MAIN SP TABLES-2-1 Savin MP C3003, Ricoh MP C3003 Service Manual

HOME PAGE | < Previous | Contents | Next >

2.3 MAIN SP TABLES-2-1

2.3.1 SP2-005 TO 2-473 (DRUM)

2005	[Charge DC Voltage: Fixed]
	DC fixed voltage when Process control is off.
001	Standard Speed: K	*ENG	[0 to 2000 / 650 / 10-V/step]
002	Standard Speed: C	*ENG	[0 to 2000 / D146: 1300, D147:
003	Standard Speed: M	*ENG
			1300, D148: 650, D149: 650, D150:
			650 / 10-V/step]
004	Standard Speed: Y	*ENG
005	Middle Speed: K	*ENG	[0 to 2000 / 650 / 10-V/step]
006	Middle Speed: C	*ENG	[0 to 2000 / D146: 1300, D147:
007	Middle Speed: M	*ENG
			1300, D148: 650, D149: 650, D150:
			650 / 10-V/step]
008	Middle Speed: Y	*ENG
009	Low Speed: K	*ENG	[0 to 2000 / 650 / 10-V/step]
010	Low Speed: C	*ENG	[0 to 2000 / D146: 1300, D147:
011	Low Speed: M	*ENG
			1300, D148: 650, D149: 650, D150:
			650 / 10-V/step]
012	Low Speed: Y	*ENG
2005	[Charge DC Voltage: Correction]
	Correction amount for AC center value.
013	PCU: Standard Speed	*ENG	[-100 to 100 / 0 / 1-V/step]
014	PCU: Middle Speed	*ENG
015	PCU: Low Speed	*ENG
2005	[Charge DC Voltage: Correction]
	Vc calculating coefficient of DC Electrify.
018	Correction Coefficient a: K	*ENG	[0.000 to 2.000 / 1.000 / 0.001/step]

SP Mode Tables

Main SP Tables-2-1

019	Correction Coefficient a: C	*ENG
020	Correction Coefficient a: M	*ENG
021	Correction Coefficient a: Y	*ENG
022	Correction Coefficient b: K	*ENG	[0 to 2000 / 0 / 1/step]
023	Correction Coefficient b: C	*ENG	[0 to 2000 / D146: 20, D147: 20, D148: 0, D149: 0, D150: 0 / 1/step]
024	Correction Coefficient b: M	*ENG
025	Correction Coefficient b: Y	*ENG
026	Correction Coefficient c: K	*ENG	[0 to 100 / D146: 10, D147: 10, D148: 0, D149: 0, D150: 0 / 1/step]
027	Correction Coefficient c: C	*ENG
028	Correction Coefficient c: M	*ENG
029	Correction Coefficient c: Y	*ENG
2005	[Charge DC Voltage: Correction]
2005	Temperature threshold of Electrify DC Voltage.
030	Temperature Threshold L: K	*ENG	[0 to 99 / 15 / 1deg/step]
031	Temperature Threshold L: C	*ENG	[0 to 99 / 15 / 1deg/step]
032	Temperature Threshold L: M	*ENG	[0 to 99 / 16 / 1deg/step]
033	Temperature Threshold L: Y	*ENG	[0 to 99 / 16 / 1deg/step]
034	Temperature Threshold M: K	*ENG	[0 to 99 / 22 / 1deg/step]
035	Temperature Threshold M: C	*ENG	[0 to 99 / 22 / 1deg/step]
036	Temperature Threshold M: M	*ENG	[0 to 99 / 23 / 1deg/step]
037	Temperature Threshold M: Y	*ENG	[0 to 99 / 23 / 1deg/step]
038	Temperature Threshold H: K	*ENG	[0 to 99 / 28 / 1deg/step]
039	Temperature Threshold H: C	*ENG	[0 to 99 / 28 / 1deg/step]
040	Temperature Threshold H: M	*ENG	[0 to 99 / 29 / 1deg/step]
041	Temperature Threshold H: Y	*ENG	[0 to 99 / 29 / 1deg/step]
2005	[Charge DC Voltage: Correction]

Main SP Tables-2-1

0: Set to correction value using table.

1: Set to Fixed Value: Electrify DC Voltage of SP.

043

DC Bias Fixed Value Set

*ENG

[0 or 1 / 0 / 1/step]

2005

[Charge DC Voltage: Correction]

Fixed value of Vc calculating coefficient for DC Electrify.

044

Correction Coefficient a: Fixed K

*ENG

[0.000 to 2.000 / 1.000 / 0.001/step]

045

Correction Coefficient a: Fixed C

*ENG

046

Correction Coefficient a: Fixed M

*ENG

047

Correction Coefficient a: Fixed Y

*ENG

048

Correction Coefficient b: Fixed K

*ENG

[0 to 2000 / 0 / 1/step]

049

Correction Coefficient b: Fixed C

*ENG

[0 to 2000 / D146: 20, D147: 20,

D148: 0, D149: 0, D150: 0 / 1/step]

050

Correction Coefficient b: Fixed M

*ENG

051

Correction Coefficient b: Fixed Y

*ENG

052

Correction Coefficient c: Fixed K

*ENG

[0 to 100 / 0 / 1/step]

053

Correction Coefficient c: Fixed C

*ENG

[0 to 100 / D146: 10, D147: 10,

D148: 0, D149: 0, D150: 0 / 1/step]

054

Correction Coefficient c: Fixed M

*ENG

055

Correction Coefficient c: Fixed Y

*ENG

2005

[Charge DC Voltage: Correction]

SP Mode Tables

Main SP Tables-2-1

	Rotation distance considering by PCU life.
056	Rotation: PCU: Bk	*ENG	[0 to 999999999 / 0 / 1mm/step]
057	Rotation: PCU: C	*ENG
058	Rotation: PCU: M	*ENG
059	Rotation: PCU: Y	*ENG
2005	[Charge DC: Correction]
2005	Rotation distance when detecting an old PCU.
060	Old PCU Detection Distance: PCU: K	*ENG	[0 to 999999999 / 0 / 1mm/step]
061	Old PCU Detection Distance: PCU: C	*ENG
062	Old PCU Detection Distance: PCU: M	*ENG
063	Old PCU Detection Distance: PCU: Y	*ENG
2005	[Charge DC Voltage: Correction]
2005	Vc calculating coefficient of DC Electrify.
089	Correction Coefficient Cd	*ENG	[-125 to 125 / 0 / 1-V/step]
090	Correction Coefficient Ce	*ENG
091	Correction Coefficient Cf	*ENG
092	Correction Coefficient Cg	*ENG
093	Correction Coefficient Ch	*ENG
094	Correction Coefficient Ci	*ENG
095	Correction Coefficient Cj	*ENG
096	Correction Coefficient Ck	*ENG
097	Correction Coefficient Cl	*ENG
098	Correction Coefficient Cm	*ENG

Main SP Tables-2-1

099	Correction Coefficient Cn	*ENG
100	Correction Coefficient Co	*ENG
101	Correction Coefficient Cp	*ENG
102	Correction Coefficient Cq	*ENG
103	Correction Coefficient Cr	*ENG	[-125 to 125 / 0 / 1-V/step]
104	Correction Coefficient Cs	*ENG
105	Correction Coefficient Ct	*ENG
106	Correction Coefficient Cu	*ENG
107	Correction Coefficient Cv	*ENG
108	Correction Coefficient Cw	*ENG
109	Correction Coefficient Cx	*ENG
110	Correction Coefficient Cy	*ENG	[-125 to 125 / 0 / 1-V/step]
111	Correction Coefficient Cz	*ENG
112	Correction Coefficient CAA	*ENG
113	Correction Coefficient CAB	*ENG
114	Correction Coefficient Md	*ENG
115	Correction Coefficient Me	*ENG
116	Correction Coefficient Mf	*ENG
117	Correction Coefficient Mg	*ENG	[-125 to 125 / 0 / 1-V/step]
118	Correction Coefficient Mh	*ENG
119	Correction Coefficient Mi	*ENG
120	Correction Coefficient Mj	*ENG
121	Correction Coefficient Mk	*ENG
122	Correction Coefficient Ml	*ENG
123	Correction Coefficient Mm	*ENG
124	Correction Coefficient Mn	*ENG	[-125 to 125 / 0 / 1-V/step]

