5024*

mm/inch Display Selection

0: Europe/Asia (mm) 1: North America (inch)

Selects the unit of measurement.

After selection, turn the main power switch off and on.

5045*

Accounting counter

Selects whether the printer counter is displayed on the LCD. [0-1 / 0 / 1]

0: Displays the total counter only.

1: Displays both total counter and printer counter.

5047*

Paper Display

Turns on or off the printed paper display on the LCD. [0 to 1 / 0 / 1]

0: Not displayed, 1: Displayed

5052*

ReturnTimePriorityType

Select the priority to return to the stand-by mode. [0 to 1 / 0 / 1]

0: Energy Save has priority 1: Return time has priority

5055*

Display IP Address

Display or does not display the IP address on the LCD. [0 to 1 / 0 / 1]

0: OFF, 1: ON

5056*

Coverage Counter Display

Display or does not display the coverage counter on the LCD. [0 to 1 / 0 / 1]

0: Not displayed, 1: Displayed

5061*

Toner Remaining Icon Display Change

Display or does not display the remaining toner display icon on the LCD. [0 to 1 / 0 / 1 ]

0: Not display, 1: Display

5062

Parts Replacement Alert Display

Display or does not display the parts replacement alert on the LCD.

001

PCU_Bk

[0 to 1 / 0 / 1 ]

0: Not displayed, 1: Display

002

Fuser

[0 to 1 / 0 / 1 ]

0: Not displayed, 1: Display

003

Transfer Unit [0 to 1 / 0 / 1 ]

0: Not displayed, 1: Display

004

FuserCleaner [0 to 1 / 0 / 1 ]

0: Not displayed, 1: Display

5071

Set Bypass Paper Size Display

001

Turn on or off the paper size confirmation pop-up on the LED. This pop-up prevents mismatching between a paper size selected by the operation panel and the actual paper size on the by-pass tray.

[0 or 1 / 0 / -]

0: Off, 1: On

5074*

Home Screen Login

Sets the application that appears when the home key is pressed.

002

Setting

[0 to 11111111 / 0 / 1]

0: OFF, 1: ON

091

Home Key Customization

[0 to 2 / 0 / 1 ]

0: OFF (Function disable), 1: SDK, 2: Reserve (Legacy application)

092

Product ID

Sets the Application product ID. [0x00 to 0xffff / 0x00 / 1]

093

Application Screen ID

Sets the display category of the application that is specified in the SP5075-001.

[0 to 255 / 0 / 1 ]

5075*

USB Keyboard

001

Function Setting

[0 to 1 / 0 / 1 ]

0: Disable, 1: Enable

5083

[LED Light Switch Setting - Toner Near End]

001

Choose whether or not the [Check Status] key blinks when Toner Near End is reached.

NOTE: (Requires System/Copy Firmware 2.05 of later)

[0 to 1 / 0 / 1 ] - This SP makes it possible to set whether or not the [Check Status] key blinks when Toner Near End is reached.

[0: Does not blink/ 1: Blinks] - With previous firmware versions, this key always blinked

when Toner Near End was reached.

5083

[LED Light Switch Setting - Toner Near End]

001

Choose whether or not the [Check Status] key blinks when Toner Near End is reached.

NOTE: (Requires System/Copy Firmware 2.05 of later)

[0 to 1 / 0 / 1 ] - This SP makes it possible to set whether or not the [Check Status] key blinks when Toner Near End is reached.

[0: Does not blink/ 1: Blinks] - With previous firmware versions, this key always blinked

when Toner Near End was reached.

5083

[LED Light Switch Setting - Toner Near End]

001

Choose whether or not the [Check Status] key blinks when Toner Near End is reached.

NOTE: (Requires System/Copy Firmware 2.05 of later)

[0 to 1 / 0 / 1 ] - This SP makes it possible to set whether or not the [Check Status] key blinks when Toner Near End is reached.

[0: Does not blink/ 1: Blinks] - With previous firmware versions, this key always blinked

when Toner Near End was reached.

5104*

A3/DLT Double Count (SSP)

001

When "Yes" is selected, A3 and DLT paper are counted twice, that is A4 x2 and LT x2 respectively.

[0 to 1 / 1 / 1 ]

[0: Single Count/ 1: Double Count (Default)] NOTE: (Requires System/Copy Firmware

2.06 of later) for default = 1.

5104*

A3/DLT Double Count (SSP)

001

When "Yes" is selected, A3 and DLT paper are counted twice, that is A4 x2 and LT x2 respectively.

[0 to 1 / 1 / 1 ]

[0: Single Count/ 1: Double Count (Default)] NOTE: (Requires System/Copy Firmware

2.06 of later) for default = 1.

5104*

A3/DLT Double Count (SSP)

001

When "Yes" is selected, A3 and DLT paper are counted twice, that is A4 x2 and LT x2 respectively.

[0 to 1 / 1 / 1 ]

[0: Single Count/ 1: Double Count (Default)] NOTE: (Requires System/Copy Firmware

2.06 of later) for default = 1.

5113*

Optional Counter Type

001

Default Optional Counter Type

Selects the type of counter:

0: None

1: Key Card (RK3, 4) Japan only 2: Key Card Down

3: Pre-paid Card

4: Coin Rack

5: MF Key Card

11: Exp. Key Card (Add) 12: Exp. Key Card (Deduct)

002

External Optional Counter Type

Enables the SDK application. This lets you select a number for the external device for user access control.

Note: "SDK" refers to software on an SD card. [0 to 3 / 0 / 1]

0: None

1: Expansion Device 1

2: Expansion Device 2

3: Expansion Device 3

5114*

Optional Counter I/F

001

MF Key Card Extension

Use this SP and change the setting to "1" only when the "5" (MF Key Card) is selected with SP5113-001.

[0: Not installed/ 1: Installed (scanning accounting)]

5118*

Disable Copying

Temporarily denies access to the machine. Japan Only [0 to 1 / 0 / 1]

0: Release for normal operation [Default] 1: Prohibit access to machine

5120*

Mode Clear Opt. Counter Removal

Selects if mode clear is done for an optional counter when an optional counter is removed.

0: Yes. (Always mode clear)

1: StandBy. (Mode clear before/after a job) 2: No. (No mode clear)

5121*

Counter Up Timing

Determines whether the optional key counter counts up at paper feed-in or at paper exit.

[0 to 1 / 0 / 1 ]

0: Feed, 1: Exit

5126*

F Size Original Setting

Selects F size original setting. [0 to 2 / 0 / 1 step]

0: 8 1/2 x 13 (Foolscap)

1: 8 1/4 x 13 (Folio)

2: 8 x 13 (F)

5127*

APS Mode

Selects whether the APS function is enabled or disabled with the contact of a pre-paid card or coin lock.

0: Disable (APS active) [Default], 1: Enable (APS not active)

5131*

Paper Size Type Selection

Selects the paper size (type) for both originals and copy paper. [0 to 2 / - / 1 step]

0: Japan, 1: North America, 2: Europe

After changing the setting, turn the copier off and on. If the paper size of the archive files stored on the HDD is different, abnormal copies could result.

5150

Bypass Length Setting

Sets up the by-pass tray for long paper. [0 to 1 / 0 / 1]

0: Off [Default]

1: On. Sets the tray for feeding paper up to 600 mm long.

With this SP selected on, paper jams are not detected in the paper path.

5162*

App. Switch Method

Determines whether the application screen is switched with a hardware switch or software switch.

0: Soft Key Set 1: Hard Key Set

5165*

Z-Fold Position

Not Used

5166*

Lump Delete Form Setting

021

Last Deleted Time

Displays the last delete time. [0 to 4294967295 / 0 / 1]

5167*

Fax Printing Mode at Optional Counter Off

Enables or disables the automatic print out without an accounting device. This SP is used when the receiving fax is accounted for by an external accounting device.

0: Automatic printing

1: No automatic printing

5169*

CE Login

If you will change the printer bit switches, you must 'log in' to service mode with this SP before you go into the printer SP mode.

[0 to 1 / 0 / 1]

0: Off. Printer bit switches cannot be adjusted. 1: On. Printer bit switches can be adjusted.

5179*

By-pass Tray Paper Size Error

[0 to 1 / 0 / 1 ] 0= OFF, 1= ON

This SP determines whether a paper size error prompt appears when the machine detects the wrong paper size for the job and during feed from the by-pass tray.

5181*

Paper Size Setting

Adjusts the paper size for each tray. [0 to 1 / - / 1]

001

Tray 1: 1

0: A4 LEF, 1: LT LEF

002

Tray 1: 2

0: A3, 1: DLT

003

Tray 1: 3

0: B4, 1: LG

004

Tray 1: 4

0: B5 LEF, 1: Exe LEF

005

Tray 2: 1

0: A4 LEF, 1: LT LEF

006

Tray 2: 2

0: A3, 1: DLT

007

Tray 2: 3

0: B4, 1: LG

008

Tray 2: 4

0: B5 LEF, 1: Exe LEF

009

Tray 3: 1 (Tandem)

0: A4 LEF, 1: LT LEF

010

Tray 3: 2

0: A3, 1: DLT

011

Tray 3: 3

0: B4, 1: LG

012

Tray 3: 4

0: B5 LEF, 1: Exe LEF

013

Tray 4: 1

0: A4 LEF, 1: LT LEF

014

Tray 4: 2

0: A3, 1: DLT

015

Tray 4: 3

0: B4, 1: LG

016

Tray 4: 4

0: B5 LEF, 1: Exe LEF

017

LCT

[0 to 2 / - / 1 ] 0: A4 LEF, 1: LT LEF, 2: B5 LEF

5186

RK4: Setting (Japan only)

Enable or distance the prevention for RK4 (Accounting device) Disconnection. If the RK4 is disconnected for 10 seconds when this SP is set to "1 (Enable)", the machine automatically jams a sheet of paper and stops.

