5009

[Add Display Language]

Adds language available in user choice. (Only the languages registered in the machine)

Refer to the displayed language list to set in the way showed below. List Number Assigned Bit Switch

No.1 to 8 BIT1 to 8 (SP5009-201) No.9 to 16BIT1 to 8 (SP5009-202) No.17 to 24BIT1 to 8 (SP5009-203) No.25 to 32BIT1 to 8 (SP5009-204)

Example: To add American(No.3 in the list) or Czech (No.15) Turn Bit 3 of “SP5009-201” 0 to 1 for American.

Turn Bit 7 of “SP5009-202” 0 to 1 for Czech.

After setting, turn the main power switch off and on to make the setting valid.

201

Bit SW

*CTL

[1 to 255 / 0 / 1/step]

202

Bit SW

*CTL

[1 to 255 / 0 / 1/step]

203

Bit SW

*CTL

[1 to 255 / 0 / 1/step]

204

Bit SW

*CTL

[1 to 255 / 0 / 1/step]

5024

[mm/inch Display Selection]

Display units (mm or inch) for custom paper sizes.

001

0:mm 1:inch

*CTL

[0 or 1 / 1(USA), 0(Others) / 1/step]

0: mm

1: inch

5045

[Accounting counter]

Selects the counting method.

 The counting method can be changed only once, regardless of whether the counter value is negative or positive.

001

Counter Method

*CTL

[0 to 7 / 1 / step]

0: Developments

1: Prints

2: Coverage

7: Coverage (YMC)

5047

[Paper Display]

Turns on or off the printed paper display on the LCD.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

5051

[TonerRefillDisplay]

Enables or disables the toner refill detection display.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: ON

1: OFF

5055

[Display IP Address]

Display or does not display the IP address on the operation panel.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

5061

[Toner Remaining Icon Display Change]

Display or does not display the remaining toner display icon on the LCD.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

5061

[Toner Remaining Icon Display Change]

Display or does not display the remaining toner display icon on the LCD.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

5061

[Toner Remaining Icon Display Change]

Display or does not display the remaining toner display icon on the LCD.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

5062

[Parts Replacement Alert Display]

Display or does not display the PM part yield on the LCD.

002

#Drum unit:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

003

#Development unit:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

011

Coating Bar:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

025

#Drum unit :C

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

026

#Development unit:C

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

048

#Drum unit :M

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

049

Development unit:M

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

5062

[Parts Replacement Alert Display]

Display or does not display the PM part yield on the LCD.

002

#Drum unit:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

003

#Development unit:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

011

Coating Bar:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

025

#Drum unit :C

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

026

#Development unit:C

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

048

#Drum unit :M

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

049

Development unit:M

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

5062

[Parts Replacement Alert Display]

Display or does not display the PM part yield on the LCD.

002

#Drum unit:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

003

#Development unit:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

011

Coating Bar:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

025

#Drum unit :C

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

026

#Development unit:C

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

048

#Drum unit :M

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

049

Development unit:M

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

071

#Drum unit:Y

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

072

#Development unit:Y

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

093

Image Transfer Unit

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

102

Image Transfer Cleaning Unit

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

109

Paper Transfer Roller Unit

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

115

Fusing unit

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

116

Fusing Roller unit

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

118

Pressure Roller

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

131

Filter Ozone Duct

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

132

Filter Heat Exhaust Duct

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

142

Wast Toner bottle

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

206

ADF Pick-up Roller

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

207

ADF Transfer Belt

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

208

ADF Separation Roller

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

5066

[PM Parts Display]

Display or does not display the “PM parts” button on the LCD.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: Not display

1: Display

5067

[Part Replacement Operation Type]

Selects the service maintenance or user maintenance for each PM parts. If the user service is selected, PM alert is displayed on the LCD

002

#Drum unit:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

003

#Development unit:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

011

Coating Bar:Bk

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

025

#Drum unit:C

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

026

#Development unit:C

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

048

#Drum unit:M

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

049

Development unit:M

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

071

#Drum unit:Y

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

072

#Development unit:Y

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

093

Image Transfer Unit

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

102

Image Transfer Cleaning Unit

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

109

Paper Transfer Roller Unit

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

115

Fusing unit

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

116

Fusing Roller unit

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

118

Pressure Roller

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

131

Filter Ozone Duct

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

132

Filter Heat Exhaust Duct

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

142

Wast Toner bottle

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

206

ADF Pick-up Roller

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

207

ADF Transfer Belt

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

208

ADF Separation Roller

*CTL

[0 or 1 / 0 / 1/step]

0: Service

1: User

5071

[Set Bypass Paper Size Display]

Turn on or off the paper size confirmation pop-up on the LED. This pop-up prevents mismatching between a paper size selected by the operation panel and an actual paper size on the by-pass tray.

001

-

CTL

[0 or 1 / 0 / 1/step]

0: Off

1: On

5073

[Supply Part Replacement Opration Type]

Selects ether User or Service manages supply parts.

001

Waste Tonner Bottle

*CTL

[0 or 1 / 0 / 1/step] 0:No Display 1:Display

5074

[Home Screen Login]

Sets the application that appears when the home key is pressed.

091

(0:OFF 1:SDK 2:Reserve)

*CTL

[0 to 2 / 0 / 1/step]

0: Function disable

1: SDK application

2: Legacy application (reserved)

092

Product ID

*CTL

[0x00 to 0xffff / - / 1/step]

Sets the Application product ID.

093

Application ID

*CTL

[0 to 255 / 0 / 1/step]

Sets the display category of the application that is specified in the SP5075-001,002.

5075

[USB Keyboard]

Sets the function of the external keyboard.

001

Function Setting

*CTL

[0 or 1 / 0 / 1/step]

0: Disable

1: Enable

5081

[ServiceSP Entery Code Setting]

DFU

001

ServiceSP Entery Code Setting

-

-

5083

[LED Light Switch Setting]

Turns LED lighting ON and OFF at Toner Near End.

001

Toner Near End

*CTL

[0 or 1 / 1 / 1/step]

0: OFF

1: ON

5114

[Optional Counter I/F]

001

MF Key Card Extension

*CTL

[0 or 1 / 0 / 1/step]

0: Not installed

1: Installed (scanning accounting)

5114

[Optional Counter I/F]

001

MF Key Card Extension

*CTL

[0 or 1 / 0 / 1/step]

0: Not installed

1: Installed (scanning accounting)

5114

[Optional Counter I/F]

001

MF Key Card Extension

*CTL

[0 or 1 / 0 / 1/step]

0: Not installed

1: Installed (scanning accounting)

5118

[Disable Copying]

This program disables copying.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: Not disabled

1: Disabled

5118

[Disable Copying]

This program disables copying.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: Not disabled

1: Disabled

5118

[Disable Copying]

This program disables copying.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: Not disabled

1: Disabled

5120

[Mode Clear Opt. Counter Removal]

This program updates the information on the optional counter. When you install or remove an optional counter, check the settings.

001

-

*CTL

[0 to 2 / 0 / 1/step]

0: Yes (removed)

1: Standby (installed but not used) 2: No (not removed)

5121

[Counter Up Timing]

This program specifies when the counter goes up. The settings refer to “paper feed” and “paper exit” respectively.