SP Mode Tables

Main SP Tables-2-1

125	Correction Coefficient Mo	*ENG
126	Correction Coefficient Mp	*ENG
127	Correction Coefficient Mq	*ENG
128	Correction Coefficient Mr	*ENG
129	Correction Coefficient Ms	*ENG
130	Correction Coefficient Mt	*ENG
131	Correction Coefficient Mu	*ENG	[-125 to 125 / 0 / 1-V/step]
132	Correction Coefficient Mv	*ENG
133	Correction Coefficient Mw	*ENG
134	Correction Coefficient Mx	*ENG
135	Correction Coefficient My	*ENG
136	Correction Coefficient Mz	*ENG
137	Correction Coefficient MAA	*ENG
138	Correction Coefficient MAB	*ENG	[-125 to 125 / 0 / 1-V/step]
139	Correction Coefficient Yd	*ENG
140	Correction Coefficient Ye	*ENG
141	Correction Coefficient Yf	*ENG
142	Correction Coefficient Yg	*ENG
143	Correction Coefficient Yh	*ENG
144	Correction Coefficient Yi	*ENG
145	Correction Coefficient Yj	*ENG
146	Correction Coefficient Yk	*ENG
147	Correction Coefficient Yl	*ENG
148	Correction Coefficient Ym	*ENG
149	Correction Coefficient Yn	*ENG
150	Correction Coefficient Yo	*ENG

Main SP Tables-2-1

151	Correction Coefficient Yp	*ENG	[-125 to 125 / 0 / 1-V/step]
152	Correction Coefficient Yq	*ENG
153	Correction Coefficient Yr	*ENG
154	Correction Coefficient Ys	*ENG
155	Correction Coefficient Yt	*ENG
156	Correction Coefficient Yu	*ENG
157	Correction Coefficient Yv	*ENG
158	Correction Coefficient Yw	*ENG
159	Correction Coefficient Yx	*ENG
160	Correction Coefficient Yy	*ENG
161	Correction Coefficient Yz	*ENG
162	Correction Coefficient YAA	*ENG
163	Correction Coefficient YAB	*ENG

2006	[Charge AC Voltage: Fixed]
2006	AC ampere target value when outputting fixed Electrify AC.
001	Standard Speed: K	*ENG	[0.00 to 3.00 / 2.20 / 0.01kV/step]
002	Standard Speed: C	*ENG
003	Standard Speed: M	*ENG
004	Standard Speed: Y	*ENG
005	Middle Speed: K	*ENG
006	Middle Speed: C	*ENG
007	Middle Speed: M	*ENG
008	Middle Speed: Y	*ENG
009	Low Speed: K	*ENG
010	Low Speed: C	*ENG

SP Mode Tables

Main SP Tables-2-1

011	Low Speed: M	*ENG
012	Low Speed: Y	*ENG

2007	[Charge AC Current: LL]
2007	AC ampere target value when Electrify AC.
001	Environmental Target: Bk	*ENG	[0.00 to 3.00 / D146: 0.88, D147: 0.88, D148: 1.19, D149: 1.65, D150: 1.65 / 0.01mA/step]
002	Environmental Target: C	*ENG
003	Environmental Target: M	*ENG
004	Environmental Target: Y	*ENG

2008	[Charge AC Current: ML]
2008	AC ampere target value when Electrify AC.
001	Environmental Target: Bk	*ENG	[0.00 to 3.00 / D146: 0.89, D147: 0.89, D148: 1.18, D149: 1.64, D150: 1.64 / 0.01mA/step]
002	Environmental Target: C	*ENG
003	Environmental Target: M	*ENG
004	Environmental Target: Y	*ENG

2009	[Charge AC Current: MM]
2009	AC ampere target value when Electrify AC.
001	Environmental Target: Bk	*ENG	[0.00 to 3.00 / D146: 0.90, D147: 0.90, D148: 1.16, D149: 1.62, D150: 1.62 / 0.01mA/step]
002	Environmental Target: C	*ENG
003	Environmental Target: M	*ENG
004	Environmental Target: Y	*ENG

2010

[Charge AC Current: MH]

AC ampere target value when Electrify AC.

001

Environmental Target: Bk

*ENG

[0.00 to 3.00 / D146: 0.91, D147:

Main SP Tables-2-1

002

Environmental Target: C

*ENG

0.91, D148: 1.23, D149: 1.68,

D150: 1.68 / 0.01mA/step]

003

Environmental Target: M

*ENG

004

Environmental Target: Y

*ENG

2011	[Charge AC Current: HH]
2011	AC ampere target value when Electrify AC.
001	Environmental Target: Bk	*ENG	[0.00 to 3.00 / D146: 0.92, D147: 0.92, D148: 1.30, D149: 1.73, D150: 1.73 / 0.01mA/step]
002	Environmental Target: C	*ENG
003	Environmental Target: M	*ENG
004	Environmental Target: Y	*ENG

2012

[Charge Output Control]

001

AC Voltage

*ENG

[0 or 1 / 0 / 1/step]

0: Set to environment correction value used when FB . 1: Electrify AC voltage of SP: Set to fixed setting value.

2013	[Environmental Correction: PCU]
001	Current Environmental FC : Display	*ENG	[0 to 0 / 0 / 1/step]
	Environment class divided based on the temperature / humidity sensor information when controlling Electrify AC of latest main & subs FC mode.
002	Forced Setting	*ENG	[0 to 5 / 0 / 1/step]
	0: Detect with temperature / humidity sensor. 1 to 5: Force setting environment.
003	Absolute Humidity: Threshold 1	*ENG	[0.00 to 100.00 / 3.00 / 0.01g/m^3/step]
	Threshold of LL environment and ML environment.

SP Mode Tables

Main SP Tables-2-1

004	Absolute Humidity: Threshold 2	*ENG	[0.00 to 100.00 / 8.00 / 0.01g/m^3/step]
	Threshold of ML environment and MM environment.
005	Absolute Humidity: Threshold 3	*ENG	[0.00 to 100.00 / 15.00 / 0.01g/m^3/step]
	Threshold of MM environment and MH environment.
006	Absolute Humidity: Threshold 4	*ENG	[0.00 to 100.00 / 22.00 / 0.01g/m^3/step]
	Threshold of MH environment and HH environment.
007	Temp FC: Display	*ENG	[0 to 100 / 0 / 1deg/step]
	Temperature detected with temperature / humidity sensor when controlling Electrify AC of latest main and subs FC mode.
008	Relative Humidity FC : Display	*ENG	[0 to 100 / 0 / 1%RH/step]
	Relative temperature detected with temperature / humidity sensor when controlling Electrify AC of latest main and subs FC mode.
009	Absolute Humidity FC : Display	*ENG	[0.00 to 100.00 / 0.00 / 0.01g/m^3/step]
	Absolute temperature detected with temperature / humidity sensor when controlling Electrify AC of latest main and subs FC mode.
010	Environmental Bk: Display	*ENG	[0 to 0 / 0 / 1/step]
	Environment class divided based on the temperature / humidity sensor information when controlling Electrify AC of latest main & subs monochrome Bk mode.
011	Temp Bk.: Display	*ENG	[0 to 100 / 0 / 1deg/step]
	Temperature detected by the temperature / humidity sensor when controlling Electrify AC of latest main & subs monochrome Bk mode.

Main SP Tables-2-1

012	Relative Humidity Bk : Display	*ENG	[0 to 100 / 0 / 1%RH/step]
	Relative temperature detected by the temperature / humidity sensor when controlling Electrify AC of latest main & subs monochrome Bk mode.
013	Absolute Humidity Bk : Display	*ENG	[0.00 to 100.00 / 0.00 / 0.01g/m^3/step]
	Absolute temperature detected by the temperature / humidity sensor when controlling Electrify AC of latest main & subs monochrome Bk mode.

2014	[Charge AC Control: Setting]
001	Exec Interval: Power ON	*ENG	[0 to 2000 / 500 / 1page/step]
	Page interval to do main control when Power ON, recover from energy save mode, front door close.
002	Exec Interval: Print	*ENG	[0 to 2000 / 0 / 1page/step]
	Page interval to do main control when printing, finish printing.
003	Page Interval	*ENG	[0 to 500 / 10 / 1page/step]
	Page interval to decide to adjust sub when printing in standard speed.
004	Temperature	*ENG	[0 to 99 / 35 / 1deg/step]
	Temperature threshold for sub control execute decision,
005	Relative Humidity	*ENG	[0 to 99 / 50 / 1%RH/step]
	Threshold of relative humidity conditions to do sub adjustments.
006	Absolute Humidity	*ENG	[0 to 99 / 12 / 1g/m^3/step]
	Threshold of absolute Temperature conditions to do sub adjustments.

