Reply to thread

Message: <blockquote data-quote="John" data-source="post: 36" data-attributes="member: 2"><p>[4041] User authentication error</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>User authentication error</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Perform the authentication or register as a user, and then perform the printing again.</li> </ul> </td></tr></table><p></p><p></p><p>[4042] Department authentication error</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Department authentication error</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Check department information registered in this equipment.</li> </ul> </td></tr></table><p></p><p></p><p>[4050] Problem in LDAP server connection or LDAP server authorization settings</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Problem in LDAP server connection or LDAP server authorization settings</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Confirm the administrator for the LDAP server connection or LDAP server authorization settings.</li> </ul> </td></tr></table><p></p><p></p><p>[4111] Quota over error (The number of the assigned pages set by department and user management has reached 0.)</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Printer function error</td><td>Quota over error (The number of the assigned pages set by department and user management has reached 0.)</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">The number of the assigned pages set by the department and the number of those assigned by user management have both reached 0. Assign the number of the pages again or perform initialization.</li> </ul> </td></tr></table><p></p><p></p><p>[4112] Quota over error (The number of the assigned pages set by user management has reached 0.</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Printer function error</td><td>Quota over error (The number of the assigned pages set by user management has reached 0.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">The number of the assigned pages set by the user management has reached 0. Assign the number of the pages again or perform initialization.</li> </ul> </td></tr></table><p>[4113] Quota over error (The number of the assigned pages set by department management has reached 0.</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Printer function error</td><td>Quota over error (The number of the assigned pages set by department management has reached 0.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">The number of the assigned pages set by the department management has reached 0. Assign the number of the pages again or perform initialization.</li> </ul> </td></tr></table><p></p><p></p><p>[4121]Job canceling due to external counter error</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Job canceling due to external counter error</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ol> <li data-xf-list-type="ol">Drop a coin in. Perform the print job in error again.</li> <li data-xf-list-type="ol">Insert a key card and then perform the print job in error again, or consult your administrator.</li> <li data-xf-list-type="ol">Insert a key copy counter and then perform the print job in error again.</li> <li data-xf-list-type="ol">Reset the scheduled print job and then perform the print job in error again.</li> </ol> </td></tr></table><p></p><p></p><p></p><p></p><p>8</p><p></p><p></p><p></p><p>[4214] Fax/Internet Fax transmission limitation error</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Fax/Internet Fax transmission limitation error</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Check the settings of this equipment.</li> </ul> </td></tr></table><p></p><p></p><p>[4241] No Printer kit / Printer function disabled</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Printer function error</td><td>Printing functions are disabled since the Printer kit or Printer/ Scanner kit is not installed firmly</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Check that the Printer kit or Printer/Scanner kit is installed firmly.</li> </ul> </td></tr></table><p></p><p></p><p>[4242] No Scanner kit / Scanner function disabled</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Scanner function error</td><td>Internet FAX or storing to a share folder function using a network fax driver is disabled since the Scanner kit is not installed firmly, but the Printer kit is installed.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Check that the Scanner kit is installed firmly.</li> </ul> </td></tr></table><p>[4300] Job execution error due to functional restrictions</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Job execution error due to functional restrictions</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">USB direct printing cannot be performed because the function is restricted by the self-diagnosis. Check the self- diagnosis setting.</li> </ul> </td></tr></table><p></p><p></p><p>[4301] File conversion error</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Printing a file whose format is not supported, or an invalid file</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">The format of this file (other than PDF and JPEG) is not supported in USB direct printing, or the file is invalid. Check the file.</li> </ul> </td></tr></table><p></p><p></p><p>[4311] Not being authorized to perform JOB</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Not being authorized to perform JOB</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Confirm the administrator for the JOB authorization.</li> </ul> </td></tr></table><p></p><p></p><p>[4312] Not authorized to store a file</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Not authorized to store a file</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">The user has not been authorized to perform this operation. Ask your administrator.</li> </ul> </td></tr></table><p></p><p></p><p>[4313] No privilege for e-Filing storage</p><p></p><p>[4314] No privilege for Fax / Internet FAX transmission</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>No privilege for e-Filing storage<br /> No privilege for Fax / Internet FAX transmission</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Check the privilege given, or request the administrator to add the necessary privilege.</li> </ul> </td></tr></table><p>[4411] Image data creation failure)</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Image data creation failure)</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the file to be printed is broken. Perform printing again or use another printer driver.<br /> <ul> <li data-xf-list-type="ul">Network print: Perform the print job in error again, or use another printer driver (e.g.; PS3, Universal).</li> <li data-xf-list-type="ul">Direct print: Check if the file is corrupted (e.g. checking if the file is displayed on your PC monitor), or check if the file format is supported by this equipment.</li> </ul> </td></tr></table><p></p><p></p><p>[4412] Double-sign encoding error</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Double-sign encoding error</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Printing using this function cannot be performed due to a decoding process error which occurs because the PDF file is encrypted incorrectly or encrypted in a language not supported.</li> </ul> </td></tr></table><p></p><p></p><p></p><p></p><p>8</p><p></p><p></p><p></p><p>[4611] Font download failure (reached the registration limit) [4612] Font download failure (HDD full)</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Font download failure (reached the registration limit) Font download failure (HDD full)</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Delete one or more font already registered.</li> </ul> </td></tr></table><p></p><p></p><p>[4613] Font download failure (others)</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Font download failure (others)</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Reattempt the downloading. Recreate font data and reattempt the downloading.</li> </ul> </td></tr></table><p></p><p></p><p>[4621] Font deletion failure</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Font deletion failure</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ul> <li data-xf-list-type="ul">Check if the font to be deleted is registered (or pre- registered) in this equipment.</li> </ul> </td></tr></table><p>[4F10] System abnormality</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Printing was not performed successfully due to other abnormalities.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td> <ol> <li data-xf-list-type="ol">Perform the job in error again. If the error still occurs, turn the power OFF and then back ON, and perform the job again.</li> <li data-xf-list-type="ol">Collect the debug log with USB media.</li> <li data-xf-list-type="ol">Initialize HDD.</li> </ol>  P. 8-3 "8.1.2 Collection of debug logs with a USB device"<br /> Refer to step 3 and later in [E]Replace / Format HDDin<br />  P. 9-19 "9.3.3 Precautions and procedures when replacing the HDD".</td></tr></table><p></p><p></p><p>e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING</p><p></p><ol style="margin-left: 20px" style="margin-left: 20px"> <li data-xf-list-type="ol"> <h3>TopAccess related error</h3> [5010] Internal setting error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>There is a print job, a proof print job, a private print job, a print job without a set department code, a scan job or a fax job remaining in this equipment.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Delete the remaining jobs.<br /> Turn the power OFF and then back ON. Until the initial registration is begun, do not press any button on the control panel or start any print or fax job.</td></tr></table> <br /> <br /> 8<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>A temporary password downloaded from e-Bridge and entered in this equipment is not valid, or the permanent password set in the e-Bridge is not valid.</td></tr></table> <br /> [5012] Authentication error<br /> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Confirm the user name and tentative password.</td></tr></table> <br /> [5013] e-Bridge communication error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>Communication is attempted while the e-Bridge is enabled for some reason such as version upgrade.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the MFP is connected to the eBR2 server.</td></tr></table> <br /> [5014] No SSL certificate<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>There is no SSL certificate or the certificate is not in a correct file format.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Install the correct SSL certificate.</td></tr></table> <br /> © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING<br /> [5015] Invalid SSL certificate<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>SSL certificate is not valid.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Install the correct SSL certificate.</td></tr></table> <br /> [5016] Expired SSL certificate<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>SSL certificate is expired.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Set the correct time.</td></tr></table> <br /> [5017] Other SSL certificate related error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>SSL certificate is invalid.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Install the correct SSL certificate.</td></tr></table> <br /> [5018] Invalid DNS error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>DNS address is invalid.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Set the correct DNS address.<br /> If any setting is needed in DNS, consult your administrators.</td></tr></table> <br /> [5019] Connection error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>Settings for initial URL and proxy are incorrect.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform the correct settings for initial URL and proxy.</td></tr></table> <br /> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING<br /> [501A] Proxy error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>IP address or port for proxy setting is invalid.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Set the correct IP address or port for the proxy setting.<br /> If any setting is needed in proxy, consult your administrators.</td></tr></table> <br /> [501B] No URL (host/port) or invalid path<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>Initial URL is invalid.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Set the correct initial URL.</td></tr></table> <br /> <br /> 8<br /> <br /> [5030] HTTP communication error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Communication error with external application</td><td>An error in the HTTP communication</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the URL for communication.