4008

[Sub Scan Magnification Adj]

Adjusts Sub Scan Magnification by 0.1% each step.

001

-

*ENG

[-1.0 to 1.0 / 0.0 / 0.1 %/step] Picture will stretch as value increases.

Picture will shrink as value decreases.

4010

[Sub Scan Registration Adj]

Adjusts Sub Scan Registration position of book scanner by 0.1mm each step.

001

-

*ENG

[-2.0 to 2.0 / 0.0 / 0.1 mm/step] Picture will move to back edge of sub scan as value increases.

Picture will move to front edge of sub scan as value decreases.

4011

[Main Scan Reg]

Adjust Main Scan Registration position by 0.1mm each step.

001

-

*ENG

[-2.5 to 2.5 / 0.0 / 0.1 mm/step] Picture moves to right as value increases.

Picture moves to left as value decreases.

4012

[Set Scale Mask]

Adjusts scanning margins for the leading and trailing edges (sub scan) and right and left edge (main scan).

 Do not adjust unless the customer desires a scanner margin greater than the printer margin. These settings are adjusted to erase shadows caused by the gap between the original and the scale of the scanner unit.

001

Book:Sub LEdge

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase scale shadow of sub scan leading edge (left side or original table) when scanning with book scanner.

002

Book:Sub TEdge

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase scale shadow of sub scan trailing edge (right side or original table) when scanning with book scanner.

003

Book:Main:LEdge

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase scale shadow of main scan leading edge (rear side or original table) when scanning with book scanner.

004

Book:Main:TEdge

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase scale shadow of main scan trailing edge (front side or original table) when scanning with book scanner.

005

ADF: Leading Edge

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase scale shadow of sub scan leading edge when scanning with ADF.

007

ADF: Right

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase scale shadow of main scan leading edge when scanning with ADF.

008

ADF: left

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase scale shadow of main scan trailing edge when scanning with ADF.

4013

[Scanner Free Run]

 Scan operation amount will depend of the latest scanning size

001

Book mode :Lamp Off

ENG

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

Repeats carriage reciprocating motion with lamp off.

002

Book mode :Lamp On

ENG

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

Repeats carriage reciprocating motion with lamp on.

4014

[Scan]

001

HP Detection Enable

ENG

[0 or 1 / 0 / 1/step] 0:OFF, 1:ON

Runs Scanner (HP Detection Enable).

Reading size, speed is same as the most recent run(Default is FC, A3, Actual size)

002

HP Detection Disable

ENG

[0 or 1 / 0 / 1/step] 0:OFF, 1:ON

Runs Scanner (HP Detection Disable).

Reading size, speed is same as the most recent run(Default is FC, A3, Actual size)

4020

[Dust Check]

001

Dust Detect:On/Off

*ENG

[0 or 1 / 0 / 1/step]

0: OFF, 1: ON

Sets DF Dust Detection ON/OFF.

002

Dust Detect:Lvl

*ENG

[0 to 8 / 4 / 1/step]

0: lowest detection level 8: highest detection level

Sets DF Dust Detect Level. Easier to Detect as Value increases.

4020

[Dust Check Lvl]

003

Dust Reject:Lvl

*ENG

[0 to 4 / 0 / 1/step]

Sets ON/OFF and switches level of Vertical stripes correction. 0=OFF, sets level to 1 from 4. Stronger correction as value increases.

4020

[DF Dust Check]

011

Dust Detect Level:Rear

*ENG

[0 or 1 / 0 / 1/step]

0: OFF, 1: ON

Sets ON/OFF DF: Rear dust detection setting.

012

Correction Level:Rear

*ENG

[0 to 8 / 4 / 1/step] 0:Lowest level 8:Highest level

Sets DF: Rear dust detection level. As the value enlarges, easier to detect.

4201

[LoCPP edge level:K]

001

600dpi 2bit edge1

*ENG

[0 to 15 / 11 / 1/step]

Value increase: Tonner adhesion amount will increase for Bk picture edge.

Toner decrease: Toner adhesion amount will decrease for Bk picture edge.

Upper limit threshold parameter for smaller edge: 600dpi 2bit

002

600dpi 2bit edge23

*ENG

[0 to 15 / 11 / 1/step]

Value increase: Tonner adhesion amount will increase for Bk picture edge.

Toner decrease: Toner adhesion amount will decrease for Bk picture edge

Upper limit threshold parameter for larger edge: 600dpi 2bit

003

600dpi 4bit edge1

*ENG

[0 to 15 / 11 / 1/step]

Value increase: Tonner adhesion amount will increase for Bk picture edge.

Toner decrease: Toner adhesion amount will decrease for Bk picture edge.

Upper limit threshold parameter for smaller edge: 600dpi 4bit

004

600dpi 4bit edge23

*ENG

[0 to 15 / 11 / 1/step]

Value increase: Tonner adhesion amount will increase for Bk picture edge.

Toner decrease: Toner adhesion amount will decrease for Bk picture edge.

Upper limit threshold parameter for larger edge: 600dpi 4bit

4201

[LoCPP edge off/on:K]

Off/on for Smaller/larger edge: 1200dpi 1bit

011

1200dpi 1bit edge12

*ENG

[0 or 1 / 0 / 1/step]

ON/OFF for smaller edge: 1200dpi 1bit

Select ON/OFF for low CPP edge correction with 1200dpi 1bit.

012

1200dpi 1bit edge345

*ENG

[0 or 1 / 0 / 1/step]

ON/OFF for larger edge: 1200dpi 1bit

Select ON/OFF for low CPP edge correction with 1200dpi 1bit.

4301

[Operation Check APS Sensor]

001

Operation Check APS Sensor

*ENG

[0 to 255 / 0 / 1/step]

0: Not detected

1: Detected

SP for testing APS Sensor function.

4303

[Min Size for APS]

001

Min Size for APS

*ENG

[0 or 1 / 0 / 1/step] 0 : No Original

1: A5-Lengthwise

Sets display when non-standard (small size) size original is detected.

 Sets display when non-standard (small size) size original is detected.

 When “2:EU” is selected at SP5-131-001 and “3:8K 16K” with SP4-305-001, Decision of SP4-303-001 will be “1:16K Vertical”

4305

[8K/16K Detection]

001

-

*ENG

[0 to 3 / 0 / 1/step]

0: Normal Detection

1: A4-Sideways LT-Lengthwise

2: LT-Sideways A4-Lengthwise

3: 8K 16K

Sets assign of decision size when original size is detected.

 When “0: JA” or “1: NA” is set at SP5-131-001, “3: 8K 16K series” can not be selected with SP4-305-001.

4308

[Scan Size Detection]

001

Detection ON/OFF

*ENG

[0 to 2 / 1 / 1/step]

0: OFF

1: ON

2: APS

Switch Original size detection ON/OFF.

4309

[Scan Size Detect:Setting]

001

Original Density Thresh

*ENG

[0 to 255 / 12 / 1digit/step]

Sets scan image density Thresh for Scan size detection.

002

Detection Time

*ENG

[20 to 100 / 60 / 20 msecstep]

Detection time for scan size detection.

003

Lamp ON:Delay Time

*ENG

[40 to 200 / 40 / 10 msec/step]

Adjusts lamp light timing for scan size detection.

004

LED PWM Duty

*ENG

[0 to 100 / 45 / 1/step]

Adjusts lamp light timing for scan size detection.

4310

[Scan Size Detect Value]

Checks the density of scanning data for the scan size detection.