SP Mode Tables

Main SP Tables-2-1

007	Temp Threshold M	*ENG	[0 to 99 / 10 / 1deg/step]
	Temperature variation threshold for deciding of executing main control. 0: Execute every time when set.
008	RH Threshold M	*ENG	[0 to 99 / 50 / 1%RH/step]
	Relative humidity variation threshold for deciding of executing main adjust. 0: Execute every time.
009	AH Threshold M	*ENG	[0 to 99 / 6 / 1g/m^3/step]
	Relative humidity variation threshold for deciding of executing main adjust. 0: Execute every time.
010	Temp Threshold S	*ENG	[0.0 to 20.0 / 1.0 / 0.1deg]
	Temperature variation threshold to do sub adjust. 0: Do every time
011	RH Threshold S	*ENG	[0 to 50 / 5 / 1%RH/step]
	Relative humidity variation threshold to do sub adjust. 0: Do every time
012	AH Threshold S	*ENG	[0.0 to 20.0 / 1.0 / 0.1g/m^3/step]
	Absolute humidity variation threshold to do sub adjust. 0: Do every time if conditions match.
013	Non-use Time	*ENG	[0 to 1440 / 360 / 10min./step]
	Threshold of time stopping photoreceptor continuously for main adjust. 0: Do not.
014	AC Current Error Detection	*ENG	[0 or 1 / 0 / 1/step]
	Flag to decide whether to adjust AC when SC491 is detected.

Main SP Tables-2-1

2015	[Charge AC Adj: Result]
001	Bk	*ENG	[0 to 9 / 0 / 1/step]
	Result of AC adjust control for Bk (main / sub common)
002	C	*ENG	[0 to 9 / 0 / 1/step]
	Result of AC adjust control for C (main / sub common)
003	M	*ENG	[0 to 9 / 0 / 1/step]
	Result of AC adjust control for M (main / sub common)
004	Y	*ENG	[0 to 9 / 0 / 1/step]
	Result of AC adjust control for Y (main / sub common)

2020	[Background Pot Correction Set]
001	Temperature	*ENG	[0 to 19 / 15 / 1deg/step]
	Temperature threshold for calculating Electrify roller fatigue.
002	Absolute Humidity	*ENG	[0 to 99 / 6 / 1g/m^3/step]
	Absolute humidity threshold for calculating Electrify roller fatigue.
003	Print Page Counter	*ENG	[0 to 999 / 0 / 1page/step]
	Printing counter for multi-step correction.
004	Print Pages Threshold	*ENG	[0 to 999 / 10 / 1page/step]
	Printing pages threshold when Multi-step correction.
005	Temp Thresh	*ENG	[20 to 99 / 20 / 1deg/step]
	Temperature threshold 2 for calculating Electrify roller fatigue.
011	Coefficient a: K	*ENG	[0.00 to 1.00 / 0.06 / 0.01/step]
	Coefficient a, K for calculating Electrify roller fatigue.
012	Coefficient a: C	*ENG	[0.00 to 1.00 / 0.06 / 0.01/step]
	Coefficient a, C for calculating Electrify roller fatigue.

SP Mode Tables

Main SP Tables-2-1

013	Coefficient a: M	*ENG	[0.00 to 1.00 / 0.06 / 0.01/step]
	Coefficient a, M for calculating Electrify roller fatigue.
014	Coefficient a: Y	*ENG	[0.00 to 1.00 / 0.06 / 0.01/step]
	Coefficient a, Y for calculating Electrify roller fatigue.
015	Coefficient b: K	*ENG	[0.00 to 9.00 / 0.50 / 0.01/step]
	Coefficient b, K for calculating Electrify roller fatigue.
016	Coefficient b: C	*ENG	[0.00 to 9.00 / 0.50 / 0.01/step]
	Coefficient b, C for calculating Electrify roller fatigue.
017	Coefficient b: M	*ENG	[0.00 to 9.00 / 0.50 / 0.01/step]
	Coefficient b, M for calculating Electrify roller fatigue.
018	Coefficient b: Y	*ENG	[0.00 to 9.00 / 0.50 / 0.01/step]
	Coefficient b, Y for calculating Electrify roller fatigue.

2021	[Background Pot Correction]
001	Display:K	*ENG	[0 to 90 / 0 / 1V/step]
	DC bias correction value, K
002	Display:C	*ENG	[0 to 90 / 0 / 1V/step]
	DC bias correction value, C
003	Display:M	*ENG	[0 to 90 / 0 / 1V/step]
	DC bias correction value, M
004	Display:Y	*ENG	[0 to 90 / 0 / 1V/step]
	DC bias correction value, Y
005	Setting1:K	*ENG	[0 to 90 / 10 / 10V/step]
	Electric potential correction amount 1 against Electrify roller fatigue amount, K
006	Setting1:C	*ENG	[0 to 90 / 10 / 10V/step]
	Electric potential correction amount 1 against Electrify roller fatigue amount, C

Main SP Tables-2-1

007	Setting1:M	*ENG	[0 to 90 / 10 / 10V/step]
	Electric potential correction amount 1 against Electrify roller fatigue amount, M
008	Setting1:Y	*ENG	[0 to 90 / 10 / 10V/step]
	Electric potential correction amount 1 against Electrify roller fatigue amount, Y
009	Setting2:K	*ENG	[0 to 90 / 20 / 10V/step]
	Electric potential correction amount 1 against Electrify roller fatigue amount, K
010	Setting2:C	*ENG	[0 to 90 / 20 / 10V/step]
	VC calculating coefficient DC Electrify.
011	Setting2:M	*ENG	[0 to 90 / 20 / 10V/step]
	Electric potential correction amount 2 against Electrify roller fatigue amount, M
012	Setting2:Y	*ENG	[0 to 90 / 20 / 10V/step]
	Electric potential correction amount 2 against Electrify roller fatigue amount, Y
013	Setting3:K	*ENG	[0 to 90 / 30 / 5V/step]
	Electric potential correction amount 3 against Electrify roller fatigue amount, K
014	Setting3:C	*ENG	[0 to 90 / 30 / 5V/step]
	Electric potential correction amount 3 against Electrify roller fatigue amount, C
015	Setting3:M	*ENG	[0 to 90 / 30 / 5V/step]
	Electric potential correction amount 3 against Electrify roller fatigue amount, M
016	Setting3:Y	*ENG	[0 to 90 / 30 / 5V/step]
	Electric potential correction amount 3 against Electrify roller fatigue amount, Y
017	Setting4:K	*ENG	[0 to 90 / 40 / 5V/step]
	Electric potential correction amount 4 against Electrify roller fatigue amount, K
018	Setting4:C	*ENG	[0 to 90 / 40 / 5V/step]
	Electric potential correction amount 4 against Electrify roller fatigue amount, C
019	Setting4:M	*ENG	[0 to 90 / 40 / 5V/step]
	Electric potential correction amount 4 against Electrify roller fatigue amount, M

SP Mode Tables

Main SP Tables-2-1

020	Setting4:Y	*ENG	[0 to 90 / 40 / 5V/step]
	Electric potential correction amount 4 against Electrify roller fatigue amount, Y
021	Setting5:K	*ENG	[0 to 90 / 10 / 1V/step]
	Variation amount 5 K, for correcting electric potential phase when environment changes.
022	Setting5:C	*ENG	[0 to 90 / 10 / 1V/step]
	Variation amount 5 C, for correcting electric potential phase when environment changes.
023	Setting5:M	*ENG	[0 to 90 / 10 / 1V/step]
	Variation amount 5 M, for correcting electric potential phase when environment changes.
024	Setting5:Y	*ENG	[0 to 90 / 10 / 1V/step]
	Variation amount 5 Y, for correcting electric potential phase when environment changes.
025	Setting6:K	*ENG	[-90 to 90 / 2 / 1V/step]
	Electric potential correction amount 6 K, against Electrify roller total rotating time.
026	Setting6:C	*ENG	[-90 to 90 / 2 / 1V/step]
	Electric potential correction amount 6 C, against Electrify roller total rotating time.
027	Setting6:M	*ENG	[-90 to 90 / 2 / 1V/step]
	Electric potential correction amount 6,M, against Electrify roller total rotating time.
028	Setting6:Y	*ENG	[-90 to 90 / 2 / 1V/step]
	Electric potential correction amount 6 Y, against Electrify roller total rotating time.
029	Display:Energized:K	*ENG	[0 to 90 / 0 / 1V/step]
	Voltage correction value K, from Electrify roller fatigue.