[0 to 1 / 0 / 1]

5188*

Copy Nv Version

Displays the NV version on the controller.

5193

External Controller Info. Settings

DFU

5195*

Limitless SW

DFU

5199

Paper Exit After Staple End

This SP determines whether the machine can output paper if staple supply runs out.

[0 to 1 / 0 / 1]

0: OFF. Paper cannot exit if no staples are available. 1: ON. Paper can exit with no staples.

5212*

Page Numbering

003

Duplex Printout Left/Right Position

Horizontally positions the page numbers printed on both sides during duplexing. [–10 to 10/ 0 / 1 mm]

0 is center, minus is left, + is right.

004

Duplex Printout High/Low Position

Vertically positions the page numbers printed on both sides during duplexing.

[–10 to 10/ 0 / 1 mm]

0 is center, minus is down, + is up.

5227*

Page Numbering

201

Allow Page No. Entry

Sets the number of input digits for the job serial number of the starting page numbering. [2 to 9 / 9 / 1]

202

Zero Surplus Setting

Sets the zero surplus serial number of the starting page numbering.

[0 to 1 / 0 / 1]

0: Disable, 1: Enable

5302*

Set Time

002

Time Difference

Sets the time clock for the local time. This setting is done at the factory before delivery. The setting is GMT expressed in minutes.

[–1440 to 1440 / - / 1 min.]

Japan: +540 (Tokyo)

NA: -300 (NY)

EU: +60 (Paris)

CH: +480 (Peking)

TW: +480 (Taipei)

AS: +480 (Hong Kong) KO: +540 (Korea)

5307

Summer Time

001

Setting

[0 to 1 / 1 (NA/EU), 0 (ASIA) / 1 /step]

0: Disabled

1: Enabled

Enables or disables the summer time mode.

 Make sure that both SP5-307-3 and -4 are correctly set. Otherwise, this SP is not activated even if this SP is set to "1".

003

Rule Set (Start)

Specifies the start setting for the summer time mode.

There are 8 digits in this SP. For months 1 to 9, the "0" cannot be input in the first digit, so the eight-digit setting for -2 or -3 becomes a seven-digit setting. 1st and 2nd digits: The month. [1 to 12]

3rd digit: The week of the month. [1 to 5]

4th digit: The day of the week. [0 to 6 = Sunday to Saturday] 5th and 6th digits: The hour. [00 to 23]

7th digit: The length of the advanced time. [0 to 9 / 1 hour /step] 8th digit: The length of the advanced time. [0 to 5 / 10 minutes /step] For example: 3500010

The timer is advanced by 1 hour at am 0:00 on the 5th Sunday in March. The digits are counted from the left.

Make sure that SP5-307-1 is set to "1".

004

Rule Set (End)

Specifies the end setting for the summer time mode. There are 8 digits in this SP.

1st and 2nd digits: The month. [1 to 12] 3rd digit: The week of the month. [0 to 5]

4th digit: The day of the week. [0 to 7 = Sunday to Saturday] 5th and 6th digits: The hour. [00 to 23]

The 7th and 8 digits must be set to "00". The digits are counted from the left.

Make sure that SP5-307-1 is set to "1".

5401*

Access Control (DFU)

This SP stores the settings that limit uses access to SDK application data.

103

Default Document ACL

Whenever a new login user is added to the address book in external certification mode (for Windows, LDAP, RDH), the default document ACL is updated according to this SP setting.

[0 to 3 / 0 / 1]

0: View

1: Edit

2: Edit/Delete

3: Full control

Note: This SP setting is ignored on a machine that is not using document server.

104

Authentication Time

Specifies the timeout of the authentication.

[0 to 255 / 0 / 1 sec./step]

0: 60 seconds

1 to 250 seconds

162

Extend Certification Detail

Selects the log out type for the extend authentication device.

Bit 0: Log-out without an IC card 0: Not allowed (default)

1: Allowed

200

SDK1 Unique ID

"SDK" is the "Software Development Kit". This data can be converted from SAS (VAS) when installed or uninstalled. (DFU)

201

SDK1 Certification Method

210

SDK2 Unique ID

211

SDK2 Certification Method

220

SDK3 Unique ID

221

SDK3 Certification Method

230

SDK certification device

240

Detail Option

Enables or disables the log out confirmation option.

Bit 0: Log out confirmation option 0: Enable (default), 1: Disable Selects the automatic log out time. Bit 1 and 2: Automatic log out timer reduction

00: 60 seconds (default), 01: 10 seconds,

10: 20 seconds, 11: 30 seconds

5402

Access Control (DFU)

Sets limited uses for SDKJ application data.

101 to 130

SDKJ1 Limit Setting….. SDKJ30 Limit Setting

141 to 170

SDKJ1 Product ID….. SDKJ30 Product ID

5404

User Code Count Clear

Clears the counts of the user codes assigned by the key operator to restrict the use of the machine. Press [Execute] to clear.

5411*

LDAP-Certification

004

Simplified Certification

Turns simple authentication on or off for LDAP. [0 to 1 / 1 / 1]

0: OFF

1: ON

005

Password Null Not Permit

This SP is enabled only when SP5411-4 is set to "1" (ON).

[0 to 1 / 1 / 1]

0: Password null is permitted.

1: Password null is not permitted.

006

Detail Option

Determines whether LDAP option (anonymous certification) is turned on or off.

[0 to 11111111 / 0 / 1]

0: OFF, 1: ON

5412

Krb-Certification

100

Encrypt Mode

Sets the level of Kerberos Certification. [0x01:AES256-CTS-HMAC-SHA1-96 / 0x02:AES128-CTS-HMAC-SHA1-96 /

0x04:DES3-CBC-SHA / 0x08:RC4-HMAC /

0x10:DES-CBC-MD5 / 0xFF:ALL / 0xFF / 1bit]

5413

Lockout Setting

001

Lockout On/Off

[0 to 1 / 0 / 1] 0: OFF, 1:ON

Turns on or off the account lock for the local address book account.

002

Lockout Threshold

[1 to 10 / 5 / 1]

Sets the maximum trial times for accessing the address book account.

003

Cancellation On/Off

[0 to 1 / 0 / 1]

0: OFF (Lockout is not cancelled.)

1: ON (Lockout is cancelled if a user ID and password are correctly entered after the lockout function has been executed and a specific time has passed.)

Turns on or off the cancellation function of the account lockout.

004

Cancellation Time

[1 to 9999 / 60 / 1 min]

Sets the interval of the retry for accessing the local address book account after the lockout function has been executed.

This setting is enabled only if SP5413-3 is set to "1" (ON).

5414

Access Mitigation

001

Mitigation ON/OFF

Permits or does not permit consecutive access to the machine with the same ID and password.

[0 to 1 / 0 / 1]

0: OFF (Permitted)

1: ON (Not permitted)

002

Mitigation Time

Sets the prohibiting time for consecutive access to the machine with the same ID and password.

[0 to 60 / 15 / 1 min]

5415*

Password Attack

001

Permissible Number

[0 to 100 / 30 / 1 times]

Sets the threshold number of attempts to attack the system with random passwords to gain illegal access to the system.

002

Detect Time

[0 to 10 / 5 / 1 sec]

Sets a detection time to count a password attack.

5416*

Access Information

001

Access User Max Num

[50 to 200 / 200 / 1 ]

Sets the number of users for the access exclusion and password attack detection function.

002

Access Password Num

[50 to 200 / 200 / 1 ]

Sets the number of passwords for the access exclusion and password attack detection function.

003

Monitor interval

[1 to 10 / 3 / 1 sec]

Sets the interval of watching out for user information and passwords.

5417

Access Attack

001

Access Permissible number

[0 to 500 / 100 / 1]

Sets a limit on access attempts to prevent password cracking.

002

Access Detect Time

[10 to 30 / 10 / 1 sec]

Sets a detection time to count password cracking.

003

Productivity Fall Weight

[0 to 9 / 3 / 1 sec]

Sets the wait time to slow down the speed of certification when an excessive number of access attempts have been detected.

004

Attack Max Num

[50 to 200 / 200 / 1]

Sets a limit on the number of requests received for certification in order to slow down the certification speed when an excessive number of access attempts have been detected.

5420*

User Authentication

These settings should be done with the System Administrator.

 These functions are enabled only after the user access feature has been enabled.

001

Copy

[0 or 1/ 0 / 1] 0: ON. 1: OFF

Determines whether certification is required before a user can use the copy application.

011

Document Server

[0 or 1/ 0 / 1] 0: ON. 1: OFF

Determines whether certification is required before a user can use the document server.

021

Fax

[0 or 1/ 0 / 1] 0: ON. 1: OFF

Determines whether certification is required before a user can use the fax application.

031

Scanner

[0 or 1/ 0 / 1] 0: ON. 1: OFF

Determines whether certification is required before a user can use the scanner application.

041

Printer

[0 or 1/ 0 / 1] 0: ON. 1: OFF

Determines whether certification is required before a user can use the printer application.

051

SDK1

[0 or 1/ 0 / 1] 0: ON. 1: OFF

Determines whether certification is required before a user can use the SDK application.

061

SDK2

071

SDK3

081

Browser

[0 or 1/ 0 / 1] 0: ON. 1: OFF

Determines whether certification is required before a user can use the browser application.

5430

Auth Dialog Message Change

001

Message Change On/Off

Turns on or off the displayed message change for the authentication.

[0 or 1 / 0 / -]

0: Off, 1: On

002

Message Text Download

Executes the message download for the authentication.

003

Message Text ID

Inputs message text for the authentication.

5431

External Auth User Preset

010

Tag

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the tag copy permission for the external authentication.

011

Entry

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the entry information for the external authentication.

012

Group

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the group information for the external authentication.

020

Mail

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the mail information for the external authentication.

030

Fax

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the fax information for the external authentication.

031

FaxSub

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the fax additional information for the external authentication.