001

S1:R

ENG

[0 to 255 / 0 / 1digit/step]

002

S1:G

ENG

003

S1:B

ENG

004

S2:R

ENG

005

S2:G

ENG

006

S2:B

ENG

007

S3:R

ENG

008

S3:G

ENG

009

S3:B

ENG

4350

[Intermittent Shading : BW]

001

Switch On/Off

ENG

[0 or 1 / 1 / 1/step]

0: Every time shading 1: Interval shading

Switches On/OFF for Intermittent Shading when scanning BW (Simplex/Duplex).

002

Interval 1

ENG

[0 to 65535 / 180 / 1sec/step]

Sets Intermittent Shading interval 1(from light on to the times done in Intermittent Shading interval set with SP4-350-003) when scanning BW.

003

Interval 1 Repetitions

ENG

[1 to 60 / 1 / 1/step]

Sets Shading time within Interval1 when scanning BW.

004

Interval 2

ENG

[0 to 65535 / 180 / 1sec/step]

Sets Intermittent Shading interval 2(Intermittent Shading interval after interval1 is dome) when scanning BW.

4351

[Intermittent Shading : FC]

001

Switch On/Off

ENG

[0 or 1 / 1 / 1/step]

0: Every time shading 1: Interval shading

Selects shading operation for color scanning.

002

Interval 1

ENG

[0 to 65535 / 180 / 1sec/step]

Sets interval shading interval 1 for Color scanning (Duplex/Simplex).

003

Interval 1 Repetitions

ENG

[1 to 60 / 1 / 1/step]

Sets operating times of interval shading interval 1 for color scanning (Duplex/Simplex).

004

Interval 2

ENG

[0 to 65535 / 180 / 1sec/step]

Sets interval shading interval 2 for Color scanning (Duplex/Simplex).

4400

[Org Edge Mask]

001

Book:Sub:LEdge(Left)

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase original shadow of sub scan leading edge (left side or original table) when scanning with book scanner.

002

Book:Sub:TEdge(Right)

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase original shadow of sub scan trailing edge (right side or original table) when scanning with book scanner.

003

Book:Main:LEdge(Rear)

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase original shadow of main scan leading edge (rear side or original table) when scanning with book scanner.

004

Book:Main:Tedge(Front)

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase original shadow of main scan trailing edge (front side or original table) when scanning with book scanner.

4400

[Scanner Erase Margin]

005

ADF:Sub:LEdge(Left)

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase original shadow of sub scan leading edge when scanning with ADF.

007

ADF:Main:LEdge(Rear)

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase original shadow of main scan leading edge when scanning with ADF.

008

ADF:Main:TEdge(Front)

*ENG

[0.0 to 3.0 / 0.0 / 0.1 mm/step]

Sets mask area to erase original shadow of main scan trailing edge when scanning with ADF.

4417

[IPU Test Pattern]

001

Test Pattern

ENG

[0 to 8 / 0 / 1/step]

0: Scanned image

1: Gradation main scan A 2: Patch 16C

3: Grid pattern A

4: Slant grid pattern B 5: Slant grid pattern C 6: Slant grid pattern D

7: Scanned+Slant Grid C 8: Scanned+Slant Grid D

Selects test pattern packaged with IPU ASIC.

Pattern is for design purpose, content of pattern will be omit,

4429

[Select Copy Data Security]

001

Copying

*ENG

[0 to 3 / 3 / 1/step]

Switches unjust copy output pattern density for copy. As the value enlarges, gets deeper.

002

Scanning

*ENG

[0 to 3 / 3 / 1/step]

Switches unjust copy output pattern density for scan. As the value enlarges, gets deeper.

003

Fax Operation

*ENG

[0 to 3 / 3 / 1/step]

Switches unjust copy output pattern density for fax. As the value enlarges, gets deeper.

4450

[Scan Image Pass Selection]

001

Black Subtraction ON/OFF

*ENG

[0 or 1 / 1 / 1/step] 0:OFF

1:ON(Normal)

Switches IPU Scanner image pass ON/OFF (black reduction).

Use to evaluate design, analyze cause of malfunction (image error).

002

SH ON/OFF

*ENG

[0 or 1 / 0 / 1/step]

0: ON(Normal)

1: OFF

Switches IPU Scanner image pass ON/OFF (shading).

Use to evaluate design, analyze cause of malfunction (image error).

002

SH ON/OFF

*ENG

[0 or 1 / 0 / 1/step]

0: ON(Normal)

1: OFF

Switches IPU Scanner image pass ON/OFF (shading).

Use to evaluate design, analyze cause of malfunction (image error).

002

SH ON/OFF

*ENG

[0 or 1 / 0 / 1/step]

0: ON(Normal)

1: OFF

Switches IPU Scanner image pass ON/OFF (shading).

Use to evaluate design, analyze cause of malfunction (image error).

4460

[Digital AE]

001

Low Limit Value

*ENG

[0 to 1023 / 364 / 1/step]

Sets lower limit threshold to detect background when scanning with DF front/ Book. Considers as background when an area of input image is brighter (larger value) than threshold.

002

Background level

*ENG

[512 to 1535 / 932 / 1/step]

Sets background level to decide output value of background erase when scanning DF front / Book. As the value enlarges, gets thinner.

4460

[Digital AE]

001

Low Limit Value

*ENG

[0 to 1023 / 364 / 1/step]

Sets lower limit threshold to detect background when scanning with DF front/ Book. Considers as background when an area of input image is brighter (larger value) than threshold.

002

Background level

*ENG

[512 to 1535 / 932 / 1/step]

Sets background level to decide output value of background erase when scanning DF front / Book. As the value enlarges, gets thinner.

4460

[Digital AE]

001

Low Limit Value

*ENG

[0 to 1023 / 364 / 1/step]

Sets lower limit threshold to detect background when scanning with DF front/ Book. Considers as background when an area of input image is brighter (larger value) than threshold.

002

Background level

*ENG

[512 to 1535 / 932 / 1/step]

Sets background level to decide output value of background erase when scanning DF front / Book. As the value enlarges, gets thinner.

4501

[ACC Target Den]

001

Copy:K:Text

*ENG

[0 to 10 / 5 / 1/step]

Sets target value of copy ACC against letter (edge) part Black plate.

002

Copy:C:Text

*ENG

[0 to 10 / 5 / 1/step]

Sets target value of copy ACC against letter (edge) part Cyan plate.

003

Copy:M:Text

*ENG

[0 to 10 / 5 / 1/step]

Sets target value of copy ACC against letter (edge) part Magenta plate.

004

Copy:Y:Text

*ENG

[0 to 10 / 5 / 1/step]

Sets target value of copy ACC against letter (edge) part Yellow plate.

005

Copy:K:Photo

*ENG

[0 to 10 / 5 / 1/step]

Sets target value of copy ACC against photo (non edge) part Black plate.

006

Copy:C:Photo

*ENG

[0 to 10 / 5 / 1/step]

Sets target value of copy ACC against photo (non edge) part Cyan plate.

007

Copy:M:Photo

*ENG

[0 to 10 / 5 / 1/step]

Sets target value of copy ACC against photo (non edge) part Magenta plate.

008

Copy:Y:Photo

*ENG

[0 to 10 / 5 / 1/step]

Sets target value of copy ACC against photo (non edge) part Yellow plate.

4505

[ACC Cor:Bright]

001

Master:K

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against letter (edge) part Black plate (Highlight area) depending on setting value (-128 to 127).

002

Master:C

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against letter (edge) part Cyan plate (Highlight area) depending on setting value (-128 to 127).

003

Master:M

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against letter (edge) part Magenta plate (Highlight area) depending on setting value (-128 to 127).

