HOME PAGE | < Previous | Contents | Next >
Input and Output Check
Input and Output Check
Input and Output Check
3.1 INPUT CHECK TABLE
5803 | [INPUT Check] | ||
001 | Registration Sensor | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on register sensor position. (0: paper exist, 1: paper non exist) | |||
002 | Paper Feed Sensor 1 | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on 1st paper feed sensor position. (0: paper exist, 1: paper non exist) | |||
003 | Transport Sensor 1 | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on 1st carry sensor position. (0: paper exist, 1: paper non exist) | |||
004 | Paper Feed Sensor 2 | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on 2nd paper feed sensor position. (0: paper exist, 1: paper non exist) | |||
005 | Transport Sensor 2 | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on 2nd carry sensor position. (0: paper exist, 1: paper non exist) | |||
Input Check Table
006 | Fusing Entrance Sensor | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on fusing entrance sensor position. (0: paper exist, 1: paper non exist) | |||
007 | Fusing Exit Sensor | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on fusing exit sensor position. (0: paper exist, 1: paper non exist) | |||
008 | Paper Exit Sensor | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on paper exit sensor position. (0: paper exist, 1: paper non exist) | |||
009 | Inverter Sensor | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on reverse sensor position. (0: paper exist, 1: paper non exist) | |||
010 | Duplex Exit Sensor | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on duplex exit sensor position. (0: paper exist, 1: paper non exist) | |||
011 | Duplex Entrance Sensor | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on duplex entrance sensor position. (0: paper exist, 1: paper non exist) | |||
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
012 | Tray Full Exit Sensor | ENG | [0 or 1 / 0 / 1/step] 0: Not full 1: full |
Detects paper full of main unit paper exit tray. (0: Not full, 1: full) | |||
013 | Tray 1: Paper Height Sensor | ENG | [0 to 3 / 0 / 1/step] When full is 100%, 11: 71 to 100% 01: 31 to 70% 00: 11 to 30% 10: 1 to 10% |
Detects remaining paper amount of 1st paper feed tray. (When full is 100%, 11: 71 to 100%, 01: 31 to 70%, 00: 11 to 30%, 10: 1 to 10%) *Check SP5-803-015 for paper end. | |||
014 | Tray 1: Upper Limit Sensor | ENG | [0 or 1 / 0 / 1/step] 0: less then limit 1: high then limit |
Detects the hight of paper loaded in 1st paper feed tray. (0: less then limit, 1: high then limit) | |||
015 | Tray 1: Paper End Detection | ENG | [0 or 1 / 0 / 1/step] 0: No paper 1: paper remaining |
Detects paper is running out on 1st paper feed tray. (0: No paper, 1: paper remaining) | |||
016 | Tray 1: Set Sensor | ENG | [0 or 1 / 0 / 1/step] 0: set 1:not set |
Detects that 1st paper feed tray is set to main unit. (0: set, 1:not set) | |||
Input Check Table
017 | Tray 2: Paper Height Sensor | ENG | [0 to 3 / 0 / 1/step] When full is 100%, 11: 71 to 100% 01: 31 to 70% 00: 11 to 30% 10: 1 to 10% |
Detects remaining paper amount of 2nd paper feed tray. (When full is 100%, 11: 71 to 100%, 01: 31 to 70%, 00: 11 to 30%, 10: 1 to 10%) *Check SP5-803-019 for paper end. | |||
018 | Tray 2: Paper End Sensor | ENG | [0 or 1 / 0 / 1/step] 0: less then limit 1: high then limit |
Detects the hight of paper loaded in 2nd paper feed tray. (0: less then limit, 1: high then limit) | |||
019 | Tray 2: Paper End Detection | ENG | [0 or 1 / 0 / 1/step] 0: No paper 1: paper remaining |
Detects paper running out of 2nd paper feed tray. (0: No paper, 1: paper remaining) | |||
020 | Tray 2: Set Sensor | ENG | [0 or 1 / 0 / 1/step] 0: set 1: not set |
Detects that 2nd paper feed tray is set to main unit. (0: set, 1:not set) | |||
021 | Tray 2: Size Sensor | ENG | [0 to 15 / 0 / 1/step] |
Value changes depending on paper size (fence position) set to 2nd paper feed tray. | |||
022 | By-pass: Paper End Sensor | ENG | [0 or 1 / 0 / 1/step] 0: No paper 1: paper remaining |