032

Folder

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the folder information for the external authentication.

033

ProtectCode

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the protection code information for the external authentication.

034

SmtpAuth

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the SMTP information for the external authentication.

035

LdapAuth

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the LDAP information for the external authentication.

036

Smb Ftp Fldr Auth

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the SMB/FTP information for the external authentication.

037

AcntAcl

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the account ACL information for the external authentication.

038

DocumentAcl

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the document ACL information for the external authentication.

040

CertCrypt

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the authentication information for the external authentication.

050

UserLimitCount

[0 or 1 / 1 / -]

0: Not permit, 1: Permit

Turns on or off the copy permission of the maximum number information for the external authentication.

5481

Authentication Error Code

These SP codes determine how the authentication failures are displayed.

001

System Log Disp

[0 or 1 / 0 / -]

0: OFF [Default], 1: ON

Determines whether an error code appears in the system log after a user authentication failure occurs.

002

Panel Disp

[0 or 1 / 1 / 1]

0: OFF, 1: ON [Default]

Determines whether an error code appears on the operation panel after a user authentication failure occurs.

5490

MF KeyCard (Japan only)

Sets up operation of the machine with a keycard. [0 to 1 / 0 / 1]

0: Disabled. Cancels operation without a user code. 1: Enabled. Allows operation without a user code.

5491*

Optional Counter

Determines whether to cancel the job when MK1 keycard is pulled out from the machine during job.

[0 to 11111111 / 0 / 1]

0: On. Cancels the job.

1: Off. Allows operation if MK1 keycard is pulled out from the machine during the job.

5501*

PM Alarm

001

PM Alarm Level

Sets the PM alarm level.

[0 to 9999 / 0 / 1 k copies/step] 0: No PM alarm

002

Original Count Alarm (DFU)

Selects whether the PM alarm for the number of scans is enabled or not. If this is "1", the PM alarm function is enabled.

[0 = No / 1 = Yes]

5504*

Jam Alarm

Sets the alarm to sound for the specified jam level (document misfeeds are not included).

[0 to 3 / 3 / 1 step]

0: Zero (Off)

1: Low (2.5K jams) 2: Medium (3K jams) 3: High (6K jams)

5505*

Error Alarm

Sets the number of sheets to clear the error alarm counter.

The error alarm counter counts "1" when any SC is detected. However, the error alarm counter decreases by "1" when an SC is not detected during a set number of copied sheets (for example, default 5000 (C1b) or 10000 (C1c) sheets). The error alarm occurs when the SC error alarm counter reaches "5".

[0 to 255 / 45 (C2b), 50 (C1b/C1.5b), 60 (C2c), 100 (C1c/C1.5c) / 100

copies / step]

5507*

Supply Alarm

001

Paper supply Alarm (0:Off 1:On)

Switches the control call on/off for the paper supply. (DFU)

0: Off, 1: On

0: No alarm.

1: Sets the alarm to sound for the specified number transfer sheets for each paper size (A3, A4, B4, B5, DLT, LG, LT, HLT)

002

Staple Supply Alarm (0:Off 1:On)

Switches the control call on/off for the stapler installed in the finisher. (DFU)

0: Off, 1: On

0: No alarm

1: Alarm goes off for every 1K of staples used.

003

Toner Supply Alarm (0:Off 1:On)

Switches the control call on/off for the toner end.

(DFU)

0: Off, 1: On

If you select "1" the alarm will sound when the copier detects toner end.

080

Toner Call Timing

Changes the timing of the "Toner Supply Call" via the @Remote, when the following conditions occur.

0: At replacement 1: At near end

128

Interval: Others

The "Paper Supply Call Level: nn" SPs specify the paper control call interval for the referenced paper sizes. (DFU)

[250 to 10000 / 1000 / 1 Step]

132

Interval: A3

133

Interval: A4

134

Interval: A5

141

Interval: B4

142

Interval: B5

160

Interval: DLT

164

Interval: LG

166

Interval: LT

172

Interval: HLT

5508

CC Call

001

Jam Remains

Enables/disables initiating a call. [0 to 1 / 1 / 1]

0: Disable

1: Enable

002

Continuous Jams

003

Continuous Door Open

011

Jam Detection: Time Length

Sets the length of time to determine the length of an unattended paper jam.

[3 to 30 / 10 / 1 minute]

012

Jam Detection Continuous Count

Sets the number of continuous paper jams required to initiate a call.

[2 to 10 / 5 / 1 time]

013

Door Open: Time Length

Sets the length of time the remains opens to determine when to initiate a call.

[3 to 30/ 10 / 1 minute]

5515*

SC/Alarm Setting

With @Remote in use, these SP codes can be set to issue an SC call when an SC error occurs. If this SP is switched off, the SC call is not issued when an SC error occurs.

001

SC Call

[0 or 1 / 1 / 1]

0: OFF

1: ON

002

Service Parts Near End Call

003

Service Parts End Call

004

User Call

006

Communication Information Test Call

007

Machine Information Notice

008

Alarm Notice

010

Supply Automatic Ordering Call

011

Supply Management Report Call

012

Jam/Door Open Call

5516

Individual PM Part Alarm Call

With @Remote in use, these SP codes can be set to issue an PM alarm call when one of SP parts reaches its yield.

001

Disable/Enable Setting (0: Not send, 1: Send)

[0 or 1 / 1 / - ]

0: Not send, 1: Send

004

Percent yield for triggering PM alert

[1 to 255 / 75 / 1 %/step]

5730

Extend Function Setting

DFU

5734

PDF Setting

001

PDF/A Fixed [0 or 1 / 0 / - ]

0: No Limit

1: Limited

5741

Node Authentication Timuout

DFU

5743

Network Security Level

DFU

5744

Management

DFU

5745

EcoCountTime

DFU

5747

[Vertical Scroll Bar display mode] (See IMPORTANT below)

204

Vertical Scroll Bar display mode

0: Always display (Default)

1: Display when pressing “Program Key

205

Confirmation dialog display setting

NOTE:

- If enabled, the “Page change confirmation dialog” is displayed when the user moves from the current page to a different one.

- The “SSL certificate confirmation dialog” is displayed when an SSL-related problem occurs.

- If the customer is using an internal (original) Web application, i.e. a fully trusted application, this SP can be set to “2” (do not display either dialog).

Value

Page change confirmation dialog

SSL

certificate confirmation dialog

0 (Default)

Display

Display

1

Not display

Display

2

Not Display

Not display

3

Display

Not display

IMPORTANT: Only use these SP Modes with Browser Version 2.00.0 or newer, EXJS version 1.11.00 or newer, and Specification 2.01 or newer.

206

Displayed but it should not be used (Not for field use).

5749

Import/Export NOTE: Refer to Section 3-13 Detailed Description of SP5749 for more information.

DFU

001

Import

101

Export

251

Export Result Print (SP)

252

Import Result Print (SP)

5749

Import/Export NOTE: Refer to Section 3-13 Detailed Description of SP5749 for more information.

DFU

001

Import

101

Export

251

Export Result Print (SP)

252

Import Result Print (SP)

5749

Import/Export NOTE: Refer to Section 3-13 Detailed Description of SP5749 for more information.

DFU

001

Import

101

Export

251

Export Result Print (SP)

252

Import Result Print (SP)

5792

MCS Debug SW

DFU

5793

ECS Debug SW

DFU

5801

Memory Clear

Resets NVRAM data to the default settings. Before executing any of these SP codes, print an SMC Report.

001

All Clear

Initializes items 2 to 15 below.

002

Engine

Initializes all registration settings for the engine and copy process settings.

003

SCS

Initializes default system settings, SCS (System Control Service) settings, operation display coordinates, and ROM update information.

004

IMH Memory Clr

Initializes the image file system. (IMH: Image Memory Handler)

005

MCS

Initializes the automatic delete time setting for stored documents.

(MCS: Memory Control Service)

006

Copier application

Initializes all copier application settings.

007

Fax Application

Initializes the fax reset time, job login ID, all TX/RX settings, local storage file numbers, and off-hook timer.

008

Printer Application

Initializes the printer defaults, programs registered, the printer SP bit switches, and the printer CSS counter.

009

Scanner Application

Initializes the defaults for the scanner and all the scanner SP modes.

010

Web Service

Deletes the Netfile (NFA) management files and thumbnails, and initializes the Job login ID.

Netfiles: Jobs to be printed from the document server using a PC and the DeskTopBinder software

011

NCS

Initializes the system defaults and interface settings (IP addresses also), the SmartDeviceMonitor for Admin settings, WebStatusMonitor settings, and the TELNET settings.

(NCS: Network Control Service)

012

R-FAX

Initializes the job login ID, SmartDeviceMonitor for Admin, job history, and local storage file numbers.

014

Clear DCS Setting

Initializes the DCS (Delivery Control Service) settings.

015

Clear UCS Setting

Initializes the UCS (User Information Control Service) settings.

016

MIRS Setting

Initializes the MIRS (Machine Information Report Service) settings.

017

CCS

Initializes the CCS (Certification and Charge-control Service) settings.

018

SRM Memory Clr

Initializes the SRM (System Resource Manager) settings.

019

LCS

Initializes the LCS (Log Count Service) settings.

020

Web Uapli

Initializes the web user application settings.

021

ECS

Initializes ECS (Engine Control Service).

023

AICS

Initializes the AICS settings.

5802*

FreeRun

Performs a free run on the copier engine.

The correct paper should be loaded in the 1st tray or 2nd tray, but paper is not fed.

The main switch has to be turned off and on after using the free run mode for a test.