004

Master:Y

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against letter (edge) part Yellow plate (Highlight area) depending on setting value (-128 to 127).

005

Slave:K

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against photo (non edge) part Black plate (Highlight area) depending on setting value (-128 to 127).

006

Slave:C

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against photo (non edge) part Cyan plate (Highlight area) depending on setting value (-128 to 127).

007

Slave:M

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against photo (non edge) part Magenta plate (Highlight area) depending on setting value (-128 to 127).

008

Slave:Y

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against photo (non edge) part Yellow plate (Highlight area) depending on setting value (-128 to 127).

4506

[ACC Cor:Dark]

001

Master:K

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against letter (edge) part Black plate (Shadow area) depending on setting value (-128 to 127).

002

Master:C

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against letter (edge) part Cyan plate (Shadow area) depending on setting value (-128 to 127).

003

Master:M

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against letter (edge) part Magenta plate (Shadow area) depending on setting value (-128 to 127).

004

Master:Y

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against letter (edge) part Yellow plate (Shadow area) depending on setting value (-128 to 127).

005

Slave:K

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against photo (non edge) part Black plate (Shadow area) depending on setting value (-128 to 127).

006

Slave:C

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against photo (non edge) part Cyan plate (Shadow area) depending on setting value (-128 to 127).

007

Slave:M

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against photo (non edge) part Magenta plate (Shadow area) depending on setting value (-128 to 127).

008

Slave:Y

*ENG

[-128 to 127 / 0 / 1/step]

Adjusts target value (larger, thinner) of copy ACC against photo (non edge) part Yellow plate (Shadow area) depending on setting value (-128 to 127).

4520

[IBACC:DetectedValue]

Latest density detecting value per IBACC pattern.

001

Latest:K_P1

*ENG

[0 to 1023 / 0 / 1/step]

002

Latest:K_P2

*ENG

003

Latest:K_P3

*ENG

004

Latest:K_P4

*ENG

005

Latest:K_P5

*ENG

006

Latest:K_P6

*ENG

021

Latest:C_P1

*ENG

022

Latest:C_P2

*ENG

023

Latest:C_P3

*ENG

024

Latest:C_P4

*ENG

025

Latest:C_P5

*ENG

026

Latest:C_P6

*ENG

041

Latest:M_P1

*ENG

042

Latest:M_P2

*ENG

043

Latest:M_P3

*ENG

044

Latest:M_P4

*ENG

045

Latest:M_P5

*ENG

046

Latest:M_P6

*ENG

061

Latest:Y_P1

*ENG

062

Latest:Y_P2

*ENG

063

Latest:Y_P3

*ENG

064

Latest:Y_P4

*ENG

065

Latest:Y_P5

*ENG

066

Latest:Y_P6

*ENG

4520

[IBACC:DetectedValue]

Last density detecting value per IBACC pattern.

101

Previous:K_P1

*ENG

[0 to 1023 / 0 / 1/step]

102

Previous:K_P2

*ENG

103

Previous:K_P3

*ENG

104

Previous:K_P4

*ENG

105

Previous:K_P5

*ENG

106

Previous:K_P6

*ENG

121

Previous:C_P1

*ENG

122

Previous:C_P2

*ENG

123

Previous:C_P3

*ENG

124

Previous:C_P4

*ENG

125

Previous:C_P5

*ENG

126

Previous:C_P6

*ENG

141

Previous:M_P1

*ENG

142

Previous:M_P2

*ENG

143

Previous:M_P3

*ENG

144

Previous:M_P4

*ENG

145

Previous:M_P5

*ENG

146

Previous:M_P6

*ENG

161

Previous:Y_P1

*ENG

162

Previous:Y_P2

*ENG

163

Previous:Y_P3

*ENG

164

Previous:Y_P4

*ENG

165

Previous:Y_P5

*ENG

166

Previous:Y_P6

*ENG

4540

[Print Coverage]

001

RY Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of R (to Y) Phase.

002

RY Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding R (to Y) Phase. Larger the darker.

003

RY Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding R (to Y) Phase. Larger the darker.

004

RY Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding R (to Y) Phase. Larger the darker.

005

YR Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of Y (to R) Phase.

006

YR Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding Y (to R) Phase. Larger the darker.

007

YR Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding Y (to R) Phase. Larger the darker.

008

YR Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding Y (to R) Phase. Larger the darker.

009

YG Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of Y (to G) Phase.

010

YG Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding Y (to G) Phase. Larger the darker.

011

YG Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding Y (to G) Phase. Larger the darker.

012

YG Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding Y (to G) Phase. Larger the darker.

013

GY Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of G (to Y) Phase.

014

GY Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding G (to Y) Phase. Larger the darker.

015

GY Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding G (to Y) Phase. Larger the darker.

016

GY Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding G (to Y) Phase. Larger the darker.

017

GC Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of G (to C) Phase.

018

GC Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding G (to C) Phase. Larger the darker.

019

GC Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding G (to C) Phase. Larger the darker.

020

GC Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding G (to C) Phase. Larger the darker.

021

CG Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of C (to G) Phase.

022

CG Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding C (to G) Phase. Larger the darker.

023

CG Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding C (to G) Phase. Larger the darker.

024

CG Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding C (to G) Phase. Larger the darker.

025

CB Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of C (to B) Phase.

026

CB Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding C (to B) Phase. Larger the darker.

027

CB Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding C (to B) Phase. Larger the darker.

028

CB Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding C (to B) Phase. Larger the darker.

029

BC Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of B (to C) Phase.

030

BC Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding B (to C) Phase. Larger the darker.

031

BC Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding B (to C) Phase. Larger the darker.

032

BC Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding B (to C) Phase. Larger the darker.

033

BM Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of B (to M) Phase.

034

BM Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding B (to M) Phase. Larger the darker.

035

BM Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding B (to M) Phase. Larger the darker.

036

BM Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding B (to M) Phase. Larger the darker.

037

MB Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of M (to B) Phase.

038

MB Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding M (to B) Phase. Larger the darker.

039

MB Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding M (to B) Phase. Larger the darker.

040

MB Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding M (to B) Phase. Larger the darker.

041

MR Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of M (to R) Phase.

042

MR Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding M (to R) Phase. Larger the darker.

043

MR Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding M (to R) Phase. Larger the darker.

044

MR Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding M (to R) Phase. Larger the darker.

045

RM Phase: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of R (to M) Phase.

046

RM Phase: R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding R (to M) Phase. Larger the darker.

047

RM Phase: G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding R (to M) Phase. Larger the darker.

048

RM Phase: B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding R (to M) Phase. Larger the darker.

049

WHITE: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of highlight area.

050

WHITE:R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding highlight area. Larger the darker.

051

WHITE:G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding highlight area. Larger the darker.

052

WHITE:B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding highlight area. Larger the darker.

053

BLACK: Option

*ENG

[0 to 255 / 0 / 1/step] 0:OFF

1:ON

Sets ON/OFF (0: OFF, 1: ON) for copy output color adjust (each corresponding picture quality mode) of shadow area.

054

BLACK:R

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (C ingredient) corresponding shadow area. Larger the darker.

055

BLACK:G

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (M ingredient) corresponding shadow area. Larger the darker.

056

BLACK:B

*ENG

[-256 to 255 / 0 / 1/step]

Adjusts Value (-256 to +255) for copy output color (Y ingredient) corresponding shadow area. Larger the darker.

4550

[Scan Apli:Txt/Print]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for Scan Apli: Text/Chart mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for Scan Apli: Text/ Chart mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for Scan Apli: Text/ Chart mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for Scan Apli: Text/ Chart mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for Scan Apli: Text/ Chart mode. 0 is for OFF, Larger the value, Stronger the Erase.