Detects paper is running out on bypass tray. (0: No paper, 1: paper remaining) | |||
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
023 | By-pass: Main Scan Length Sensor | ENG | [0 to 31 / 0 / 1/step] |
Value changes depending on main scan direction of paper set to bypass tray. | |||
024 | By-pass: Sub Scan Length Sensor | ENG | [0 or 1 / 0 / 1/step] |
Value changes depending on sub scan direction of paper set to bypass tray. | |||
025 | Interlock Release Detection | ENG | [0 to 1 / 0 / 1/step] 00: Unlocked 11: Locked |
Detects open/close of interlock switch (front cover/right cover). (00: Unlocked, 11: Locked) | |||
026 | Right Door Open/Close Sensor | ENG | [0 or 1 / 0 / 1/step] 0: close 1: open |
Detects right door status. (0: close, 1: open) | |||
027 | Duplex Guide Plate Open/Close Sensor | ENG | [0 or 1 / 0 / 1/step] 0: close 1: open |
Detects duplex guide plate status. (0: close, 1: open) | |||
028 | PTR Open/Close Sensor | ENG | [0 or 1 / 0 / 1/step] 0: open 1: close |
Detects paper transfer unit status. (0: open, 1: close) | |||
029 | ITB Contact Sensor | ENG | [0 or 1 / 0 / 1/step] 0: Abutting 1: Alienate |
Detects image transfer roller (Y, M, C) and photoreceptors distance. (0: Abutting, 1: Alienate) | |||
Input Check Table
030 | PTR Contact Sensor | ENG | [0 or 1 / 0 / 1/step] 0: Abutting 1: Alienate |
Detects image transfer belt and paper transfer rollers distance. (0: Abutting, 1: Alienate) | |||
031 | New ITB Unit Detection | ENG | [0 or 1 / 0 / 1/step] |
Not available with C1 | |||
032 | Toner Collection Full Sensor | ENG | [0 or 1 / 0 / 1/step] 0: Not full 1: full |
Detects full of waste toner bottle. (0: Not full, 1: full) | |||
033 | Toner Collection Bottle Set Sensor | ENG | [0 or 1 / 0 / 1/step] 0: set 1: not set |
Detects that waste toner bottle is set to main unit. (0: set, 1:not set) | |||
034 | Toner End Sensor:Y | ENG | [0 or 1 / 0 / 1/step] 0: End 1: Not End |
Detects remaining toner amount. *Power with SP5-804-173 before checking. (0: End, 1: Not End) | |||
035 | Toner End Sensor:M | ENG | [0 or 1 / 0 / 1/step] 0: End 1: Not End |
Detects remaining toner amount. *Power with SP5-804-173 before checking. (0: End, 1: Not End) | |||
036 | Toner End Sensor:C | ENG | [0 or 1 / 0 / 1/step] 0: End 1: Not End |
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
Detects remaining toner amount. *Power with SP5-804-173 before checking. (0: End, 1: Not End) | |||
037 | Toner End Sensor:K | ENG | [0 or 1 / 0 / 1/step] 0: End 1: Not End |
Detects remaining toner amount. *Power with SP5-804-172 before checking. (0: End, 1: Not End) | |||
038 | Fusing:Area Detection | ENG | [0 to 15 / 0 / 1/step] 0111:200V system 1011:100V System |
Detects region of fusing unit. (0111: 200V system, 1011: 100V System) | |||
039 | Fusing:New Unit Detection | ENG | [0 or 1 / 0 / 1/step] 0: New 1: Old |
Detects New/Old of fusing unit. (0: New, 1: Old) | |||
040 | Fusing Temp Detect | ENG | [0 or 1 / 0 / 1/step] 0: Normal 1: High temperature |
Detects whether high temperature is detected from fusing unit. (0: Normal, 1: High temperature) | |||
041 | Fusing Temp Detect 2 | ENG | [0 or 1 / 0 / 1/step] 0: Normal 1: High temperature |
Detects whether high temperature is detected from fusing unit. (0: Normal, 1: High temperature) | |||
Input Check Table
042 | NC Sensor Temp Detection: 1 | ENG | [0 or 1 / 0 / 1/step] 0: Normal 1: High temperature |
Detects whether high temperature is detected from fusing unit. (0: Normal, 1: High temperature) | |||
045 | Drum Phase Sensor: K | ENG | [0 or 1 / 0 / 1/step] |
Not available with C1 | |||
046 | Drum Phase Sensor: FC | ENG | [0 or 1 / 0 / 1/step] |
Not available with C1 | |||
047 | Nip Pres. Release Home Position Sensor | ENG | [0 or 1 / 0 / 1/step] 0: Not pressured 1: pressured |
Detects state of fusing nip pressure. (0: Not pressured, 1: pressured) | |||
048 | Fusing Fan: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of fusing exhaust heat fan. (0: Running, 1: Stopped, or locked) | |||
049 | Dev Fan: Right: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of developer air intake fan (right). (0: Running, 1: Stopped, or locked) | |||
