Switch 00

FUNCTION AND COMMENTS

ITU-T T1 time (for PSTN G3 mode)

If the connection time to a particular terminal is longer than the NCU parameter setting, adjust this byte. The T1 time is the value stored in this byte (in hex code), multiplied by 1 second.

Range:

0 to 120 s (00h to 78h)

FFh - The local NCU parameter factory setting is used. Do not program a value between 79h and FEh.

Switch 01

No

FUNCTION

COMMENTS

0-4

TX level

If communication with a particular remote terminal often contains errors, the signal level may be inappropriate. Adjust the TX level for communications with that terminal until the results are better.

If the setting is "Disabled", the NCU parameter 01 setting is used.

 Do not use settings other than listed on the left.

Bit4

Bit3

Bit2

Bit1

Bit0

0

0

0

0

0

0

0

0

0

0

1

–1

0

0

0

1

0

–2

0

0

0

1

1

–3

0

0

1

0

0

–4

0

1

1

1

1

–15

1

1

1

1

1

Disabled

5-7

Cable equalizer

Bit 7: 0, Bit 6: 0, Bit 5: 0 = None

Bit 7: 0, Bit 6: 0, Bit 5: 1 = Low

Bit 7: 0, Bit 6: 1, Bit 5: 0 = Medium

Bit 7: 0, Bit 6: 1, Bit 5: 1 = High

Bit 7: 1, Bit 6: 1, Bit 5: 1 = Disabled

Use a higher setting if there is signal loss at higher frequencies because of the length of wire between the modem and the telephone exchange when calling the number stored in this Quick/Speed Dial.

Also, try using the cable equalizer if one or more of the following symptoms occurs.

Communication error with error codes such as 0-20, 0-23, etc. Modem rate fallback occurs frequently.

 Do not use settings other than listed on the left.

If the setting is "Disabled", the bit switch setting is used.

Switch 02

No

FUNCTION

COMMENTS

0-3

Initial TX modem rate

If training with a particular remote terminal always takes too long, the initial modem rate may be too high. Reduce the initial TX modem rate using these bits.

For the settings 14.4 or kbps slower, Switch 04 bit 4 must be changed to 0.

 Do not use settings other than listed on the left. If the setting is "Disabled", the bit switch setting is used.

Bit3

Bit2

Bit1

Bit0

bps

0

0

0

0

Not used

0

0

0

1

2400

0

0

1

0

4800

0

0

1

1

7200

0

1

0

0

9600

0

1

0

1

12000

0

1

1

0

14400

0

1

1

1

16800

1

0

0

0

19200

1

0

0

1

21600

1

0

1

0

24000

1

0

1

1

26400

1

1

0

0

28800

1

1

0

1

31200

1

1

1

0

33600

1

1

1

1

Disabled

Other settings: Not used

4-7

Not used

Do not change the settings.

Switch 03

No

FUNCTION

COMMENTS

0-1

Inch-mm conversion before

If "inch only" is selected on the machine uses

TX

inch-based resolutions for scanning, the printed

Bit 1: 0, Bit 0: 0

copy may be slightly distorted at the other end if

= Inch-mm conversion

that machine uses mm-based resolutions.

available

If the setting is "Inch-mm conversion available ",

Bit 1: 0, Bit 0: 1 = Inch only

Inch-mm conversion become effective to the

Bit 1: 1, Bit 0: 0 = Not used

special senders.

Bit 1: 1, Bit 0: 1 = Disabled

If the setting is "Disabled", the bit switch setting is

used.

2-3

DIS/NSF detection method

(0, 1): Use this setting if echoes on the line are

Bit 3: 0, Bit 2: 0

interfering with the set-up protocol at the start of

= First DIS or NSF

transmission. The machine will then wait for the

Bit 3: 0, Bit 2: 1

second DIS or NSF before sending DCS or NSS.

= Second DIS or NSF

If the setting is "Disabled", the bit switch setting is

Bit 3: 1, Bit 2: 0 = Not used

used.

Bit 3: 1, Bit 2: 1 = Disabled

4

V.8 protocol 0: Off

1: Disabled

If transmissions to a specific destination always end at a lower modem rate (14,400 bps or lower), disable V.8 protocol so as not to use V.34 protocol. 0: V.34 communication will not be possible.

If the setting is "Disabled", the bit switch setting is used.