4551

[Scan Apli:Txt]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for Scan Apli: Text mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for Scan Apli: Text mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for Scan Apli: Text mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for Scan Apli: Text mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for Scan Apli: Text mode. 0 is for OFF, Larger the value, Stronger the Erase.

4552

[Scan Apli:Txt Dropout]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for Scan Apli: Text (Drop Out Color) mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for Scan Apli: Text (Drop Out Color) mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for Scan Apli: Text (Drop Out Color) mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for Scan Apli: Text (Drop Out Color) mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for Scan Apli: Text (Drop Out Color) mode. 0 is for OFF, Larger the value, Stronger the Erase.

4553

[Scan Apli:Txt/Photo]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for Scan Apli: Text/Photo mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for Scan Apli: Text/Photo mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for Scan Apli: Text/Photo mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for Scan Apli: Text/Photo mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for Scan Apli: Text/Photo mode. 0 is for OFF, Larger the value, Stronger the Erase.

4554

[Scan Apli:Photo]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for Scan Apli: Photo mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for Scan Apli: Photo mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for Scan Apli: Photo mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for Scan Apli: Photo mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for Scan Apli: Photo mode. 0 is for OFF, Larger the value, Stronger the Erase.

4565

[Scan Apli:GrayScale]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for Scan Apli: GrayScale mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for Scan Apli: GrayScale mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for Scan Apli: GrayScale mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for Scan Apli: GrayScale mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for Scan Apli: GrayScale mode. 0 is for OFF, Larger the value, Stronger the Erase.

4570

[Scan Apli:Col Txt/Photo]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for Scan Apli: Color Text/Photo mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for Scan Apli: Color Text/Photo mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for Scan Apli: Color Text/Photo mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for Scan Apli: Color Text/Photo mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for Scan Apli: Color Text/Photo mode. 0 is for OFF, Larger the value, Stronger the Erase.

4571

[Scan Apli:Col Gloss Photo]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for Scan Apli: Color Gloss Photo mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for Scan Apli: Color Gloss Photo mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for Scan Apli: Color Gloss Photo mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for Scan Apli: Color Gloss Photo mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for Scan Apli: Color Gloss Photo mode. 0 is for OFF, Larger the value, Stronger the Erase.

4572

[Scan Apli:AutoCol]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for Scan Apli: Auto Color mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for Scan Apli: Auto Color mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for Scan Apli: Auto Color mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for Scan Apli: Auto Color mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for Scan Apli: Auto Color mode. 0 is for OFF, Larger the value, Stronger the Erase.

4580

[Fax Apli:Txt/Chart]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for FAX Apli: Text/Chart mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for FAX Apli: Text/Chart mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for FAX Apli: Text/Chart mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for FAX Apli: Text/Chart mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for FAX Apli: Text/Chart mode. 0 is for OFF, Larger the value, Stronger the Erase.

010

Texture Erase: 0

*ENG

[0 to 2 / 0 / 1/step]

Sets Texture Erase for FAX Apli: Text/Chart mode. 0: Fixed Threshold, 1: Variable Threshold, 2: Variable Threshold (Threshold type used for 1 and 2 are different)

4581

[Fax Apli:Txt]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for FAX Apli: Text mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for FAX Apli: Text mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for FAX Apli: Text mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for FAX Apli: Text mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for FAX Apli: Text mode. 0 is for OFF, Larger the value, Stronger the Erase.

4582

[Fax Apli:Txt/Photo]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for FAX Apli: Text/Photo mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for FAX Apli: Text/Photo mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for FAX Apli: Text/Photo mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for FAX Apli: Text/Photo mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for FAX Apli: Text/Photo mode. 0 is for OFF, Larger the value, Stronger the Erase.

010

Texture Erase: 0

*ENG

[0 to 2 / 0 / 1/step]

Sets Texture Erase for FAX Apli: Text/Photo mode. 0: Fixed Threshold, 1: Variable Threshold, 2: Variable Threshold (Threshold type used for 1 and 2 are different)

4583

[Fax Apli:Photo]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for FAX Apli: Photo mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for FAX Apli: Photo mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for FAX Apli: Photo mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for FAX Apli: Photo mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for FAX Apli: Photo mode. 0 is for OFF, Larger the value, Stronger the Erase.

010

Texture Erase: 0

*ENG

[0 to 2 / 0 / 1/step]

Sets Texture Erase for FAX Apli: Photo mode. 0: Fixed Threshold, 1: Variable Threshold, 2: Variable Threshold (Threshold type used for 1 and 2 are different)

4584

[Fax Apli:Original 1]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for FAX Apli: Special Original 1 mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for FAX Apli: Special Original 1 mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for FAX Apli: Special Original 1 mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for FAX Apli: Special Original 1 mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Ind Dot Erase: 0(Off) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for FAX Apli: Special Original 1 mode. 0 is for OFF, Larger the value, Stronger the Erase.

4585

[Fax Apli:Original 2]

005

MTF: 0(Off) 1-15

(Weak-Strong)

*ENG

[0 to 15 / 8 / 1/step]

Sets emphasis level for FAX Apli: Special Original 2 mode. 0 is for OFF, Larger the value, Stronger the emphasis.

006

Smoothing: 0(x1) 1-7 (Weak-Strong)

*ENG

[0 to 7 / 4 / 1/step]

Sets Smoothing level for FAX Apli: Special Original 2 mode. 0 is for OFF, Larger the value, the Smoother.

007

Brightness: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Brightness level (1 to 255) for FAX Apli: Special Original 2 mode. 128 is for No Correction, Larger the value, the Brighter.

008

Contrast: 1-255

*ENG

[1 to 255 / 128 / 1/step]

Sets Contrast level (1 to 255) for FAX Apli: Special Original 2 mode. 128 is for No Correction, Larger the value, Stronger the Contrast.

009

Independent Dot Erase (0)/ 1-7 (Strong)

*ENG

[0 to 7 / 0 / 1/step]

Sets Independent Dot Erase level for FAX Apli: Special Original 2 mode. 0 is for OFF, Larger the value, Stronger the Erase.

4600

[SBU Version Display]

001

SBU ID

ENG

[0x00 to 0xFF / 0 / 1/step]

In case of SBU's ID is irregular due to SBU malfunction, or wrong part is set, sets a cause flag to SP 4-647-001 and makes SC 144-00.

002

SCAT ID

ENG

[0x00 to 0xFF / 0 / 1/step]

Displays ID of SBU (SCAT).

In case of SBU's ID is irregular due to SBU malfunction, or wrong part is set, sets a cause flag to SP 4-647-001 and makes SC 144-00.

4602

[Scanner Memory Access]

Read/Writes register of ASIC: GASBU mount to SBU. Use for design evaluation/failure analysis.

001

-

ENG

[0x000000 to 0xFFFFFF /

0x000000 / -]

002

Scanner Memory Access

ENG

[0x0 to 0x000000FF / 0x000000 / -]

003

Data Set

ENG

-

4603

[Auto Adjustment Operation]

Runs SBU adjustment (light quantity adjust, SSCG correct, checking back level, adjusting white level) normally done when scanner powers on from SP.

Use for process adjust/design evaluation/error analyze.

001

HP Detection Enable

ENG

[0 or 1 / 0 / 1/step]

002

HP Detection Disable

ENG

[0 or 1 / 0 / 1/step]

4604

[FGATE Open/Close]

001

ENG

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

Used for to forcedly open/close FGATE to input scanner image data when doing scanner optical adjustment during the process.

Use for process adjust/design evaluation/error analyze.