001

TRAY1:A4LEF

-

002

TRAY2:A3

-

003

TRAY2:A4SEF

-

5803

Input Check

Displays the signals received from sensors and switches. p.3-251 "Input Check")

5804

Output Check

Turns on the electrical components individually for test purposes. ( p.3-263 "Output Check")

5805

Anti-Condensation Heater

[0 or 1 / 0 / -] 0:OFF / 1:ON

5810

SC Reset

001

Fusing SC Reset

Resets all level A service call conditions, such as fusing errors. To clear the service call, touch "Execute" on the LCD, then turn the main power switch off/on.

5811

MachineSerial

002

Display

Displays the machine serial number.

003

BCU

Inputs the serial number.

005

FRAM

Displays the FRAM serial number.

5812*

Service Tel. No. Setting

001

Service

Inputs the telephone number of the CE (displayed when a service call condition occurs.)

002

Facsimile

Use this to input the fax number of the CE printed on the Counter Report (UP mode).

003

Supply

Inputs the telephone number of the supplier displayed on the user mode screen.

004

Operation

Allows the service center contact telephone number to be displayed on the user mode screen.

5816

Remote Service

001

I/F Setting

Selects the remote service setting. [0 to 2 / 2 / 1 /step]

0: Remote service off

1: CSS remote service on 2: @Remote service on

002

CE Call

Performs the CE Call at the start or end of the service. [0 or 1 / 0 / 1 /step]

0: Start of the service 1: End of the service

NOTE: This SP is activated only when SP 5816-001 is set to “2”.

003

Function Flag

Enables or disables the remote service function. [0 to 1 / 0 / 1 /step]

0: Disabled, 1: Enabled

NOTE: This SP setting is changed to "1" after @Remote registration has been completed.

004

Communication Test Call

This SP issues a test call from a GW machine to determine whether it can communicate successfully with the call center after it has been set up for NRS. Successful return will be in the range 0 to 99.

005

Device Information Call

This SP issues a call to notify the NRS device information to the call center. Successful return will be in the range 0 to 99.

007

SSL Disable

Uses or does not use the RCG certification by SSL when calling the RCG. [0 to 1 / 0 / 1 /step]

0: Uses the RCG certification

1: Does no use the RCG certification

008

RCG Connect Timeout

Specifies the connect timeout interval when calling the RCG. [1 to 90 / 30 / 1 second /step]

009

RCG Write Timeout

Specifies the write timeout interval when calling the RCG. [0 to 100 / 60 / 1 second /step]

010

RCG Read Timeout

Specifies the read timeout interval when calling the RCG. [0 to 100 / 60 / 1 second /step]

011

Port 80 Enable

Enables/disables access via port 80 to the SOAP method. [0 or 1 / 0 / – ]

0: Disabled, 1: Enabled

012

@Remote Communication Permission

[0 to 2 / 1 / 1 ]

0: Not permitted

1: Permitted

2: Partially limit

013

RFU (Remote Firmware Update) Timing

Selects the RFU timing. [0 or 1 / 1 / – ]

0: RFU is executed whenever update request is received.

1: RFU is executed only when the machine is in the sleep mode.

014

RCG Error Cause

[0 or 1 / 0 / – ]

0: Normal

1: Fails to reflect the client/server certificate settings by network failure to reboot. Transition to 0 on restart the machine.

021

RCG–C Registed

This SP displays the Embedded RC Gate installation end flag. 0: Installation not completed

1: Installation completed

023

Connect Type (N/M)

This SP displays and selects the Embedded RC Gate connection method. [0 or 1 / 0 / 1 /step

0: Internet connection

1: Dial-up connection

061

Cert. Expire Timing DFU

Proximity of the expiration of the certification.

062

Use Proxy

This SP setting determines if the proxy server is used when the machine communicates with the service center.

063

Proxy Host

This SP sets the address of the proxy server used for communication between Embedded RC Gate-N and the gateway. Use this SP to set up or display the customer proxy server address. The address is necessary to set up Embedded RC Gate-N.

 The address display is limited to 128 characters. Characters beyond the 128 character are ignored.

 This address is customer information and is not printed in the SMC report.

064

Proxy Port Number

This SP sets the port number of the proxy server used for communication between Embedded RC Gate-N and the gateway. This setting is necessary to set up Embedded RC Gate-N.

 This port number is customer information and is not printed in the SMC report.

065

Proxy User Name

This SP sets the HTTP proxy certification user name.

 The length of the name is limited to 31 characters. Any character beyond the 31st character is ignored.

 This name is customer information and is not printed in the SMC report.

066

Proxy Password

This SP sets the HTTP proxy certification password.

 The length of the password is limited to 31 characters. Any character beyond the 31st character is ignored.

 This name is customer information and is not printed in the SMC report.

067

CERT: Up State

Displays the status of the certification update.

0

The certification used by Embedded RC Gate is set correctly.

1

The certification request (setAuthKey) for update has been received from the GW URL and certification is presently being updated.

2

The certification update is completed and the GW URL is being notified of the successful update.

3

The certification update failed, and the GW URL is being notified of the failed update.

4

The period of the certification has expired and new request for an update is being sent to the GW URL.

11

A rescue update for certification has been issued and a rescue certification setting is in progress for the rescue GW connection.

12

The rescue certification setting is completed and the GW URL is being notified of the certification update request.

13

The notification of the request for certification update has completed successfully, and the system is waiting for the certification update request from the rescue GW URL.

14

The notification of the certification request has been received from the rescue GW controller, and the certification is being stored.

15

The certification has been stored, and the GW URL is being notified of the successful completion of this event.

16

The storing of the certification has failed, and the GW URL is being notified of the failure of this event.

17

The certification update request has been received from the GW URL, the GW URL was notified of the results of the update after it was completed, but a certification error has been received, and the rescue certification is being recorded.

18

The rescue certification of No. 17 has been recorded, and the GW URL is being notified of the failure of the certification update.

068

CERT: Error

Displays a number code that describes the reason for the request for update of the certification.

0

Normal. There is no request for certification update in progress.

1

Request for certification update in progress. The current certification has expired.

2

An SSL error notification has been issued. Issued after the certification has expired.

3

Notification of shift from a common authentication to an individual certification.

4

Notification of a common certification without ID2.

5

Notification that no certification was issued.

6

Notification that GW URL does not exist.

069

CERT: Up ID

The ID of the request for certification.

083

Firm Up Status

Displays the status of the firmware update.

085

Firm Up User Check

This SP setting determines if the operator can confirm the previous version of the firmware before the firmware update execution. If the option to confirm the previous version is selected, a notification is sent to the system manager and the firmware update is done with the firmware files from the URL.

086

Firmware Size

Allows the service technician to confirm the size of the firmware data files during the firmware update execution.

087

CERT: Macro Ver.

Displays the macro version of the @Remote certification.

088

CERT: PAC Ver.

Displays the PAC version of the @Remote certification.

089

CERT: ID2 Code

Displays ID2 for the @Remote certification. Spaces are displayed as underscores (_). Asteriskes (*) indicate that no @Remote certification exists. "000000 " indicates "Common certification".

090

CERT: Subject

Displays the common name of the @Remote certification subject. CN = the following 17 bytes. Spaces are displayed as underscores (_).

Asterisks (*) indicate that no @Remote certification exists. "000000 " indicates "Common certification".

091

CERT: SerialNo.

Displays serial number for the @Remote certification. Asterisks (*) indicate that no

@Remote certification exists.

092

CERT: Issuer

Displays the common name of the issuer of the

@Remote certification. CN = the following 30 bytes. Asteriskes () indicate that no @Remote certification exists.

093

CERT: Valid Start

Displays the start time of the period for which the current @Remote certification is enabled.

094

CERT: Valid End

Displays the end time of the period for which the current @Remote certification is enabled.

096

Server CN Check

Not used

096

GW Host

Not used

097

GW URL Path

Not used

099

Debug RescueG/WURL Set

Not used

102*

CERT: Encrypt Level

Displays the encryption level for the NRS certificate. [1 or 2 / 1 / – ]

1: Indicates that the certificate encryption level is 512-bit. 2: Indicates that the certificate encryption level is 2048-bit.

150

Selection Country

Not used

151

Line Type Automatic Judgment

Not used

152

Line Type Judgment Result

Not used

153

Selection Dial / Push

Not used

154

Outside Line Outgoing Number

Not used

156

Dial Up User Name

Not used

157

Dial Up Password

Not used

161

Local Phone Number

Not used

162

Connection Timing Adjustment Incoming

Not used

163

Access Point

Not used

164

Line Connecting

Not used

173

Modem Serial No.

Not used

174

Retransmission Limit

Not used

186

RCG-C M DebugBitSW

Not used

187

FAX TX Priority

Not used

200

Manual Polling

Executes the manual polling.

201

Regist Status

Displays a number that indicates the status of the @Remote service device. 0: Neither the @Remote device nor Embedded RCG Gate is set.

1: The Embedded RCG Gate is being set. Only Box registration is completed. In this status, @Remote device cannot communicate with this device.

2: The Embedded RCG Gate is set. In this status, the @Remote device cannot communicate with this device.

3: The @Remote device is being set. In this status the Embedded RCG Gate cannot be set.

4: The @Remote module has not started.

202

Letter Number

Allows entry of the request number needed for the Embedded RCG Gate.

203

Confirm Execute

Executes the confirmation request to the @Remote Gateway.

204

Confirm Result

Displays a number that indicates the result of the confirmation executed with SP5816-203.

0: Succeeded

1: Confirmation number error 2: Registration in progress

3: Proxy error (proxy enabled) 4: Proxy error (proxy disabled)

5: Proxy error (Illegal user name or password) 6: Communication error

7: Certification update error 8: Other error

9: Confirmation executing

205

Confirm Place

Displays the result of the notification sent to the device from the Gateway in answer to the confirmation request. Displayed only when the result is registered at the Gateway.

206

Register Execute

Executes "Embedded RCG Registration".