<br /> Check that the valid IP address is assigned to connect to the server.</td></tr></table> <br /> [50FF] eBR2 internal error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP internal error</td><td>A fatal error occurred in the MFP</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Restart the MFP, and then try again.</td></tr></table> <br /> [5110] Toner cartridge detection error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Toner cartridge detection error.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td></td></tr></table> <ul> <li data-xf-list-type="ul">Check if the toner cartridge is installed properly.</li> <li data-xf-list-type="ul">Check if the toner cartridge detection sensor operates properly.<br /> </li> </ul>© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING<br /> [5BD0] Power failure during restoration<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Power supply is cut off during the restoration of database sent from TopAccess</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td></td></tr></table> <ul> <li data-xf-list-type="ul">Check if the power cable is connected properly and is inserted securely.</li> <li data-xf-list-type="ul">Check if the power voltage is unstable.</li> <li data-xf-list-type="ul">Reattempt the restoration of the database (Address Book, templates, F-code (Mailbox) or user information).<br /> </li> </ul>[5C10] FAX Unit attachment error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Network FAX is disabled because the FAX Unit is not attached</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td></td></tr></table> <ul> <li data-xf-list-type="ul">Check if the FAX Unit is attached.</li> <li data-xf-list-type="ul">Check if there is any damage or abnormality on the FAX board.</li> <li data-xf-list-type="ul">Check if the connector on the FAX board is connected properly.<br /> </li> </ul>[5C11] Network FAX transmission error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>The network FAX job failed because the specified address is not registered in the Address Book</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>The address specified for the network FAX is not registered on the Address Book. Register it.</td></tr></table> <br /> [5C20] Data import from TopAccess succeeded<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Displayed when data have been imported from TopAccess (Not an error message)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Data (Address book, department or user information) have been imported successfully. No troubleshooting is required.</td></tr></table> <br /> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING<br /> <br /> 8<br /> <br /> [5C21] Error in data import from TopAccess<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>TopAccess related error</td><td>Data import from TopAccess failed due to invalid file format</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Data import failed because the specified file (Address Book, department or user information) is incorrect or damaged. Check if the file is incorrect or damaged, and then reattempt the import.</td></tr></table> <br /> © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING</li> <li data-xf-list-type="ol"> <h3>MFP access error</h3> [6007] Unsuccessful User Login to MFP<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>User authentication cannot be done because connection to the authentication server has failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the operating status of the server and connection from an MFP have been confirmed.</td></tr></table> <br /> [6008] Failed to connect on External Role Base Access Control (LDAP) Server<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>User authentication cannot be done because connection to an external RBAC server has failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the operating status of the server and connection from the MFP have been confirmed.</td></tr></table> <br /> [6013] Connection failure to the authentication server<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Failed to connect to the authentication server</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check that the server setting is proper by accessing [TopAccess] -> [Administration] -> [Maintenance] -> [Directory Service].<br /> When “Auto” is selected as the authentication method, this error may output to the log depending on the environment.</td></tr></table> <br /> [6014] The authentication server that cannot be accessed is detected<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>The authentication server that cannot be accessed is detected</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the authentication server is down since the access to the authentication server is not available. The unavailable authentication server is accessed again if the time set in 08- 8788 passes or the power of the equipment is turned OFF and back ON.</td></tr></table> <br /> [6032] Card related error: Expired card<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>The card cannot be used because it has expired.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Use a card with a valid expiration.</td></tr></table> <br /> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING<br /> [6033] Card related error: Invalid flag data (no room-entry data)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>The card cannot be used because no room-entry data are recorded in it.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Use a correct card that has been used for entering the room.</td></tr></table> <br /> [6034] Card related error: Invalid flag data (invalid card data)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>The card cannot be used because the data required for the use of the card are not correctly set.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Use a valid card.</td></tr></table> <br /> <br /> 8<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>The equipment or device cannot be used since no privilege is given.</td></tr></table> <br /> [6037] Flags not available<br /> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Use the enable card or contact your administrator.</td></tr></table> <br /> [6041] Card authentication: Card related error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>The self-diagnostic code required for card authentication is not set in this equipment correctly.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Reattempt scanning. If the error still occurs after reattempting scanning for several times, card data may be corrupted or the card reader may be out of order.</td></tr></table> <br /> [6042] Card authentication: Card setting error<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>The self-diagnostic code required for card authentication is not set in this equipment correctly.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>MFP access error</td><td>Set the correct self-diagnostic code.</td></tr></table> <br /> [6100] User account locking out<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>User account is locked</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Log into TopAccess as an administrator, and release the locked user account.</td></tr></table> <br /> © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING<br /> [6101] e-Filing box locking out<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>The e-Filing Box became inaccessible because an incorrect password has been entered for the specified number of times.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Retry access after a few minutes. For the locking period, ask your administrator.</td></tr></table> <br /> [6102] User account being locking out<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Failed to login because the user account had been locked out</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Log into TopAccess as an administrator, and release the locked user account.</td></tr></table> <br /> [6103] e-Filing Box is locked out<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>The e-Filing Box became inaccessible because an incorrect password has been entered for the specified number of times.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Retry access after a few minutes. For the locking period, ask your administrator.</td></tr></table> <br /> [6121] Automatic Secure Erase failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>The automatic secure erase fails.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Data overwriting failed for some reason. If the error still occurs after rebooting the equipment, start up using the following procedure:[3] + [C] + [START]  3. HDD formatting<br />  Reinstallation of software or HDD replacement</td></tr></table> <br /> [6131] Clock skew failure to time server<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Clock skew failure to time server</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check that the time server works properly. Moreover, log into TopAccess as an administrator, and check that the SNTP setting is correct.</td></tr></table> <br /> [6150] Print log DB full<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Print log DB full</td></tr></table> <br /> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING<br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Print Job Log Export.</td></tr></table> <br /> [6151] Print log DB near-full (95%<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Print log DB near-full (95%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Print Job Log Export.</td></tr></table> <br /> [6152] Print log DB near-full (90%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Print log DB near-full (90%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Print Job Log Export.</td></tr></table> <br /> <br /> 8<br /> <br /> [6153] Print log DB near-full (80%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Print log DB near-full (80%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Print Job Log Export.</td></tr></table> <br /> [6154] Print log database near-full (70%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Print log DB near-full (70%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Print Job Log Export.</td></tr></table> <br /> [6160] Scan log DB full<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Scan log DB full</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Scan Job Log Export.</td></tr></table> <br /> [6161] Scan log DB near-full (95%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Scan log DB near-full (95%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Scan Job Log Export.</td></tr></table> <br /> © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING<br /> [6162] Scan log DB near-full (90%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Scan log DB near-full (90%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Scan Job Log Export.</td></tr></table> <br /> [6163] Scan log DB near-full (80%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Scan log DB near-full (80%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Scan Job Log Export.</td></tr></table> <br /> [6164] Scan log DB near-full (70%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Scan log DB near-full (70%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Scan Job Log Export.</td></tr></table> <br /> [6170] FAX transmission log DB full<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>FAX transmission log DB full</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Fax Transmission Journal Export.</td></tr></table> <br /> [6171] FAX transmission log DB near-full (95%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>FAX transmission log DB near-full (95%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Fax Transmission Journal Export.</td></tr></table> <br /> [6172] FAX transmission log DB near-full (90%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>FAX transmission log DB near-full (90%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Fax Transmission Journal Export.</td></tr></table> <br /> [6173] FAX transmission log DB near-full (80%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>FAX transmission log DB near-full (80%)</td></tr></table> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING<br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Fax Transmission Journal Export.</td></tr></table> <br /> [6174] FAX transmission log DB near-full (70%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>FAX transmission log DB near-full (70%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Fax Transmission Journal Export.