050 | Dev Fan: Left: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of developer air intake fan (left). (0: Running, 1: Stopped, or locked) | |||
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
051 | PSU Cooling Fan: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of PSU cooling fan. (0: Running, 1: Stopped, or locked) | |||
052 | Ozone Fan: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of ozone exhaust air fan. (0: Running, 1: Stopped, or locked) | |||
054 | PSU Fan: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of PSU exhaust heat fan. (0: Running, 1: Stopped, or locked) | |||
055 | PCB Box Cooling Fan: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of electric box cooling fan. (0: Running, 1: Stopped, or locked) | |||
056 | Drive Cooling Fan: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of drive cooling fan. (0: Running, 1: Stopped, or locked) | |||
057 | Ventilation Fan: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of main unit exhaust heat fan. (0: Running, 1: Stopped, or locked) | |||
Input Check Table
058 | Paper Exit Cooling Fan: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of paper exit cooling fan. (0: Running, 1: Stopped, or locked) | |||
060 | Toner Supply Cooling Fan: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of toner supply cooling fan. (0: Running, 1: Stopped, or locked) | |||
061 | Development Motor K: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of developer motor (K). (0: Running, 1: Stopped, or locked) | |||
063 | Development Motor FC: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of developer motor (FC). (0: Running, 1: Stopped, or locked) | |||
064 | Drum Motor FC: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of drum motor (FC). (0: Running, 1: Stopped, or locked) | |||
065 | Fusing Motor: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of fusing motor. (0: Running, 1: Stopped, or locked) | |||
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
066 | Transfer Drum Motor K: Lock | ENG | [0 or 1 / 0 / 1/step] 0: Running 1: Stopped, or locked |
Detects locking of transfer drum motor K. (0: Running, 1: Stopped, or locked) | |||
067 | PP:D:SC Detection | ENG | [0 or 1 / 0 / 1/step] 0: SC detected 1: Normal |
Detects SC of HVP (secession). (0: SC detected, 1: Normal) | |||
068 | PP:CB:SC Detection | ENG | [0 or 1 / 0 / 1/step] 0: SC detected 1: Normal |
Detects SC of HVP (electrify/develop). (0: SC detected, 1: Normal) | |||
069 | PP:TTS:SC Detection | ENG | [0 or 1 / 0 / 1/step] 0: SC detected 1: Normal |
Detects SC of HVP (transfer). (0: SC detected, 1: Normal) | |||
072 | Key Counter: Set 1 | ENG | [0 or 1 / 0 / 1/step] 0: set 1:unset key counter: set 1=0, 2=1 for set, others for unset |
Detects setting of key counter. (0: set, 1:unset) (key counter: set 1=0, 2=1 for set, others for unset) | |||
073 | Key Counter: Set 2 | ENG | [0 or 1 / 0 / 1/step] 0: set 1:unset key counter: set 1=0, 2=1 for set, others for unset |
Input Check Table
Detects setting of key counter. (0: unset, 1:set) (key counter: set 1=0, 2=1 for set, others for unset) | |||
074 | Key Card Set | ENG | [0 or 1 / 0 / 1/step] 0: set 1: not set |
Detects that key card is set to main unit. (0: set, 1:not set) | |||
075 | 1 Bin Tray: Paper Sensor | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Detects that paper is left upon the tray. (0: paper exist, 1: paper non exist) | |||
076 | 1 Bin Tray: Set Detection System | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Detects that tray is set to main unit. (0: set, 1:not set) | |||
077 | Bridge Relay Sensor | ENG | [0 or 1 / 0 / 1/step] 0: paper exist 1: paper non exist |
Responds to paper existence on carry sensor position or bridge unit. (0: paper exist, 1: paper non exist) | |||
078 | Bridge Exit Sensor | ENG | [0 or 1 / 0 / 1/step] 0: Paper exist 1: Paper do not exist |
Responds to paper existence on paper exit sensor position or bridge unit. (0: paper exist, 1: paper non exist) | |||
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
