6006*

ADF Registration Adjust

Adjusts the side-to-side and leading edge registration for simplex and duplex original feeding in ARDF mode.

SP6006-5 sets the maximum setting allowed for rear edge erase.

001

Side-to-Side Regist: Front

[–3 to 3 / 0 / 0.1 mm / step]

002

Side-to-Side Regist: Rear

003

Leading Edge Registration

[–5 to 5 / 0 / 0.1 mm / step]

005

Buckle: Duplex Front

[–3 to 3 / 0 / 0.1 mm / step]

006

Buckle: Duplex Rear

[–2.5 to 2.5 / 0 / 0.1 mm / step]

007

Rear Edge Erase

[–10 to 10 / 0 / 0.1 mm / step]

6007

ADF Input Check

001

Original Length 1 (B5 Detection Sensor)

0: Paper not detected 1: Paper detected

002

Original Length 2 (A4 Detection Sensor)

003

Original Length 3 (LG Detection Sensor)

004

Original Width Sensor 1

005

Original Width Sensor 2

006

Original Width Sensor 3

007

Original Width Sensor 4

008

Original Width Sensor 5

009

Original Set Sensor

010

Separation Sensor

011

Skew Correction Sensor

012

Scan Entrance Sensor

013

Registration Sensor

014

Exit Sensor

015

Feed Cover Sensor

0: ADF cover closed 1: ADF cover open

016

Lift Up Sensor

0: ADF closed

1: ADF open

017

Inverter Sensor

0: Paper not detected 1: Paper detected

018

Pick-up Roller HP Sensor

0: HP (Pick-up roller: Up)

1: Not HP (Pick-up roller: Down)

019

Original Set HP Sensor

0: HP (Stopper: UP)

1: Not HP (Stopper: Down)

6008

ADF Output Check

001

Pick-up Motor Forward

002

Pick-up Motor Reserve

003

Feed Motor Forward

004

Feed Motor Reserve

005

Relay Motor Forward

007

Inverter Motor Forward

008

Inverter Motor Reserve

011

Inverter Solenoid

012

Stamp

013

Fan Motor

6009

ADF FreeRun

Performs an ARDF free run in duplex mode. Press [ON] to start, press [OFF] to stop.

Note: This is a general free run controlled from the copier.

001

Free Run: Simplex Motion

002

Free Run: Duplex Motion

003

Free Run: Stamp Motion

6010*

ADF Stamp Position Adjust.

[–5 to 5 / 0 / 0.1 mm step]

Adjusts the horizontal position of the stamp on the scanned originals.

6016*

Original Size Detect Setting

Specifies the original size for a size detected by the original sensor, since original sensors cannot recognize all sizes.

(7) 0000 0000 (0)

Different bits are used for detection, depending on the location as shown below.

Bit

Size

Location

7

A4 (L)/LT (L)

Japan only

6

11" x 15"/DLT (L)

5

DLT (L)/ 11" x 15"

NA only

4

LT (S)/ US Exec (S)

3

LT (L)/ 8" x 10" (L)

2

LG (L)/ F4 (L)

1

A4 (L)/ 16K (L)

EU/AA only

0

8K (L)/ DLT (L)

6017*

DF Magnification Adj.

[–5 to 5 / 0 / 0.1% step]

Adjusts the magnification in the sub-scan direction for ADF mode. Use the key to toggle between + and - before entering the value

6020*

Skew Correction Moving Setting

Turns the original skew correction in the ARDF for all original sizes on or off. [0 to 1 / 0 / 1 ]

0: Off (only for small original sizes) 1: On (for all original sizes)

6128

Punch Position: Sub Scan

Adjusts the punching position in the sub scan direction. (For D636/D637)

001

2-Hole: DOM (Japan)

[-7.5 to 7.5 / 0 / 0.5 mm]

002

3-Hole: NA

003

4-Hole: EU

004

5-Hole: SCAN

005

2-Hole: NA

6129

Punch Position: Main Scan

Adjusts the punching position in the main scan direction. (For D636/D637)

001

2-Hole: DOM (Japan)

[-2 to 2 / 0 / 0.4 mm]

002

3-Hole: NA

003

4-Hole: EU

004

4-Hole: SCAN

005

2-Hole: NA

6130*

Skew Correction: Buckle Adj.