001

0:Feed 1:Exit

*CTL

[0 or 1 / 0 / 1/step]

0: Feed

1: Exit

5126

[Set F-size Document]

Larger the value, easier the detecting.

[0 to 2 / 0 / 1/step]

001

-

ENG

0: 8 1/2 x13

1: 8 1/4 x13

2: 8 x13

5127

[APS Mode]

This program disables the APS.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: Not disabled

1: Disabled

5131

[Paper Size Type Selection]

The program selects a paper size system from the following alternatives: the AB system (0), the LT system (1), and the AF system (2).

001

-

*ENG

[0 to 2 / 1 / 1/step]

0: JP (Japan)

1: NA

2: EU

5148

[Size Detection Off]

0: Detect

1: Not Detect

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

5150

[Bypass Length Setting]

Normally the paper length for sub scanning paper from the by-pass tray is limited to 600 mm, but this can be extended with this SP to 1260 mm.

Image quality is not assured for the length over 600mm.

When printing/feeding over 600mm length paper, customization request is required for a customized printer driver.

001

0: OFF 1: ON

CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

5162

[App. Switch Method]

Determines whether the application screen is switched with a hardware switch or software switch.

001

-

*CTL

[0 or 1 / 0 / 1/step] 0: Soft Key Set

1: Hard Key Set

5167

[Fax Printing Mode at Optional Counter Off]

Enables or disables the automatic print out without an accounting device. This SP is used when the receiving fax is accounted by an external accounting device.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: Automatic printing

1: No automatic printing

5169

[CE Login]

If you will change the printer bit switches, you must ‘log in’ to service mode with this SP before you go into the printer SP mode.

001

CE Login

*CTL

[0 or 1 / 0 / 1/step]

0: Disabled

1: Enabled

5181

[Size Adjust]

001

TRAY 1

*ENG

[0 to 3 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: A4 LEF

1: LT LEF

2: B5 LEF

3: A5 LEF

Fix size of tray 1 to appointed value 0: A4 LEF 1: LT LEF 2: B5 LEF 3: A5 LEF

002

TRAY 2: 1

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: A4 LEF

1: LT LEF

Detects size of tray 2 to appointed value preferentially. 0: A4 LEF 1: LT LEF

003

TRAY 2: 2

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: A3

1: DLT

Detects size of tray 2 to appointed value preferentially. 0: A3 1: DLT

004

TRAY 2: 3

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: B4

1: LG

Detects size of tray 2 to appointed value preferentially. 0: B4 1: LG

005

TRAY 2: 4

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: B5LEF

1: ExeLEF

Detects size of tray 2 to appointed value preferentially. 0: B5 LEF 1: Exe LEF

006

TRAY 2: 5

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: SRA3

1: 12X18

Detects size of tray 2 to appointed value preferentially. 0: SRA3 1: 12x18

007

TRAY 3/T-LCT: 1

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: A4LEF

1: LTLEF

Switches auto detection size of 3rd paper feed tray 1(LCT). 0: A4 LEF 1: LT LEF

008

TRAY 3: 2

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: A3

1: DLT

Switches auto detection size of 3rd paper feed tray 2. 0:

A3 1: DLT

009

TRAY 3: 3

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: B4

1: LG

Switches auto detection size of 3rd paper feed tray 3. 0:

B4 1: LG

010

TRAY 3: 4

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: B5LEF

1: ExeLEF

Switches auto detection size of 3rd paper feed tray 4. 0: B5 LEF 1: Exe LEF

011

TRAY 3: 5

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: 12.6X17.7

1: 12X18

Switches auto detection size of 3rd paper feed tray 5. 0: 12.6x17.7 1: 12x18

012

TRAY 4: 1

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: A4LEF

1: LTLEF

Switches auto detection size of 4th paper feed tray 1. 0:

A4 LEF 1:

LT LEF

013

TRAY 4: 2

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: A3

1: DLT

Switches auto detection size of 4th paper feed tray 2. 0:

A3 1: DLT

014

TRAY 4: 3

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: B4

1: LG

Switches auto detection size of 4th paper feed tray 3. 0: B4 1: LG

015

TRAY 4: 4

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: B5LEF

1: ExeLEF

Switches auto detection size of 4th paper feed tray 4. 0: B5 LEF 1: Exe LEF

016

TRAY 4: 5

*ENG

[0 or 1 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: 12.6X17.7

1: 12X18

Switches auto detection size of 4th paper feed tray 5. 0: 12.6x17.7 1: 12x18

017

LCT

*ENG

[0 to 2 / NA:1, EU, AS, CHN, TW,

KOR:0 / 1/step] 0: A4LEF

1: LTLEF

2: B5LEF

Switches auto detection size of Side set LCT 0: A4 LEF, 1: LT LEF 2: B5 LEF

5186

[RK4]

Sets whether to do the jam operation when pulling out RK4.

001

-

*ENG

[0 or 1 / 0 / 1/step]

5188

[Copy Nv Version]

Displays the version number of the NVRAM on the controller board.

001

-

*CTL

[- / - / -]

5193

[External Controller Info. Settings]

External controler settings.

001

-

CTL

[0 to 10 / 0 / 1/step]

0: External Controller is not installed

1: EFI

2: Ratio

3: Egret

4: GJ

5:Creo

6: QX-100

7: Kurofune

8 to 10: Reserved

5195

[Limitless SW]

Switches productivity precede limit less feed and use paper up limit less feed.

001

-

*CTL

[0 or 1 / 0 / 1/step]

0: Productivity Precede 1: Use paper up

5196

[Copier Vendor Mode]

-

001

90 deg. Rotation

CTL

[- / - / -]

002

Color and Tray Selection

CTL

[- / - / -]

5199

[Paper Exit After Staple End]

Enables or disables the paper feeding out from the finisher without stapling.

 If this setting is "1: ON", paper is fed out without stapling at the maximum number of the finisher stapling when the machine gets a multiple printing job (over maximum number).

 If this setting is "0: OFF", paper is fed out with stapling at the maximum number of the finisher stapling when the machine gets a multiple printing job (over maximum number).

001

0: OFF 1: ON

CTL

[ 0 or 1 / 0 / 1/step]

0: OFF,

1: ON

5212

[Page Numbering]

This program adjusts the position of the second side page numbers.

 "- value" moves the page number positions to the left edge.

 "+ value" moves the page number positions to the right edge.

003

Duplex Printout Right/Left Position

*CTL

[-10 to 10 / 0 / 1mm/step]

004

Duplex Printout High/Low Position

*CTL

[-10 to 10 / 0 / 1mm/step]

5227

[Page numbering]

201

Allow Page No. Entry

*CTL

[2 to 9 / 9 / 1/step]

Specify max. digits for “Job serial numbering start number” of optional text print.

202

Zero Surplus Stting

*CTL

[0 or 1 / 0 / 1/step] 0:OFF

1:ON

Specify zero suppress for “Job serial numbering start number” of optional text print.

5302

[Set Time]

Adjusts the RTC (real time clock) time setting for the local time zone. Examples: For Japan (+9 GMT), enter 540 (9 hours x 60 min.)