079 | Bridge Set Detection System | ENG | [0 or 1 / 0 / 1/step] 10: set 11:not set |
Detects that bridge unit is set to main unit. (10: set, 11:not set) | |||
080 | 24VS1 Open Detection System | ENG | [0 or 1 / 0 / 1/step] 0: broke 1: continued |
Detects continuity (whether a harness is broken of short circuited) of 24VS1 line on IOB circuit board. (0: broke, 1: continued) | |||
081 | 24VS2 Open Detection System | ENG | [0 or 1 / 0 / 1/step] 0: broke 1: continued |
Detects continuity (whether a harness is broken of short circuited) of 24VS2 line on IOB circuit board. (0: broke, 1: continued) | |||
082 | Bridge Relay/Left Exit Cover Sensor | ENG | [0 or 1 / 0 / 1/step] 0: close 1: open |
Detects open/close of the left carry cover open/close sensor (left paper exit tray) and the relay carry cover open/close sensor (bridge unit). (0: close, 1: open) | |||
083 | Bridge Exit/Upper Exit Cover Sensor | ENG | [0 or 1 / 0 / 1/step] 0: close 1: open |
Detects open/close of the upper carry cover open/close sensor (left paper exit tray) and the relay paper exit cover open/close sensor (bridge unit). (0: close, 1: open) | |||
Input Check Table
084 | Shift Tray: Set Detection System | ENG | [0 or 1 / 0 / 1/step] 01: set 11:not set |
Detects that shift tray is set to main unit. (01: set, 11:not set) | |||
085 | Shift Tray: Position Sensor 1 | ENG | [0 or 1 / 0 / 1/step] 0: Stop on this side. during moving towards inner 1: Stop on inner side. during moving towards this side |
Detects shift tray position. (0: Stop on this side. during moving towards inner, 1: Stop on inner side. during moving towards this side) | |||
086 | Shift Tray: Position Sensor 2 | ENG | [0 or 1 / 0 / 1/step] |
*It its a backup sensor with this machine, so "1" is always displayed) | |||
087 | SI Bypass SF Paper Contact Sensor: Front | ENG | [0.000 to 3.300 / 0.000 / 0.001V] |
Detects side fence position of one action bypass in analog value, and displays sensor output value. | |||
088 | SI Bypass SF Paper Contact Sensor: Rear | ENG | [0.000 to 3.300 / 0.000 / 0.001V] |
Detects side fence position of one action bypass in analog value, and displays sensor output value. | |||
089 | SI Bypass SF Position Sensor | ENG | [88 to 325 / 88 / 1/step] |
Displays output value for side fence position sensor of one action bypass. | |||
090 | PCU Lubricant End Sensor:Y | ENG | [0 or 1 / 0 / 1/step] |
Not available with C1 | |||
091 | PCU Lubricant End Sensor:M | ENG | [0 or 1 / 0 / 1/step] |
Not available with C1 | |||
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
092 | PCU Lubricant End Sensor:C | ENG | [0 or 1 / 0 / 1/step] |
Not available with C1 | |||
093 | PCU Lubricant End Sensor:K | ENG | [0 or 1 / 0 / 1/step] 0: Not end 1: End |
Detects whether lubricant of PCU(K) is end or not. (0: Not end, 1: End) *Only available with c/d/e models. | |||
094 | GAVD Open/Close Detection | ENG | [0 or 1 / 0 / 1/step] |
For checking door open/close during process. No need to operate. | |||
095 | Bridge 24V Fuse Detection | ENG | [0 or 1 / 0 / 1/step] 0: Not cut 1: Cut |
Detects state of 24V fuse on the bridge unit. (0: Not cut, 1: Cut) | |||
096 | Bridge 5V Fuse Detection | ENG | [0 or 1 / 0 / 1/step] 0: Not cut 1: Cut |
Detects state of 5V fuse on the bridge unit. (0: Not cut, 1: Cut) | |||
097 | Fusing Shading Plate Sensor /1 | ENG | [0 or 1 / 0 / 1/step] 0: Not shading 1: shading |
Detects position of fusing shade plate. (0: Not shading 1: shading) | |||
098 | Fusing Shading Plate Sensor /2 | ENG | [0 or 1 / 0 / 1/step] 0: Not shading 1: shading |
Detects position of fusing shade plate. (0: Not shading 1: shading) | |||
Input Check Table
200 | HP Senser | ENG | [0 or 1 / 0 / 1/step] |
Tests the scanner HP sensor. | |||
201 | Platen Cover Sensor | ENG | [0 or 1 / 0 / 1/step] |
Tests the book open/close sensor. | |||
202 | SI Bypass Side Fence Position Sensor- | ENG | [0.000 to 3.300 / 0.000 / 0.001V/step] |
Displays output for side fence position sensor of one action bypass. | |||
5803 | [INPUT Check] | ||
Gets information of specified sensor. | |||
211 | Bank: Tray3: Feed Sensor | ENG | [0 or 1 / 0 / 1/step] 0: paper not detected 1: paper detected. |