4609

[Gray Balance Set: R]

001

Book Scan

*ENG

[-384 to 255 / -100 / 1digit/step]

Displays/Saves gray balance adjustment value (RED) of scanners face side (Book).

Adjusted value during the scanner unit Warranty process is saved.

002

DF Scan

*ENG

[-384 to 255 / -100 / 1digit/step]

Displays/Saves gray balance adjustment value (RED) of scanners face side (ADF).

Adjusted value during the scanner unit Warranty process is saved.

 Gray balance adjustment value of DF scan can be corrected with SP4-688-001/002: DF density adjust. (temperature difference correction of Book scan and DF face side scan)

4610

[Gray Balance Set: G]

001

Book Scan

*ENG

[-384 to 255 / -100 / 1digit/step]

Displays/Saves gray balance adjustment value (GREEN) of scanners face side (Book).

Adjusted value during the scanner unit Warranty process is saved.

002

DF Scan

*ENG

[-384 to 255 / -100 / 1digit/step]

Displays/Saves gray balance adjustment value (GREEN) of scanners face side (ADF).

Adjusted value during the scanner unit Warranty process is saved.

 Gray balance adjustment value of DF scan can be corrected with SP4-688-001/002: DF density adjust. (temperature difference correction of Book scan and DF face side scan)

4611

[Gray Balance Set: B]

001

Book Scan

*ENG

[-384 to 255 / -100 / 1digit/step]

Displays/Saves gray balance adjustment value (BLUE) of scanners face side (Book).

Adjusted value during the scanner unit Warranty process is saved.

002

DF Scan

*ENG

[-384 to 255 / -100 / 1digit/step]

Displays/Saves gray balance adjustment value (BLUE) of scanners face side (ADF).

Adjusted value during the scanner unit Warranty process is saved.

 Gray balance adjustment value of DF scan can be corrected with SP4-688-001/002: DF density adjust. (temperature difference correction of Book scan and DF face side scan)

4635

[SSCG Correction Set]

001

Mode Selection

*ENG

[0 to 3 / 1 / 1/step]

0: Do not noise correct SSCG.

1: Only adjust analog (initial value) 2: Only adjust digital

3: Adjust both analog/digital

Selects SSCG noise correction mode.

Use when setting SSCG adjust OFF as a temporally proceed when SSCG does not work correctly due to an unexpected malfunction.

Temporally use if by changing settings improves wide stripes, side stripes caused by scanner when SSCG correction does not work correctly.

4637

[SSCG Correction Value (Ana.)]

001

Latest:RE

ENG

[-31 to 31 / 0 / 1digit/step]

Displays SSCG analog correction value (F Side/RED/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

002

Latest:RO

ENG

[-31 to 31 / 0 / 1digit/step]

Displays SSCG analog correction value (F Side/RED/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

003

Latest:GE

ENG

[-31 to 31 / 0 / 1digit/step]

Displays SSCG analog correction value (F Side/GREEN/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

004

Latest:GO

ENG

[-31 to 31 / 0 / 1digit/step]

Displays SSCG analog correction value (F Side/GREEN/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

005

Latest:BE

ENG

[-31 to 31 / 0 / 1digit/step]

Displays SSCG analog correction value (F Side/BLUE/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

006

Latest:BO

ENG

[-31 to 31 / 0 / 1digit/step]

Displays SSCG analog correction value (F Side/BLUE/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

Displays SSCG analog correction value (F Side/BLUE/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

006

Latest:BO

ENG

[-31 to 31 / 0 / 1digit/step]

Displays SSCG analog correction value (F Side/BLUE/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

Displays SSCG analog correction value (F Side/BLUE/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

006

Latest:BO

ENG

[-31 to 31 / 0 / 1digit/step]

Displays SSCG analog correction value (F Side/BLUE/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

4638

[SSCG Correction Value (Dig.)]

001

Latest:RE

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/RED/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

002

Latest:RO

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/RED/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

003

Latest:GE

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/GREEN/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

004

Latest:GO

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/GREEN/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

005

Latest:BE

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/BLUE/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

4638

[SSCG Correction Value (Dig.)]

001

Latest:RE

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/RED/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

002

Latest:RO

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/RED/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

003

Latest:GE

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/GREEN/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

004

Latest:GO

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/GREEN/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

005

Latest:BE

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/BLUE/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

4638

[SSCG Correction Value (Dig.)]

001

Latest:RE

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/RED/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

002

Latest:RO

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/RED/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

003

Latest:GE

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/GREEN/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

004

Latest:GO

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/GREEN/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

005

Latest:BE

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/BLUE/EVEN pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

006

Latest:BO

*ENG

[-255 to 255 / 0 / 1digit/step]

Displays SSCG Digital correction value (F Side/BLUE/ODD pixel). Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

4639

[SSCG Noise Cancel (Analog)]

001

Factory Setting:RE

*ENG

[-31 to 31 / 0 / 1digit/step]

Display/Saves Factory SSCG Analog correction value (F Side/RED/EVEN pixel).

Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

002

Factory Setting:RO

*ENG

[-31 to 31 / 0 / 1digit/step]

Display/Saves Factory SSCG Analog correction value (F Side/RED/ODD pixel). Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

003

Factory Setting:GE

*ENG

[-31 to 31 / 0 / 1digit/step]

Display/Saves Factory SSCG Analog correction value (F Side/GREEN/EVEN pixel).

Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

004

Factory Setting:GO

*ENG

[-31 to 31 / 0 / 1digit/step]

Display/Saves Factory SSCG Analog correction value (F Side/GREEN/ODD pixel).

Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

005

Factory Setting:BE

*ENG

[-31 to 31 / 0 / 1digit/step]

Display/Saves Factory SSCG Analog correction value (F Side/BLUE/EVEN pixel).

Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

006

Factory Setting:BO

*ENG

[-31 to 31 / 0 / 1digit/step]

Display/Saves Factory SSCG Analog correction value (F Side/BLUE/ODD pixel).

Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

4640

[SSCG Correction Value (Dig.)]

001

Factory Setting:RE

ENG

[-255 to 255 / 0 / 1digit/step]

Display/Saves Factory SSCG Digital correction value (F Side/RED/EVEN pixel). Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

002

Factory Setting:RO

ENG

[-255 to 255 / 0 / 1digit/step]

Display/Saves Factory SSCG Digital correction value (F Side/RED/ODD pixel). Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

003

Factory Setting:GE

ENG

[-255 to 255 / 0 / 1digit/step]

Display/Saves Factory SSCG Digital correction value (F Side/GREEN/EVEN pixel).

Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

004

Factory Setting:GO

ENG

[-255 to 255 / 0 / 1digit/step]

Display/Saves Factory SSCG Digital correction value (F Side/GREEN/ODD pixel).

Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

005

Factory Setting:BE

ENG

[-255 to 255 / 0 / 1digit/step]

Display/Saves Factory SSCG Digital correction value (F Side/BLUE/EVEN pixel).

Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

006

Factory Setting:BO

ENG

[-255 to 255 / 0 / 1digit/step]

Display/Saves Factory SSCG Digital correction value (F Side/BLUE/ODD pixel). Adjusted SSCG correction Value during the main unit warranty process is saved.

Use for analyzing malfunction, comparing factory / current value.

4641

[SSCG Noise Amplitude]

001

RE

ENG

[0 to 1023 / 0 / 1digit/step]

Displays SSCG Nose Amplitude (F Side/RED/EVEN pixel) when adjusting SSCG.

Correction value will be decided depending on detected Noise Amplitude when adjusting.

Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

002

RO

ENG

[0 to 1023 / 0 / 1digit/step]

Displays SSCG Nose Amplitude (F Side/RED/ODD pixel) when adjusting SSCG.

Correction value will be decided depending on detected Noise Amplitude when adjusting.

Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

003

GE

ENG

[0 to 1023 / 0 / 1digit/step]

Displays SSCG Nose Amplitude (F Side/GREEN/EVEN pixel) when adjusting SSCG.

Correction value will be decided depending on detected Noise Amplitude when adjusting.

Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

004

GO

ENG

[0 to 1023 / 0 / 1digit/step]

Displays SSCG Nose Amplitude (F Side/GREEN/ODD pixel) when adjusting SSCG.

Correction value will be decided depending on detected Noise Amplitude when adjusting.

Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

005

BE

ENG

[0 to 1023 / 0 / 1digit/step]

Displays SSCG Nose Amplitude (F Side/BLUE/EVEN pixel) when adjusting SSCG.

Correction value will be decided depending on detected Noise Amplitude when adjusting.

Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

006

BO

ENG

[0 to 1023 / 0 / 1digit/step]

Displays SSCG Nose Amplitude (F Side/BLUE/ODD pixel) when adjusting SSCG.

Correction value will be decided depending on detected Noise Amplitude when adjusting.

Adjustment will be done when scanner turns on.

Use for design evaluation, analyzing malfunction (abnormal images).

4646

[Scan Adjust Error]

Displays error value of scanning adjustment.

001

White level

ENG

[0 to 65535 / 0 / 1/step] Bit15:Unused

Bit14: Unused

Bit13:White level abnormal (F side/RED/EVEN pixel)

Bit12: White level abnormal (F side

/RED/ODD pixel)

Bit11: White level abnormal (F side

/GREEN/EVEN pixel)

Bit10: White level abnormal (F side

/GREEN/ODD pixel)

Bit9: White level abnormal (F side

/BLUE/EVEN pixel)

Bit8:White level abnormal (F side

/BLUE/ODD pixel) Bit7: Unused

Bit6: Unused

Bit5:gain abnormal (F side

/RED/EVEN pixel)

Bit4: gain abnormal (F side

/RED/ODD pixel)

Bit3: gain abnormal (F side

/GREEN/EVEN pixel)

Bit2: gain abnormal (F side

/GREEN/ODD pixel)

Bit1: gain abnormal (F side

/BLUE/EVEN pixel)

Bit0: gain abnormal (F side

/BLUE/ODD pixel)

Shows cause of error when an error occurs during the white level adjustment when scanner turns on.

When an error, SC142-00(F side/white level adjustment error)will be given.[format] binary

Scan adjust error (F side/White level) flag= (b15,b14,b13,b12,b11,b10,b9,b8,b7,b6,b5,b4,b3,b2,b1,b0)

002

Black level

ENG

[0 to 65535 / 0 / 1/step] Bit7: Unused

Bit6: Unused

Bit5: Black level abnormal (F side/RED/EVEN Pixel)

Bit4: Black level abnormal (F side

/RED/ODD Pixel)

Bit3: Black level abnormal (F side

/GREEN/EVEN Pixel)

Bit2: Black level abnormal (F side

/GREEN/ODD Pixel)

Bit1: Black level abnormal (F side

/BLUE/EVEN Pixel)

Bit0: Black level abnormal (F side

/BLUE/ODD Pixel)

Shows cause of error when an error occurs With the Black level check when scanner turns on.

When an error, SC141-00(F side/Black level adjustment error) will be given. [format] binary

Scan adjust error (F side/Black level) flag=(b7,b6,b5,b4,b3,b2,b1,b0)

003

SSCG Correction

ENG

[0 to 65535 / 0 / 1/step] Bit7: Unused

Bit6: Unused

Bit5: SSCG correction error (Fside/RED/EVEN Pixel) Bit4: SSCG correction error (Fside/RED/ODD Pixel) Bit3: SSCG correction error (Fside/GREEN/EVEN Pixel) Bit2: SSCG correction error (Fside/GREEN/ODD Pixel) Bit1: SSCG correction error (Fside/BLUE/EVEN Pixel) Bit0: SSCG correction error (Fside/BLUE/ODD Pixel)

Shows cause of error when an error occurs With the SSCG Noise correction when scanner turns on.

When an error, Correction turns off. [format] binary

Scan adjust error (F side/SSCG correction) flag= (b7,b6,b5,b4,b3,b2,b1,b0)

4647

[Scanner Hard Error]

Displays result of SBU connection check.

001

Power-ON

ENG

[0 to 65535 / 0 / 1/step] Bit15: Unused

Bit14:SBU hardware error (Power ON/un-reset error)

Bit13:SBU hardware error (Serial communication error: F side) Bit12:SBU hardware error (Reset error: F side)

Bit11: Unused Bit10: Unused

Bit9:SBU hardware error (Version error)

Bit8: Unused Bit7: Unused Bit6: Unused

Bit5:SBU hardware error (Serial communication error: L side) Bit4:SBU hardware error (Reset error:Lside)

Bit3: Unused Bit2: Unused Bit1: Unused

Shows cause of error when an error occurs with the SBU connection detect when Scanner turns on..

When an error, SC144-00 (SBU Communication error) will be given. [format] binary

Scan adjust error (SSCG correction) flag= (b15,b14,b13,b12,b11,b10,b9,b8,b7,b6,b5,b4,b3,b2,b1,b0)

4651

[Black Level Adj. Value (Ana.)]

001

Latest: RE Color

ENG

[0 to 127 / 0 / 1digit/step]

Displays black level analog adjustment value (RED/EVEN pixel).

Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU. Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Latest: RO Color

ENG

[0 to 127 / 0 / 1digit/step]

Displays black level analog adjustment value (RED/ODD pixel).

Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU. Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4652

[Black Level Adj. Value (Ana.)]

001

Latest: GE Color

ENG

[0 to 127 / 0 / 1digit/step]

Displays black level analog adjustment value (GREEN/EVEN pixel). Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU.

Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Latest: GO Color

ENG

[0 to 127 / 0 / 1digit/step]

Displays black level analog adjustment value (GREEN/ODD pixel). Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU.

Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4653

[Black Level Adj. Value (Ana.)]

001

Latest: BE Color

ENG

[0 to 127 / 0 / 1digit/step]

Displays black level analog adjustment value (BLUE/EVEN pixel). Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU.

Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Latest: BO Color

ENG

[0 to 127 / 0 / 1digit/step]

Displays black level analog adjustment value (BLUE/ODD pixel).

Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU. Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4654

[Black Level Adj. Value (Dig.)]

001

Latest: RE Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays black level digital adjustment value (RED/EVEN pixel).

Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU. Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Latest: RO Color

*ENG

0 to 16383 / 0 / 1digit/step]

Displays black level digital adjustment value (RED/ODD pixel).

Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU. Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4655

[Black Level Adj. Value (Dig.)]

001

Latest: GE Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays black level digital adjustment value (GREEN/EVEN pixel). Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU. Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Latest: GO Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays black level digital adjustment value (GREEN/ODD pixel). Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU.

Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4656

[Black Level Adj. Value (Dig.)]

001

Latest: BE Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays black level digital adjustment value (BLUE/EVEN pixel).

Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU. Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Latest: BO Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays black level digital adjustment value (BLUE/ODD pixel).

Black level adjust is regularly done hardwarely by ASIC (SCAT) of SBU. Adjusted value will be given from checking the black level when scanner powers ON.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4658

[Analog Gain Adjust]

001

Latest: R Color

*ENG

[0 to 14 / 0 / 1digit/step]

Displays analog gain adjustment value (RED pixel).