DOM: +540 (Tokyo)

NA: -300 (New York) EU: + 60 (Paris) CH: +480 (Beijing)

TW: +480 (Taipei)

AS: +480 (Hong Kong)

002

Time Difference

*CTL

[-1440 to 1440 / - / 1min./step]

5307

[Summer Time]

001

Setting

*CTL

[0 to 1 / - / 1/step] 0: Disabled

1: Enabled (Default)

1: NA and EUR

0: ASIA and others

Enables or disables the summer time mode.

 Make sure that both SP5-307-3 and -4 are correctly set. Otherwise, this SP is not activated even if this SP is set to "1".

003

Rule Set(Start)

*CTL

[0 to 0xffffffff / - / 1hex/step] (Default)

NA: 0x11100200 EUR: 0x10500100 ASIA: 0x03100000

Other: 0x00000000

Specifies the start setting for the summer time mode.

There are 8 digits in this SP. For months 1 to 9, the "0" cannot be input in the first digit, so the eight-digit setting for -2 or -3 becomes a seven-digit setting. 1st and 2nd digits: The month. [1 to 12]

3rd digit: The week of the month. [1 to 5]

4th digit: The day of the week. [0 to 6 = Sunday to Saturday] 5th and 6th digits: The hour. [00 to 23]

7th digit: The length of the advanced time. [0 to 9 / 1 hour /step] 8th digit: The length of the advanced time. [0 to 5 / 10 minutes /step]

 The digits are counted from the left.

 Make sure that SP5-307-1 is set to "1".

004

Rule Set (End)

-

-

Specifies the end setting for the summer time mode. There are 8 digits in this SP.

1st and 2nd digits: The month. [1 to 12] 3rd digit: The week of the month. [0 to 5]

4th digit: The day of the week. [0 to 7 = Sunday to Saturday] 5th and 6th digits: The hour. [00 to 23]

The 7th and 8 digits must be set to "00".

 The digits are counted from the left.

 Make sure that SP5-307-1 is set to "1".

5401

[Access Control]

230

SDK Certification Device

*CTL

[0 to 7 / 0 / power of 2/step]

0-1: SDK authentication available 0-0: Disable all functions

1-1: SKB Display

1-0: Disable

2-1: Administrator login

2-0: Disable

3 to 7-0: Reserved (set “0” only)

240

Detail Option

*CTL

[0 to 7 / 0x00 / 0x01/step]

0: Logout confirm option

-1: ON, 0: OFF

2 to 1: Auto-logout timer(retry timer)

-11: 30sec, 10: 20sec, 01: 10sec, 00: 60sec

3: personal authority / Group authority and operation

-1: ON, 0: OFF

4: Skip password entry

-1: ON, 0: OFF

5: Set the display of the remaining Frequence

-1: ON, 0: OFF

6 to 7: Set the display time

-1: ON, 0: OFF

5404

[User Code Count Clear]

004

-

*CTL

[- / - / -]

[Execute]

-

5404

[User Code Count Clear]

004

-

*CTL

[- / - / -]

[Execute]

-

5404

[User Code Count Clear]

004

-

*CTL

[- / - / -]

[Execute]

-

5411

[LDAP Certification]

004

Easy Certification

*CTL

[0 or 1 / 1 / 1/step]

1: On

0: Off

Determines whether easy LDAP certification is done.

005

Password Null Not Permit

*CTL

[0 or 1 / 0 / 1/step]

0: Password NULL not permitted. 1: Password NULL permitted.

This SP is referenced only when SP5411-4 is set to "1" (On).

006

Detail Option

*CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

Determines whether LDAP option (anonymous certification) is turned on or off.

5411

[LDAP Certification]

004

Easy Certification

*CTL

[0 or 1 / 1 / 1/step]

1: On

0: Off

Determines whether easy LDAP certification is done.

005

Password Null Not Permit

*CTL

[0 or 1 / 0 / 1/step]

0: Password NULL not permitted. 1: Password NULL permitted.

This SP is referenced only when SP5411-4 is set to "1" (On).

006

Detail Option

*CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

Determines whether LDAP option (anonymous certification) is turned on or off.

5411

[LDAP Certification]

004

Easy Certification

*CTL

[0 or 1 / 1 / 1/step]

1: On

0: Off

Determines whether easy LDAP certification is done.

005

Password Null Not Permit

*CTL

[0 or 1 / 0 / 1/step]

0: Password NULL not permitted. 1: Password NULL permitted.

This SP is referenced only when SP5411-4 is set to "1" (On).

006

Detail Option

*CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

Determines whether LDAP option (anonymous certification) is turned on or off.

5413

[Lockout Setting]

001

Lockout On/Off

*CTL

[0 or 1 / 0 / 1/step]

0: Off

1: On

Switches on/off the lock on the local address book account.

002

Lockout Threshold

*CTL

[1 to 10 / 5 / 1/step]

Sets a limit on the frequency of lockouts for account lockouts.

003

Cancellation On/Off

*CTL

[0 or 1 / 0 / 1/step]

0: Off (no wait time, lockout not cancelled)

1: On (system waits, cancels lockout if correct user ID and password are entered.

Determines whether the system waits the prescribed time for input of a correct user ID and password after an account lockout has occurred.

004

Cancellation Time

*CTL

[1 to 999 / 60 / 1 min./step]

Determines the length of time that the system waits for correct input of the user ID and password after a lockout has occurred. This setting is used only if SP5413-3 is set to "1" (on).

5414

[Access Mitigation]

001

Mitigation On/Off

*CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

Switches on/off masking of continuously used IDs and passwords that are identical.

002

Mitigation Time

*CTL

[0 to 60 / 15 / 1min./step]

Sets the length of time for excluding continuous access for identical user IDs and passwords.

5415

[Password Attack]

001

Permissible Number

*CTL

[0 to 100 / 30 / 1 attempt/step]

Sets the number of attempts to attack the system with random passwords to gain illegal access to the system.

002

Detect Time

*CTL

[1 to 10 / 5 / 1 sec./step]

Sets the time limit to stop a password attack once such an attack has been detected.

5416

[Access Information]

001

Access User Max Num

*CTL

[50 to 200 / 200 / 1 users/step]

Limits the number of users used by the access exclusion and password attack detection functions.

002

Access Password Max Num

*CTL

[50 to 200 / 200 / 1

password/step]

Limits the number of passwords used by the access exclusion and password attack detection functions.

003

Monitor Interval

*CTL

[1 to 10 / 3 / 1 sec./step]

Sets the processing time interval for referencing user ID and password information.

5417

[Access Attack]

001

Access Permissible Number

*CTL

[0 to 500 / 100 / 1/step]

Sets a limit on access attempts when an excessive number of attempts are detected for MFP features.

002

Attack Detect Time

*CTL

[10 to 30 / 10 / 1 sec./step]

Sets the length of time for monitoring the frequency of access to MFP features.

003

Productivity Fall Wait

*CTL

[0 to 9 / 3 / 1 sec./step]

Sets the wait time to slow down the speed of certification when an excessive number of access attempts have been detected.