212 | Bank: Tray4: Feed Sensor | ENG | |
213 | Bank: Tray5: Feed Sensor | ENG | |
214 | Bank: Tray3: Transport Sensor | ENG | |
215 | Bank: Tray4: Transport Sensor | ENG | |
216 | Bank: Tray5: Transport Sensor | ENG | |
217 | Bank: Feed Cover Open Detection 1 | ENG | [0 or 1 / 0 / 1/step] 0: cover open 1: cover closed |
218 | Bank: Feed Cover Open Detection 2 | ENG | |
219 | LCT Paper Supply Open/Close | ENG | |
220 | LCT Slide Open/Close | ENG | [0 or 1 / 0 / 1/step] 0: slide open 1: slide closed |
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
6007 | [ADF INPUT Check] | ||
Gets sensor information from ADF. Displays signal level of sensor as it is. | |||
001 | Original Length 1 (B5 Detection Sensor) | ENG | [0 or 1 / 0 / 1/step] |
002 | Original Length 2 (A4 Detection Sensor) | ENG | [0 or 1 / 0 / 1/step] |
003 | Original Length 3 (LG Detection Sensor) | ENG | [0 or 1 / 0 / 1/step] |
004 | Original Width 1 | ENG | [0 or 1 / 0 / 1/step] |
005 | Original Width 2 | ENG | [0 or 1 / 0 / 1/step] |
006 | Original Width 3 | ENG | [0 or 1 / 0 / 1/step] |
007 | Original Width 4 | ENG | [0 or 1 / 0 / 1/step] |
008 | Original Width 5 | ENG | [0 or 1 / 0 / 1/step] |
009 | Original Detection | ENG | [0 or 1 / 0 / 1/step] |
011 | Skew Correction | ENG | [0 or 1 / 0 / 1/step] |
013 | Registration Sensor | ENG | [0 or 1 / 0 / 1/step] |
014 | Exit Sensor | ENG | [0 or 1 / 0 / 1/step] |
015 | Feed Cover Sensor | ENG | [0 or 1 / 0 / 1/step] |
016 | Lift Up Sensor | ENG | [0 or 1 / 0 / 1/step] |
023 | Rear Edge Detection | ENG | [0 or 1 / 0 / 1/step] |
Input Check Table
6011 | [1-Pass ADF INPUT Check] | ||
For Single-Pass simultaneous duplex models only. | |||
001 | Original Length 1 (B5 Sensor) | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
002 | Original Length 2 (A4 Sensor) | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
003 | Original Length 3 (LG Sensor) | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
004 | Original Width 1 | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
005 | Original Width 2 | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
006 | Original Width 3 | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
007 | Original Width 4 | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
008 | Original Width 5 | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
009 | Original Detection | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when original is set. | |||
010 | Separation Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
011 | Skew Correction | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
012 | Scan Entrance Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
013 | Registration Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
014 | Exit Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
015 | Feed Cover Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when cover is open. | |||
016 | Lift Up Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when lift up. | |||
018 | Pick-Up Roller HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when pick up roller is not in home position. | |||
Input Check Table
021 | Bottom Plate HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when bottom plate is not in home position. | |||
022 | Bottom Plate Position Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when pick up roller is not in the correct position. | |||
023 | Original Length 4 (LT/A4 Tail Sensor) | ENG | [0 or 1 / 0 / 1/step] |
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area. | |||
6123 | [INPUT Check: 2K/3K FIN] | ||
001 | Entrance Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
002 | Horizontal Transport Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
003 | Switchback Transport Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
004 | Proof Tray Exit Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
005 | Shift Tray Exit Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
006 | Booklet Stapler Exit Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
007 | Paper Exit Open/Close Guide HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