Main SP Tables-2-1

030	Display:Energized:C	*ENG	[0 to 90 / 0 / 1V/step]
	Voltage correction value C, from Electrify roller fatigue.
031	Display:Energized:M	*ENG	[0 to 90 / 0 / 1V/step]
	Voltage correction value M, from Electrify roller fatigue.
032	Display:Energized:Y	*ENG	[0 to 90 / 0 / 1V/step]
	Voltage correction value Y, from Electrify roller fatigue.
033	Display:Total Rotation:K	*ENG	[0 to 30 / 0 / 1V/step]
	Voltage correction value K, from Electrify roller total electrification.
034	Display:Total Rotation:C	*ENG	[0 to 30 / 0 / 1V/step]
	Voltage correction value C, from Electrify roller total electrification.
035	Display:Total Rotation:M	*ENG	[0 to 30 / 0 / 1V/step]
	Voltage correction value M, from Electrify roller total electrification.
036	Display:Total Rotation:Y	*ENG	[0 to 30 / 0 / 1V/step]
	Voltage correction value Y, from Electrify roller total electrification.
037	Split Number n: K	*ENG	[1 to 99 / 15 / 1/step]
	Coefficient K, for setting electric potential to multiple steps from total electrification time.
038	Split Number n: C	*ENG	[1 to 99 / D146: 15, D147: 15, D148: 15, D149: 13, D150: 10 / 1/step]
	Coefficient C, for setting electric potential to multiple steps from total electrification time.
039	Split Number n: M	*ENG	[1 to 99 / D146: 15, D147: 15, D148: 15, D149: 13, D150: 10 / 1/step]
	Coefficient M, for setting electric potential to multiple steps from total electrification time.

SP Mode Tables

Main SP Tables-2-1

040

Split Number n: Y

*ENG

[1 to 99 / D146: 15, D147: 15,

D148: 15, D149: 13, D150: 10 /

1/step]

Coefficient Y, for setting electric potential to multiple steps from total electrification time.

041

Display:Energized for target value:K

*ENG

[0 to 90 / 0 / 1V/step]

Target value K, for voltage correction from Electrify roller fatigue.

042

Display:Energized for target value:C

*ENG

[0 to 90 / 0 / 1V/step]

Target value C, for voltage correction from Electrify roller fatigue.

043

Display:Energized for target value:M

*ENG

[0 to 90 / 0 / 1V/step]

Target value M, for voltage correction from Electrify roller fatigue.

044

Display:Energized for target value:Y

*ENG

[0 to 90 / 0 / 1V/step]

Target value Y, for voltage correction from Electrify roller fatigue.

2022	[Charge R Running Par]
001	Display:K	*ENG	[0 to 999999 / 0 / 1/step]
	Value K, showing the electrification fatigue amount of Electrify roller.
002	Display:C	*ENG	[0 to 999999 / 0 / 1/step]
	Value C, showing the electrification fatigue amount of Electrify roller.
003	Display:M	*ENG	[0 to 999999 / 0 / 1/step]
	Value M, showing the electrification fatigue amount of Electrify roller.
004	Display:Y	*ENG	[0 to 999999 / 0 / 1/step]
	Value Y, showing the electrification fatigue amount of Electrify roller.
005	PCU Rotation Time After Correction: K	*ENG	[0 to 9999999 / 0 / 1/step]

Main SP Tables-2-1

	Calculation value K, for calculating temporary value when RTC can not be acquired.
006	PCU Rotation Time After Correction: C	*ENG	[0 to 9999999 / 0 / 1/step]
	Calculation value C, for calculating temporary value when RTC can not be acquired.
007	PCU Rotation Time After Correction: M	*ENG	[0 to 9999999 / 0 / 1/step]
	Calculation value M, for calculating temporary value when RTC can not be acquired.
008	PCU Rotation Time After Correction: Y	*ENG	[0 to 9999999 / 0 / 1/step]
	Calculation value Y, for calculating temporary value when RTC can not be acquired.
009	Threshold1:K	*ENG	[0 to 4000 / 30 / 1/step]
	Threshold 1 K, against Electrify roller fatigue amount.
010	Threshold1:C	*ENG	[0 to 4000 / 30 / 1/step]
	Threshold 1 C, against Electrify roller fatigue amount.
011	Threshold1:M	*ENG	[0 to 4000 / 30 / 1/step]
	Threshold 1 M, against Electrify roller fatigue amount.
012	Threshold1:Y	*ENG	[0 to 4000 / 30 / 1/step]
	Threshold 1 Y, against Electrify roller fatigue amount.
013	Threshold2:K	*ENG	[0 to 4000 / 70 / 1/step]
	Threshold 2 K, against Electrify roller fatigue amount.
014	Threshold2:C	*ENG	[0 to 4000 / 70 / 1/step]
	Threshold 2 C, against Electrify roller fatigue amount.
015	Threshold2:M	*ENG	[0 to 4000 / 70 / 1/step]
	Threshold 2 M, against Electrify roller fatigue amount.

SP Mode Tables

Main SP Tables-2-1

016	Threshold2:Y	*ENG	[0 to 4000 / 70 / 1/step]
	Threshold 2 Y, against Electrify roller fatigue amount.
017	Threshold3:K	*ENG	[0 to 4000 / 150 / 1/step]
	Threshold 3 K, against Electrify roller fatigue amount.
018	Threshold3:C	*ENG	[0 to 4000 / 150 / 1/step]
	Threshold 3 C, against Electrify roller fatigue amount.
019	Threshold3:M	*ENG	[0 to 4000 / 150 / 1/step]
	Threshold 3 M, against Electrify roller fatigue amount.
020	Threshold3:Y	*ENG	[0 to 4000 / 150 / 1/step]
	Threshold 3 Y, against Electrify roller fatigue amount.
021	Threshold4:K	*ENG	[0 to 4000 / 250 / 1/step]
	Threshold 4 K, against Electrify roller fatigue amount.
022	Threshold4:C	*ENG	[0 to 4000 / 250 / 1/step]
	Threshold 4 C, against Electrify roller fatigue amount.
023	Threshold4:M	*ENG	[0 to 4000 / 250 / 1/step]
	Threshold 4 M, against Electrify roller fatigue amount.
024	Threshold4:Y	*ENG	[0 to 4000 / 250 / 1/step]
	Threshold 4 Y, against Electrify roller fatigue amount.
025	Prev Correction Calculation Bk:Year	*ENG	[0 to 99 / 0 / 1year/step]
	Calculation time of last correction: Year, K.
026	Prev Correction Calculation Bk:Month	*ENG	[1 to 12 / 1 / 1month/step]
	Calculation time of last correction: Month, K.
027	Prev Correction Calculation Bk:Day	*ENG	[1 to 31 / 1 / 1day/step]
	Calculation time of last correction: Day, K.

Main SP Tables-2-1

028

Prev Correction Calculation Bk:Hour

*ENG

[0 to 23 / 0 / 1hour/step]

Calculation time of last correction: Hour, K.

029

Prev Correction Calculation Bk:Minute

*ENG

[0 to 59 / 0 / 1minute/step]

Calculation time of last correction: Minute, K.

030

Rotation At Prev Correction: PCU: Bk

*ENG

[0 to 999999999 / 0 / 1mm/step]

PCU distance when last correction: Year, K.

031

Rotation At Prev Correction: PCU: C

*ENG

[0 to 999999999 / 0 / 1mm/step]

PCU distance when last correction: Year, C.

032

Rotation At Prev Correction: PCU: M

*ENG

[0 to 999999999 / 0 / 1mm/step]

PCU distance when last correction: Year, M.

033

Rotation At Prev Correction: PCU: Y

*ENG

[0 to 999999999 / 0 / 1mm/step]

PCU distance when last correction: Year, Y.

2101

[Registration Correction]

001

Color Main Dot: Bk

*ENG

[-512 to 511 / 0 / 1dot/step]

Adjusts main scan register of BK color.

 Value increase: image shifts to right facing the paper.

 Value decrease: image shifts to left facing the paper.

CMY colors can be adjusted to BK color position if execute MUSIC after operating this SP.