</td></tr></table> <br /> [6180] FAX reception log DB full<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>FAX reception log DB full</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Fax Reception Journal Export.</td></tr></table> <br /> <br /> 8<br /> <br /> [6181] FAX reception log DB near-full (95%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>FAX reception log DB near-full (95%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Fax Reception Journal Export.</td></tr></table> <br /> [6182] FAX reception log DB near-full (90%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>FAX reception log DB near-full (90%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Fax Reception Journal Export.</td></tr></table> <br /> [6183] FAX reception log DB near-full (80%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>FAX reception log DB near-full (80%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Fax Reception Journal Export.</td></tr></table> <br /> [6184] FAX reception log DB near-full (70%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>FAX reception log DB near-full (70%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Fax Reception Journal Export.</td></tr></table> © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING<br /> [6190] Message log DB full<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Message log DB full</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Message Log Export.</td></tr></table> <br /> [6191] Message log DB near-full (95%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Message log DB near-full (95%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Message Log Export.</td></tr></table> <br /> [6192] Message log DB near-full (90%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Message log DB near-full (90%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Message Log Export.</td></tr></table> <br /> [6193] Message log DB near-full (80%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Message log DB near-full (80%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Message Log Export.</td></tr></table> <br /> [6194] Message log DB near-full (70%)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>MFP access error</td><td>Message log DB near-full (70%)</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Perform Clear Log with TopAccess Logs>Export Logs>Message Log Export.</td></tr></table> <br /> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING</li> <li data-xf-list-type="ol"> <h3>Maintenance error</h3> [7101] System firmware installation failure [7103] Engine firmware installation failure [7105] Scanner firmware installation failure [7107] MEP firmware installation failure [7111] Patch installation failure<br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>System firmware installation failed. ([7101]) Engine firmware installation failed. ([7103]) Scanner firmware installation failed. ([7105]) MEP firmware installation failed. ([7107]) Patch installation failed. ([7111])<br /> Plug-in installation failed. ([7113]) HDD data installation failed. ([7115]) DF firmware installation failed. ([7117])</td></tr></table> <br /> [7113] Plug-in installation failure [7115] HDD data installation failure [7117] DF firmware installation failure<br /> <br /> <br /> 8<br /> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Software package file may have a problem or may be corrupted. Check the software package file and then reattempt the installation.</td></tr></table> <br /> [7109] Printer driver update failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Printer driver upload failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Printer driver file may have a problem or may be corrupted. Check the package file and then reattempt the upload.</td></tr></table> <br /> [710B] Point and Print data installation failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Point and Print data upload failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Point and Print data may have a problem or may be corrupted. Check the package file and then reattempt the upload.</td></tr></table> <br /> [710F] Language Pack installation failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Language Pack installation failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Language Pack file may have a problem or may be corrupted. Check the package file and then reattempt the installation.</td></tr></table> © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING<br /> [711D] License key returning failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The one-time dongle license fails to be returned to USB media.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Return the license to the USB media used for installing the license.<br /> Check that the USB media is correctly installed.<br /> Notes:<br /> The GP-1080 IPSec Enabler cannot return to the USB media due to license problem.<br /> The GP-1070 Overwrite Enabler cannot return to the USB media in the high security (08-8911: 3).</td></tr></table> <br /> [711F] License key installation failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The one-time dongle license fails to be installed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check that the USB media is correctly installed.</td></tr></table> <br /> [7121] Unsuccessful Import of Address Book Data<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of Address Book data failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> [7123] Unsuccessful Import of Template Data<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of template data failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> [7125] Unsuccessful Import of MailBox Data<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of Mailbox data failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING<br /> [7127] Unsuccessful Import of Format File for Metascan<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of Meta Scan format file failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> [7129] Unsuccessful Import of User Information<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of user information failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> <br /> 8<br /> <br /> [712B] Unsuccessful Import of Role Information<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of role information failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> [712D] Unsuccessful Import of Department Data<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of department data failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> [712F] Unsuccessful Import of ICC Profile<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of ICC Profile failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> [7131] Failed to import Print Data Converter<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of Print Data Converter failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING<br /> [7132] Failed to import any users<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>A part of the user information was not imported.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>There is a possibility that the amount of user information has exceeded the maximum for registration during the import or the file contains invalid data. Check if you are importing a valid file and also that the amount of user information does not exceed the maximum.</td></tr></table> <br /> [7133] Failed to import any user, role and group information<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>A part of the user, role or group information was not imported.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>There is a possibility that the amount of the combined user information has exceeded the maximum for registration during the import or the file contains invalid data. Check if you are importing a valid file and also that the amount of the combined user information does not exceed the maximum.</td></tr></table> <br /> [7134] Department data import partial failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>A part of the department data was not imported.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>There is a possibility that the amount of department data has exceeded the maximum for registration during the import or the file contains invalid data. Check if you are importing a valid file and also that the amount of department data does not exceed the maximum.</td></tr></table> <br /> [7139] Unsuccessful Acquisition of Certificate from SCEP Server<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Failed to import the certificate by SCEP</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the SCEP server and the SCEP setting (automatic) in TopAccess Administration>Security>Certificate Management.</td></tr></table> <br /> [713B] Unsuccessful Import of Certificate from TopAccess<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Failed to import the certificate</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Certificate may have a problem or be corrupted. Check the certificate and perform the job again.</td></tr></table> <br /> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING<br /> [713D] Unsuccessful Import of User Combined Data<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of combined user information failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> [713F] Unsuccessful Import of All Data (Template/AddressBook/MailBox)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of all data (templates, Address Book, Mailbox) failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if you are importing a valid file.</td></tr></table> <br /> <br /> 8<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of Address Book data failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> [7141] Unsuccessful Export of Address Book Data<br /> <br /> [7143] Unsuccessful Export of Template Data<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of template data failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> [7145] Unsuccessful Export of MailBox Data<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of Mailbox data failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> [7147] Unsuccessful Export of Format File for Metascan<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of a Meta Scan format file failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING<br /> [7149] Unsuccessful Export of User Information<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of user information failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> [714B] Unsuccessful Export of Role Information<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of role information failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> [714D] Unsuccessful Export of Department Information<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of department data failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> [714F] Unsuccessful Export of ICC Profile<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of ICC Profile failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> [7151] Unsuccessful Export of Log Data<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of log data failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and the USB media and then retry the export.</td></tr></table> <br /> [715B] Unsuccessful Print Data Converter<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of Print Data Converter failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING<br /> [715D] Unsuccessful export of User Combined Data<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of combined user information failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> [715F] Unsuccessful Export of All Data (Template/AddressBook/MailBox)<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The export of all data (templates, Address Book, Mailbox) failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and then retry the export.</td></tr></table> <br /> <br /> 8<br /> <br /> [7191] DDNS public key file upload failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Failed to upload DDNS public key file</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>DDNS public key file may have a problem or be corrupted. Check the file and perform the job again.</td></tr></table> <br /> [7193] DDNS private key file upload failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Failed to upload DDNS private key file</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>DDNS private key file may have a problem or be corrupted. Check the file and perform the job again.</td></tr></table> <br /> [71A2] Unsuccessful Addition of CA Certificate<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Failed to add CA certificate</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>CA certificate may have a problem or be corrupted. Check the CA certificate and perform the job again.