008 | Punch HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
009 | Punch Move HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
010 | S-to-S Registration Detection HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
011 | Lower Junction Solenoid HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
012 | Jogger HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
013 | Positioning Roller HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
014 | Feed-out HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
015 | Stapler Moving HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
016 | Booklet Stapler HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
017 | Booklet Jogger HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
018 | Booklet Jog Solenoid HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
Input Check Table
019 | Booklet Standard Fence HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
020 | Booklet Stapler HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
022 | Folder Blade Cam HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
023 | Folder Blade HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
024 | Shift Roller HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
025 | Shift Jogger HP Sensor: Front | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. * Not use: currently, VOLGA-B does not have setting jogger in system configuration. | |||
026 | Shift Jogger HP Sensor: Rear | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. * Not use: currently, VOLGA-B does not have setting jogger in system configuration. | |||
027 | Shift Jogger Retraction HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. * Not use: currently, VOLGA-B does not have setting jogger in system configuration. | |||
028 | Drag Roller Vibrating HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
029 | LE Guide HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
030 | TE Stack Plate HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
031 | Staple Tray Paper Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
032 | ITB Paper Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
033 | Booklet Stapler Transport Paper Sn: Upper | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
034 | Booklet Stapler Transport Paper Sn: Lower | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
035 | Paper Height Sensor: Shift | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
036 | Corner Stapler Paper Height Sensor 1 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
037 | Corner Stapler Paper Height Sensor 2 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
038 | Proof Tray Full Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
039 | Booklet Stapler Full Sensor 1 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
040 | Booklet Stapler Full Sensor 2 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
Input Check Table
041 | S-to-S Registration Detection Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
042 | Punch RPS Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
043 | Corner Stapler Leading Edge Detection Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
044 | Corner Stapler Staple End Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
045 | Booklet Stapler Staple End Sensor: Front | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
046 | Booklet Stapler Staple End Sensor: Rear | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
047 | Shift Tray Lower Limit Sensor 1 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
048 | Shift Tray Lower Limit Sensor 2 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
049 | Shift Tray Lower Limit Sensor 3 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
050 | Shift Tray Lower Limit Sensor 4 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
051 | Shift Tray Lower Limit Sensor 5 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
052 | Punch Chad Full Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
053 | Punch Set Detection | ENG | [0 or 1 / 0 / 1/step] 0: connected 1: not connected |