207

Register Result

Displays a number that indicates the registration result. 0: Succeeded

2: Registration in progress

3: Proxy error (proxy enabled) 4: Proxy error (proxy disabled)

5: Proxy error (Illegal user name or password) 6: Communication error

7: Certification update error 8: Other error

9: Registration executing

208

Error Code

Displays a number that describes the error code that was issued when either SP5816-204 or SP5816-207 was executed.

Cause

Code

Meaning

Illegal Modem Parameter

-11001

Chat parameter error

-11002

Chat execution error

-11003

Unexpected error

Operation Error, Incorrect Setting

-12002

Inquiry, registration attempted without acquiring device status.

-12003

Attempted registration without execution of an inquiry and no previous registration.

-12004

Attempted setting with illegal entries for certification and ID2.

-12005

@Remote communication is prohibited.

The device has an Embedded RC gate-related problem.

-12006

A confirmation request was made after the confirmation had been already completed.

-12007

The request number used at registration was different from the one used at confirmation.

-12008

Update certification failed because mainframe was in use.

-12009

ID2 mismatch between an individual certification and NVRAM

-12010

Certification area is not initialized.

Error Caused by Response from GW URL

-2385

Attempted dial up overseas without the correct international prefix for the telephone number.

-2387

Not supported at the Service Center

-2389

Database out of service

-2390

Program out of service

-2391

Two registrations for same device

-2392

Parameter error

-2393

RCG device not managed

-2394

Device not managed

-2395

Box ID for RCG device is illegal

-2396

Device ID for RCG device is illegal

-2397

Incorrect ID2 format

-2398

Incorrect request number format

209

Instl Clear

Releases the machine from its Embedded RCG Gate setup.

NOTE: Turn off and on the main power switch after this setting has been changed.

250

CommLog Print

Prints the communication log.

5821*

Remote Service Address

002

RCG IP Address

Sets the IP address of the RCG (Remote Communication Gate) destination for call processing at the remote service center. [00000000h to FFFFFFFFh / 00000000h / 1]

003

RCG Port

Sets the port number of the RCG (Remote Communication Gate) destination for call processing at the remote service center. [0 to 65535 / 443 / 1]

004

RCG URL Path

Sets the URL path of the RCG (Remote Communication Gate) destination for call processing at the remote service center. [0 to 16 characters / /RCG/services/ /-]

5824

NV-RAM Data Upload

Uploads the NVRAM data to an SD card. Push Execute.

Note: When uploading data in this SP mode, the front door must be open.

5825

NV-RAM Data Download

Downloads data from an SD card to the NVRAM in the machine. After downloading is completed, remove the card and turn the machine power off and on.

5828

Network Setting

001

IPv4 Address (Ethernet/IEEE 802.11)

This SP allows you to check and reset the IPv4 address for Ethernet and wireless LAN (802.11): aaa.bbb.ccc.ddd

002

IPv4 Subnet Mask (Ethernet/IEEE 802.11)

This SP allows you to check and reset the IPv4 subnet mask for Ethernet and wireless LAN (802.11): aaa.bbb.ccc.ddd

003

IPv4 Default Gateway (Ethernet/IEEE 802.11)

This SP allows you to check and reset the IPv4 default gateway used by the network for Ethernet and wireless LAN (802.11): aaa.bbb.ccc.ddd

006

DHCP (Ethernet/IEEE 802.11)

This SP code allows you check and change the setting that determines whether the IP address is used with DHCP on an Ethernet or wireless (802.11) LAN network.

[0 to 1 / 1 / 1]

0: Not used (manual setting) 1: Used

021

Active IPv4 Address

This SP allows you to check the IPv4 address that was used when the machine started up with DHCP.

022

Active IPv4 Subnet Mask

This SP allows you to check the IPv4 subnet mask setting that was used when the machine started up with DHCP.

023

Active IPv4 Gateway Address

This SP allows you to check the IPv4 default gateway setting that was used when the machine started up with DHCP.

090

TELNET (0:OFF 1:ON)

Disables or enables Telnet operation. If this SP is disabled, the Telnet port is closed.

[0 to 1 / 1 / 1]

0: Disable, 1: Enable

091

Web

(0:OFF 1:ON)

Disables or enables the Web operation. [0 to 1 / 1 / 1]

0: Disable, 1: Enable

145

Active IPv6 Link Local Address

This is the IPv6 local address referenced on the Ethernet or wireless LAN (802.11) in the format: "Link-Local address" + "Prefix Length"

The IPv6 address consists of a total 128 bits configured in 8 blocks of 16 bits each. These notations can be abbreviated. See "Note: IPV6 Addresses " below this table.

147

Active IPv6 Stateless Address 1

These SPs are the IPv6 stateless addresses (1 to 5) referenced on the Ethernet or wireless LAN (802.11) in the format:

"Stateless Address" + "Prefix Length"

The IPv6 address consists of a total 128 bits configured in 8 blocks of 16 bits each.

149

Active IPv6 Stateless Address 2

151

Active IPv6 Stateless Address 3

153

Active IPv6 Stateless Address 4

155

Active IPv6 Stateless Address 5

156

IPv6 Manual Address

This SP is the IPv6 manually set address referenced on the Ethernet or wireless LAN (802.11) in the format:

"Manual Set Address" + "Prefix Length"

The IPv6 address consists of a total 128 bits configured in 8 blocks of 16 bits each. These notations can be abbreviated. See "Note: IPV6 Addresses" below this table.

158

IPv6 Gateway Address

This SP is the IPv6 gateway address referenced on the Ethernet or wireless LAN (802.11). The IPv6 address consists of a total 128 bits configured in 8 blocks of 16 bits each. These notations can be abbreviated. See "Note: IPV6 Addresses" below this table.

Note: IPV6 Addresses

Ethernet and the Wireless LAN (802.11) reference the IPV6 "Link-Local address + Prefix Length". The IPV6 address consists of 128 bits divided into 8 blocks of 16 bits: aaaa:bbbb:cccc:dddd:eeee:ffff:gggg:hhhh:

The prefix length is inserted at the 17th byte (Prefix Range: 0x0 to 0x80). The initial setting is 0x40 (64).

For example, the data: "2001123456789012abcdef012345678940h" is expressed: "2001:1234:5678:9012:abcd:ef01:2345:6789": prefixlen 64

However, the actual IPV6 address display is abbreviated according to the following rules.

Rules for Abbreviating IPV6 Addresses

1. The IPV6 address is expressed in hexadecimal delimited by colons (:) with the following characters:

0123456789abcdefABCDEF

2. A colon is inserted as a delimiter every 4th hexadecimal character. fe80:0000:0000:0000:0207:40ff:0000:340e

3. The notations can be abbreviated by eliminating zeros where the MSB and digits following the MSB are zero. The example in "2" above, then, becomes fe80:0:0:0207:40ff:0:340e

4. Sections where only zeros exist can be abbreviated with double colons (::). This abbreviation can be done also where succeeding sections contain only zeros (but this can be done only at one point in the address). The example in "2" and "3" above then becomes:

fe80::207:40ff:0:340e (only the first null sets zero digits are abbreviated as "::")

-or-

fe80:0:0:0:207:40ff::340e (only the last null set before "340e" is abbreviated as "::")

161

IPv6 Stateless Auto Setting

Enable or disables the automatic setting for IPv6 stateless.

[0 or 1 / 1 / 1]

1: Enable, 0: Disable

236

Web Item visible

Displays or does not display the Web system items.

[0 x 0000 to 0 x ffff / 0 x ffff] 0: Not displayed, 1: Displayed bit0: Net RICOH

bit1: Consumable Supplier bit2-15: Reserved (all)

237

Web shopping link visible

Displays or does not display the link to Net RICOH on the top page and link page of the web system.

[0 to 1 / 1 / 1]

0: Not display, 1:Display

238

Web supplies Link visible

Displays or does not display the link to Consumable Supplier on the top page and link page of the web system.

[0 to 1 / 1 / 1]

0: Not display, 1:Display

239

Web Link1 Name

This SP confirms or changes the URL1 name on the link page of the web system. The maximum characters for the URL name are 31 characters.

240

Web Link1 URL

his SP confirms or changes the link to URL1 on the link page of the web system. The maximum characters for the URL are 127 characters.

241

Web Link1 visible

Displays or does not display the link to URL1 on the top page of the web system.

[0 to 1 / 1 / 1]

0: Not display, 1:Display

242

Web Link2 Name

Same as "-239"

243

Web Link2 URL

Same as "-240"

244

Web Link2 visible

Same as "-241"

249

DHCPv6 DUID

Sets DHCPv6 DUID. [0000000000000000000000000000h to FFFFFFFFFFFFFFFFFFFFFFFFFFFFh / 0000000000000000000000000000h / -]

5832

HDD

Enter the SP number for the partition to initialize, then press #. When the execution ends, cycle the machine off and on.

001

HDD Formatting (All)

002

HDD Formatting (IMH)

003

HDD Formatting (Thumbnail)

004

HDD Formatting (Job Log)

005

HDD Formatting (Printer Fonts)

006

HDD Formatting (User Info)

007

Mail RX Data

008

Mail TX Data

009

HDD Formatting (Data for Design)

010

HDD Formatting (Log)

011

HDD Formatting (Ridoc I/F) (for Ridoc Desk Top Binder)

5836*

Capture Setting

001

Capture Function (0:Off 1:On)

With this function disabled, the settings related to the capture feature cannot be initialized, displayed, or selected.

[0 to 1 / 0 / 1]

0: Disable, 1: Enable

002

Panel Setting

Determines whether each capture related setting can be selected or updated from the initial system screen.

[0 to 1 / 0 / 1]

0: Disable, 1: Enable

The setting for SP5836-001 has priority.