</td></tr></table> <br /> © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING<br /> [71A4] Cryptographic key consistency confirmation failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Cryptographic key consistency confirmation failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Start up the equipment in the following procedure:[3] + [C] + [START]  5. Key Backup Restore Then overwrite the corrupted license key with a normal one.</td></tr></table> <br /> [71A6] Device certificate deletion failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The deletion of device certificate failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Restart the equipment and then retry.</td></tr></table> <br /> [71A8] CA certificate deletion failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The deletion of the CA certificate failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Restart the equipment and then retry.</td></tr></table> <br /> [71AA] Unidentified error during certificate acquisition from SCEP server<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Unidentified error occurred during certificate acquisition from SCEP server.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check SCEP server and the SCEP setting (automatic) on the TopAccess screen as follows: TopAccess Administration  Security  Certificate Management</td></tr></table> <br /> [71AB] Timeout error during certificate acquisition from SCEP server<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Timeout error occurred during certificate acquisition from SCEP server.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check SCEP server and the SCEP setting (automatic) on the TopAccess screen in the following procedure: TopAccess Administration  Security  Certificate Management</td></tr></table> <br /> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING<br /> [71AC] File save error during certificate acquisition from SCEP server<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>File save error occurred during certificate acquisition from SCEP server.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>File saving failed for some reason. If the error still occurs after rebooting the equipment, start up using the following procedure:[3] + [C] + [START]  3. HDD formatting  Reinstallation of software or HDD replacement</td></tr></table> <br /> [71AD] Failed SCEP operation<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>SCEP operation is failed</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check SCEP server and the SCEP setting on the TopAccess menu as follows:<br /> [Administration] > [Security] > [Certificate Management] > SCEP (Automatic)</td></tr></table> <br /> <br /> 8<br /> <br /> [71B0] Software package file decryption failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Software package file decryption failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Software package file may have a problem or may be corrupted. Check the software package file and then reattempt the installation.</td></tr></table> <br /> [71D0] Factory Default Failure<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>Factory default setting failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Restart the equipment and then retry.</td></tr></table> <br /> [71F1] Unsuccessful Creation of Clone File<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The creation of a clone file failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is enough capacity in the HDD and the USB media and then retry the creation.</td></tr></table> <br /> © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507<br /> ERROR CODE AND TROUBLESHOOTING<br /> [71F3] Unsuccessful Import of Clone Data<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The import of clone data failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>The clone file may be invalid. Check the file and then retry the import.</td></tr></table> <br /> [71F4] Failed to decrypt Clone file<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The decryption of a clone file failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>The clone file may be invalid or the password may be incorrect. Check the file and the password, and then retry the import.</td></tr></table> <br /> [71F5] Failed to encrypt Clone file<br /> <br /> <table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Maintenance error</td><td>The encryption of a clone file failed.</td></tr></table> <br /> <table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Restart the equipment and then retry the encryption.</td></tr></table> <br /> e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING</li> <li data-xf-list-type="ol"> <h3>Network error</h3> </li> </ol><p>[8000] Static IPv4 address conflict</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>IPv4 address overlaps.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the same IP address is not used by other machine.</td></tr></table><p></p><p></p><p>[8011] Linklocal Address Conflict</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Linklocal Address Conflict</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the same IP address is not used by other machine.</td></tr></table><p></p><p></p><p></p><p></p><p>8</p><p></p><p></p><p></p><p>[8012] Manual Address Conflict</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Manual IPv6 Address Conflict</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the same IP address is not used by other machine.</td></tr></table><p></p><p></p><p>[8013] Stateless Address Conflict</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Stateless Address Conflict</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the same IP address is not used by other machine.</td></tr></table><p></p><p></p><p>[8014] Stateful Address Conflict</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Stateful Address Conflict</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the same IP address is not used by other machine.</td></tr></table><p></p><p></p><p>[8022] Authentication Failure</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Failed in 802.1X authentication.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the user credential.</td></tr></table><p></p><p></p><p>[8023] Can not contact Authentication Server/Switch</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Failed in connection to authentication server and switch.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check connectivity to switch or server.</td></tr></table><p></p><p></p><p>© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507</p><p></p><p>ERROR CODE AND TROUBLESHOOTING</p><p></p><p>[8024] Certificate verification Failure</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Failed in verification of certificate.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if a valid certificate is installed.</td></tr></table><p></p><p></p><p>[8031] IKEv1 certification failed</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for ikev1 certification failed</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check<br /> <ol> <li data-xf-list-type="ol">CA and user certificate in both MFP and remote peer - certificate timestamp and IPsec Certificate template should be valid.</li> <li data-xf-list-type="ol">CRL DP server name is mapped in MFP’s host table or DNS entry.</li> <li data-xf-list-type="ol">Certificate against CRL.</li> </ol> </td></tr></table><p></p><p></p><p>[8032] IKEv1 wrong proposal chosen</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for wrong proposal chosen</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the IKEv1 IPsec proposal parameters (like encryption/ authentication algorithms, DH group, authentication methods) in MFP and peer machine.</td></tr></table><p></p><p></p><p>[8033] IKEv1 shared key authentication failed</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error if auth for shared key failed</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Mismatch in IKEv1 Pre Shared Key. Check the PSK in MFP and remote machine.</td></tr></table><p></p><p></p><p>[8034] IKEv1 invalid certificate</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error if invalid certificate uploaded</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the CA and User certificate in MFP and peer machine.</td></tr></table><p></p><p></p><p>[8035] IKEv1 certificate not supported</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error if certificate not supported</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the User certificate type.</td></tr></table><p></p><p></p><p>e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING</p><p></p><p>[8036] IKEv1 invalid certificate authentication</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error if invalid certificate authentication</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the CA certificate in MFP and Peer machine.</td></tr></table><p></p><p></p><p>[8037] IKEv1 certificate unavailable</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error if certificate are not available</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Certificate has been deleted from Certificate store. Re-upload the corresponding certificates.</td></tr></table><p></p><p></p><p></p><p></p><p>8</p><p></p><p></p><p></p><p>[8038] IKEv1 no SA established</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for SA is not present</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the IKEv1/IPsec proposal parameters (like encryption/ authentication algorithms, DH group, authentication methods) in MFP and peer machine.<br /> Check<br /> 1. CA and user certificate in both MFP and remote peer - certificate timestamp and IPsec Certificate template.</td></tr></table><p></p><p></p><p>[8039] IKEv1 invalid signature</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for invalid signature for certificate</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Mismatch in Signature payload (MAC or IV).<br /> Check the CA and user certificate in MFP and peer machine.</td></tr></table><p></p><p></p><p>[803A] IKEv2 wrong proposal chosen</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error if proposal chosen is wrong</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the IKEv2/IPsec proposal parameters (encryption/ authentication algorithms, DH group, authentication methods) in MFP and peer machine.</td></tr></table><p></p><p></p><p>© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507</p><p></p><p>ERROR CODE AND TROUBLESHOOTING</p><p></p><p>[803B] IKEv2 Certificate failed</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for ikev2 certification failed</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check<br /> <ol> <li data-xf-list-type="ol">CA and user certificate in both MFP and remote peer - certificate timestamp and IPsec Certificate template should be valid.</li> <li data-xf-list-type="ol">CRL DP server name is mapped in MFP’s host table or DNS entry.</li> <li data-xf-list-type="ol">Certificate against CRL.</li> </ol> </td></tr></table><p></p><p></p><p>[803C] IKEv2 secret key authentication failed</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for ikev2 if secret key auth failed</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Mismatch in IKEv2 Pre Shared Key. Check the PSK in MFP and peer machine.</td></tr></table><p></p><p></p><p>[803D] IKEv2 falling back to IKEv1</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error if peer does not support IKEv2 and falling back to IKEv1</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Remote machine is not supporting IKEv2. Going back to use IKEv1.</td></tr></table><p></p><p></p><p>[803E] IKEv2 ISAKMP SA unavailable</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error if ISAKMP SA is not created of destroyed due to some uncertain condition</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Restart IPsec service on Peer and retry.</td></tr></table><p></p><p></p><p>[803F] IKEv2 cryptographic operation failed</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for ikev2 if crypto operation failed</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>If Certificates are being used, re-upload the corresponding certificates using Security Services. Restart IPsec Service on MFP.</td></tr></table><p></p><p></p><p>e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING</p><p></p><p>[8040] IKEv2 invalid key information</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for ikev2 if key info is invalid</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check IKE settings in MFP and peer.