004

Attack Max Num

*CTL

[50 to 200 / 200 / 1 attempt/step]

Sets a limit on the number of requests received for certification in order to slow down the certification speed when an excessive number of access attempts have been detected.

5420

[User Authentication]

This setting should be done by System Administrators.

001

Copy

*CTL

[0 to 1 / 0 / 1/step]

0: On

1: Off

Determines whether certification is required before a user can use the copy applications.

002

Color Security Setting

*CTL

[0x00 to 0xFF / 0x00 / 1/step]

011

DocumentServer

*CTL

[0 or 1/ 0 / 1/step]

0: On

1: Off

Determines whether certification is required before a user can use the document server.

021

Fax

*CTL

[0 or 1/ 0 / 1/step]

0: On

1: Off

Determines whether certification is required before a user can use the fax application.

031

Scanner

*CTL

[0 or 1/ 0 / 1/step]

0: On

1: Off

Determines whether certification is required before a user can use the scan applications.

041

Printer

*CTL

[0 or 1/ 0 / 1/step]

0: On

1: Off

Determines whether certification is required before a user can use the printer applications.

051

SDK1

*CTL

[0 or 1 / 0 / 1/step]

0: ON

061

SDK2

*CTL

071

SDK3

*CTL

1: OFF

5481

[Authentication Error Code]

These SP codes determine how the authentication failures are displayed.

001

System Log Disp

*CTL

[0 or 1 / 0 / 1/step]

0: Off

1: On

Determines whether an error code appears in the system log after a user authentication failure occurs.

002

Panel Disp

*CTL

[0 or 1 / 0 / 1/step]

1: On

0: Off

Determines whether an error code appears on the operation panel after a user authentication failure occurs.

5490

[MF KeyCard (Japan only)]

001

Job Permit Setting

*CTL

[0 to 1 / 0 / 1/step]

0: Disabled. Cancels operation without a user code.

1: Enabled. Allows operation without a user code.

Sets up operation of the machine with a keycard.

002

Count Mode Setting

*CTL

-

5501

[PM Alarm]

001

PM Alarm Level

*CTL

[0 to 9999 / 0 / 1/step]

0: Alarm off

1 to 9999: Alarm goes off when Value (1 to 9999) x 1000 > PM counter

5504

[Jam Alarm Interval]

001

-

*CTL

[0 to 3 / 3 / 1/step]

0: Z

1: L

2: M

3: H

Sets the alarm to sound for the specified jam level (document miss feeds are not included).

5505

[Error Alarm]

Sets the error alarm level.

The error alarm counter counts "1" when any SC is detected. However, the error alarm counter decreases by "1" when an SC is not detected during a set number of copied sheets (for example, default 700 sheets).

The error alarm occurs when the SC error alarm counter reaches "5".

001

Error Alarm

*CTL

[0 to 25500 / D146: 2500, D147:

3500, D148: 5000, D149: 6000,

D150: 7500 /undred/step]

0: Alarm Off

5507

[Supply/CC Alarm]

Enables or disables the notifying a supply call via the @Remote.

001

Paper Supply Alarm

*CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

002

Staple Supply Alarm

*CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

003

Toner Supply Alarm

*CTL

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

If you select "1" the alarm will sound when the copier detects toner end.

006

Toner Collection Bottle Alarm

*CTL

[0 or 1 / 0 / 1/step] 0:OFF

1: ON

080

Toner Call Timing

*CTL

[0 or 1 / 0 / 1/step]

0: At replacement

1: AtLessThanThresh

Changes the timing of the "Toner Supply Call" via the @Remote, when the following conditions occur.

081

Toner Call Threshold

*CTL

[10 or 90 / 0 / 10%/step]

128

Interval :Others

*CTL

[250 to 10000 / 1000 /

1page/step]

The "Paper Supply Call Level: nn" SPs specify the paper control call interval for the referenced paper sizes.

132

Interval :A3

*CTL

[250 to 10000 / 1000 /

1page/step]

The "Paper Supply Call Level: nn" SPs specify the paper control call interval for the referenced paper sizes.

133

Interval :A4

*CTL

[250 to 10000 / 1000 /

1page/step]

The "Paper Supply Call Level: nn" SPs specify the paper control call interval for the referenced paper sizes.

134

Interval :A5

*CTL

[250 to 10000 / 1000 /

1page/step]

The "Paper Supply Call Level: nn" SPs specify the paper control call interval for the referenced paper sizes.

141

Interval :B4

*CTL

[250 to 10000 / 1000 /

1page/step]

The "Paper Supply Call Level: nn" SPs specify the paper control call interval for the referenced paper sizes.

142

Interval :B5

*CTL

[250 to 10000 / 1000 /

1page/step]

The "Paper Supply Call Level: nn" SPs specify the paper control call interval for the referenced paper sizes.

160

Interval :DLT

*CTL

[250 to 10000 / 1000 /

1page/step]

The "Paper Supply Call Level: nn" SPs specify the paper control call interval for the referenced paper sizes.

166

Interval :LT

*CTL

[250 to 10000 / 1000 /

1page/step]

The "Paper Supply Call Level: nn" SPs specify the paper control call interval for the referenced paper sizes.

172

Interval :HLT

*CTL

[250 to 10000 / 1000 /

1page/step]

The "Paper Supply Call Level: nn" SPs specify the paper control call interval for the referenced paper sizes.

5508

[CC Call]

001

Jam Remains

*CTL

[0 or 1 / 1 / 1/step]

0: Disable

1: Enable

Enables/disables initiating a call for an unattended paper jam.

002

Continuous Jams

*CTL

[0 or 1 / 1 / 1/step]

0: Disable

1: Enable

Enables/disables initiating a call for consecutive paper jams.

003

Continuous Door Open

*CTL

[0 or 1 / 1 / 1/step]

0: Disable

1: Enable

Enables/disables initiating a call when the front door remains open.

011

Jam Detection: Time Length

*CTL

[3 to 30 / 10 / 1min./step]

Sets the time a jam must remain before it becomes an “unattended paper jam”. This setting is enabled only when SP5508-004 is set to "1".

012

Jam Detection: Continuous Count

*CTL

[2 to 10 / 5 / 1time/step]

Sets the number of consecutive paper jams required to initiate a call. This setting is enabled only when SP5508-004 is set to "1".

013

Door Open: Time Length

*CTL

[3 to 30 / 10 / 1min./step]

Sets the length of time the door remains open before the machine initiates a call. This setting is enabled only when SP5-508-004 is set to "1".

5515

[SC/Alarm Setting]

With @Remote in use, these SP codes can be set to issue an SC call when an SC error occurs. If this SP is switched off, the SC call is not issued when an SC error occurs.

001

SC Call

*CTL

[0 or 1 / 1 / 1/step]

0: OFF

1: ON

002

Service Parts Near End Call

*CTL

003

Service Parts End Call

*CTL

004

User Call

*CTL

006

Communication Test Call

*CTL

007

Machine Information Notice

*CTL

008

Alarm Notice

*CTL

009

Non Genuine Tonner Ararm

*CTL

010

Supply Automatic Ordering Call

*CTL

011

Supply Management Report Call

*CTL

012

Jam/Door Open Call

*CTL

5516

[Individual PM Part Alarm Call]

With @Remote in use, these SP codes can be set to issue an PM alarm call when one of SP parts reaches its yield.