SP Mode Tables

Main SP Tables-2-1

002	Color Main Dot: Ma	*ENG	[-512 to 511 / 0 / 1dot/step]
	Adjusts main scan register of BK color.  Value increase: image shifts to right facing the paper.  Value decrease: image shifts to left facing the paper. By operating this SP, main scan position can be changed, but if MUSIC is executed, automatically will be adjusted to BK position.
003	Color Main Dot: Cy	*ENG	[-512 to 511 / 0 / 1dot/step]
	Adjusts main scan register of BK color.  Value increase: image shifts to right facing the paper.  Value decrease: image shifts to left facing the paper. By operating this SP, main scan position can be changed, but if MUSIC is executed, automatically will be adjusted to BK position.
004	Color Main Dot: Ye	*ENG	[-512 to 511 / 0 / 1dot/step]
	Adjusts main scan register of BK color.  Value increase: image shifts to right facing the paper.  Value decrease: image shifts to left facing the paper. By operating this SP, main scan position can be changed, but if MUSIC is executed, automatically will be adjusted to BK position.
005	Color Sub Line: Bk	*ENG	[-16384 to 16383 / 0 / 1line/step]
	For BK color, even using this SP, sub scan image position against paper will not change, mush be adjust with paper feed timing.
006	Color Sub Line: Ma	*ENG	[-16384 to 16383 / 0 / 1line/step]
	 Value increase: image shifts to downer facing the paper.  Value decrease: image shifts to upper facing the paper. By operating this SP, sub scan position can be changed, but if MUSIC is executed, automatically will be adjusted to BK position.
007	Color Sub Line: Cy	*ENG	[-16384 to 16383 / 0 / 1line/step]
	 Value increase: image shifts to downer facing the paper.  Value decrease: image shifts to upper facing the paper. By operating this SP, sub scan position can be changed, but if MUSIC is executed, automatically will be adjusted to BK position.

Main SP Tables-2-1

008

Color Sub Line: Ye

*ENG

[-16384 to 16383 / 0 / 1line/step]

 Value increase: image shifts to downer facing the paper.

 Value decrease: image shifts to upper facing the paper.

By operating this SP, sub scan position can be changed, but if MUSIC is executed, automatically will be adjusted to BK position.

2102	[Magnification Adjustment]
2102	Adjusts main scan lower speed scale for BK color.  Value increase: image stretches.  Value decrease: image shrinks CMY color scale will fit to standard BK speed after executing MUSIC; only BK color will have a different scale in the image even with out executing MUSIC after this SP.
001	Main Mag.: Standard Speed: Bk	*ENG	[-2.000 to 2.000 / 0.000 / 0.001%/step]
002	Main Mag.: Middle Speed: Bk	*ENG
003	Main Mag.: Low Speed: Bk	*ENG
2102	[Magnification Adjustment]
2102	Adjusts main scan scale.  Value increase: image stretches.  Value decrease: image shrinks With operating this SP, scale can be changed, but if MUSIC is executed after, automatically will be adjusted so fit standard speed BK color scale.
004	Main Mag.: Standard Speed: Ma	*ENG	[-2.000 to 2.000 / 0.000 / 0.001%/step]
005	Main Mag.: Middle Speed: Ma	*ENG
006	Main Mag.: Low Speed: Ma	*ENG
007	Main Mag.: Standard Speed: Cy	*ENG
008	Main Mag.: Middle Speed: Cy	*ENG
009	Main Mag.: Low Speed: Cy	*ENG

SP Mode Tables

Main SP Tables-2-1

010

Main Mag.: Standard Speed: Ye

*ENG

011

Main Mag.: Middle Speed: Ye

*ENG

012

Main Mag.: Low Speed: Ye

*ENG

2102

[Magnification Adjustment]

Adjusts scale against standard speed BK.

 Value increase: image stretches.

 Value decrease: image shrinks

With operating this SP, scale can be changed, but if MUSIC is executed after, automatically will be adjusted so to match standard speed BK color scale

028

Color Main Mag.: High Speed: Ma

*ENG

[-2.000 to 2.000 / 0.000 /

0.001%/step]

031

Color Main Mag.: High Speed: Cy

*ENG

034

Color Main Mag.: High Speed: Ye

*ENG

2102

[Main Scan Beam Pitch Adj.]

037

Bk: 1st-2nd

*ENG

[0.00 to 100.00 / 12.15 /

0.01dot/step]

Adjusts main scan beam pitch against BK color LD1 Only for factory adjust.

038

Bk: 1st-3rd

*ENG

[0.00 to 100.00 / 24.29 /

0.01dot/step]

Adjusts main scan beam pitch against BK color LD1 Only for factory adjust.

039

Bk: 1st-4th

*ENG

[0.00 to 100.00 / 36.44 /

0.01dot/step]

Adjusts main scan beam pitch against BK color LD1 Only for factory adjust.

Main SP Tables-2-1

040

Ma: 1st-2nd

*ENG

[0.00 to 100.00 / 12.15 /

0.01dot/step]

Adjusts main scan beam pitch against M color LD1 Only for factory adjust.

041

Ma: 1st-3rd

*ENG

[0.00 to 100.00 / 24.29 /

0.01dot/step]

Adjusts main scan beam pitch against M color LD1 Only for factory adjust.

042

Ma: 1st-4th

*ENG

[0.00 to 100.00 / 36.44 /

0.01dot/step]

Adjusts main scan beam pitch against M color LD1 Only for factory adjust.

043

Cy: 1st-2nd

*ENG

[0.00 to 100.00 / 12.15 /

0.01dot/step]

Adjusts main scan beam pitch against M color LD1 Only for factory adjust.

044

Cy: 1st-3rd

*ENG

[0.00 to 100.00 / 24.29 /

0.01dot/step]

Adjusts main scan beam pitch against M color LD1 Only for factory adjust.

045

Cy: 1st-4th

*ENG

[0.00 to 100.00 / 36.44 /

0.01dot/step]

Adjusts main scan beam pitch against M color LD1 Only for factory adjust.

046

Ye: 1st-2nd

*ENG

[0.00 to 100.00 / 12.15 /

0.01dot/step]

Adjusts main scan beam pitch against Y color LD1 Only for factory adjust.

SP Mode Tables

Main SP Tables-2-1

047

Ye: 1st-3rd

*ENG

[0.00 to 100.00 / 24.29 /

0.01dot/step]

Adjusts main scan beam pitch against Y color LD1 Only for factory adjust.

048

Ye: 1st-4th

*ENG

[0.00 to 100.00 / 36.44 /

0.01dot/step]

Adjusts main scan beam pitch against Y color LD1 Only for factory adjust.

2103	[Erase Margin Adjustment]
001	Lead Edge Width	*ENG	[0.0 to 9.9 / 4.2 / 0.1mm/step]
	Adjusts trimming for sub scan lead edge.  Value increase: Trim wider.  Value decrease: Trim narrower.
002	Trail. Edge Width	*ENG	[0.0 to 9.9 / 4.2 / 0.1mm/step]
	Adjusts trimming for sub scan trailing edge.  Value increase: Trim wider.  Value decrease: Trim narrower. When printing, follow margin set with application.
003	Left	*ENG	[0.0 to 9.0 / 2.0 / 0.1mm/step]
	Adjusts trimming for sub scan left edge.  Value increase: Trim wider.  Value decrease: Trim narrower. When printing, follow margin set with application.
004	Right	*ENG	[0.0 to 9.0 / 2.0 / 0.1mm/step]
	Adjusts trimming for sub scan right edge.  Value increase: Trim wider.  Value decrease: Trim narrower. When printing, follow margin set with application.

Main SP Tables-2-1

2103	[Erase Margin Adjustment]
2103	Sets trim for duplex.
006	Duplex Trail. L Size	*ENG	[0.0 to 4.0 / 1.0 / 0.1mm/step]
007	Duplex Trail. M Size	*ENG	[0.0 to 4.0 / 0.8 / 0.1mm/step]
008	Duplex Trail. S Size	*ENG	[0.0 to 4.0 / 0.6 / 0.1mm/step]
009	Duplex Left Edge	*ENG	[0.0 to 1.5 / 0.3 / 0.1mm/step]
010	Duplex Right Edge	*ENG	[0.0 to 1.5 / 0.3 / 0.1mm/step]
011	Duplex Trail. L Size:Thick	*ENG	[0.0 to 4.0 / 1.0 / 0.1mm/step]
012	Duplex Trail. M Size:Thick	*ENG	[0.0 to 4.0 / 0.8 / 0.1mm/step]
013	Duplex Trail. S Size:Thick	*ENG	[0.0 to 4.0 / 0.6 / 0.1mm/step]
014	Duplex Left Edge:Thick	*ENG	[0.0 to 1.5 / 0.3 / 0.1mm/step]
015	Duplex Right Edge:Thick	*ENG	[0.0 to 1.5 / 0.3 / 0.1mm/step]

2106	[Polygon Rotation Time]
	Sets pre-rotating time/ post-rotating time for polygon motor.
001	Warming-Up	*ENG	[0 to 60 / 10 / 1sec/step]
	Sets pre-rotating time for polygon motor. With touching the operating during standby, polygon motor will pre-rotate. With this, waiting time will be shorter.
002	Job End	*ENG	[0.0 to 60.0 / 0.1 / 0.1sec/step]
	Sets post-rotating time for polygon motor. Polygon motor will post-rotate after printing. If a print order come during post-rotation, printing will start faster.