</td></tr></table><p></p><p></p><p>[8041] IKEv2 CA not trusted</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for ikev2 if CA is not trusted</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the CA certificate in MFP and peer machine. Check the CA certificate timestamp.</td></tr></table><p></p><p></p><p></p><p></p><p>8</p><p></p><p></p><p></p><p>[8042] IKEv2 Authentication method mismatch</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error if authentication method is not matching</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Mismatch in IKE authentication type.<br /> Check the Authentication type in MFP and peer.</td></tr></table><p></p><p></p><p>[8043] IPsec IKE version mismatch</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error if ike version is not matching</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Mismatch in IKE version.<br /> Check the IKE version in MFP and peer.</td></tr></table><p></p><p></p><p>[8044] IPsec encapsulation mismatch</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for encapsulation is not matching</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the IPsec mode (Transport/Tunnel) in MFP and peer.</td></tr></table><p></p><p></p><p>[8045] IPsec Peer IP mismatch</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for peer ip mismatch</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Remote Traffic selector mismatch.<br /> Check the destination address/port in IPsec filter.</td></tr></table><p></p><p></p><p>© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507</p><p></p><p>ERROR CODE AND TROUBLESHOOTING</p><p></p><p>[8046] IPsec local IP mismatch</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for local ip mismatch</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Local traffic selector mismatch.<br /> Check the source address/port in IPsec filter.</td></tr></table><p></p><p></p><p>[8047] IPsec local ID mismatch</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for local id mismatch</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the user certificate in MFP</td></tr></table><p></p><p></p><p>[8048] IPsec Remote ID mismatch</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for remote id mismatch</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the user certificate in peer machine.</td></tr></table><p></p><p></p><p>[8049] IPsec Remote IP mismatch</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for remote ip mismatch</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Remote traffic selector mismatch.<br /> Check the source address/port in IPsec filter.</td></tr></table><p></p><p></p><p>[804A] IPsec IKE timeout</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error for ike timeout</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the network connectivity between MFP and peer machine.<br /> Select the Flush Connections Option and retry.</td></tr></table><p></p><p></p><p>[804B] IPSec invalid manual key</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Ipsec error id manual key is not valid</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the Inbound and Outbound (ESP Encryption/ Authentication and AH Authentication) keys in MFP and Remote PC.</td></tr></table><p></p><p></p><p>e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING</p><p></p><p>[8061] Secure primary DDNS update error [8062] Secure secondary DDNS update error [8063] IPv6 Secure primary DDNS update error</p><p></p><p>[8064] IPv6 Secure secondary DDNS update error [8065] IPv6 primary DDNS update error</p><p></p><p>[8066] IPv6 secondary DDNS update error [8067] IPv4 primary DDNS update error [8068] IPv4 secondary DDNS update error</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Secure update to primary IPv4 server failed. ([8061]) Secure update to secondary IPv4 server failed. ([8062]) Secure update to primary IPv6 server failed. ([8063]) Secure update to secondary IPv6 server failed. ([8064]) IPv6 primary DDNS update error. ([8065])<br /> IPv6 secondary DDNS update error. ([8066]) IPv4 primary DDNS update error. ([8067]) IPv4 secondary DDNS update error. ([8068])</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is any problem with DNS or DDNS settings.</td></tr></table><p></p><p></p><p></p><p></p><p>8</p><p></p><p></p><p></p><p>[8069] Invalid TSIG/SIG(0) Key file</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>This message is displayed when the key file for SIG(0) or TSIG is invalid.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Verify the TSIG/SIG(0) key files used.</td></tr></table><p></p><p></p><p>[8101] Wireless association with Access point failure</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Wireless association with Access point failure</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Verify the credentials used for association with Access point.</td></tr></table><p></p><p></p><p>[8102] MFP not able to contact the Access point with the specified SSID</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>MFP not able to contact the Access point with the specified SSID</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Verify the access point name setting and mechanism used for association same as Access Point setting.</td></tr></table><p></p><p></p><p>© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507</p><p></p><p>ERROR CODE AND TROUBLESHOOTING</p><p></p><p>[8103] Wireless Certificate verification failure</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Wireless Certificate verification failure</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Verify the certificate settings used for association.</td></tr></table><p></p><p></p><p>[8111] SNMP writing access failure</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>An error occurred during SNMP data writing.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the parameter entered in the application is correct. Check if the entered department code and box password are correct.<br /> If the error still occurs after the correct parameter is entered, restart the equipment and the application.</td></tr></table><p></p><p></p><p>[8112] SNMP communication failure</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>SNMP communication failed.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if there is any problem in the application.</td></tr></table><p></p><p></p><p>[8121] Domain authentication error: Domain authentication error</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>An unidentified domain authentication error occurred during the connection of domain controller.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the network configuration of this equipment and then reconnect to the domain controller.</td></tr></table><p></p><p></p><p>[8122] Domain authentication error: Invalid user name or password</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Login is not permitted because the user name or a password for domain authentication is invalid.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the user name and the password for this equipment are correct. Specify upper- and lower-case characters correctly when you enter them.</td></tr></table><p></p><p></p><p>e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING</p><p></p><p>[8123] Domain authentication error: Invalid server</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>The server was not discovered during domain authentication.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the server is down or the network configuration of this equipment is correct. If domain name resolution is used, check the DNS and DDNS settings.</td></tr></table><p></p><p></p><p>[8124] Domain authentication error: Invalid user account</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>The user account is invalid and not available for login for domain authentication</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the setting to see if the user account noted in the Active Directory Users and Computers window is valid.</td></tr></table><p></p><p></p><p></p><p></p><p>8</p><p></p><p></p><p></p><p>[8125] Domain authentication error: Expired user account</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>The user account is expired and not available for login for domain authentication.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the setting to see if the user account noted in the Active Directory Users and Computers window is not expired.</td></tr></table><p></p><p></p><p>[8126] Domain authentication error: User account lockout</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>The user account is locked out and not available for login for domain authentication.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the account lockout setting of the server.</td></tr></table><p></p><p></p><p>[8127] Domain authentication error: Invalid logon hours</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>The logon hour is invalid and not available for login for domain<br /> authentication.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check the logon hour setting for the user account noted in the Active Directory Users and Computers window.</td></tr></table><p></p><p></p><p>© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507</p><p></p><p>ERROR CODE AND TROUBLESHOOTING</p><p></p><p>[8128] Active Directory domain authentication error: Time delay between server and equipment</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>There is a difference of 5 minutes or longer between the time settings of this equipment and the server, and therefore the login is not available for Active Directory domain authentication.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Set the time of this equipment and that of the domain controller the same. SNTP is recommended if there is an SNTP server in the network.</td></tr></table><p></p><p></p><p>[8129] Active Directory domain authentication error: Expired Kerberos ticket</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>The Kerberos ticket is expired and not available for login for Active Directory domain authentication.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the Kerberos ticket on the Kerberos server is expired.</td></tr></table><p></p><p></p><p>[812A] Active Directory domain authentication error: Kerberos ticket authentication error</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>Login is not available for Active Directory domain authentication due to a Kerberos ticket authentication error.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the user name and the password for this equipment are correct. If the error still occurs, ask your Windows Server administrator.</td></tr></table><p></p><p></p><p>[812B] Active Directory domain authentication error: invalid realm name</p><p></p><p></p><p></p><table style='width: 100%'><tr><td>Classification</td><td>Error item</td></tr><tr><td>Network error</td><td>The realm name is invalid and not available for login for Active Directory domain authentication.</td></tr></table><p></p><p></p><table style='width: 100%'><tr><td>Check item</td><td>Measures</td></tr><tr><td>Setting</td><td>Check if the realm name of this equipment for the Active Directory server is correct. If the error still occurs, ask your Windows Server administrator.</td></tr></table><p></p><p></p><p>e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507 © 2011-2014 TOSHIBA TEC CORPORATION All rights reserved ERROR CODE AND TROUBLESHOOTING</p><p></p><h3>Output check (test mode 03)</h3><p></p><p></p><table style='width: 100%'><tr><td>Code</td><td>Function</td><td>Procedure</td></tr><tr><td>101</td><td>Main motor ON (operational without developer unit)</td><td>1</td></tr><tr><td>102</td><td>Toner motor ON (normal rotation)</td><td>1</td></tr><tr><td>103</td><td>Polygonal motor ON (600 dpi)</td><td>1</td></tr><tr><td>108</td><td>Registration clutch ON</td><td>1</td></tr><tr><td>109</td><td>PFP motor ON</td><td>1</td></tr><tr><td>110</td><td>ADU motor ON (low speed)</td><td>1</td></tr><tr><td>118</td><td>Laser ON</td><td>1</td></tr><tr><td>120</td><td>Exit motor ON (normal rotation)</td><td>1</td></tr><tr><td>121</td><td>Exit motor ON (reverse rotation)</td><td>1</td></tr><tr><td>122</td><td>LCF motor ON</td><td>1</td></tr><tr><td>123</td><td>Reverse motor ON (normal rotation) * e-STUDIO356/456 only</td><td>1</td></tr><tr><td>124</td><td>Reverse motor ON (reverse rotation) * e-STUDIO356/456 only</td><td>1</td></tr><tr><td>151</td><td>Code No. 101 function OFF</td><td>1</td></tr><tr><td>152</td><td>Code No. 102 function OFF</td><td>1</td></tr><tr><td>153</td><td>Code No. 103 function OFF</td><td>1</td></tr><tr><td>158</td><td>Code No. 108 function OFF</td><td>1</td></tr><tr><td>159</td><td>Code No. 109 function OFF</td><td>1</td></tr><tr><td>160</td><td>Code No. 110 function OFF</td><td>1</td></tr><tr><td>168</td><td>Code No. 118 function OFF</td><td>1</td></tr><tr><td>170</td><td>Code No. 120 function OFF</td><td>1</td></tr><tr><td>171</td><td>Code No. 121 function OFF</td><td>1</td></tr><tr><td>172</td><td>Code No. 122 function OFF</td><td>1</td></tr><tr><td>173</td><td>Code No. 123 function OFF</td><td>1</td></tr><tr><td>174</td><td>Code No. 124 function OFF</td><td>1</td></tr><tr><td>177</td><td>Offset Tray motor ON (reciprocating movement)</td><td>2</td></tr><tr><td>201</td><td>Upper drawer feed clutch ON/OFF</td><td>3</td></tr><tr><td>202</td><td>Lower drawer feed clutch ON/OFF</td><td>3</td></tr><tr><td>203</td><td>Transport clutch (high speed) ON/OFF</td><td>3</td></tr><tr><td>204</td><td>Bypass feed clutch ON/OFF</td><td>3</td></tr><tr><td>205</td><td>Transport clutch (low speed) ON/OFF</td><td>3</td></tr><tr><td>206</td><td>LCF pickup solenoid ON/OFF</td><td>3</td></tr><tr><td><br /> 207</td><td>LCF end fence reciprocating movement<br /> This function is disabled in the following conditions.