001

Disable/Enable Setting (0: Not send, 1: Send)

*CTL

[0 or 1 / 1 / 1/step]

0: Not send

1: Send

004

Percent yield for triggering PM alert

*CTL

[1 to 255 / 75 / 1 %/step]

5517

[Get Machine Information]

031

Get SMC Info Retry Internal

*CTL

[10 to 255 / 10 / 1min/step]

When SMC info collect is interrupt, retries during the time between receving Request for obtaining SMC info, to value set with this setting.

5610

[Base Gamma Ctrl Pt:Execute]

004

Get Factory Default

ENG

[0 or 1 / 0 / 1/step]

Factoryreset the ACC execution result (create base gamma with factory adjusted value).

005

Set Factory Default

ENG

[0 or 1 / 0 / 1/step]

Overwrites the factory adjusted value with base gamma control point (current value).

006

Restore Orginal Value

ENG

[0 or 1 / 0 / 1/step]

Reset the ACC execution result (create base gamma with last adjusted value).

5611

[Toner Color in 2C]

001

B-C

*ENG

[0 to 128 / 100 / 1/step]

Adjust (no correction: 100) output color (C component) from 0(%) to 128(%) when setting basic color (blue) to single color.

002

B-M

*ENG

[0 to 128 / 100 / 1/step]

Adjust (no correction: 100) output color (M component) from 0(%) to 128(%) when setting basic color (blue) to single color.

003

G-C

*ENG

[0 to 128 / 100 / 1/step]

Adjust (no correction: 100) output color (C component) from 0(%) to 128(%) when setting basic color (green) to single color.

004

G-Y

*ENG

[0 to 128 / 100 / 1/step]

Adjust (no correction: 100) output color (Y component) from 0(%) to 128(%) when setting basic color (green) to single color.

005

R-M

*ENG

[0 to 128 / 100 / 1/step]

Adjust (no correction: 100) output color (M component) from 0(%) to 128(%) when setting basic color (red) to single color.

006

R-Y

*ENG

[0 to 128 / 100 / 1/step]

Adjust (no correction: 100) output color (Y component) from 0(%) to 128(%) when setting basic color (red) to single color.

5618

[Color Mode Display Selection]

001

-

*CTL

[0 or 1 / 1 / 1/step]

0: ACS, Color, Black & White, Two Colors, Single colour

1: ACD, Full Color, Black & White

Selects the color selection display on the LCD.

5730

[Extended Function Setting]

-

001

JavaTM Platform setting

*CTL

[1 to 24 char. / NULL / -]

Input license codes to set JavaVM enabled / disabled.

002

JavaTM Platform display

*CTL

[Read Only / 1 / -] 1(enable)[FIXED]

Check whether JavaVM is enable of not.

010

Expiration Prior Alarm Set

*CTL

[0 to 999 / 20 / 1day/step]

5745

[PowerConsumption]

211

Controller Standby

*CTL

[0 to 9999 / 0 / 1/step]

212

STR

*CTL

[0 to 9999 / 0 / 1/step]

213

Main Power Off

*CTL

[0 to 9999 / 0 / 1/step]

214

Scanning and Printing

*CTL

[0 to 9999 / 0 / 1/step]

215

Printing

*CTL

[0 to 9999 / 0 / 1/step]

216

Scanning

*CTL

[0 to 9999 / 0 / 1/step]

217

Engine Standby

*CTL

[0 to 9999 / 0 / 1/step]

218

Low Power Consumption

*CTL

[0 to 9999 / 0 / 1/step]

219

Silent Consumption

*CTL

[0 to 9999 / 0 / 1/step]

220

Heater Off

*CTL

[0 to 9999 / 0 / 1/step]

5747

[Browser Setting]

-

201

JPEG Quality

*CTL

[0 to 100 / 80 / 1%/step]

203

memory

*CTL

[0 or 1 / 0 / 1/step ]

0: Use extended memory

1: Not use extended memory

204

Vertical Scroll Display Setting

*CTL

[0 or 1 / 0 / 1/step]

207

Browser4

CTL

[0 to 255 / 0 / 1/step]

208

Browser5

CTL

[0 to 255 / 0 / 1/step]

209

Browser6

CTL

[0 to 255 / 0 / 1/step]

210

Browser7

CTL

[0 to 255 / 0 / 1/step]

211

Browser8

CTL

[0 to 255 / 0 / 1/step]

212

Browser9

CTL

[0 to 255 / 0 / 1/step]

213

Browser10

CTL

[char. code + 0-255 bytechar. /

NULL / -]

5749

[Import/Export]

Imports and exports preference information.

001

Export

CTL

[- / - / -]

Target: System, Printer, Fax, Scanner

Option: Unique, Secret Copy config: Encryption, Encryption key(if selected) [Execute]

101

Import

CTL

[- / - / -]

Option: Unique

Copy config: Encryption, Encryption key(if selected) [Execute]

5752

[Copy FlairAPIFunction Setting]

CopyFlairAPI Function enable / disable.

001

Copy FlairAPIFunction Setting

*CTL

* see BitSwitch below:

bit

Setting

meanings

Description

0

1

bit 0

Start of FlairAPI Server

Off (Do not Start)

On (Start)

Sets whether to start exclusive FlairAPI http server. If it is 0, scanning FlairAPI function and simple UI function will be disabled. The machine installed Android operating panel option, set “1”, others set “0”.

bit 1

Access permission of FlairAPI from outside of the machine

Disabled

Enabled

If it is “0”, accessing is limited from the machine only, such as operating panel, SDK/J, MFP browsers etc... If it is “1”, accessing is allowed from outside of FlairAPI such as PC, Remote UI, IT-Box etc...

bit 2

Reserved

-

-

-

bit 3

Reserved

-

-

-

bit 4

Simple UI Function

Disabled

Enabled

If it is “1”, the machine can be used Scanner Simple UI. If it is “0”, requesting URL of Simple UI returns “404 Not Found”

bit 5

Accessing permission of Simple UI from outside of the machine

Disabled

Enabled

If it is “0”, accessing is limited from the machine only (operating panel and MFP browser). If it is “1”, accessing is allowed from outside of Simple UI such as PC, mobile devices, and so on.

bit 6

Reserved

-

-

-

bit 7

Reserved

-

-

-

5801

[Memory Clear]

001

All Clear

CTL

[- / - / -]

[Execute]

Resets all correction data for process control and all software counters, and returns all modes and adjustments to their default values.

5801

[Memory Clear]

001

All Clear

CTL

[- / - / -]

[Execute]

Resets all correction data for process control and all software counters, and returns all modes and adjustments to their default values.

5801

[Memory Clear]

001

All Clear

CTL

[- / - / -]

[Execute]

Resets all correction data for process control and all software counters, and returns all modes and adjustments to their default values.

5801

[Memory Clear]

002

Engine

ENG

[- / - / -]

[Execute]

Clears non-volatile memory of engine.

5801

[Memory Clear]

002

Engine

ENG

[- / - / -]

[Execute]

Clears non-volatile memory of engine.