SP Mode Tables

2107	[Image Parameter]
001	Image Gamma Flag	ENG	[0 or 1 / 1 / 1/step]
	Turns writing Gamma property ON/OFF. For Design evaluation.
002	Shading Correction Flag	*ENG	[0 or 1 / 0 / 1/step]
	Turns shading area correction ON/OFF. For Design evaluation.

2107	[Image Parameter]
001	Image Gamma Flag	ENG	[0 or 1 / 1 / 1/step]
	Turns writing Gamma property ON/OFF. For Design evaluation.
002	Shading Correction Flag	*ENG	[0 or 1 / 0 / 1/step]
	Turns shading area correction ON/OFF. For Design evaluation.

2107	[Image Parameter]
001	Image Gamma Flag	ENG	[0 or 1 / 1 / 1/step]
	Turns writing Gamma property ON/OFF. For Design evaluation.
002	Shading Correction Flag	*ENG	[0 or 1 / 0 / 1/step]
	Turns shading area correction ON/OFF. For Design evaluation.

2109	[Test Pattern]
003	Pattern Selection		ENG	[0 to 23 / 0 / 1/step]
	Select patterns.
	0	None	12	Independent Pattern (2dot)
	1	Vertical Line (1dot)	13	Independent Pattern (4dot)
	2	Vertical Line (2dot)	14	Trimming Area
	3	Horizontal Line (1dot)	15	Hound's Tooth Check (Vertical)
	4	Horizontal Line (2dot)	16	Hound's Tooth Check (Horizontal)
	5	Grid Vertical Line	17	Band (Horizontal)
	6	Grid Horizontal Line	18	Band (Vertical)
	7	Grid Pattern Small	19	Checker Flag Pattern
	8	Grid Pattern Large	20	Grayscale (Vertical Margin)
	9	Argyle Pattern Small	21	Grayscale (Horizontal Margin)
	10	Argyle Pattern Large	22	Two Beam Density Pattern
	11	Independent Pattern (1dot)	23	Full Dot Pattern
005	Color Selection		ENG	[1 to 4 / 1 / 1/step] 1: All Color 2: Ma 3: Ye 4: Cy
005	Selects output color for writing test pattern.

2109	[Test Pattern]
003	Pattern Selection		ENG	[0 to 23 / 0 / 1/step]
	Select patterns.
	0	None	12	Independent Pattern (2dot)
	1	Vertical Line (1dot)	13	Independent Pattern (4dot)
	2	Vertical Line (2dot)	14	Trimming Area
	3	Horizontal Line (1dot)	15	Hound's Tooth Check (Vertical)
	4	Horizontal Line (2dot)	16	Hound's Tooth Check (Horizontal)
	5	Grid Vertical Line	17	Band (Horizontal)
	6	Grid Horizontal Line	18	Band (Vertical)
	7	Grid Pattern Small	19	Checker Flag Pattern
	8	Grid Pattern Large	20	Grayscale (Vertical Margin)
	9	Argyle Pattern Small	21	Grayscale (Horizontal Margin)
	10	Argyle Pattern Large	22	Two Beam Density Pattern
	11	Independent Pattern (1dot)	23	Full Dot Pattern
005	Color Selection		ENG	[1 to 4 / 1 / 1/step] 1: All Color 2: Ma 3: Ye 4: Cy
005	Selects output color for writing test pattern.

2109	[Test Pattern]
003	Pattern Selection		ENG	[0 to 23 / 0 / 1/step]
	Select patterns.
	0	None	12	Independent Pattern (2dot)
	1	Vertical Line (1dot)	13	Independent Pattern (4dot)
	2	Vertical Line (2dot)	14	Trimming Area
	3	Horizontal Line (1dot)	15	Hound's Tooth Check (Vertical)
	4	Horizontal Line (2dot)	16	Hound's Tooth Check (Horizontal)
	5	Grid Vertical Line	17	Band (Horizontal)
	6	Grid Horizontal Line	18	Band (Vertical)
	7	Grid Pattern Small	19	Checker Flag Pattern
	8	Grid Pattern Large	20	Grayscale (Vertical Margin)
	9	Argyle Pattern Small	21	Grayscale (Horizontal Margin)
	10	Argyle Pattern Large	22	Two Beam Density Pattern
	11	Independent Pattern (1dot)	23	Full Dot Pattern
005	Color Selection		ENG	[1 to 4 / 1 / 1/step] 1: All Color 2: Ma 3: Ye 4: Cy
005	Selects output color for writing test pattern.

Main SP Tables-2-1

006	Density: Bk	ENG	[0 to 15 / 15 / 1/step]
	Sets test patterns density.  Value increase: Deeper  Value decrease: Thinner
007	Density: Ma	ENG	[0 to 15 / 15 / 1/step]
	Sets test patterns density.  Value increase: Deeper  Value decrease: Thinner
008	Density: Cy	ENG	[0 to 15 / 15 / 1/step]
	Sets test patterns density.  Value increase: Deeper  Value decrease: Thinner
009	Density: Ye	ENG	[0 to 15 / 15 / 1/step]
	Sets test patterns density.  Value increase: Deeper  Value decrease: Thinner

2110

[LD Driver]

LD Driver error flag

001

Error Bk

*ENG

[0x0000 to 0xFFFF / 0x0000 / 1/step]

LD Driver error flag Bk color.

002

Error Ma

*ENG

[0x0000 to 0xFFFF / 0x0000 / 1/step]

LD Driver error flag Ma color (For only model D148/D149/D150. Abxyz models does not use)

003

Error Cy

*ENG

[0x0000 to 0xFFFF / 0x0000 / 1/step]

LD Driver error flag Cy color (For only model D148/D149/D150. Abxyz models does not use)

SP Mode Tables

004	Error Ye	*ENG	[0x0000 to 0xFFFF / 0x0000 / 1/step]
	LD Driver error flag Ye color (For abxyz/model D148/D149/D150)
005	Writing Unit Adj. Transfer	ENG	[0 or 1 / 0 / 1/step]
	Execution flag to download adjustment values of writing unit to main units SP. Executes when replacing the writing unit or assembling main unit

004	Error Ye	*ENG	[0x0000 to 0xFFFF / 0x0000 / 1/step]
	LD Driver error flag Ye color (For abxyz/model D148/D149/D150)
005	Writing Unit Adj. Transfer	ENG	[0 or 1 / 0 / 1/step]
	Execution flag to download adjustment values of writing unit to main units SP. Executes when replacing the writing unit or assembling main unit

004	Error Ye	*ENG	[0x0000 to 0xFFFF / 0x0000 / 1/step]
	LD Driver error flag Ye color (For abxyz/model D148/D149/D150)
005	Writing Unit Adj. Transfer	ENG	[0 or 1 / 0 / 1/step]
	Execution flag to download adjustment values of writing unit to main units SP. Executes when replacing the writing unit or assembling main unit

2111	[Forced Line Position Adj.]
	Executes force correction of color match.
001	Mode a	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode a ( fine-tune x 2)
002	Mode b	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode b ( fine-tune x 1)
003	Mode c	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode c (rough-tune x 1)
004	Mode d	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode d (rough-tune then fine-tune)

2111	[Forced Line Position Adj.]
	Executes force correction of color match.
001	Mode a	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode a ( fine-tune x 2)
002	Mode b	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode b ( fine-tune x 1)
003	Mode c	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode c (rough-tune x 1)
004	Mode d	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode d (rough-tune then fine-tune)

2111	[Forced Line Position Adj.]
	Executes force correction of color match.
001	Mode a	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode a ( fine-tune x 2)
002	Mode b	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode b ( fine-tune x 1)
003	Mode c	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode c (rough-tune x 1)
004	Mode d	ENG	[0 or 1 / 0 / 1/step]
	Executes MUSIC mode d (rough-tune then fine-tune)

Main SP Tables-2-1

2112	[TM/ID Sensor Check]
001	Execute	ENG	[0 or 1 / 0 / 1/step]
	Executes test mode for Image transfer belt / TMP sensor.
010	General:FCR	*ENG	[0 to 999 / 0 / 1/step]
	Shows test results for Image transfer belt / TMP sensor test mode, with 3bits / in the order of [Front][Center][Rear].
020	Threshold Setting	*ENG	[0.00 to 3.50 / 1.90 / 0.01V/step]

Main SP Tables-2-1

Sets edge detecting threshold value of Image transfer belt / TMP sensor test mode.

The results will turn out as following in Image transfer belt / TMP sensors test mode.