072

Reduction for Copy B&W Text

[0 to 6 / 0 / 1]

0:1, 1:1/2, 2:1/3, 3:1/4, 6:2/3

073

Reduction for Copy B&W Other

[0 to 6 / 0 / 1]

0:1, 1:1/2, 2:1/3, 3:1/4, 6:2/3

075

Reduction for Printer B&W

[0 to 6 / 0 / 1]

0 1, 1:1/2, 2:1/3, 3:1/4, 6:2/3

078

Reduction for Printer B&W 1200

1: 1/2, 3: 1/4, 4: 1/6, 5: 1/8

082

Format for Copy B&W Text

[0 to 3 / 1 / 1]

0: JFIF/JPEG, 1: TIFF/MMR, 2:

TIFF/MH, 3: TIFF/MR

083

Format Copy B&W Other

[0 to 3 / 1 / 1]

0: JFIF/JPEG, 1: TIFF/MMR, 2:

TIFF/MH, 3: TIFF/MR

085

Format for Printer B&W

[0 to 3 / 1 / 1]

0: JFIF/JPEG, 1: TIFF/MMR, 2:

TIFF/MH, 3: TIFF/MR

091

Default for JPEG

[5 to 95 / 50 / 1]

Sets the JPEG format default for documents sent to the document management server with the MLB, with JPEG selected as the format. Enabled only when optional File Format Converter (MLB: Media Link Board) is installed.

101

Primary srv IP address

Sets the IP address for the primary capture server. This is basically adjusted by the remote system.

102

Primary srv scheme

This is basically adjusted by the remote system.

103

Primary srv port number

This is basically adjusted by the remote system.

104

Primary srv URL path

This is basically adjusted by the remote system.

111

Secondary srv IP address

Sets the IP address for the secondary capture server. This is basically adjusted by the remote system.

112

Secondary srv scheme

This is basically adjusted by the remote system.

113

Secondary srv port number

This is basically adjusted by the remote system.

114

Secondary srv URL path

This is basically adjusted by the remote system.

122

Reso: Copy (Mono)

[0 to 255 / 3 / 1/step]

Selects the resolution for BW copy mode. This is basically adjusted by the remote system.

0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi

124

Reso: Print (Mono)

This is basically adjusted by the remote system.

[0 to 255 / 3 / 1/step]

Selects the resolution for BW print mode. This is basically adjusted by the remote system.

0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi

126

Reso: Fax (Mono)

This is basically adjusted by the remote system.

[0 to 255 / 3 / 1/step]

Selects the resolution for BW fax mode. This is basically adjusted by the remote system.

0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi/ 6: 75dpi

127

Reso: Scan (Color)

This is basically adjusted by the remote system.

[0 to 255 / 4 / 1/step]

Selects the resolution for color scanning mode. This is basically adjusted by the remote system.

0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi/ 6: 75dpi

128

Reso: Scan (Mono)

This is basically adjusted by the remote system.

[0 to 255 / 3 / 1/step]

Selects the resolution for BW scanning mode. This is basically adjusted by the remote system.

0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi/ 6: 75dpi

141

All Addr Info Switch

[0 or 1 / 1 / -]

0: Off, 1: On

Turns on or off the all address information transmission for the captured resources.

142

Stand-by Doc Max Number

[10 to 9999 / 2000 / 1/step]

Selects the maximum number of captured documents to be transmitted to the document server.

5840*

IEEE 802.11

006

Channel MAX

Sets the maximum range of the bandwidth for the wireless LAN. This bandwidth setting varies for different countries.

[1 to 14 / 11 (NA), 13 (EU), 14 (JPN) / 1]

JPN: 1 to 14, NA: 1 to 11, EU: 1 to 13

007

Channel MIN

Sets the minimum range of the bandwidth for operation of the wireless LAN. This bandwidth setting varies for different countries.

[1 to 14 / 1 / 1]

JPN: 1 to 14, NA: 1 to 11, EU: 1 to 13

008

Transmission speed

[0 x 00 to 0 x FF / 0 x FF to Auto / -]

0 x FF to Auto [Default] 0 x 11 - 55M Fix

0 x 10 - 48M Fix

0 x 0F - 36M Fix

0 x 0E - 18M Fix

0 x 0D - 12M Fix 0 x 0B - 9M Fix 0 x 0A - 6M Fix

0 x 07 - 11M Fix

0 x 05 - 5.5M Fix

0 x 08 - 1M Fix

0 x 13 - 0 x FE (reserved)

0 x 12 - 72M (reserved)

0 x 09 - 22M (reserved)

011

WEP Key Select

Selects the WEP key. Bit 1 and 0

00: Key1, 01: Key2 (Reserved),

10: Key3 (Reserved), 11: Key4(Reserved)

This SP is displayed only when the IEEE802.11 card is installed.

013

RTS/CTS Thresh

Adjusts the RTS/CTS threshold for the IEEE802.11 card. [0 to 3000 / 2432 / 1]

This SP is displayed only when the IEEE802.11 card is installed.

042

Fragment Thresh

Adjusts the fragment threshold for the IEEE802.11 card. [256 to 2346 / 2346 / 1]

This SP is displayed only when the IEEE802.11 card is installed.

043

11g CTS to Self

Determines whether the CTS self function is turned on or off. [0 to 1 / 1 / 1] 0: Off, 1: On

This SP is displayed only when the IEEE802.11 card is installed.

044

11g Slot Time

Selects the slot time for IEEE802.11. [0 to 1 / 0 / 1] 0: 20 m, 1: 9 m

This SP is displayed only when the IEEE802.11 card is installed.

045

WPA Debug Lvl

Selects the debug level for WPA authentication application. [1 to 3 / 3 / 1] 1: Info, 2: warning, 3: error

This SP is displayed only when the IEEE802.11 card is installed.

5841*

Supply Name Setting

Press the User Tools key. These names appear when the user presses the Inquiry button on the User Tools screen.

001

Toner Name Setting: Black

007

OrgStamp

011

StapleStd1

012

StapleStd2

013

StapleStd3

014

StapleStd4

021

StapleBind1

022

StapleBind2

023

StapleBind3

5842*

GWWS Analysis (DFU)

Bit

Groups

0

System & other groups (LSB)

This is a debugging tool. It

1

Capture related

sets the debugging output

2

Certification related

mode of each Net File

3

Address book related

process.

Bit SW 0011 1111

4

Machine management related

5

Output related (printing, delivery)

6

Repository related

001

Setting 1

Default: 00000000 – do not change

Netfiles: Jobs to be printed from the document server using a PC and the DeskTopBinder software

002

Setting 2

Adjusts the debug program mode setting. Bit7: 5682 mmseg-log setting

0: Date/Hour/Minute/Second

1: Minute/Second/Msec.

0 to 6: Not used

5844

USB

001

Transfer Rate

Sets the speed for USB data transmission. [0 x 01 or 0 x 04 / 0 x 04 /-]

0 x 01 [Full Speed], 0 x 04 [Auto Change]

002

Vendor ID

Sets the vendor ID:

Initial Setting: 0x05A Ricoh Company [0x0000 to 0xFFFF/1] (DFU)

003

Product ID

Sets the product ID. [0x0000 to 0xFFFF/1] (DFU)

004

Device Release No.

Sets the device release number of the BCD (binary coded decimal) display. [0000 to 9999 / 100 / 1] (DFU)

Enter as a decimal number. NCS converts the number to hexadecimal number recognized as the BCD.

005

Fixed USB Port

This SP standardizes for common use the model name and serial number for USB PnP (Plug & Play). It determines whether the driver requires

re-installation. [0 to 2 / 0 / 1]

0: OFF

1: Level 1

2: Level 2

006

PnP Model Name

This SP sets the model name to be used by the USB PnP when "Function Enable (Level 2) is set so the USB Serial No. can have a common name (SP5844-5).

Default: Laser Printer (up to 20 characters allowed).

007

PnP Serial Number

This SP sets the serial number to be used by the USB PnP when "Function Enable (Level 2)

set so the USB Serial No. can have a common name (SP5844-5). Default: None (up to 12 characters allowed for entry).

 Make sure that this entry is the same as the serial number in use.

 At initialization the serial number generated from the model name is used, not the setting of this SP code.

 At times other than initialization, the value set for this SP code is used.

100

Notify Unsupport

This SP determines whether an alert message appears on the control panel when a USB device (unsupported device) that cannot use an A-connector is connected.

[0 to 1 / 1 / 1]

0: Function enable

1: Function disable

 An unsupported device is a device that cannot use the functions of the USB device. For example, a USB mouse cannot be used even if it connected.

 If the PictBridge option is not mounted, even if a digital camera is connected it cannot be used because it is an unsupported device.

5845*

Delivery Server Setting

These are delivery server settings.

001

FTP Port No.

[0 to 65535 / 3670 / 1]

002

IP Address (Primary)

Use this SP to set the Scan Router Server address. The IP address under the transfer tab can be used with the initial system setting.

[Range: 000.000.000.000 to 255.255.255.255]

006

Delivery Error Display Time

Use this setting to set the length of time that the message is shown when a test error occurs during document transfer with the NetFile application and an external device.

[0 to 999 / 300 / 1 sec]

008

IP Address (Secondary)

Sets the IP address that is given to the computer that is the secondary delivery server for Scan Router. This SP lets you set only the IP address, and does not refer to the DNS setting.

[Range: 000.000.000.000 to 255.255.255.255]

009

Delivery Server Model

Lets you change the model of the delivery server that is registered by the I/O device.

[0 to 4 / 0 / 1 step]

0: Unknown

1: SG1 Provided

2: SG1 Package

3: SG2 Provided

4: SG2 Package

010

Delivery Svr. Capability

Changes the functions that the registered I/O device can do. [0 to 255 / 0 / 1 step]

Bit7 = 1 Comment information exits

Bit6 = 1 Direct specification of mail address possible Bit5 = 1 Mail RX confirmation setting possible

Bit4 = 1 Address book automatic update function exists Bit3 = 1 Fax RX delivery function exists

Bit2 = 1 Sender password function exists

Bit1 = 1 Function to link MK-1 user and Sender exists

Bit0 = 1 Sender specification required (if set to 1, Bit6 is set to "0")

011

Delivery Svr.Capability (Ext)

These settings are for future use. They will let you increase the number of registered devices (in addition to those registered for SP5845 010).