5801

[Memory Clear]

002

Engine

ENG

[- / - / -]

[Execute]

Clears non-volatile memory of engine.

5801

[Memory Clear]

Select following SPs and press [Execute] on LCD. After executing, reboot the machine.

003

SCS

CTL

[- / - / -]

[Execute]

Initializes default system settings, SCS (System Control Service) settings, operation display coordinates, and ROM update information.

004

IMH Memory Clr

CTL

[- / - / -]

[Execute]

Initializes the IMH settings.

005

Mcs

CTL

[- / - / -]

[Execute]

Initializes the Mcs settings.

006

Copier Application

CTL

[- / - / -]

[Execute]

Initializes all copier application settings.

007

Fax Application

CTL

[- / - / -]

[Execute]

Initializes the fax reset time, job login ID, all TX/RX settings, local storage file numbers, and off-hook timer.

008

Printer Application

CTL

[- / - / -]

[Execute]

The following service settings:

 Bit switches

 Gamma settings (User & Service)

 Toner Limit

The following user settings:

 Tray Priority

 Menu Protect

 System Setting except for setting of Energy Saver

 I/F Setup (I/O Buffer and I/O Timeout)

 PCL Menu

009

Scanner Application

CTL

[- / - / -]

[Execute]

Initializes the scanner defaults for the scanner and all the scanner SP modes.

Deletes the network file application management files and thumbnails, and initializes the job login ID.

010

Web Service

CTL

[- / - / -]

[Execute]

Deletes the network file application management files and thumbnails, and initializes the job login ID.

011

NCS

CTL

[- / - / -]

[Execute]

All setting of Network Setup (User Menu) (NCS: Network Control Service)

012

R-Fax

CTL

[- / - / -]

[Execute]

Initializes the job login ID, SmartDeviceMonitor for Admin, job history, and local storage file numbers.

014

Clear DCS Setting

CTL

[- / - / -]

[Execute]

Initializes the DCS (Delivery Control Service) settings.

015

Clear UCS Setting

CTL

[- / - / -]

[Execute]

Initializes the UCS (User Information Control Service) settings.

016

MIRS Memory Clr

CTL

[- / - / -]

[Execute]

Initializes the MIRS (Machine Information Report Service) settings.

017

CCS

CTL

[- / - / -]

[Execute]

Initializes the CCS (Certification and Charge-control Service) settings.

018

SRM Memory Clr

CTL

[- / - / -]

[Execute]

Initializes the SRM (System Resource Manager) settings.

019

LCS Memory Clr

CTL

[- / - / -]

[Execute]

Initializes the LCS settings.

020

Web Uapli

CTL

[- / - / -]

[Execute]

Initializes the web user application settings.

021

ECS

CTL

[- / - / -]

[Execute]

Initializes the ECS settings.

024

BROWSER

CTL

[- / - / -]

[Execute]

Initializes the browser settings.

5803

[INPUT Check]

See page 3-1

5804

[OUTPUT Check]

See page 3-31

5805

[Anti-Condensation Heater]

Switches ON/OFF dehumidify heater / dew condensation preventing heater during standby.

0: OFF... Switches OFF when standby (default setting) 1: ON... Switches ON when standby

001

0:OFF / 1:ON

*ENG

[0 or 1 / 0 / 1/step]

0: OFF... Switches OFF when standby (default setting)

1: ON... Switches ON when standby

5810

[SC Reset]

001

Fusing SC Reset

*ENG

[0 or 1 / 0 / 1/step]

002

Hard High Temp. Detection

*ENG

[0 or 1 / 0 / 1/step]

5811

[MachineSerial]

002

Display

*ENG

[0 to 255 / 0 / 1/step]

Displays serial number.

5811

[MachineSerial Set]

004

BCU

*ENG

[0 to 255 / 0 / 1/step]

Displays/Enters serial number of BCU:FROM Same as SP5-811-001.

5812

[Service Tel. No. Setting]

001

Service

*CTL

[up to 20 / - / 1/step]

Sets the telephone number for a service representative. This number is printed on the Counter List, which can be printed with the user’s “Counter” menu.

This can be up to 20 characters (both numbers and alphabetic characters can be input).

002

Facsimile

*CTL

[up to 20 / - / 1/step]

Sets the fax or telephone number for a service representative. This number is printed on the Counter List.

This can be up to 20 characters (both numbers and alphabetic characters can be input).

003

Supply

*CTL

[up to 20 / - / 1/step]

Use this to input the telephone number of your supplier for consumables. Enter the number and press #.

004

Operation

*CTL

[up to 20 / - / 1/step]

Use this to input the telephone number of your sales agency. Enter the number and press #.

5816

[Remote Service]

001

I/F Setting

*CTL

[0 to 2 / 2 / 1/step]

0: Remote service off

1: CSS remote service on 2: NRS remote service on

Selects the remote service setting.

002

CE Call

*CTL

[0 or 1 / 0 / 1/step]

0: Start of the service 1: End of the service

Performs the CE Call at the start or end of the service.

 This SP is activated only when SP 5816-001 is set to “2”.

003

Function Flag

*CTL

[0 or 1 / 0 / 1/step]

0: Disabled

1: Enabled

Enables or disables the remote service function.

007

SSL Disable

*CTL

[0 or 1 / 0 / 1/step]

0: Yes. SSL not used. 1: No. SSL used.

Controls if RCG (Remote Communication Gate) confirmation is done by SSL during an RCG send for the @Remote over a network interface.

008

RCG Connect Timeout

*CTL

[1 to 90 / 30 / 1second/step]

Sets the length of time (seconds) for the time-out when the RCG (Remote Communication Gate) connects during a call via the @Remote network.

008

RCG Connect Timeout

*CTL

[1 to 90 / 30 / 1second/step]

Sets the length of time (seconds) for the time-out when the RCG (Remote Communication Gate) connects during a call via the @Remote network.

009

RCG Write Timeout

*CTL

[0 to 100 / 60 / 1second/step]

Sets the length of time (seconds) for the time-out when the RCG (Remote Communication Gate) connects during a call via the @Remote network.

010

RCG Read Timeout

*CTL

[0 to 100 / 60 / 1second/step]

Sets the length of time (seconds) for the timeout when sent data is written from the RCG during a call over the @Remote network.

011

Port 80 Enable

*CTL

[0 or 1 / 0 / 1/step]

0: No. Access denied 1: Yes. Access granted.

Controls if permission is given to get access to the SOAP method over Port 80 on the @Remote network.

013

RFU Timing

*CTL

[0 or 1 / 1 / 1/step]

0: Any status of a target machine 1: Sleep or panel off mode only

Selects the timing for the remote firmware updating.

014

RCG Error Cause

CTL

[0 or 1 / 0 / 1/step]

0: Initial state, normal condition 1: Error

Displays RCG connection error. cause

021

RCG – C Registed

*CTL

[0 or 1 / 0 / 1/step]

0: Installation not completed 1: Installation completed

This SP displays and selects the RCG-N connection method.

023

connect type(N/M)

*CTL

[0 or 1 / 0 / 1/step]

0: internet connection

1: Dial-up connection

Displays the connection type of the NRS G/W and Cumin.