 When TMP sensor detection value is larger than this setting value: No problems.

 When TMP sensor detection value is smaller than this setting value: Edge detected.

2115

[Gamma Correction]

001

Low CPP edge Correction

*ENG

[0 to 100 / 80 / 1%/step]

Sets gamma correction value of valid pixel for low CPP edge process.

 Value increase: Deeper density

 Value decrease: thinner density

2117	[Skew Adjustment]
001	Pulse: M	*ENG	[-75 to 75 / 0 / 1pulse/step]
	M: skew adjust: input
002	Pulse: C	*ENG	[-75 to 75 / 0 / 1pulse/step]
	C: skew adjust: input
003	Pulse: Y	*ENG	[-99 to 99 / 0 / 1pulse/step]
	Y: skew adjust: input

2118	[Skew Adjustment]
001	Execute: M	ENG	[0 or 1 / - / -]
	M: skew adjust: execute
002	Execute: C	ENG	[0 or 1 / - / -]
	C: skew adjust: execute
003	Execute: Y	ENG	[0 or 1 / - / -]
	Y: skew adjust: execute

SP Mode Tables

Main SP Tables-2-1

2119	[Skew Adjustment Display]
001	M	*ENG	[-75 to 75 / 0 / 1pulse/step]
	M: skew current location: display.
002	C	*ENG	[-75 to 75 / 0 / 1pulse/step]
	C: skew current location: display.
003	Y	*ENG	[-99 to 99 / 0 / 1pulse/step]
	Y: skew current location: display.

2120

[Thick Paper Skew Adj]

001

On/Off

*ENG

[0 or 1 / 0 / 1/step]

Corrects thick paper skew.

2121

[Skew Adjust Coefficient]

001

Coefficient

*ENG

[0 to 2 / 0 / 1/step]

Correcting coefficient for skew.

2140

[TM/ID Sensor Check Result]

005

PWM: Front

ENG

[0 to 1023 / 0 / 1/step]

Saves / Refreshes PWM setting value of TMP sensor [Front] to this setting value when Vsg adjustment is done.

From then on, PWM setting value will be this setting value during belt check. When Vsg adjust fails, saving / refreshing will not be done to this setting

Main SP Tables-2-1

006	PWM: Center	*ENG	[0 to 1023 / 0 / 1/step]
	Saves / Refreshes PWM setting value of TMP sensor [Center] to this setting value when Vsg adjustment is done. From then on, PWM setting value will be this setting value during belt check. When Vsg adjust fails, saving / refreshing will not be done to this setting
007	PWM: Rear	*ENG	[0 to 1023 / 0 / 1/step]
	Saves / Refreshes PWM setting value of TMP sensor [Rear] to this setting value when Vsg adjustment is done. From then on, PWM setting value will be this setting value during belt check. When Vsg adjust fails, saving / refreshing will not be done to this setting

2141	[TM/ID Sensor Check Result]
005	Average: Front	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Saves / Refreshes TMP sensor [Front] detecting result average data to this SP from result of Image transfer belt / TMP sensor check mode.
006	Average: Center	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Saves / Refreshes TMP sensor [Center] detecting result average data to this SP from result of Image transfer belt / TMP sensor check mode.
007	Average: Rear	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Saves / Refreshes TMP sensor [Rear] detecting result average data to this SP from result of Image transfer belt / TMP sensor check mode.

SP Mode Tables

Main SP Tables-2-1

2142	[TM/ID Sensor Check Result]
005	Maximum: Front	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	With the image transfer belt / TMP sensor check mode result, take average of each 10 sampling data from TMP sensors [Front] detecting result data, and from of all sampling data, save / refresh this SP with the max. value.
006	Maximum: Center	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	With the image transfer belt / TMP sensor check mode result, take average of each 10 sampling data from TMP sensors [Center] detecting result data, and from of all sampling data, save / refresh this SP with the max. value.
007	Maximum: Rear	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	With the image transfer belt / TMP sensor check mode result, take average of each 10 sampling data from TMP sensors [Rear] detecting result data, and from of all sampling data, save / refresh this SP with the max. value.

2143	[TM/ID Sensor Check Result]
005	Minimum: Front	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	With the image transfer belt / TMP sensor check mode result, take average of each 10 sampling data from TMP sensors [Front] detecting result data, and from of all sampling data, save / refresh this SP with the min. value.
006	Minimum: Center	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	With the image transfer belt / TMP sensor check mode result, take average of each 10 sampling data from TMP sensors [Center] detecting result data, and from of all sampling data, save / refresh this SP with the min. value.
007	Minimum: Rear	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	With the image transfer belt / TMP sensor check mode result, take average of each 10 sampling data from TMP sensors [Rear] detecting result data, and from of all sampling data, save / refresh this SP with the min. value.

Main SP Tables-2-1

2144	[TM/ID Sensor Check Result]
005	Maximum 2: Front	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Saves/ refreshes this SP with the max. value of all sampling data form TMP sensor [Front] detecting result data by image transfer belt / TMP sensor check mode result.
006	Maximum 2: Center	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Saves/ refreshes this SP with the max. value of all sampling data form TMP sensor [Center] detecting result data by image transfer belt / TMP sensor check mode result.
007	Maximum 2: Rear	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Saves/ refreshes this SP with the max. value of all sampling data form TMP sensor [Rear] detecting result data by image transfer belt / TMP sensor check mode result.

2145	[TM/ID Sensor Check Result]
005	Minimum 2: Front	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Saves/ refreshes this SP with the min. value of all sampling data form TMP sensor [Front] detecting result data by image transfer belt / TMP sensor check mode result.
006	Minimum 2: Center	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Saves/ refreshes this SP with the min. value of all sampling data form TMP sensor [Center] detecting result data by image transfer belt / TMP sensor check mode result.
007	Minimum 2: Rear	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Saves/ refreshes this SP with the min. value of all sampling data form TMP sensor [Rear] detecting result data by image transfer belt / TMP sensor check mode result.

SP Mode Tables

Main SP Tables-2-1

2146

[TM-Sensor Test]

005

Number of Edge Detection:Front

*ENG

[0 to 16 / 0 / 1/step]

When the TMP sensor [Front] detecting value from the image transfer belt / TMP sensor check mode result is checked as smaller (Edge detected) as then the edge detect threshold setting value (sp2-112-020), Save / refresh this PS with the times checked so.

006

Number of Edge Detection:Center

*ENG

[0 to 16 / 0 / 1/step]

When the TMP sensor [Center] detecting value from the image transfer belt / TMP sensor check mode result is checked as smaller (Edge detected) as then the edge detect threshold setting value (sp2-112-020), Save / refresh this PS with the times checked so.

007

Number of Edge Detection:Rear

*ENG

[0 to 16 / 0 / 1/step]

When the TMP sensor [Rear] detecting value from the image transfer belt / TMP sensor check mode result is checked as smaller (Edge detected) as then the edge detect threshold setting value (sp2-112-020), Save / refresh this PS with the times checked so.

2150

[Area Mag. Correction]

Corrects main scan color scale error, deflection.

Adjusts start writing position (Register) with sub dot level.

 Value increase: image shift to the right side on the print.

 Value decrease: image shift to the left side on the print.

CMY color can be matched to adjusted BK color position by Using MUSIC after operating this SP.

027

Area 0: Bk

*ENG

[-16.00 to 16.00 / 0 / 0.01dot/step]

Main SP Tables-2-1

2150	[Area Mag. Correction]
2150	Corrects main scan color scale error, deflection. Adjusts start writing position (Register) with sub dot level.  Value increase: image stretches topically.  Value decrease: image shrinks topically. CMY color can be matched to adjusted BK color position by Using MUSIC after operating this SP.
028	Area 1: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
029	Area 2: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
030	Area 3: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
031	Area 4: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
032	Area 5: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
033	Area 6: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
034	Area 7: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
035	Area 8: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
036	Area 9: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
037	Area 10: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
038	Area 11: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
039	Area 12: Bk	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
2150	[Area Mag. Correction]
2150	Corrects main scan color scale error, deflection. Adjusts start writing position (Register) with sub dot level.  Value increase: image shift to the right side on the print.  Value decrease: image shift to the left side on the print. CMY color can be matched to adjusted BK color position by Using MUSIC after operating this SP.
079	Area 0: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]