There are eight bits (Bit 0 to Bit 7). All are unused at this time.

013

Server Scheme (Primary)

014

Server port Number (Primary)

[1 to 65535 / 80 / 1]

015

Server URL Path (Primary)

016

Server Scheme (Secondary)

017

Server Port Number(Secondary)

[1 to 65535 / 80 / 1]

018

Server URL Path (Secondary)

022

Rapid Sending Control

[0 to 1 / 1 / -]

0: Disable, 1: Enable

Enables or disables the prevention function for the continuous data sending error.

5846*

UCS Setting

001

Machine ID (for Delivery Server)

Displays the unique device ID in use by the delivery server directory. The value is only displayed and cannot be changed.

This ID is created from the NIC MAC or IEEE 1394 EUI. The ID is displayed as either 6-byle or 8-byte binary.

002

Machine ID Clear (for Delivery Server)

Clears the unique ID of the device used as the name in the file transfer directory. Execute this SP if the connection of the device to the delivery server is unstable. After clearing the ID, the ID will be established again automatically by cycling the machine off and on.

003

Maximum Entries

Changes the maximum number of entries that UCS can handle. [2000 to 20000 / 2000 / 1 step]

If a value smaller than the present value is set, the UCS managed data is cleared, and the data (excluding user code information) is displayed.

006

Delivery Server Retry Timer

Sets the interval for retry attempts when the delivery server fails to acquire the delivery server address book.

[0 to 255 / 0 / 1 step]

0: No retries

007

Delivery Server Retry Times

Sets the number of retry attempts when the delivery server fails to acquire the delivery server address book.

[0 to 255 / 0 / 1step]

008

Delivery Server Maximum Entries

Lets you set the maximum number of account entries and information about the users of the delivery server controlled by UCS.

[2000 to 20000 / 2000 / 1 step]

010

LDAP Search Timeout

Sets the length of the time-out for the search of the LDAP server. [1 to 255 / 60 /1 step]

020

WSD Maximum Entries

WSD (Web Services on Devices) is the Microsoft standard for connectivity to web-service enabled devices.

[50 to 250 / 250 / 1]

021

Folder Auth Change

This SP determines whether the user login information (Login User name and Password) or address (destination setting in the address book for

Scan-to-SMB) is used to permit folder access. The machine must be cycled off/on for this setting to take effect if it is changed.

[0 to 1 / 0 / 1]

0: Login User

Uses operator login information (initial value of main machine) 1: Destination

Uses address authorization information

022

Initial Value of Upper Limit Count

[0 to 999999 / 500 / 1]

040

Addr Book Migration (USB -> HDD)

This SP moves the address book data from the SD card or flash ROM on the controller board to the HDD. You must cycle the machine off and on after executing this SP.

1. Turn the machine off.

2. Install the HDD.

3. Turn the machine on. 4. Do SP5846 040.

5. Turn the machine off/on.

 Executing this SP overwrites any address book data already on the HDD with the data from the flash ROM on the controller board.

 We recommend that you back up all directory information to an SD card with SP5846-051 before you execute this SP.

 After the address book data is copied to HDD, all the address book data is deleted from the flash ROM. If the operation fails, the data is not erased from the flash ROM.

041

Fill Addr Acl Info.

This SP must be executed immediately after installation of an HDD unit in a basic machine that previously had no HDD. The first time the machine is powered on with the new HDD installed, the system automatically takes the address book from the NVRAM and writes it onto the new HDD. However, the new address book on the HDD can be accessed only by the system administrator at this stage. Executing this SP by the service technician immediately after power on grants full address book access to all users.

Procedure

1. Turn the machine off.

2. Install the new HDD.

3. Turn the machine on.

4. The address book and its initial data are created on the HDD automatically. However, at this point the address book can be accessed by only the system administrator or key operator.

5. Enter the SP mode and do SP5846 041. After this SP executes successfully, any user can access the address book.

043

Addr Book Media

Displays the slot number where an address book data is in. [0 to 30 / - /1]

0: Unconfirmed

1: SD Slot 1

2: SD Slot 2

4: USB Flash ROM

20: HDD

30: Nothing

046

Initialize All Setting & Addr Book

Initializes all settings and the address book.

047

Initialize Local Address Book

Clears all of the address information from the local address book of a machine managed with UCS.

048

Initialize Delivery Addr Book

Push [Execute] to delete all items (this does not include user codes) in the delivery address book that is controlled by UCS.

049

Initialize LDAP Addr Book

Push [Execute] to delete all items (this does not include user codes) in the LDAP address book that is controlled by UCS.

050

Initialize All Addr Book

Clears everything (including users codes) in the directory information managed by UCS. However, the accounts and passwords of the system administrators are not deleted.

051

Backup All Addr Book

Copies all directory information to the SD card. Do this SP before replacing the controller board or HDD. The operation may not succeed if the controller board or HDD is damaged.

052

Restore All Addr Book

Copies back all directory information from the SD card to the flash ROM or HDD. Upload the address book from the old flash ROM or HDD with SP5846-51 before removing it. Do SP5846 52 after installing the new HDD.

053

Clear Backup Info

Deletes the address book uploaded from the SD card in the slot 2. Deletes only the files uploaded for that machine. This feature does not work if the card is write-protected.

Note: After you do this SP, go out of the SP mode, turn the power off. Do not remove the SD card until the Power LED stops flashing.

060

Search Option

This SP uses bit switches to set up the fuzzy search options for the UCS local address book.

Bit

Meaning

0

Checks both upper/lower case characters

1

Japan Only

2

3

4

--- Not Used ---

5

--- Not Used ---

6

--- Not Used ---

7

--- Not Used ---

062

Complexity Option 1

Use this SP to set the conditions for password entry to access the local address book. Specifically, this SP limits the password entry to upper case and sets the length of the password.

[0 to 32 / 0 / 1step]

 This SP does not normally require adjustment.

 This SP is enabled only after the system administrator has set up a group password policy to control access to the address book.

063

Complexity Option 2

Use this SP to set the conditions for password entry to access the local address book. Specifically, this SP limits the password entry to lower case and defines the length of the password.

[0 to 32 / 0 / 1step]

 This SP does not normally require adjustment.

 This SP is enabled only after the system administrator has set up a group password policy to control access to the address book.

064

Complexity Option 3

Use this SP to set the conditions for password entry to access the local address book. Specifically, this SP limits the password entry to numbers and defines the length of the password.

[0 to 32 / 0 / 1step]

 This SP does not normally require adjustment.

 This SP is enabled only after the system administrator has set up a group password policy to control access to the address book.

065

Complexity Option 4

Use this SP to set the conditions for password entry to access the local address book. Specifically, this SP limits the password entry to symbols and defines the length of the password.

[0 to 32 / 0 / 1step]

 This SP does not normally require adjustment.

 This SP is enabled only after the system administrator has set up a group password policy to control access to the address book.

091

FTP Auth Port Setting

Sets the FTP port to get the delivery server address book that is used in the individual authorization mode.

[0 to 65535 / 3671 / 1step]

094

Encryption Start

Shows the status of the encryption function of the address book on the LDAP server.

[0 to 255 / 1 ] No default

5847*

Rep Resolution Reduction

5847-2 through 5847-6 changes the default settings of image data sent externally by the Net File page reference function.

5847-21 sets the default for JPEG image quality of image files controlled by NetFile.

"NetFile" refers to jobs to be printed from the document server with a PC and the DeskTopBinder software.

002

Rate for Copy B&W Text

[0 to 6 / 0 / 1]

0: 1x

1: 1/2x

2: 1/3x

3: 1/4x

4: 1/5x

5: 1/8x

6: 2/3x1

003

Rate for Copy B&W Other

[0 to 6 / 0 / 1]

005

Rate for Printer B&W

[0 to 6 / 0 / 1]

007

Rate for Printer B&W 1200dpi

[0 to 6 / 1 / 1]

021

Network Quality Default for JPEG

Sets the default value for the quality of JPEG images sent as NetFile pages. This function is available only with the MLB (Media Link Board) option installed.

[5 to 95 / 50 / 1step]

5848*

Web Service

5848-2 sets the 4-bit switch assignment for the access control setting. Setting of 0001 has no effect on access and delivery from Scan Router. 5848-100 sets the maximum size of images that can be downloaded. The default is equal to 1 gigabyte.

002

Acc. Ctrl.: Repository (only Lower 4 Bits)

0000: No access control 0001: Denies access to DeskTop Binder.

003

Acc. Ctrl.: Doc. Svr. Print (Lower 4 Bits)

Switches access control on and off.

0000: OFF, 0001: ON

004

Acc. Ctrl.: User Directory (Lower 4 Bits)

007

Acc. Ctrl Comm. Log Fax (Lower 4 Bits)

009

Acc. Ctrl.: Job Control (Lower 4 Bits)

011

Acc. Ctrl: Device Management (Lower 4 Bits)

021

Acc. Ctrl: Delivery (Lower 4 Bits)

022

Acc. Ctrl: User Administration (Lower 4 Bits)

099

Repository: Download Image Setting

100

Repository: Download Image Max. Size

Specified the max size of the image data that the machine can download/ [1 to 2048 / 2048 / 1 MB]

210

Setting: Log Type: Job 1

No information is available at this time.

211

Setting: Log Type: Job 2

No information is available at this time.

212

Setting: Log Type: Access

No information is available at this time.

213

Setting: Primary Srv

No information is available at this time.

214

Setting: Secondary Srv

No information is available at this time.

215

Setting: Start Time

No information is available at this time.

216

Setting: Interval Time

No information is available at this time.

217

Setting: Timing

No information is available at this time.

5849

Installation Date

Displays or prints the installation date of the machine.