The value will be changed after installation completed in the case of dial-up connection.

061

Cert Expire Timing

*CTL

[0 to 0xffffffff / 0 / 1/step] 0: Not use

1: Use

Sets the date for expiration notification.

062

Use Proxy

*CTL

[0 or 1 / 0 / 1/step]

0: Not use

1: Use

This SP setting determines if the proxy server is used when the machine communicates with the service center.

063

Proxy Host

*CTL

[- / - / -]

This SP sets the address of the proxy server used for communication between the RCG device and the gateway. Use this SP to set up or display the customer proxy server address.

The address is necessary to set up the embedded RCG-N.

 The address display is limited to 128 characters. Characters beyond the 128 character are ignored.

 This address is customer information and is not printed in the SMC report.

064

Proxy PortNumber

*CTL

[0 to 0xffff / 0 / 1/step]

This SP sets the port number of the proxy server used for communication between the embedded RCG-N and the gateway. This setting is necessary to set up the embedded RC Gate-N.

 This port number is customer information and is not printed in the SMC report.

065

Proxy User Name

*CTL

[up to 31 / - / 1/step]

This SP sets the HTTP proxy certification user name. The length of the name is limited to 31 characters. Any character beyond the 31st character is ignored.

 This name is customer information and is not printed in the SMC report.

066

Proxy Password

*CTL

[up to 31 / - / 1/step]

This SP sets the HTTP proxy certification password.

 The length of the password is limited to 31 characters. Any character beyond the 31st character is ignored.

 This name is customer information and is not printed in the SMC report.

067

Proxy Password

*CTL

[0 to 255 / 0 / 1/step]

Displays status of the certification used for Cumin.

If it is not installed as Cumin, the value of this SP will be set when it installed, after checking the certification status.

0

The certification adequately set on the machine.

1

Request for certification update in progress.

2

Certification Update completed and notification of the success status to the G/W in progress.

3

Certification Update failed and notification of the result to the G/W in progress.

4

Certification expiration date will be coming soon. Notifying the G/W to request for certification update.

11

Rescue certification setting for connecting to the rescue G/W in progress because update for rescue certification needed.

12

Setting for rescue certification has completed. Requesting to the rescue G/W for updating certification.

13

Notification for certification updating request has completed. Waiting for the certification update request from the rescue G/W.

14

Received the notification for certification updating request from the rescue G/W. Writing the certification.

15

Writing the certification has completed. Notifying the result of certification update to the G/W.

16

Writing the certification has failed. Notifying the result of certification update to the G/W.

17

Writing a rescue certification because received a certification error again after completed the certification update request from the G/W and noticed the result of certification update with the updated certification.

18

The writing operation mentioned in #17 has completed. Notifying the result of certification update to the rescue G/W.

068

CERT: Error

*CTL

[0 to 255 / 0 / 1/step]

Displays a number code that describes the reason for the request for update of the certification.

0

Normal. There is no request for certification update in progress.

1

Request for certification update in progress. The current certification has expired.

2

An SSL error notification has been issued. Issued after the certification has expired.

3

Notification of shift from a common authentication to an individual certification.

4

Notification of a common certification without ID2.

5

Notification that no certification was issued.

6

Notification that GW URL does not exist.

069

CERT: Up ID

*CTL

[- / - / -]

-

083

Firm Up Status

*CTL

[0 to 5 / 0 / 1/step]

0: Waiting for accepting firm update

1: Waiting for firm update start schedule

2: Waiting for user confirmation 3: In preparation for the machine firm update

4: processing the machine firm update

5: processing the closing operation of the machine firm update

085

Firm Up User Check

CTL

[- / - / -]

This SP setting determines if the operator can confirm the previous version of the firmware before the firmware update execution. If the option to confirm the previous version is selected, a notification is sent to the system manager and the firmware update is done with the firmware files from the URL.

086

Firmware Size

CTL

[- / - / -]

Allows the service technician to confirm the size of the firmware data files during the firmware update execution.

087

CERT:Macro Ver.

CTL

[8digits / - / 1digit/step]

Displays the macro version of the @Remote certification. This SP displays 8-digit characters.

088

CERT:PAC Ver.

CTL

[16digits / - / 1digit/step]

Displays the PAC version of the @Remote certification. This SP displays 16-digit characters.

089

CERT:ID2Code

CTL

[17digits / - / 1digit/step]

Displays ID2 for the @Remote certification. Spaces are displayed as underscores (_). Asterisks (****) indicate that no @Remote certification exists. This SP displays 17-digit characters.

090

CERT:Subject

CTL

[17digits / - / 1digit/step]

Displays the common name of the @Remote certification subject. CN = the following 17 bytes. Spaces are displayed as underscores (_). Asterisks (****) indicate that no DESS exists.

091

CERT:Serial No.

CTL

[16digits / - / 1digit/step]

Displays serial number for the NRS certification. Asterisks (****) indicate that no DESS exists. This SP displays 16-digit characters

092

CERT:Issuer

CTL

[30digits / - / 1digit/step]

Displays the common name of the issuer of the @Remote certification. CN = the following 30 bytes. Asterisks (****)indicate that no DESS exists.

093

CERT:Valid Start

CTL

[10digits / - / 1digit/step]

Displays the start time of the period for which the current @Remote certification is enabled. This SP displays 10-digit characters.

094

CERT:Valid End

CTL

[10digits / - / 1digit/step]

Displays the end time of the period for which the current @Remote certification is enabled. This SP displays 10-digit characters.

102

CERT:Encrypt Level

*CTL

[1 to 2 / 1 / 1/step]

Displays the encryption strength of NRS certification.

150

Selection Country

CTL

[0 to 10 / 1 / 1/step]

0: Japan

1: USA

2: Canada

3: UK

4: Germany

5: France

6: Italy

7: Netherlands

8: Belgium

9: Luxembourg

10: Spain

Select the country where embedded RCG-M is installed in the machine. After selecting the country, you must also set the following SP codes for embedded RCG-M:

 SP5816-153

 SP5816-154

 SP5816-161

151

Line Type AutomaticJudgment

CTL

[- / - / -]

[Execute]

Press [Execute].

Setting this SP classifies the telephone line where embedded RCG-M is connected as either dial-up (pulse dial) or push (DTMF tone) type, so embedded RCG-M can automatically distinguish the number that connects to the outside line.

152

Line Type Judgment Result

CTL

[0 to 9 / - / 1/step]

Displays a number to show the result of the execution of SP5816 151. Here is a list of what the numbers mean.

0: Success

1: In progress (no result yet). Please wait. 2: Line abnormal

3: Cannot detect dial tone automatically 4: Line is disconnected

5: Insufficient electrical power supply 6: Line classification not supported

7: Error because fax transmission in progress – ioctl() occurred. 8: Other error occurred

9: Line classification still in progress. Please wait.