Gets connection status of punch unit. | |||
054 | Shift Jogger Set Detection | ENG | [0 or 1 / 0 / 1/step] 0: connected 1: not connected |
Gets connection status of setting jogger unit. * Not use: currently, VOLGA-B does not have setting jogger in system configuration. | |||
055 | Booklet Stapler Set Detection | ENG | [0 or 1 / 0 / 1/step] 0: not connected 1: connected |
Gets connection status of saddle stitch unit. | |||
056 | Front Door SW | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified switch. Displays signal level of switch as it is. | |||
057 | Dynamic Roller Open/Close Guide Plate Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified switch. Displays signal level of switch as it is. | |||
058 | Tray Upper Limit SW | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified switch. Displays signal level of switch as it is. | |||
Input Check Table
059 | Paper Exit Open/Close Guide Plate Limit SW | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified switch. Displays signal level of switch as it is. | |||
060 | Punch Selection DIPSW 1 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified switch. Displays signal level of switch as it is. | |||
061 | Punch Selection DIPSW 2 | ENG | [0 or 1 / 0 / 1/step] |
Gets information of specified switch. Displays signal level of switch as it is. | |||
6135 | [INPUT Check: FrontFIN] | ||
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
001 | Entrance Sensor | *ENG | [0 or 1 / 0 / 1/step] |
002 | Carry Sensor | *ENG | [0 or 1 / 0 / 1/step] |
003 | Exit Sensor | *ENG | [0 or 1 / 0 / 1/step] |
004 | Staple Tray Paper Sensor | *ENG | [0 or 1 / 0 / 1/step] |
005 | Front Jogger HP Sensor | *ENG | [0 or 1 / 0 / 1/step] |
006 | Rear Jogger HP Sensor | *ENG | [0 or 1 / 0 / 1/step] |
007 | Sft Roller HP Sensor | *ENG | [0 or 1 / 0 / 1/step] |
008 | Hitroll HP Sensor | *ENG | [0 or 1 / 0 / 1/step] |
009 | Ext Guide Plate HP Sensor | *ENG | [0 or 1 / 0 / 1/step] |
010 | Staple Moving HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
011 | Shift Tray Paper Sensor | ENG | [0 or 1 / 0 / 1/step] |
012 | Shift Tray Limit Sensor | ENG | [0 or 1 / 0 / 1/step] |
013 | Staple Rotation Sensor | ENG | [0 or 1 / 0 / 1/step] |
014 | Staple Near End Sensor | ENG | [0 or 1 / 0 / 1/step] |
015 | Self Priming Sensor | ENG | [0 or 1 / 0 / 1/step] |
016 | Stopper HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
017 | Punch HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
018 | Punch Pluse Count Sensor | ENG | [0 or 1 / 0 / 1/step] |
019 | Punch Chad Full Sensor | ENG | [0 or 1 / 0 / 1/step] |
020 | Punch Moving HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
021 | Punch Registration Detection HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
022 | Punch Registration Detection Sensor | ENG | [0 or 1 / 0 / 1/step] |
6135 | [INPUT Check: FrontFIN] | ||
Gets information of specified switch. Displays signal level of switch as it is. | |||
023 | Slide Door SW | ENG | [0 or 1 / 0 / 1/step] |
024 | Shift Tray Upper Limit SW | ENG | [0 or 1 / 0 / 1/step] |
6161 | [FIN (1K FIN) INPUT Check] | ||
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
001 | Entrance Sensor | ENG | [0 or 1 / 0 / 1/step] |
002 | Upper Cover Open/Close Sensor | ENG | [0 or 1 / 0 / 1/step] |
003 | Proof Tray Exit Sensor | ENG | [0 or 1 / 0 / 1/step] |
004 | Proof Tray Full Sensor | ENG | [0 or 1 / 0 / 1/step] |
005 | Shift HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
006 | Exit Guide Plate Open/Close HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
007 | Shift Paper Exit (Lift Tray Exit) Sensor | ENG | [0 or 1 / 0 / 1/step] |
008 | Positioning Roller HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
009 | Lift Tray Paper Sensor | ENG | [0 or 1 / 0 / 1/step] |
010 | Jogger HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
Input Check Table
011 | Feed Out HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
012 | Lift Tray Lower Limit Sensor (Upper) | ENG | [0 or 1 / 0 / 1/step] |
013 | Lift Tray Lower Limit Sensor (Lower) | ENG | [0 or 1 / 0 / 1/step] |