<br /> <ul> <li data-xf-list-type="ul">When the LCF tray is up.</li> <li data-xf-list-type="ul">When the left drawer is not inserted.</li> <li data-xf-list-type="ul">When the LCF misfeed insertion detection sensor is incorrectly inserted.</li> </ul> </td><td>2</td></tr><tr><td>209</td><td>LCF feed clutch ON/OFF</td><td>3</td></tr><tr><td>218</td><td>Key copy counter count up</td><td>2</td></tr><tr><td>222</td><td>ADU clutch ON/OFF</td><td>3</td></tr><tr><td>225</td><td>PFP transport clutch ON/OFF</td><td>3</td></tr><tr><td>226</td><td>PFP upper drawer feed clutch ON/OFF</td><td>3</td></tr><tr><td>228</td><td>PFP lower drawer feed clutch ON/OFF</td><td>3</td></tr><tr><td>232</td><td>Bridge unit gate solenoid ON/OFF</td><td>3</td></tr><tr><td>233</td><td>Reverse solenoid ON/OFF * e-STUDIO356/456 only</td><td>3</td></tr><tr><td>235</td><td>Discharge lamp ON/OFF</td><td>3</td></tr><tr><td>236</td><td>Suction fan ON/OFF (low speed)</td><td>3</td></tr><tr><td>237</td><td>Suction fan ON/OFF (high speed)</td><td>3</td></tr><tr><td>242</td><td>Upper drawer tray-up motor ON (tray up)</td><td>2</td></tr><tr><td>243</td><td>Lower drawer tray-up motor ON (tray up)</td><td>2</td></tr><tr><td>249</td><td>Developer bias [-DC] ON/OFF</td><td>3</td></tr><tr><td>250</td><td>Developer bias [AC] ON/OFF</td><td>3</td></tr><tr><td>252</td><td>Main charger ON/OFF</td><td>3</td></tr><tr><td>253</td><td>Separation charger ON/OFF</td><td>3</td></tr><tr><td>255</td><td>Transfer guide bias ON/OFF</td><td>3</td></tr><tr><td>256</td><td>Transfer charger (positive/center) ON/OFF</td><td>3</td></tr><tr><td>257</td><td>Transfer charger (positive/high) ON/OFF</td><td>3</td></tr><tr><td>258</td><td>Transfer charger (negative) ON/OFF</td><td>3</td></tr></table> <table style='width: 100%'><tr><td>261</td><td>Scan motor ON (Automatically stops at limit position; speed<br /> can be changed with the [ZOOM] button</td><td>2</td></tr><tr><td>267</td><td>Scanner exposure lamp ON/OFF</td><td>3</td></tr><tr><td>271</td><td>LCF tray-up motor (up/down)</td><td>2</td></tr><tr><td>278</td><td>PFP upper drawer tray-up motor ON (tray up)</td><td>2</td></tr><tr><td>280</td><td>PFP lower drawer tray-up motor ON (tray up)</td><td>2</td></tr><tr><td>281</td><td>RADF feed motor ON/OFF (normal rotation)</td><td>3</td></tr><tr><td>282</td><td>RADF feed motor ON/OFF (reverse rotation)</td><td>3</td></tr><tr><td>283</td><td>RADF read motor ON/OFF (normal rotation)</td><td>3</td></tr><tr><td>284</td><td>RADF exit motor ON/OFF (normal rotation)</td><td>3</td></tr><tr><td>285</td><td>RADF exit motor ON/OFF (reverse rotation)</td><td>3</td></tr><tr><td>289</td><td>Developer cooling fan ON/OFF (high speed)</td><td>3</td></tr><tr><td>290</td><td>Developer cooling fan ON/OFF (low speed)</td><td>3</td></tr><tr><td>294</td><td>Reverse gate solenoid ON/OFF</td><td>3</td></tr><tr><td>295</td><td>Power OFF mode (for 200 V series)</td><td>4</td></tr><tr><td>297</td><td>RADF fan motor ON/OFF</td><td>3</td></tr><tr><td>301</td><td>Modem test 2100Hz</td><td>2</td></tr><tr><td>302</td><td>Modem test 14.4KBPS (V17)</td><td>2</td></tr><tr><td>303</td><td>Modem test 9.6KBPS (V29)</td><td>2</td></tr><tr><td>304</td><td>Modem test 4.8KBPS (V27)</td><td>2</td></tr><tr><td>305</td><td>Modem test 300BPS</td><td>2</td></tr><tr><td>306</td><td>Modem test 1850Hz</td><td>2</td></tr><tr><td>307</td><td>Modem test 1650Hz</td><td>2</td></tr><tr><td>308</td><td>Modem test 1100Hz</td><td>2</td></tr><tr><td>309</td><td>Modem test 462Hz</td><td>2</td></tr><tr><td>310</td><td>Modem test 1300Hz</td><td>2</td></tr><tr><td>311</td><td>Modem test 33.6KBPS (V.34)</td><td>2</td></tr><tr><td>312</td><td>Modem test 28.8KBPS (V.34)</td><td>2</td></tr><tr><td>313</td><td>Modem test 24.0KBPS (V.34)</td><td>2</td></tr><tr><td>314</td><td>Modem test 16.8KBPS (V.34)</td><td>2</td></tr><tr><td>315</td><td>Dial test 10PPS</td><td>5</td></tr><tr><td>316</td><td>Dial test 20PPS</td><td>5</td></tr><tr><td>317</td><td>Dial test PB</td><td>5</td></tr><tr><td>318</td><td>Modem test 12.0KBPS (V.17)</td><td>2</td></tr><tr><td>319</td><td>Modem test 7.2KBPS (V.29)</td><td>2</td></tr><tr><td>320</td><td>Modem test 2.4KBPS (V.27ter)</td><td>2</td></tr><tr><td>322</td><td>CML relay ON</td><td>2</td></tr><tr><td>410</td><td>Power supply cooling fan ON/OFF (low speed)</td><td>3</td></tr><tr><td>411</td><td>Power supply cooling fan ON/OFF (high speed)</td><td>3</td></tr><tr><td>461</td><td>Return the Finisher condition to packaging position</td><td>2</td></tr></table><h3>Test print mode (test mode 04)</h3><p></p><p></p><table style='width: 100%'><tr><td>Code</td><td>Types of test pattern</td><td>Remarks</td><td>Remarks</td><td>Output from</td></tr><tr><td>114</td><td>Secondary scanning direction 17 gradation</td><td>Error diffusion</td><td>1</td><td>SLG</td></tr><tr><td>142</td><td>Grid pattern</td><td>Pattern width: 2 dots,</td><td>1</td><td>LGC</td></tr></table> <table style='width: 100%'><tr><td>05/08</td><td>Mode</td><td>Element</td><td>Sub<br /> element</td><td>Item</td><td>Subitem</td><td>Code</td><td>Sub-<br /> code</td><td>Details</td><td>Default<br /> value</td><td>Acceptable<br /> value</td><td>RAM</td><td>Contents</td><td>Proc<br /> edure</td><td>Service<br /> UI</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Developer</td><td>Automatic adjustment of auto-toner sensor</td><td></td><td>2000</td><td></td><td>Fuser heater ON</td><td>-</td><td></td><td>-</td><td>As the value increases, the sensor output increases correspondingly. The value starts changing approx. 2 minutes after this adjustment was started and is automatically set in the range of 2.35 to 2.45 V.<br /> * Selection is disable when developer unit is not installed.</td><td>17</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Developer</td><td>Correction of auto- toner sensor</td><td></td><td>2001</td><td></td><td>Fuser heater ON</td><td>141</td><td>0~255</td><td>M</td><td>Corrects the control value of the auto-toner sensor setup in 05-2000.<br /> * Selection is disable when developer unit is not installed.</td><td>3</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Developer</td><td></td><td></td><td>2020</td><td></td><td>Developer bias DC output adjustment</td><td>141</td><td>0~255</td><td>M</td><td>As the value increases, the transformer output increases correspondingly. Remove the developer unit and install the adjustment jig to make adjustment.</td><td>3</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Charger</td><td></td><td></td><td>2040</td><td></td><td>Main charger grid bias output adjustment</td><td>Refer to contents</td><td>0~255</td><td>M</td><td>As the value increases, the transformer output increases correspondingly. Remove the developer unit and install the adjustment jig to make adjustment.<br /> <Default value><br /> e-STUDIO206L/256/306: 90<br /> e-STUDIO356/456/506: 95</td><td>3</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Transfer</td><td></td><td></td><td>2052</td><td></td><td>Transfer transformer DC output adjustment (C)</td><td>Refer to contents</td><td>0~255</td><td>M</td><td>As the value increases, the transformer output increases correspondingly. Remove the developer unit and install the adjustment jig to make adjustment.<br /> <Default value><br /> e-STUDIO206L/256/306: 88<br /> e-STUDIO356/456/506: 117</td><td>3</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Separation</td><td></td><td></td><td>2078</td><td></td><td>Separation transformer DC output adjustment (C)</td><td>52</td><td>0~255</td><td>M</td><td>As the value increases, the transformer output increases correspondingly. Remove the developer unit and install the adjustment jig to make adjustment.</td><td>3</td><td></td></tr></table> <table style='width: 100%'><tr><td>05/08</td><td>Mode</td><td>Element</td><td>Sub<br /> element</td><td>Item</td><td>Subitem</td><td>Code</td><td>Sub-<br /> code</td><td>Details</td><td>Default<br /> value</td><td>Acceptable<br /> value</td><td>RAM</td><td>Contents</td><td>Proc<br /> edure</td><td>Service<br /> UI</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Transfer</td><td>Transfer cleaning bias adjustment</td><td></td><td>2083</td><td></td><td>Positive</td><td>Refer to contents</td><td>0~255</td><td>M</td><td>When the high-voltage transformer is replaced, the transfer cleaning bias needs to be adjusted with this code. The larger the setting value is, the higher the value of the current (more positive) is. This causes a reduction in the toner adhering to the transfer roller and an improvement in the cleaning performance. Perform this adjustment after the process units (cleaner and developer unit) have been removed. When the high- voltage transformer is replaced, adjusting with the following codes needs to be performed in addition to this adjustment.<br /> 05-2020, 05-2040, 05-2052, 05-2078<br /> <Default value><br /> e-STUDIO206L/256/306: 63<br /> e-STUDIO356/456/506: 96</td><td>3</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Transfer</td><td>Transfer cleaning bias adjustment</td><td></td><td>2084</td><td></td><td>Negative</td><td>41</td><td>0~255</td><td>M</td><td>When the high-voltage transformer is replaced, the transfer cleaning bias needs to be adjusted with this code. The larger the setting value is, the higher the value of the current (more negative) is. This causes a reduction in the toner adhering to the transfer roller and an improvement in the cleaning performance. Perform this adjustment after the process units (cleaner and developer unit) have been removed. When the high- voltage transformer is replaced, adjusting with the following codes need to be performed in addition to this adjustment.<br /> 05-2020, 05-2040, 05-2052, 05-2078</td><td>3</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Transfer</td><td>Temperature/humidity sensor</td><td></td><td>2192</td><td></td><td>Humidity display</td><td>50</td><td>0~100</td><td>M</td><td>Displays the humidity value detected by temperature/humidity sensor.</td><td>2</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Process</td><td>Temperature/humidity sensor</td><td></td><td>2194</td><td></td><td>Temperature display</td><td>25</td><td>0~50</td><td>M</td><td>Displays the humidity value detected by temperature/humidity sensor.</td><td>2</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Charger</td><td></td><td></td><td>2196</td><td></td><td>Drum thermistor<br /> temperature display (K)</td><td>25</td><td>0~100</td><td>M</td><td>(Unit: °C)</td><td>2</td><td>Yes</td></tr></table> <table style='width: 100%'><tr><td>05/08</td><td>Mode</td><td>Element</td><td>Sub<br /> element</td><td>Item</td><td>Subitem</td><td>Code</td><td>Sub-<br /> code</td><td>Details</td><td>Default<br /> value</td><td>Acceptable<br /> value</td><td>RAM</td><td>Contents</td><td>Proc<br /> edure</td><td>Service<br /> UI</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Image quality control</td><td></td><td></td><td>2250</td><td></td><td>Laser power adjustment</td><td>Refer to contents</td><td>0~255</td><td>M</td><td>When the value increases, the laser output increases correspondingly.<br /> <Default value><br /> e-STUDIO206L/256/306: 65<br /> e-STUDIO356/456/506: 121</td><td>3</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Process</td><td></td><td></td><td>2382</td><td></td><td>Reverse time of the drum</td><td>Refer to contents</td><td>0~255</td><td>M</td><td><Default value><br /> e-STUDIO206L/256/306: 12<br /> e-STUDIO356/456/506: 8</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Process</td><td>Toner recycle</td><td></td><td></td><td>2390</td><td></td><td>Forced performing of idling</td><td>-</td><td></td><td>M</td><td>Perform this adjustment before the replacement of the developer material. (The toner is forcibly removed from the cleaner.)