White level adjust is done when scanner powers ON to keep the dynamic range of image signal.

Image signal will be amplified or attenuated with white level adjust, therefore gain adjust will be done by ASIC (SCAT) of SBU hardwarely, and adjusted value will be given.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4659

[Analog Gain Adjust]

001

Latest: G Color

*ENG

[0 to 14 / 0 / 1digit/step]

Displays analog gain adjustment value (GREEN pixel).

White level adjust is done when scanner powers ON to keep the dynamic range of image signal.

Image signal will be amplified or attenuated with white level adjust, therefore gain adjust will be done by ASIC (SCAT) of SBU hardwarely, and adjusted value will be given.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4660

[Analog Gain Adjust]

001

Latest: B Color

*ENG

[0 to 14 / 0 / 1digit/step]

Displays analog gain adjustment value (BLUE pixel).

White level adjust is done when scanner powers ON to keep the dynamic range of image signal.

Image signal will be amplified or attenuated with white level adjust, therefore gain adjust will be done by ASIC (SCAT) of SBU hardwarely, and adjusted value will be given.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4661

[Digital Gain Adjust]

001

Latest: RE Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays digital gain adjustment value (RED/EVEN pixel).

White level adjust is done when scanner powers ON to keep the dynamic range of image signal.

Image signal will be amplified or attenuated with white level adjust, therefore gain adjust will be done by ASIC (SCAT) of SBU hardwarely, and adjusted value will be given.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Latest: RO Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays digital gain adjustment value (RED/ODD pixel).

White level adjust is done when scanner powers ON to keep the dynamic range of image signal.

Image signal will be amplified or attenuated with white level adjust, therefore gain adjust will be done by ASIC (SCAT) of SBU hardwarely, and adjusted value will be given.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4662

[Digital Gain Adjust]

001

Latest: GE Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays digital gain adjustment value (GREEN/EVEN pixel).

White level adjust is done when scanner powers ON to keep the dynamic range of image signal.

Image signal will be amplified or attenuated with white level adjust, therefore gain adjust will be done by ASIC (SCAT) of SBU hardwarely, and adjusted value will be given.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Latest: GO Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays digital gain adjustment value (GREEN/ODD pixel).

White level adjust is done when scanner powers ON to keep the dynamic range of image signal.

Image signal will be amplified or attenuated with white level adjust, therefore gain adjust will be done by ASIC (SCAT) of SBU hardwarely, and adjusted value will be given.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4663

[Digital Gain Adjust]

001

Latest: BE Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays digital gain adjustment value (BLUE/EVEN pixel).

White level adjust is done when scanner powers ON to keep the dynamic range of image signal.

Image signal will be amplified or attenuated with white level adjust, therefore gain adjust will be done by ASIC (SCAT) of SBU hardwarely, and adjusted value will be given.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Latest: BO Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays digital gain adjustment value (BLUE/ODD pixel).

White level adjust is done when scanner powers ON to keep the dynamic range of image signal.

Image signal will be amplified or attenuated with white level adjust, therefore gain adjust will be done by ASIC (SCAT) of SBU hardwarely, and adjusted value will be given.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4670

[Black Level Adj. Value (Ana.)]

001

Factory Setting: RE Color

*ENG

[0 to 127 / 0 / 1digit/step]

Displays/Saves factory default black level analog adjust value (RED/EVEN pixel).

Factory default black level analog adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Factory Setting: RO Color

*ENG

[0 to 127 / 0 / 1digit/step]

Displays/Saves factory default black level analog adjust value (RED/ODD pixel). Factory default black level analog adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4671

[Black Level Adj. Value (Ana.)]

001

Factory Setting: GE Color

*ENG

[0 to 127 / 0 / 1digit/step]

Displays/Saves factory default black level analog adjust value (GREEN/EVEN pixel).

Factory default black level analog adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Factory Setting: GO Color

*ENG

[0 to 127 / 0 / 1digit/step]

Displays/Saves factory default black level analog adjust value (GREEN/ODD pixel).

Factory default black level analog adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4672

[Black Level Adj. Value (Ana.)]

001

Factory Setting: BE Color

*ENG

[0 to 127 / 0 / 1digit/step]

Displays/Saves factory default black level analog adjust value (BLUE/EVEN pixel).

Factory default black level analog adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Factory Setting: BO Color

*ENG

[0 to 127 / 0 / 1digit/step]

Displays/Saves factory default black level analog adjust value (BLUE/ODD pixel).

Factory default black level analog adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4673

[Black Level Adj. Value (Dig.)]

001

Factory Setting: RE Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays/Saves factory default black level digital adjust value (RED/EVEN pixel).

Factory default black level digital adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Factory Setting: RO Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays/Saves factory default black level digital adjust value (RED/ODD pixel). Factory default black level digital adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4674

[Black Level Adj. Value (Dig.)]

001

Factory Setting: GE Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays/Saves factory default black level digital adjust value (GREEN/EVEN pixel).

Factory default black level digital adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Factory Setting: GO Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays/Saves factory default black level digital adjust value (GREEN/ODD pixel).

Factory default black level digital adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4675

[Black Level Adj. Value (Dig.)]

001

Factory Setting: BE Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays/Saves factory default black level digital adjust value (BLUE/EVEN pixel).

Factory default black level digital adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Factory Setting: BO Color

*ENG

[0 to 16383 / 0 / 1digit/step]

Displays/Saves factory default black level digital adjust value (BLUE/ODD pixel).

Factory default black level digital adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4677

[Analog Gain Adjust]

001

Factory Setting: R Color

*ENG

[0 to 14 / 0 / 1digit/step]

Displays/Saves factory default analog gain adjust value (RED pixel). Factory default analog gain adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4678

[Analog Gain Adjust]

001

Factory Setting: G Color

*ENG

[0 to 14 / 0 / 1digit/step]

Displays/Saves factory default analog gain adjust value (GREEN pixel). Factory default analog gain adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4679

[Analog Gain Adjust]

001

Factory Setting: B Color

*ENG

[0 to 14 / 0 / 1digit/step]

Displays/Saves factory default analog gain adjust value (BLUE pixel). Factory default analog gain adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4680

[Digital Gain Adjust]

001

Factory Setting: RE Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays/Saves factory default digital gain adjust value (RED/EVEN pixel). Factory default analog gain adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Factory Setting: RO Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays/Saves factory default digital gain adjust value (RED/ODD pixel). Factory default analog gain adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4681

[Digital Gain Adjust]

001

Factory Setting: GE Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays/Saves factory default digital gain adjust value (GREEN/EVEN pixel). Factory default analog gain adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Factory Setting: GO Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays/Saves factory default digital gain adjust value (GREEN/ODD pixel). Factory default analog gain adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4682

[Digital Gain Adjust]

001

Factory Setting: BE Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays/Saves factory default digital gain adjust value (BLUE/EVEN pixel). Factory default analog gain adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

Factory Setting: BO Color

*ENG

[0 to 1023 / 0 / 1digit/step]

Displays/Saves factory default digital gain adjust value (BLUE/ODD pixel). Factory default analog gain adjustment value is saved during the main unit warranty process.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4688

[DF Density Adjustment]

001

ARDF

*ENG

[80 to 120 / 102 / 1 %/step] Value increase: ADF density deeper.

Value decrease: ADF density thinner.

For Oversetters only. Adjusts density difference between Book and ADF.

4688

[Scan Image Density Adjustment]

002

1-pass DF

*ENG

[80 to 120 / 103 / 1 %/step]

For Single-Pass simultaneous duplex models only. Adjusts density difference between Book and ADF.

