner End Sensor: K PowerENG[0 or 1 / 0 / 1/step]
Supples power to toner end sensor (K).
5-804-173Toner End Sensor: FC PowerENG[0 or 1 / 0 / 1/step]
Supples power to toner end sensor (FC).
5-804-174Drum PCL: KENG[0 or 1 / 0 / 1/step]
Lights (PWM drive) the drum PCL (K).
* Continuing the OPC's exposure, it might accumulate damage due to electrostatic locally.
  • If operating QL without rotation, be sure to stop it within 10 seconds.
  • Do rotate the OPC drum when QL is turned on.
5-804-175Drum PCL: FCENG[0 or 1 / 0 / 1/step]
Lights (PWM drive) the drum PCL (FC).
* Continuing the OPC's exposure, it might accumulate damage due to electrostatic locally.
  • If operating QL without rotation, be sure to stop it within 10 seconds.
  • Do rotate the OPC drum when QL is turned on.
5804[OUTPUT Check]
Outputs PWM for electrify HVP (DC/AC:Y/M/C/K).
5-804-176PP: Charge DC: YENG[0 or 1 / 0 / 1/step]
5-804-177PP: Charge DC: MENG
5-804-178PP: Charge DC: CENG
5-804-179PP: Charge DC: KENG
5-804-180PP: Charge AC: YENG
[0 or 1 / 0 / 1/step]
This setting is not available for MP C2004/MP C2504
5-804-181PP: Charge AC: MENG
5-804-182PP: Charge AC: CENG
5-804-183PP: Charge AC: KENG
5804[OUTPUT Check]
Outputs PWM for develop HVP.
5-804-184PP: Development: YENG[0 or 1 / 0 / 1/step]
5-804-185PP: Development: MENG
5-804-186PP: Development: CENG
5-804-187PP: Development: KENG
5804[OUTPUT Check]
Outputs PWM for transfer HVP (image transfer: Y/M/C/K).
5-804-195PP: ITB: YENG[0 or 1 / 0 / 1/step]
5-804-196PP: ITB: MENG
5-804-197PP: ITB: CENG
5-804-198PP: ITB: KENG
5804[OUTPUT Check]
Outputs PWM for transfer HVP (paper transfer: +/-).
5-804-199PP: PTR: +ENG[0 or 1 / 0 / 1/step]
5-804-200PP: PTR: -ENG
Engine SP Mode Tables
 

Similar threads

J
Ricoh MP C2004/C2504 Service Manual Part 34
Replies
0
Views
16
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 32
Replies
0
Views
52
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 31
Replies
0
Views
76
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 30
Replies
0
Views
52
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 29
Replies
0
Views
54
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 28
Replies
0
Views
60
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 27
Replies
0
Views
59
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 26
Replies
0
Views
57
John
J
J
Ricoh MP C2004/C2504 Service Manual Part 25
Replies
0
Views
82
John
J
Top