</td><td>6</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td></td><td></td><td>3009</td><td></td><td>Log table switching for RADF copying (color)</td><td>0</td><td>0~4</td><td>SYS</td><td>0: Same log table as the one used at copying with original glass<br /> 1: Background reproduction - Light 2<br /> 2: Background reproduction - Light 1<br /> 3: Background reproduction - Dark 1<br /> 4: Background reproduction - Dark 2</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td>Image location adjustment</td><td></td><td>3030</td><td></td><td>Primary scanning<br /> direction (scan. section)</td><td>75</td><td>0~255</td><td>SYS</td><td>When the value increases by "1", the image shifts by approx. 0.04233 mm toward the front side of the paper.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td>Image location adjustment</td><td></td><td>3031</td><td></td><td>Secondary scanning direction(scan.section<br /> )</td><td>130</td><td>90~166</td><td>SYS</td><td>When the value increases by "1", the image shifts by<br /> approx. 0.13013 mm toward the trailing edge of the paper.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td>Reproduction ratio adjustment</td><td></td><td>3032</td><td></td><td>Adj. secondary scan.direction</td><td>128</td><td>63~193</td><td>SYS</td><td>When the value increases by "1", the reproduction ratio in the secondary scanning direction (vertical to paper feeding direction) increases by approx. 0.025 %.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td>Distortion mode</td><td></td><td>3033</td><td></td><td>Distortion mode</td><td>-</td><td></td><td>-</td><td>Moves carriages to the adjusting position.</td><td>6</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td>Shading position adjustment</td><td></td><td>3034</td><td></td><td>Original glass</td><td>117</td><td>92~165</td><td>SYS</td><td>0.13013 mm/step</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td>Shading position adjustment</td><td></td><td>3035</td><td></td><td>RADF</td><td>133</td><td>92~165</td><td>SYS</td><td>0.13013 mm/step</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>RADF</td><td>Adjustment of RADF paper alignment</td><td></td><td>3040</td><td></td><td>Front side</td><td>10</td><td>0~20</td><td>SYS</td><td>When the value increases by "1", the aligning amount increases by approx. 0.5 mm.</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>RADF</td><td>Adjustment of RADF paper alignment</td><td></td><td>3041</td><td></td><td>Back side</td><td>10</td><td>0~20</td><td>SYS</td><td>When the value increases by "1", the aligning amount increases by approx. 0.5 mm.</td><td>1</td><td></td></tr></table> <table style='width: 100%'><tr><td>05/08</td><td>Mode</td><td>Element</td><td>Sub<br /> element</td><td>Item</td><td>Subitem</td><td>Code</td><td>Sub-<br /> code</td><td>Details</td><td>Default<br /> value</td><td>Acceptable<br /> value</td><td>RAM</td><td>Contents</td><td>Proc<br /> edure</td><td>Service<br /> UI</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>RADF</td><td></td><td></td><td>3042</td><td></td><td>Fine adjustment of RADF transport speed</td><td>50</td><td>0~100</td><td>SYS</td><td>When the value increases by "1", the reproduction ratio of the secondary scanning direction when using the RADF increases by approx. 0.1%.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>RADF</td><td></td><td></td><td>3043</td><td></td><td>RADF sideways deviation adjustment</td><td>128</td><td>0~255</td><td>SYS</td><td>When the value increases by "1", the image of original fed from the RADF shifts toward the rear side of paper by approx. 0.08423 mm.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>RADF</td><td>RADF leading edge position adjustment</td><td></td><td>3044</td><td></td><td>Front side</td><td>50</td><td>0~100</td><td>SYS</td><td>When the value increases by "1", the copied image of original fed from the RADF shifts toward the trailing edge of paper by approx.0.2 mm.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>RADF</td><td>Leading edge position adjustment</td><td></td><td>3045</td><td></td><td>Back side</td><td>50</td><td>0~100</td><td>SYS</td><td>When the value increases by "1", the copied image of original fed from the RADF shifts toward the trailing edge of paper by approx.0.2 mm.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td></td><td></td><td>3046</td><td></td><td>Carriage position adjustment during scanning from RADF (black)</td><td>128</td><td>0~255</td><td>SYS</td><td>When the value increases by "1", the carriage position shifts by approx. 0.1 mm toward the exit side when using the RADF.</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td></td><td></td><td>3047</td><td></td><td>Carriage position adjustment during scanning from RADF (color)</td><td>128</td><td>0~255</td><td>SYS</td><td>When the value increases by "1", the carriage position shifts by approx. 0.1 mm toward the exit side when using the RADF.</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td>Data transfer of characteristic value</td><td></td><td>3203</td><td></td><td>SLG board -> SYS board</td><td>-</td><td></td><td>SYS</td><td>Transfers the characteristic values of the scanner (shading correction factor / RGB color correction / reproduction ratio color deviation correction / shading position correction factor / reproduction ratio correction value in primary scanning direction)</td><td>6</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Scanner</td><td>Scanner</td><td></td><td></td><td>3209</td><td></td><td>Data transfer of characteristic value of scanner / SYS board -<br /> > SLG board</td><td>-</td><td></td><td>SYS</td><td>Transfers the characteristic values of the scanner (shading correction factor / RGB color correction / reproduction ratio color aberration correction / shading position correction factor / reproduction ratio correction value in primary scanning direction)</td><td>6</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Printer</td><td>Fine adjustment of polygonal motor rotation speed</td><td>Adjustment of primary scanning direction reproduction ratio</td><td>4000</td><td></td><td>PPC</td><td>130</td><td>0~255</td><td>M</td><td>When the value increases by "1", the reproduction ratio of primary scanning direction increases by approx.<br /> 0.07%. (approx. 0.1 mm/step)</td><td>1</td><td>Yes</td></tr></table> <table style='width: 100%'><tr><td>05/08</td><td>Mode</td><td>Element</td><td>Sub<br /> element</td><td>Item</td><td>Subitem</td><td>Code</td><td>Sub-<br /> code</td><td>Details</td><td>Default<br /> value</td><td>Acceptable<br /> value</td><td>RAM</td><td>Contents</td><td>Proc<br /> edure</td><td>Service<br /> UI</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Printer</td><td>Fine adjustment of polygonal motor rotation speed</td><td>Adjustment of primary scanning direction reproduction ratio</td><td>4001</td><td></td><td>PRT</td><td>133</td><td>0~255</td><td>M</td><td>When the value increases by "1", the reproduction ratio of primary scanning direction increases by approx.<br /> 0.07%. (approx. 0.1 mm/step)</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Adjustment of primary scanning laser writing start position.</td><td></td><td>4005</td><td></td><td>PPC</td><td>Refer to contents</td><td>0~255</td><td>M</td><td>When the value increases by "1", the writing start position shifts to the front side by approx. 0.0423 mm.<br /> <Default value><br /> e-STUDIO206L/256/306: 88<br /> e-STUDIO356/456/506: 99</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Adjustment of primary scanning laser writing start position.</td><td></td><td>4006</td><td></td><td>PRT</td><td>Refer to contents</td><td>0~255</td><td>M</td><td>When the value increases by "1", the writing start position shifts to the front side by approx. 0.0423 mm.<br /> <Default value><br /> e-STUDIO206L/256/306: 88<br /> e-STUDIO356/456/506: 99</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Drive</td><td>Fine adjustment of main motor speed</td><td>Adjustment of secondary scanning direction reproduction ratio</td><td>4009</td><td></td><td>PPC/PRT</td><td>132</td><td>0~255</td><td>M</td><td>When the value increases by "1", the reproduction ratio of secondary scanning direction increases by approx. 0.04%.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Drive</td><td>Fine adjustment of main motor speed</td><td>Adjustment of secondary scanning direction reproduction ratio</td><td>4010</td><td></td><td>FAX</td><td>128</td><td>0~255</td><td>M</td><td>When the value increases by "1", the reproduction ratio of secondary scanning direction increases by approx. 0.04%.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Drive</td><td>Fine adjustment of exit motor speed</td><td></td><td>4013</td><td></td><td>PPC/PRT</td><td>128</td><td>0~255</td><td>M</td><td>e-STUDIO206L/256/306: When the value increases by "1", the rotation accelerates by approx. 0.03%.<br /> e-STUDIO356/456/506: When the value increases by "1", the rotation accelerates by approx. 0.05%.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Drive</td><td>Fine adjustment of exit motor speed</td><td></td><td>4014</td><td></td><td>FAX</td><td>128</td><td>0~255</td><td>M</td><td>e-STUDIO206L/256/306:When the value increases by "1", the rotation accelerates by approx. 0.03%.<br /> e-STUDIO356/456/506:When the value increases by "1", the rotation accelerates by approx. 0.05%.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Adj. of drawer sideways deviation</td><td></td><td>4018</td><td>0</td><td>1st drawer</td><td>128</td><td>0~255</td><td>M</td><td>When the value increases by "1", the image shifts toward the front side by 0.0423 mm.</td><td>4</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Adj. of drawer sideways deviation</td><td></td><td>4018</td><td>1</td><td>2nd drawer</td><td>128</td><td>0~255</td><td>M</td><td>When the value increases by "1", the image shifts toward the front side by 0.0423 mm.</td><td>4</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Adj. of drawer sideways deviation</td><td></td><td>4018</td><td>2</td><td>PFP upper drawer</td><td>128</td><td>0~255</td><td>M</td><td>When the value increases by "1", the image shifts toward the front side by 0.0423 mm.</td><td>4</td><td>Yes</td></tr></table> <table style='width: 100%'><tr><td>05/08</td><td>Mode</td><td>Element</td><td>Sub<br /> element</td><td>Item</td><td>Subitem</td><td>Code</td><td>Sub-<br /> code</td><td>Details</td><td>Default<br /> value</td><td>Acceptable<br /> value</td><td>RAM</td><td>Contents</td><td>Proc<br /> edure</td><td>Service<br /> UI</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Adj. of drawer sideways deviation</td><td></td><td>4018</td><td>3</td><td>PFP lower drawer</td><td>128</td><td>0~255</td><td>M</td><td>When the value increases by "1", the image shifts toward the front side by 0.0423 mm.</td><td>4</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Adj. of drawer sideways deviation</td><td></td><td>4018</td><td>4</td><td>T-LCF</td><td>128</td><td>0~255</td><td>M</td><td>When the value increases by "1", the image shifts toward the front side by 0.0423 mm.</td><td>4</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Adj. of drawer sideways deviation</td><td></td><td>4018</td><td>5</td><td>Bypass feeding</td><td>128</td><td>0~255</td><td>M</td><td>When the value increases by "1", the image shifts toward the front side by 0.0423 mm.</td><td>4</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Adj. of primary scan. laser writing start</td><td>Duplex feeding</td><td>4019</td><td>0</td><td>Long size</td><td>148</td><td>0~255</td><td>M</td><td>When the value increases by "1", the image shifts toward the front side by 0.0423 mm.</td><td>4</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Adj. of primary scan. laser writing start</td><td>Duplex feeding</td><td>4019</td><td>1</td><td>Short size</td><td>148</td><td>0~255</td><td>M</td><td>When the value increases by "1", the image shifts toward the front side by 0.0423 mm.</td><td>4</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Margin adjustment</td><td>PPC</td><td>4050</td><td></td><td>Top margin adjustment</td><td>15</td><td>0~255</td><td>M</td><td>When the value increases by "1", the blank area becomes wider by approx. 0.0423 mm.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td></td><td></td><td>4051</td><td></td><td>Left margin adjustment(blank area at the left of the paper along the paper feeding direction)</td><td>0</td><td>0~255</td><td>M</td><td>When the value increases by "1", the blank area becomes wider by approx. 0.0423 mm.</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Margin adjustment</td><td>PPC</td><td>4052</td><td></td><td>Right margin adjustment</td><td>Refer to contents</td><td>0~255</td><td>M</td><td>When the value increases by "1", the blank area becomes wider by approx. 0.0423 mm.