Adjusts the paper buckle at the punch unit for each paper size. (For D636/D637)

001

A3 SEF

[-5 to 5 / 0 / 0.25 mm]

002

B4 SEF

003

A4 SEF

004

A4 LEF

005

B5 SEF

006

B5 LEF

007

DLT SEF

008

LG SEF

009

LT SEF

010

LT LEF

011

12" x 18"

012

Other

6131*

Skew Correction Control

Selects the skew correction control for each paper size. (For D636/D637)

001

A3 SEF

[0 to 1 / 1 / 1 mm]

002

B4 SEF

003

A4 SEF

004

A4 LEF

005

B5 SEF

006

B5 LEF

007

DLT SEF

008

LG SEF

009

LT SEF

010

LT LEF

011

12" x 18"

012

Other

6132*

Jogger Fence Fine Adj.

This SP adjusts the distance between the jogger fences and the sides of the stack on the finisher stapling tray in the (Booklet) Finisher D636/D637. The adjustment is done perpendicular to the direction of paper feed.

001

A3 SEF

[-1.5 to 1.5 / 0 / 0.5 mm]

002

B4 SEF

003

A4 SEF

004

A4 LEF

005

B5 SEF

006

B5 LEF

007

DLT SEF

008

LG SEF

009

LT SEF

010

LT LEF

011

12" x 18"

012

Other

6133*

Staple Position Adjustment

Adjusts the staple position for each finisher (D636/D637).

+ Value: Moves the staple position to the rear side.

- Value: Moves the staple position to the front side. [-3.5 to 3.5 / 0 / 0.5 mm]

6134*

Saddle Stitch Position Adj.

Use this SP to adjust the stapling position of the booklet stapler when paper is stapled and folded in the Booklet Finisher (D637).

001

A3 SEF

[-3 to 3 / 0 / 0.2 mm]

+ Value: Shifts staple position toward the crease.

- Value: Shifts staple position away from the crease

002

B4 SEF

003

A4 SEF

004

B5 SEF

005

DLT SEF

006

LG SEF

007

LT SEF

008

12" x 18"

009

Other

6135*

Folder Position Adj.

This SP corrects the folding position when paper is stapled and folded in the Booklet Finisher D637.

001

A3 SEF

[-3 to 3 / 0 / 0.2 mm]

+ Value: Shifts staple position toward the crease.

- Value: Shifts staple position away from the crease.

002

B4 SEF

003

A4 SEF

004

B5 SEF

005

DLT SEF

006

LG SEF

007

LT SEF

008

12" x 18"

009

Other

6136*

Book Fold Repeat

Sets the number of times that folding is done in the Booklet Finisher D637. [2 to 30 / 2 / 1 time/step]

6137

Finisher Free Run

These SPs are used for the D588 or D636/D637.

001

Free Run 1

D588: System free run

D636/D637: Free run for paper edge stapling.

002

Free Run 2

D588: Free run for durability testing D636/D637: Not used

003

Free Run 3

Not used

004

Free Run 4

Not used

6139

Entrance Sensor

Display the signals received from sensors and switches of the (booklet) finisher. (D588) p.3-251 "Input Check")

6140

FIN (EUP) INPUT Check

Display the signals received from sensors and switches of the (booklet) finisher. (D636/D637) p.3-251 "Input Check")

6144

FIN (KIN) OUPUT Check

Display the signals received from sensors and switches of the (booklet) finisher. (D588) p.3-263 "Output Check")

6145

FIN (EUP) OUPUT Check

Display the signals received from sensors and switches of the (booklet) finisher. (D636/D637) p.3-263 "Output Check")

6149*

Max. Pre-Stack Sheet

[0 to 3 / 3 / 1 sheets step]

This SP sets the number of sheets sent to the pre-stack tray.

 You may need to adjust this setting or switch it off when feeding thick or slick paper.

6800

Sheet Conversion (Thick Paper)

Permits punching, including tab sheets. Note: Do not change this setting.

[1 to 3 / 3 / 1 sheet]

1: 1 Sheet

2: 2 Sheets

3: 3 Sheets

6830*

Extra Staples

More than the standard number of sheets can be stapled. This SP sets the additional number of sheets (This Setting + Standard Number = maximum number of sheets).

 If the number of the maximum for staples is increased, and the mechanical warranty of the unit can be guaranteed, then the setting can take effect without changing the controller software.

 However, assurance that mechanical performance can be guaranteed is required before changing the setting to increase the staple load for more than the maximum in the feed/exit specifications. Raising this setting without quality assurance could damage the machine.

1

Staple positions other than booklet stapling

[0 to 50 / 0 /1]

2

2 Booklet stapling

[0 to 50 / 0 /1]

6910

Shading Control

001

ON/OFF

[0 to 1 / 0 / 1 ]

0= OFF, 1= ON

Enables or disables the shading adjustment for DF mode.

002

Shading Interval: A

[0 to 60 / 3 / 1 sec] DFU

003

Shading Interval: B

[0 to 120 / 60 / 1 ] DFU