4690

[White Level Peak Read]

001

RE

ENG

[0 to 1023 / 0 / 1digit/step]

Displays white level peak scanning value (RED/EVEN pixel).

White level adjust is done by scanning the white reference plate when scanner powers ON to keep the dynamic range of image signal.

Scanning level of white reference plate from white level adjusting is given. When white level peak scanning value is an error (adjustment not finishing correctly) SC142-00 is given.

Cause of error will be displayed on SP4-646-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

RO

ENG

[0 to 1023 / 0 / 1digit/step]

Displays white level peak scanning value (RED/ODD pixel).

White level adjust is done by scanning the white reference plate when scanner powers ON to keep the dynamic range of image signal.

Scanning level of white reference plate from white level adjusting is given. When white level peak scanning value is an error (adjustment not finishing correctly) SC142-00 is given.

Cause of error will be displayed on SP4-646-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4691

[White Level Peak Read]

001

GE

ENG

[0 to 1023 / 0 / 1digit/step]

Displays white level peak scanning value (GREEN/EVEN pixel).

White level adjust is done by scanning the white reference plate when scanner powers ON to keep the dynamic range of image signal.

Scanning level of white reference plate from white level adjusting is given. When white level peak scanning value is an error (adjustment not finishing correctly) SC142-00 is given.

Cause of error will be displayed on SP4-646-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

GO

ENG

[0 to 1023 / 0 / 1digit/step]

Displays white level peak scanning value (GREEN/ODD pixel).

White level adjust is done by scanning the white reference plate when scanner powers ON to keep the dynamic range of image signal.

Scanning level of white reference plate from white level adjusting is given. When white level peak scanning value is an error (adjustment not finishing correctly) SC142-00 is given.

Cause of error will be displayed on SP4-646-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4692

[White Level Peak Read]

001

BE

ENG

[0 to 1023 / 0 / 1digit/step]

Displays white level peak scanning value (BLUE/EVEN pixel).

White level adjust is done by scanning the white reference plate when scanner powers ON to keep the dynamic range of image signal.

Scanning level of white reference plate from white level adjusting is given. When white level peak scanning value is an error (adjustment not finishing correctly) SC142-00 is given.

Cause of error will be displayed on SP4-646-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

BO

ENG

[0 to 1023 / 0 / 1digit/step]

Displays white level peak scanning value (BLUE/ODD pixel).

White level adjust is done by scanning the white reference plate when scanner powers ON to keep the dynamic range of image signal.

Scanning level of white reference plate from white level adjusting is given. When white level peak scanning value is an error (adjustment not finishing correctly) SC142-00 is given.

Cause of error will be displayed on SP4-646-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4693

[Black Level Peak Read]

001

RE

ENG

[0 to 1023 / 0 / 1digit/step]

Displays black level scanning value (RED/EVEN pixel).

Black level check is done when scanner powers ON, then offset level of image signal is checked and that value will be given.

Check whether the offset adjustment of SBU (SCAT) is working correctly. Gives SC141-00 if the black level scanning value is an error.

Cause of error will be displayed on SP4-646-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

RO

ENG

[0 to 1023 / 0 / 1digit/step]

Displays black level scanning value (RED/ODD pixel).

Black level check is done when scanner powers ON, then offset level of image signal is checked and that value will be given.

Check whether the offset adjustment of SBU (SCAT) is working correctly. Gives SC141-00 if the black level scanning value is an error.

Cause of error will be displayed on SP4-646-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4694

[Black Level Peak Read]

-

001

GE

ENG

[0 to 1023 / 0 / 1digit/step]

Displays black level scanning value (GREEN/EVEN pixel).

Black level check is done when scanner powers ON, then offset level of image signal is checked and that value will be given.

Check whether the offset adjustment of SBU (SCAT) is working correctly. Gives SC141-00 if the black level scanning value is an error.

Cause of error will be displayed on SP4-646-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

GO

ENG

[0 to 1023 / 0 / 1digit/step]

Displays black level scanning value (GREEN/EVEN pixel).

Black level check is done when scanner powers ON, then offset level of image signal is checked and that value will be given.

Check whether the offset adjustment of SBU (SCAT) is working correctly. Gives SC141-00 if the black level scanning value is an error.

Cause of error will be displayed on SP4-646-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4695

[Black Level Peak Read]

-

001

BE

ENG

[0 to 1023 / 0 / 1digit/step]

Displays black level scanning value (BLUE/EVEN pixel).

Black level check is done when scanner powers ON, then offset level of image signal is checked and that value will be given.

Check whether the offset adjustment of SBU (SCAT) is working correctly. Gives SC141-00 if the black level scanning value is an error.

Cause of error will be displayed on SP4-646-002.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

002

BO

ENG

[0 to 1023 / 0 / 1digit/step]

Displays black level scanning value (BLUE/ODD pixel).

Black level check is done when scanner powers ON, then offset level of image signal is checked and that value will be given.

Check whether the offset adjustment of SBU (SCAT) is working correctly. Gives SC141-00 if the black level scanning value is an error.

Cause of error will be displayed on SP4-646-002.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

4698

[Factory Setting Input]

-

001

On/Off

*ENG

[0 to 1 / 0 / 1/step]

4698

[Factory Setting Input]

-

001

On/Off

*ENG

[0 to 1 / 0 / 1/step]

4698

[Factory Setting Input]

-

001

On/Off

*ENG

[0 to 1 / 0 / 1/step]

4795

[CIS Black Level Data: B]

-

Displays black level; data of CIS.

When DF powers ON, black level of CIS is checked, then detect the black level per chip and display scanning level.

Cause of error will be displayed on SP4-745-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

001

Chip1

ENG

[0 to 255 / 0 / 1digit/step]

002

Chip2

ENG

[0 to 255 / 0 / 1digit/step]

003

Chip3

ENG

[0 to 255 / 0 / 1digit/step]

004

Chip4

ENG

[0 to 255 / 0 / 1digit/step]

005

Chip5

ENG

[0 to 255 / 0 / 1digit/step]

006

Chip6

ENG

[0 to 255 / 0 / 1digit/step]

007

Chip7

ENG

[0 to 255 / 0 / 1digit/step]

008

Chip8

ENG

[0 to 255 / 0 / 1digit/step]

009

Chip9

ENG

[0 to 255 / 0 / 1digit/step]

010

Chip10

ENG

[0 to 255 / 0 / 1digit/step]

011

Chip11

ENG

[0 to 255 / 0 / 1digit/step]

012

Chip12

ENG

[0 to 255 / 0 / 1digit/step]

013

Chip13

ENG

[0 to 255 / 0 / 1digit/step]

014

Chip14

ENG

[0 to 255 / 0 / 1digit/step]

015

Chip15

ENG

[0 to 255 / 0 / 1digit/step]

4795

[CIS Black Level Data: B]

-

Displays black level; data of CIS.

When DF powers ON, black level of CIS is checked, then detect the black level per chip and display scanning level.

Cause of error will be displayed on SP4-745-001.

Use for design evaluation/analyzing cause of malfunction (abnormal image, SC).

001

Chip1

ENG

[0 to 255 / 0 / 1digit/step]

002

Chip2

ENG

[0 to 255 / 0 / 1digit/step]

003

Chip3

ENG

[0 to 255 / 0 / 1digit/step]

004

Chip4

ENG

[0 to 255 / 0 / 1digit/step]

005

Chip5

ENG

[0 to 255 / 0 / 1digit/step]

006

Chip6

ENG

[0 to 255 / 0 / 1digit/step]

007

Chip7

ENG

[0 to 255 / 0 / 1digit/step]