153

Selection Dial / Push

CTL

[0 or 1 / 0 / 1 /step]

0: Tone Dialing Phone 1: Pulse Dialing Phone

Inside Japan "2" may also be displayed:

0: Tone Dialing Phone

1: Pulse Dialing Phone 10PPS 2: Pulse Dialing Phone 20PPS

This SP displays the classification (tone or pulse) of the telephone line to the access point for embedded RCG-M. The number displayed (0 or 1) is the result of the execution of SP5816-151. However, this setting can also be changed manually.

154

Outside Line Outgoing Number

CTL

[- / - / -]

The SP sets the number that switches to PSTN for the outside connection for embedded RCG-M in a system that employs a PBX (internal line).

 If the execution of SP5816-151 has succeeded and embedded RCG-M has connected to the external line, this SP display is completely blank.

 If embedded RCG-M has connected to an internal line, then the number of the connection to the external line is displayed.

 If embedded RCG-M has connected to an external line, a comma is displayed with the number. The comma is inserted for a 2 sec. pause.

The number setting for the external line can be entered manually (including commas).

156

Dial Up User Name

CTL

[up to 32 / - / 1/step]

Use this SP to set a user name for access to remote dial up. Follow these rules when setting a user name:

 Name length: Up to 32 characters

 Spaces and # allowed but the entire entry must be enclosed by double quotation marks (").

157

Dial Up Password

CTL

[up to 32 / - / 1/step]

Use this SP to set a password for access to remote dial up. Follow these rules when setting a user name:

 Name length: Up to 32 characters

 Spaces and # allowed but the entire entry must be enclosed by double quotation marks (").

161

Local Phone Number

CTL

[up to 24 / - / 1/step]

Use this SP to set the telephone number of the line where embedded RCG-M is connected. This number is transmitted to and used by the Call Center to return calls.

Limit: 24 numbers (numbers only)

162

Connection Timing Adjustment Incoming

CTL

[0 to 24 / 1 / 1/step]

When the Call Center calls out to an embedded RCG-M modem, it sends a repeating ID tone (*#1#). This SP sets the time the line remains open to send these ID tones after the number of the embedded RCG-M modem is dialed up and connected.

The actual amount of time is this setting x 2 sec. For example, if you set "2" the line will remain open for 4 sec.

163

Access Point

CTL

[0 to 16 / 0 / 1/step]

This is the number of the dial-up access point for RCG-M. If no setting is done for this SP code, then a preset value (determined by the country selected) is used.

Default: 0

Allowed: Up to 16 alphanumeric characters

164

Line Connecting

CTL

[0 to 1 / 0 / 1/step]

0: Sharing Fax

1: No Sharing Fax

This SP sets the connection conditions for the customer. This setting dedicates the line to RCG-M only, or sets the line for sharing between RCG-M and a fax unit.

 If this setting is changed, the copier must be cycled off and on.

 SP5816 187 determines whether the off-hook button can be used to interrupt a RCG-M transmission in progress to open the line for fax transaction.

173

Modem Serial No.

CTL

[- / - / -]

This SP displays the serial number registered for the RCG-M.

174

Retransmission Limit

CTL

[- / - / -]

Normally, it is best to allow unlimited time for certification and ID2 update requests, and for the notification that the certification has been completed. However, RCG-M generates charges based on transmission time for the customer, so a limit is placed upon the time allowed for these transactions.

If these transactions cannot be completed within the allowed time, do this SP to cancel the time restriction.

187

FAX TX Priority

CTL

[0 or 1/ 0 / 1/step]

0: Disable

1: Enable

This SP determines whether pushing the off-hook button will interrupt a RCG-M transmission in progress to open the line for fax transaction. This SP can be used only if SP5816 164 is set to "0".

200

Manual Polling

CTL

[- / - / -]

[Execute]

Performs center polling when executed.

201

Regist Status

CTL

[0 to 4 / 0 / 1/step] [Execute]

Displays the installation status as the target of NRS services.

0

Not installed as NRS machines or Cumin.

1

Installing as Cumin. Box enrollment has completed. Unable to response for the machine serching from Basil at this status.

2

Installation has completed. Unable to response for the machine serching from Basil at this status.

3

As a NRS machine, installation has completed. It cannot install as Cumin.

4

NRS modules is not being launched.

202

Letter Number

*CTL

[- / - / -]

Sets the request number that is required to install Cumin.

203

Confirm Ececute

*CTL

[- / - / -]

[Execute]

Executes the request number inquiry to NRS G/W.

204

Confirm Result

CTL

[0 to 255 / 0 / 1/step]

0: Success Inquiry

1: Request number error

3: Communication error (Enabled Proxy)

4: Communication error (Disabled Proxy)

5: Proxy error (failed auth.) 6: Communication error

8: Other error (See SP5-816-208 for detail)

9: Processing inquiry 20: Failed Dial-up auth.

21: Failed answer tone detection 22: Failed career detection

23: Invalid modem value

24: Shortage of electrical current 25: Cable disconnected

26: Line occupied

Displays the result of SP5-816-203.

205

Confirm Place

CTL

[0 to 255 / 0 / 1/step]

0: Success registration 1: Request number error

3: Communication error (Enabled Proxy)

4: Communication error (Disabled Proxy)

5: Proxy error (failed auth.) 6: Communication error

8: Other error (See SP5-816-208 for detail)

9: Processing registration 20: Failed Dial-up auth.

21: Failed answer tone detection 22: Failed career detection

23: Invalid modem value

24: Shortage of electrical current 25: Cable disconnected

26: Line occupied

Displays the installed section informed from G/W for response of request number inquiry if the section is enrolled on the G/W.

206

Register Execute

CTL

[- / - / -]

[Execute]

Executes the registration of Cumin.

207

Register Result

CTL

[0 to 255 / 0 / 1/step]

Displays the registration result. Shows the executed status of SP5-816-206.

208

Error Code

CTL

[-2147483647 to 2147483647 / 0 /

-]

Displays the registration result of SP5-816-204.

208

Invalid modem parameter

-11001

Chat parameter error.

-11002

Chat execution error.

-11003

Unexpected error

-11004

Disconnect operation occurred during modem communication,

-11005

NCS reboot occurred during modem communication.

208

Errors with invalid procedure or settings

-12002

Attempted to inquiry or registration without obtaining the installation status.

-12003

Attempted to registrate without inquiry despite un-registered status.

-12004

Attempted to install with invalid certification, ID2, and without input the machine number.

-12005

Executed inquiry/ registration in a invalid Cumin function and prohibited @Remote communication.

208

-12006

Attempted to inquiry in BOX registration completed.

-12007

Registration attempted with the different request number from the number used for the last inquiry.

-12008

Certificaton update failed because Job processing etc.

-12009

Mismatched between ID2 in NR-RAM and ID2 in the individual certification.

-12010

Not initialized the certification area.

208

Error with error response from G/W

-2385

Inappropriate international dialing prefix

-2387

Not supported in the center.

-2389

DB failure

-2390

Program failure

-2391

Double registration of the machine

208

-2392

Parameter error

-2393

Not managed Basil

-2394

Not managed machine

-2395

Invalid BOX ID of Basil

-2396

Invalid Devic ID of Basil

-2397

Different format of ID2 (includes invalid ID2)

-2398

Different format of request number

209

CommLog Print

CTL

[- / - / -]

Releases the machine from its embedded RCG setup.