5

Compression modes available in transmit mode

0: MH only

1: Disabled

This bit determines the capabilities that are informed to the other terminal during transmission. If the setting is "Disabled", the bit switch setting is used.

6-7

ECM during transmission Bit 7: 0, Bit 6: 0 = Off

Bit 7: 0, Bit 6: 1 = On

Bit 7: 1, Bit 6: 0 = Not used

Bit 7: 1, Bit 6: 1 = Disabled

For example, if ECM is switched on but is not wanted when sending to a particular terminal, use the (0, 0) setting.

 V.8/V.34 protocol and JBIG compression are automatically disabled if ECM is disabled.

 If the setting is "Disabled", the bit switch setting is used.

Switch 04 - Not used (do not change the settings)

Switch 05 - Not used (do not change the settings)

Switch 06 - Not used (do not change the settings)

Switch 07 - Not used (do not change the settings)

Switch 08 - Not used (do not change the settings)

Switch 09 - Not used (do not change the settings)

Switch 00

No

FUNCTION

COMMENTS

0

MH Compression mode

Switches MH compression on and off for files

for e-mail attachments

attached to e-mails for sending.

0: Off

1: On

1

MR Compression mode

Switches MR compression on and off for files

for e-mail attachments

attached to e-mails for sending.

0: Off

1: On

2

MMR Compression mode

Switches MMR compression on and off for files

for e-mail attachments

attached to e-mails for sending.

0: Off

1: On

3-6

Not used

Do not change these settings.

7

Designates the bits to

The "0" selection (default) references the settings for

reference for

Bits 00, 01, 02 above. The "1" selection ignores the

compression method of

selections of Bits 00, 01, 02.

e-mail attachments

0: Registered (Bit 0 to 6)

1: No registration.

Switch 01

No

FUNCTION

COMMENTS

0

Original width of e-mail

Sets the original width of the e-mail attachment as

attachment: A4

A4.

0: Off

1: On

1

Original width of e-mail

Sets the original width of the e-mail attachment as

attachment: B4

B4.

0: Off

1: On

2

Original width of e-mail

Sets the original width of the e-mail attachment as

attachment: A3

A3.

0: Off

1: On

3-6

Not used

Do not change these settings.

7

Designates the bits to

The "0" selection (default) references the settings for

reference for original size

Bits 00, 01, 02 above. The "1" selection ignores the

of e-mail attachments

selections of Bits 00, 01, 02.

0: Registered (Bit 0 to 6)

1: No registration.

Switch 02

No

FUNCTION

COMMENTS

0

Line resolution of e-mail

Sets the line resolution of the e-mail attachment as

attachment: 200 x 100

200 x100.

0: Off

1: On

1

Line resolution of e-mail

Sets the line resolution of the e-mail attachment as

attachment: 200 x 200

200 x 200.

0: Off

1: On

2

Line resolution of e-mail

Sets the line resolution of the e-mail attachment as

attachment: 200 x 400

200 x 400.

0: Off

1: On

3

Not used

Do not change these settings.

4

Line resolution of e-mail

Sets the line resolution of the e-mail attachment as

attachment: 400 x 400

400 x 400.

0: Off

1: On

5-6

Not used

Do not change these settings.

7

Designates the bits to

The "0" selection (default) references the settings for

reference for original size

Bits 00, 01, 02, 04 above. The "1" selection ignores

of e-mail attachments

the selections of Bits 00, 01, 02, 04.

0: Registered (Bit 0 to 6)

1: No registration.

Switch 03 - Not used (do not change the settings)

Switch 04

No

FUNCTION

COMMENTS

0

Full mode address selection

0: Full mode address 1: No full mode (simple mode)

If the other ends have the addresses, which have the full mode function flag ("0"), this machine determines them as full mode standard machines.

 This machine attaches the "demand of reception confirmation" to a message when transmitting.

 This machine updates the reception capability to the address book when receiving.

1-7

Not used

Do not change these settings.

Switch 05

No

FUNCTION

COMMENTS

0

Directr transmission

Allows or does not allow the direct transmission to

selection to SMTP server

SMTP server.

0: ON

1: OFF

1-7

Not used

Do not change these settings.

Switch 06 - Not used (do not change the settings)

Switch 07 - Not used (do not change the settings)

Switch 08 - Not used (do not change the settings)

Switch 09 - Not used (do not change the settings)