<br /> <Default value><br /> e-STUDIO206L/256/306: 6<br /> e-STUDIO356/456/506: 24</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Margin adjustment</td><td>PPC</td><td>4053</td><td></td><td>Bottom margin adjustment</td><td>55</td><td>0~255</td><td>M</td><td>When the value increases by "1", the blank area becomes wider by approx. 0.0423 mm.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td></td><td></td><td>4054</td><td></td><td>Top margin adjustment(blank area at the leading edge of the paper)</td><td>24</td><td>0~255</td><td>M</td><td>When the value increases by "1", the blank area becomes wider by approx. 0.0423 mm.</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td></td><td></td><td>4055</td><td></td><td>Left margin adjustment(blank area at the left of the paper along the paper feeding direction)</td><td>0</td><td>0~255</td><td>M</td><td>When the value increases by "1", the blank area becomes wider by approx. 0.0423 mm.</td><td>1</td><td></td></tr></table> <table style='width: 100%'><tr><td>05/08</td><td>Mode</td><td>Element</td><td>Sub<br /> element</td><td>Item</td><td>Subitem</td><td>Code</td><td>Sub-<br /> code</td><td>Details</td><td>Default<br /> value</td><td>Acceptable<br /> value</td><td>RAM</td><td>Contents</td><td>Proc<br /> edure</td><td>Service<br /> UI</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td></td><td></td><td>4056</td><td></td><td>Right margin adjustment(blank area at the right of the paper along the paper feeding direction)</td><td>0</td><td>0~255</td><td>M</td><td>When the value increases by "1", the blank area becomes wider by approx. 0.0423 mm.</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td></td><td></td><td>4057</td><td></td><td>Bottom margin adjustment(blank area at the trailing edge of the paper)</td><td>0</td><td>0~255</td><td>M</td><td>When the value increases by "1", the blank area becomes wider by approx. 0.0423 mm.</td><td>1</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Leading edge position adjustment</td><td>Normal speed</td><td>4058</td><td></td><td>1st drawer</td><td>6</td><td>0~15</td><td>M</td><td>When the value increases by "1", the image shifts<br /> toward the trailing edge of the paper by approx. 0.4 mm.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Leading edge position adjustment</td><td>Normal speed</td><td>4059</td><td></td><td>2nd drawer</td><td>Refer to contents</td><td>0~40</td><td>M</td><td>When the value increases by "1", the image shifts toward the trailing edge of the paper by approx. 0.4 mm.<br /> <Default value><br /> e-STUDIO206L/256/306: 20<br /> e-STUDIO356/456/506: 27</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Leading edge position adjustment</td><td>Normal speed</td><td>4060</td><td></td><td>PFP</td><td>8</td><td>0~15</td><td>M</td><td>When the value increases by "1", the image shifts<br /> toward the trailing edge of the paper by approx. 0.4 mm.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Leading edge position adjustment</td><td>Normal speed</td><td>4061</td><td></td><td>Bypass feeding</td><td>Refer to contents</td><td>0~15</td><td>M</td><td>When the value increases by "1", the image shifts toward the trailing edge of the paper by approx. 0.4 mm.<br /> <Default value><br /> e-STUDIO206L/256/306: 7<br /> e-STUDIO356/456/506: 8</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Leading edge position adjustment</td><td>Normal speed</td><td>4062</td><td></td><td>Duplex feeding</td><td>8</td><td>0~15</td><td>M</td><td>When the value increases by "1", the image shifts toward the trailing edge of the paper by approx. 0.4<br /> mm.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td>Leading edge position adjustment</td><td>Normal speed</td><td>4063</td><td></td><td>O-LCF</td><td>8</td><td>0~15</td><td>M</td><td>When the value increases by "1", the image shifts toward the trailing edge of the paper by approx. 0.4<br /> mm.</td><td>1</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td></td><td></td><td>4064</td><td>0</td><td>Bottom margin adjustment (blank area at the trailing edge of the paper)/Reverse side at duplexing</td><td>29</td><td>0~255</td><td>M</td><td>When the value increases by "1", the blank area becomes wider by approx. 0.0423 mm.</td><td>4</td><td></td></tr></table> <table style='width: 100%'><tr><td>05/08</td><td>Mode</td><td>Element</td><td>Sub<br /> element</td><td>Item</td><td>Subitem</td><td>Code</td><td>Sub-<br /> code</td><td>Details</td><td>Default<br /> value</td><td>Acceptable<br /> value</td><td>RAM</td><td>Contents</td><td>Proc<br /> edure</td><td>Service<br /> UI</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Image</td><td></td><td></td><td>4064</td><td>1</td><td>Right margin adjustment (blank area at the right of the paper along the paper feeding direction)/Reverse side at duplexing</td><td>0</td><td>0~255</td><td>M</td><td>When the value increases by "1", the blank area becomes wider by approx. 0.0423 mm.</td><td>4</td><td></td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Feeding system/Pa per transport</td><td>Paper aligning amount adjustment</td><td>1st drawer</td><td>4100</td><td>0</td><td>Plain paper; Long size</td><td>Refer to contents</td><td>0~63</td><td>M</td><td>e-STUDIO206L/256/306:When the value increases by “1”, the aligning amount increases by approx. 0.3 mm. e-STUDIO356/456/506:When the value increases by “1”, the aligning amount increases by approx. 0.4 mm.<br /> <Paper length><br /> Long size: 330 mm or longer Middle size: 220 mm to 329 mm Short size: 219 mm or shorter<br /> <Default value><br /> e-STUDIO206L/256/306: 37<br /> e-STUDIO356/456: 21<br /> e-STUDIO506: 17</td><td>4</td><td>Yes</td></tr><tr><td>05</td><td>Adjustmen t mode</td><td>Printer</td><td>Feeding system/Pa per transport</td><td>Paper aligning amount adjustment</td><td>1st drawer</td><td>4100</td><td>1</td><td>Plain paper; Middle size</td><td>Refer to contents</td><td>0~63</td><td>M</td><td>e-STUDIO206L/256/306:When the value increases by “1”, the aligning amount increases by approx. 0.3 mm. e-STUDIO356/456/506:When the value increases by “1”, the aligning amount increases by approx. 0.4 mm.<br /> <Paper length><br /> Long size: 330 mm or longer Middle size: 220 mm to 329 mm Short size: 219 mm or shorter<br /> <Default value><br /> e-STUDIO206L/256/306: 37<br /> e-STUDIO356/456: 21<br /> e-STUDIO506: 17</td><td>4</td><td>Yes</td></tr></table> <table style='width: 100%'><tr><td>05/08</td><td>Mode</td><td>Element</td><td>Sub<br /> element</td><td>Item</td><td>Subitem</td><td>Code</td><td>Sub-<br /> code</td><td>Details</td><td>Default<br /> value</td><td>Acceptable<br /> value</td><td>RAM</td><td>Contents</td><td>Proc<br /> edure</td><td>Service<br /> UI</td></tr><tr><td>05</td><td>Adjustmen</td><td>Printer</td><td>Feeding</td><td>Paper aligning</td><td>1st drawer</td><td>4100</td><td>2</td><td>Plain paper; Short</td><td>Refer to</td><td>0~63</td><td>M</td><td>e-STUDIO206L/256/306:When the value increases by</td><td>4</td><td>Yes</td></tr><tr><td></td><td>t mode</td><td></td><td>system/Pa</td><td>amount adjustment</td><td></td><td></td><td></td><td>size1</td><td>contents</td><td></td><td></td><td>“1”, the aligning amount increases by approx. 0.3 mm.</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td>per</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO356/456/506:When the value increases by</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td>transport</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>“1”, the aligning amount increases by approx. 0.4 mm.</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td><Paper length></td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Long size: 330 mm or longer</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Middle size: 220 mm to 329 mm</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Short size: 219 mm or shorter</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td><Default value></td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO206L/256/306: 37</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO356/456: 21</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO506: 17</td><td></td><td></td></tr><tr><td>05</td><td>Adjustmen</td><td>Printer</td><td>Feeding</td><td>Paper aligning</td><td>2nd drawer</td><td>4101</td><td>0</td><td>Plain paper; Long</td><td>Refer to</td><td>0~63</td><td>M</td><td>e-STUDIO206L/256/306:When the value increases by</td><td>4</td><td></td></tr><tr><td></td><td>t mode</td><td></td><td>system/Pa</td><td>amount adjustment</td><td></td><td></td><td></td><td>size</td><td>contents</td><td></td><td></td><td>“1”, the aligning amount increases by approx. 0.3 mm.</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td>per</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO356/456/506:When the value increases by</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td>transport</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>“1”, the aligning amount increases by approx. 0.4 mm.</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td><Paper length></td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Long size: 330 mm or longer</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Middle size: 220 mm to 329 mm</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Short size: 219 mm or shorter</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td><Default value></td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO206L/256/306: 30</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO356/456: 15</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO506: 9</td><td></td><td></td></tr></table> <table style='width: 100%'><tr><td>05/08</td><td>Mode</td><td>Element</td><td>Sub<br /> element</td><td>Item</td><td>Subitem</td><td>Code</td><td>Sub-<br /> code</td><td>Details</td><td>Default<br /> value</td><td>Acceptable<br /> value</td><td>RAM</td><td>Contents</td><td>Proc<br /> edure</td><td>Service<br /> UI</td></tr><tr><td>05</td><td>Adjustmen</td><td>Printer</td><td>Feeding</td><td>Paper aligning</td><td>2nd drawer</td><td>4101</td><td>1</td><td>Plain paper; Middle</td><td>Refer to</td><td>0~63</td><td>M</td><td>e-STUDIO206L/256/306:When the value increases by</td><td>4</td><td></td></tr><tr><td></td><td>t mode</td><td></td><td>system/Pa</td><td>amount adjustment</td><td></td><td></td><td></td><td>size</td><td>contents</td><td></td><td></td><td>“1”, the aligning amount increases by approx. 0.3 mm.</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td>per</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO356/456/506:When the value increases by</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td>transport</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>“1”, the aligning amount increases by approx. 0.4 mm.</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td><Paper length></td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Long size: 330 mm or longer</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Middle size: 220 mm to 329 mm</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Short size: 219 mm or shorter</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td><Default value></td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO206L/256/306: 28</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO356/456: 15</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO506: 9</td><td></td><td></td></tr><tr><td>05</td><td>Adjustmen</td><td>Printer</td><td>Feeding</td><td>Paper aligning</td><td>2nd drawer</td><td>4101</td><td>2</td><td>Plain paper; Short</td><td>Refer to</td><td>0~63</td><td>M</td><td>e-STUDIO206L/256/306:When the value increases by</td><td>4</td><td></td></tr><tr><td></td><td>t mode</td><td></td><td>system/Pa</td><td>amount adjustment</td><td></td><td></td><td></td><td>size1</td><td>contents</td><td></td><td></td><td>“1”, the aligning amount increases by approx. 0.3 mm.</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td>per</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO356/456/506:When the value increases by</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td>transport</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>“1”, the aligning amount increases by approx. 0.4 mm.</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td><Paper length></td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Long size: 330 mm or longer</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Middle size: 220 mm to 329 mm</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>Short size: 219 mm or shorter</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td><Default value></td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO206L/256/306: 25</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO356/456: 14</td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>e-STUDIO506: 9</td><td></td><td></td></tr></table></blockquote><p></p>

Name

Verification