014 | Staple Tray Paper Sensor | ENG | [0 or 1 / 0 / 1/step] |
015 | Stapler Moving HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
016 | Near End Sensor (Common: Corner/Bklt Stplr) | ENG | [0 or 1 / 0 / 1/step] |
017 | Self Priming Sensor (Common:Crnr/Bklt Stplr) | ENG | [0 or 1 / 0 / 1/step] |
018 | Driver HP Sensor (Corner/Booklet Stapler) | ENG | [0 or 1 / 0 / 1/step] |
019 | Driver Timing Sensor(Corner/Booklet Stapler) | ENG | [0 or 1 / 0 / 1/step] |
020 | Clincher HP Sensor (Corner/Booklet Stapler) | ENG | [0 or 1 / 0 / 1/step] |
021 | Clincher Timing Sensor (Corner/Bklt Stapler) | ENG | [0 or 1 / 0 / 1/step] |
022 | Stapler Retraction Sensor | ENG | [0 or 1 / 0 / 1/step] |
023 | Punch HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
024 | Punch RP Sensor | ENG | [0 or 1 / 0 / 1/step] |
025 | Punch Hopper Full Sensor | ENG | [0 or 1 / 0 / 1/step] |
026 | Punch Move HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
027 | S-to-S Registration Detection HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
028 | S-to-S Registration Detection Sensor | ENG | [0 or 1 / 0 / 1/step] |
Input and Output Check
Input and Output Check
Input and Output Check
Input Check Table
6161 | [FIN (1K FIN) INPUT Check] | ||
Gets information of specified switch. Displays signal level of switch as it is. | |||
029 | Punch Selection DIPSW 1 | ENG | [0 or 1 / 0 / 1/step] |
030 | Punch Selection DIPSW 2 | ENG | [0 or 1 / 0 / 1/step] |
6161 | [FIN (1K FIN) INPUT Check] | ||
Gets information of specified sensor. Displays signal level of sensor as it is. | |||
031 | ITB Transport Sensor: Right | ENG | [0 or 1 / 0 / 1/step] |
032 | ITB Transport Sensor: Left | ENG | [0 or 1 / 0 / 1/step] |
033 | Stack Transport Sensor | ENG | [0 or 1 / 0 / 1/step] |
034 | Stack Trans Upper Pressure Release HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
035 | Stack Trans Lower Pressure Release HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
036 | Fold Blade HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
037 | Fold Cam HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
038 | TE Stopper Transport Sensor | ENG | [0 or 1 / 0 / 1/step] |
039 | TE Stopper HP Sensor | ENG | [0 or 1 / 0 / 1/step] |
040 | Booklet Folder Exit Sensor | ENG | [0 or 1 / 0 / 1/step] |
041 | Booklet Folder Tray Full Sensor: Upper | ENG | [0 or 1 / 0 / 1/step] |
042 | Booklet Folder Tray Full Sensor: Lower | ENG | [0 or 1 / 0 / 1/step] |
6161 | [FIN (1K FIN) INPUT Check] | ||
Gets information of specified switch. Displays signal level of switch as it is. | |||
043 | Door Open/Close SW | ENG | [0 or 1 / 0 / 1/step] |
044 | Lift Tray Upper Limit SW | ENG | [0 or 1 / 0 / 1/step] |
Input Check Table
6170 | [Bridge: INPUT Check] | ||
001 | Bridge Exit Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information from sensor (relay paper exit sensor... internal paper exit part) of bridge unit. | |||
002 | Bridge Relay Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets information from sensor (relay carry sensor... relay carry to finisher) of bridge unit. | |||
003 | Bridge Set Detection | ENG | [0 or 1 / 0 / 1/step] |
Gets connection information of bridge unit and main unit. When connected, 1. | |||
004 | Bridge Exit Cover | ENG | [0 or 1 / 0 / 1/step] |
Gets micro SW information of bridge unit. When cover open, 1. Main unit paper exit cover. | |||
005 | Bridge Relay Cover | ENG | [0 or 1 / 0 / 1/step] |
Gets micro SW information of bridge unit. When cover open, 1. Finisher side cover. | |||
6172 | [Shift Tray: INPUT Check] | ||
001 | Shift Tray Set Detection | ENG | [0 or 1 / 0 / 1/step] |
Gets connection information of shift tray and main unit. When connected, 1. | |||
002 | Shift Tray Position Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets shift tray position sensor information. | |||
6174 | [1 Bin: INPUT Check] | ||
001 | 1 Bin Set Detection | ENG | [0 or 1 / 0 / 1/step] |
Gets connection information of 1 bin and main unit. When connected, 1. | |||
002 | 1bin Paper Detection Sensor | ENG | [0 or 1 / 0 / 1/step] |
Gets paper existence sensor information from 1 bin. | |||