001

Display

The "Counter Clear Day" has been changed to "Installation Date" or "Inst. Date".

002

Switch to Print

Determines whether the installation date is printed on the printout for the total counter.

[0 to 1 / 1 / -]

0: OFF (No Print) 1: ON (Print)

003

Total Counter

When the total number of pages that are made reaches this value, the current date becomes the 'official' installation date for this machine.

[0 to 99999999 / 0 / 1]

5850*

Address Book Function Japan Only

003

Replacement of Circuit Classification

The machine is sold ready to use with a G3 line. This SP allows you to switch all at once to convert to G4 after you add a G4 line. Conversely, if for some reason the G4 line becomes unusable, you can easily switch back to G3.

5851*

Bluetooth

Sets the operation mode for the Bluetooth Unit. Press either key.

[0: Public] / [1: Private]

5853

Stamp Data Download

Push [Execute] to download the fixed stamp data from the machine ROM onto the hard disk. Then these stamps can be used by the system. If this is not done, the user will not have access to the fixed stamps ("Confidential", "Secret", etc.).

You must always execute this SP after replacing the HDD or after formatting the HDD. Always switch the machine off and on after executing this SP.

5856

Remote ROM Update

002

When set to "1" allows reception of firmware data via the local port (IEEE 1284) during a remote ROM update. This setting is reset to zero after the machine is cycled off and on. Allows the technician to upgrade the firmware using a parallel cable

[0 to 1 / 0 / 1 step]

0: Not allowed

1: Allowed

5857

Save Debug Log

001

On/Off (1:ON 0:OFF)

Switches on the debug log feature. The debug log cannot be captured until this feature is switched on.

[0 to 1 / 0 / 1]

0: OFF, 1: ON

002

Target (2: HDD 3: SD)

Selects the destination where the debugging information generated by the event selected by SP5858 will be stored if an error is generated

[2 to 3 / 2 / 1]

2: HDD, 3: SD Card

005

Save to HDD

Specifies the decimal key number of the log to be written to the hard disk.

006

Save to SD Card

Specifies the decimal key number of the log to be written to the SD Card.

009

Copy HDD to SD Card (Latest 4 MB)

Takes the most recent 4 MB of the log written to the hard disk and copies them to the SD Card.

A unique file name is generated to avoid overwriting existing file names on the SD Card. Up to 4MB can be copied to an SD Card. 4 MB segments can be copied one by one to each SD Card.

010

Copy HDD to SD Card Latest 4 MB Any Key)

Takes the log of the specified key from the log on the hard disk and copies it to the SD Card.

A unique file name is generated to avoid overwriting existing file names on the SD Card. Up to 4 MB can be copied to an SD Card. 4 MB segments can be copied one by one to each SD Card. This SP does not execute if there is no log on the HDD with no key specified.

011

Erase HDD Debug Data

Erases all debug logs on the HDD

012

Erase SD Card Debug Data

Erases all debug logs on the SD Card. If the card contains only debugging files generated by an event specified by SP5858, the files are erased when SP5857 010 or 011 is executed.

To enable this SP, the machine must be cycled off and on.

013

Free Space on SD Card

Displays the amount of space available on the SD card.

014

Copy SD to SD (Latest 4MB)

Copies the last 4MB of the log (written directly to the card from shared memory) onto an SD card.

015

Copy SD to SD (Latest 4MB Any Key)

This SP copies the log on an SD card (the file that contains the information written directly from shared memory) to a log specified by key number.

016

Make HDD Debug

This SP creates a 32 MB file to store a log on the HDD.

017

Make SD Debug

This SP creates a 4 MB file to store a log on an SD card.

5858*

Debug Save When

These SPs select the content of the debugging information to be saved to the destination selected by SP5857-002.

SP5858-003 stores one SC specified by number.

001*

Engine SC Error (0:OFF 1:ON)

Stores SC codes generated by copier engine errors.

002*

Controller SC Error (0:OFF 1:ON)

Stores SC codes generated by GW controller errors.

003*

Any SC Error

[0 to 65535 / 0 / 1step]

004*

Jam (0:OFF 1:ON)

Stores jam errors.

5859*

Debug Save Key No.

001

Key

1

These SPs allow you to set up to 10 keys for log files for functions that use common memory on the controller board. [0 to 9999999 / 0 / 1]

002

Key

2

003

Key

3

004

Key

4

005

Key

5

006

Key

6

007

Key

7

008

Key

8

009

Key

9

010

Key

10

5860*

SMTP/POP3/IMAP4

020

Partial Mail Receive Timeout

[1 to 168 / 72 / 1 hour]

Sets the amount of time to wait before saving a mail that breaks up during reception. The received mail is discarded if the remaining portion of the mail is not received during this prescribed time.

021

MDN Response RFC2298 Compliance

Determines whether RFC2298 compliance is switched on for MDN reply mail.

[0 to 1 / 1 / 1]

0: No, 1: Yes

022

SMTP Auth. From Field Replacement

Determines whether the FROM item of the mail header is switched to the validated account after the SMTP server is validated.

[0 to 1 / 0 / 1]

0: No. "From" item not switched. 1: Yes. "From" item switched.

025

SMTP Auth Direct Sending

Select the authentication method for SMPT. Bit 0: LOGIN

Bit 1: PLAIN

Bit 2: CRAM_MD5

Bit 3: DIGEST_MD5

Bit 4 to Bit 7: Not Used

 This SP is activated only when SMTP authentication is enabled by UP mode.

026

S/MIME: MIME Header Setting

Selects the MIME header type of an E-mail sent by S/MIME. [0 to 2 / 0 / 1]

0: Microsoft Outlook Express standard 1: Internet Draft standard

2: RFC standard

028

S/MIME: Authentication Check

When sending S/MIME mail, specify whether to check the destination authentication.

[0 to 1 / 0 / 1]

0: Not checked

1: Checked

5866

E-Mail Report

001

Report Validity

Enables or disables the E-mail alert function. [0 or 1 / 0 / – ] 0: Enabled, 1: Disabled

005

Add Date Field

Adds or does not add the date field to the header of the alert mail.

[0 or 1 / 0 / – ]

0: Not added, 1: Added

5870

Common Key Info Writing

001

Writing

Writes to flash ROM the common proof for validating the device for @Remote specifications.

003

Initialize

Initializes the data area of the common proof for validating.

004

Writing: 2048bit

Writes to flash ROM the common proof (2048-bit) for validating the device for @Remote specifications.

5873

SD Card Appli. Move

Allows you to move applications from one SD card another. For more, see "SD Card Appli Move" in the chapter "System Maintenance (Main Chapters).

001

Move Exec

Executes the move from one SD card to another.

002

Undo Exec

This is an undo function. It cancels the previous execution.

5875

SC Auto Reboot

This SP determines whether the machine reboots automatically when an SC error occurs.

 The reboot does not occur for Type A SC codes.

001

Reboot Setting

[0 to 1/ 0 / 1]

0: The machine reboots automatically when the machine issues an SC error and logs the SC error code. If the same SC occurs again, the machine does not reboot.

1: The machine does not reboot when an SC error occurs.

002

Reboot Type

[0 to 1 / 0 / 1]

0: Manual reboot, 1: Automatic reboot

5878

Option Setup

001

Data Overwrite Security

Press [Execute] to initialize the Data Overwrite Security option for the copier. For more, see "DataOverwriteSecurity Unit" in the chapter "Installation".

5881

Fixed Phase Block Erasing

Detects the Fixed phrase.

5885*

Set WIM Function

020

DocSvr Acc Ctrl

Allows or disallows the functions of web image monitor.

0: OFF, 1: ON

Bit:

0: Forbid all document server access 1: Forbid user mode access

2: Forbid print function 3: Forbid Fax

4: Forbid scan sending 5: Forbid download

6: Forbid delete

7: Forbid guest user

050

DocSvr Format

Selects the display type for the document box list. [0 to 2 / 0 / 1]

0: Thumbnail, 1: Icon, 2: Details

051

DocSvr Trans

Sets the number of documents to be displayed in the document box list. [5 to 20 / 10 / 1]

100

Set Signature

[0 to 2 / 0 / 1/step]

0: Signature for each e-mail 1: Signature for all e-mails 2: No signature

Selects whether the signature is added to the scanned documents with the WIM when they are transmitted by an e-mail.

101

Set Encryption

Determines whether the scanned documents with the WIM are encrypted when they are transmitted by an e-mail.

[0 to 1 / 0 / 1]

0: Not encrypted, 1:Encryption

200

Detect Mem Leak

Not used

201

DocSvr Timeout

Not used

5887

SD Get Counter

This SP determines whether the ROM can be updated.

001

This SP sends a text file to an SD card inserted in SD card Slot 2 (lower slot). The operation stores. The file is stored in a folder created in the root directory of the SD card called SD_COUNTER. The file is saved as a text file (*.txt) prefixed with the number of the machine.

1. Insert the SD card in SD card Slot 2 (lower slot).

2. Select SP5887 then touch [EXECUTE].

Touch [Execute] in the message when you are prompted.

5888*

Personal Information Protect

Selects the protection level for logs. [0 to 1 / 0 / 1]

0: No authentication, No protection for logs

1: No authentication, Protected logs (only an administrator can see the logs)

5893

SDK Application Counter

Displays the counter name of each SDK application.

001

SDK-1

002

SDK-2

003

SDK-3

004

SDK-4

005

SDK-5

006

SDK-6

5907

Plug & Play Maker/Model Name

Selects the brand name and the production name for Windows Plug & Play. This information is stored in the NVRAM. If the NVRAM is defective, these names should be registered again.

After selecting, press the "Original Type" key and "#" key at the same time. When the setting is completed, the beeper sounds five times.

5908*

LCT Paper Size

Specifies the paper size in the LCT. [0 or 1 / 0 / -]

0: A4

1: LT