SP Mode Tables

Main SP Tables-2-1

2150	[Area Mag. Correction]
2150	Corrects main scan color scale error, deflection. Adjusts start writing position (Register) with sub dot level.  Value increase: image stretches topically.  Value decrease: image shrinks topically. CMY color can be matched to adjusted BK color position by Using MUSIC after operating this SP.
080	Area 1: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
081	Area 2: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
082	Area 3: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
083	Area 4: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
084	Area 5: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
085	Area 6: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
086	Area 7: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
087	Area 8: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
088	Area 9: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
089	Area 10: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
090	Area 11: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
091	Area 12: Ma	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
2150	[Area Mag. Correction]
2150	Corrects main scan color scale error, deflection. Adjusts start writing position (Register) with sub dot level.  Value increase: image shift to the right side on the print.  Value decrease: image shift to the left side on the print. CMY color can be matched to adjusted BK color position by Using MUSIC after operating this SP.
131	Area 0: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]

Main SP Tables-2-1

2150	[Area Mag. Correction]
2150	Corrects main scan color scale error, deflection. Adjusts start writing position (Register) with sub dot level.  Value increase: image stretches topically.  Value decrease: image shrinks topically. CMY color can be matched to adjusted BK color position by Using MUSIC after operating this SP.
132	Area 1: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
133	Area 2: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
134	Area 3: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
135	Area 4: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
136	Area 5: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
137	Area 6: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
138	Area 7: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
139	Area 8: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
140	Area 9: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
141	Area 10: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
142	Area 11: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
143	Area 12: Cy	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
2150	[Area Mag. Correction]
2150	Corrects main scan color scale error, deflection. Adjusts start writing position (Register) with sub dot level.  Value increase: image shift to the right side on the print.  Value decrease: image shift to the left side on the print. CMY color can be matched to adjusted BK color position by Using MUSIC after operating this SP.
183	Area 0: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]

SP Mode Tables

Main SP Tables-2-1

2150	[Area Mag. Correction]
2150	Corrects main scan color scale error, deflection. Adjusts start writing position (Register) with sub dot level.  Value increase: image stretches topically.  Value decrease: image shrinks topically. CMY color can be matched to adjusted BK color position by Using MUSIC after operating this SP.
184	Area 1: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
185	Area 2: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
186	Area 3: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
187	Area 4: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
188	Area 5: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
189	Area 6: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
190	Area 7: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
191	Area 8: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
192	Area 9: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
193	Area 10: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
194	Area 11: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]
195	Area 12: Ye	*ENG	[-16.00 to 16.00 / 0 / 0.01dot/step]

2152	[Shad. Correct Setting]
2152	Changes exposure light amount.  Value increase: Light amount increases, and image density gets deeper.  Value decrease: Light amount decreases, and image density gets thinner. Except, if Process control is executed, light amount / density will change.
001	Standard Speed: Bk	*ENG	[50 to 120 / 100 / 1%/step]
002	Standard Speed: Ma	*ENG	[50 to 120 / 100 / 1%/step]
003	Standard Speed: Cy	*ENG	[50 to 120 / 100 / 1%/step]

Main SP Tables-2-1

004	Standard Speed: Ye	*ENG	[50 to 120 / 100 / 1%/step]
005	Middle Speed: Bk	*ENG	[50 to 120 / 100 / 1%/step]
006	Middle Speed: Ma	*ENG	[50 to 120 / 100 / 1%/step]
007	Middle Speed: Cy	*ENG	[50 to 120 / 100 / 1%/step]
008	Middle Speed: Ye	*ENG	[50 to 120 / 100 / 1%/step]
009	Low Speed: Bk	*ENG	[50 to 120 / 100 / 1%/step]
010	Low Speed: Ma	*ENG	[50 to 120 / 100 / 1%/step]
011	Low Speed: Cy	*ENG	[50 to 120 / 100 / 1%/step]
012	Low Speed: Ye	*ENG	[50 to 120 / 100 / 1%/step]

2154	[Shad. Correct Setting]
2154	Changes exposure light amount form each beam.  Value increase: Light amount increases, and image density gets deeper.  Value decrease: Light amount decreases, and image density gets thinner. Except, if Process control is executed, light amount / density will change. Beam interval light amount: No need to operate.
002	Front End Area: Bk: LD1	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
003	Front End Area: Bk: LD2	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
004	Front End Area: Bk: LD3	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
005	Front End Area: Bk: LD4	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
007	Front End Area: Ma: LD1	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
008	Front End Area: Ma: LD2	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
009	Front End Area: Ma: LD3	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
010	Front End Area: Ma: LD4	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
012	Front End Area: Cy: LD1	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
013	Front End Area: Cy: LD2	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
014	Front End Area: Cy: LD3	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]

SP Mode Tables

015	Front End Area: Cy: LD4	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
017	Front End Area: Ye: LD1	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
018	Front End Area: Ye: LD2	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
019	Front End Area: Ye: LD3	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
020	Front End Area: Ye: LD4	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]

015	Front End Area: Cy: LD4	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
017	Front End Area: Ye: LD1	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
018	Front End Area: Ye: LD2	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
019	Front End Area: Ye: LD3	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
020	Front End Area: Ye: LD4	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]

015	Front End Area: Cy: LD4	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
017	Front End Area: Ye: LD1	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
018	Front End Area: Ye: LD2	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
019	Front End Area: Ye: LD3	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]
020	Front End Area: Ye: LD4	*ENG	[50.0 to 150.0 / 100.0 / 0.1%/step]

2160	[Vertical Line Width]
2160	Adjusts vertical line width  Value increase: vertical line gets wider.  Value decrease: vertical line gets thinner Beware for side effects to image.
001	600dpi: Bk	*ENG	[10 to 15 / 15 / 1/step]
002	600dpi: Ma	*ENG	[10 to 15 / 15 / 1/step]
003	600dpi: Cy	*ENG	[10 to 15 / 15 / 1/step]
004	600dpi: Ye	*ENG	[10 to 15 / 15 / 1/step]
005	1200dpi: Bk	*ENG	[10 to 15 / 15 / 1/step]
006	1200dpi: Ma	*ENG	[10 to 15 / 15 / 1/step]
007	1200dpi: Cy	*ENG	[10 to 15 / 15 / 1/step]
008	1200dpi: Ye	*ENG	[10 to 15 / 15 / 1/step]
2160	[Vertical Line Width]
009	600dpi:Indet.:Bk	*ENG	[10 to 15 / 14 / 1/step]
009	Vertical line width correction: isolated dot.
010	1200dpi:Indet.:Bk	*ENG	[10 to 15 / 15 / 1/step]
010	Adjusts density for isolated dot.  Value increases: Deeper  Value decreases: Thinner Beware for side effects to image.

2160	[Vertical Line Width]
2160	Adjusts vertical line width  Value increase: vertical line gets wider.  Value decrease: vertical line gets thinner Beware for side effects to image.
001	600dpi: Bk	*ENG	[10 to 15 / 15 / 1/step]
002	600dpi: Ma	*ENG	[10 to 15 / 15 / 1/step]
003	600dpi: Cy	*ENG	[10 to 15 / 15 / 1/step]
004	600dpi: Ye	*ENG	[10 to 15 / 15 / 1/step]
005	1200dpi: Bk	*ENG	[10 to 15 / 15 / 1/step]
006	1200dpi: Ma	*ENG	[10 to 15 / 15 / 1/step]
007	1200dpi: Cy	*ENG	[10 to 15 / 15 / 1/step]
008	1200dpi: Ye	*ENG	[10 to 15 / 15 / 1/step]
2160	[Vertical Line Width]
009	600dpi:Indet.:Bk	*ENG	[10 to 15 / 14 / 1/step]
009	Vertical line width correction: isolated dot.
010	1200dpi:Indet.:Bk	*ENG	[10 to 15 / 15 / 1/step]
010	Adjusts density for isolated dot.  Value increases: Deeper  Value decreases: Thinner Beware for side effects to image.

2160	[Vertical Line Width]
2160	Adjusts vertical line width  Value increase: vertical line gets wider.  Value decrease: vertical line gets thinner Beware for side effects to image.
001	600dpi: Bk	*ENG	[10 to 15 / 15 / 1/step]
002	600dpi: Ma	*ENG	[10 to 15 / 15 / 1/step]
003	600dpi: Cy	*ENG	[10 to 15 / 15 / 1/step]
004	600dpi: Ye	*ENG	[10 to 15 / 15 / 1/step]
005	1200dpi: Bk	*ENG	[10 to 15 / 15 / 1/step]
006	1200dpi: Ma	*ENG	[10 to 15 / 15 / 1/step]
007	1200dpi: Cy	*ENG	[10 to 15 / 15 / 1/step]
008	1200dpi: Ye	*ENG	[10 to 15 / 15 / 1/step]
2160	[Vertical Line Width]
009	600dpi:Indet.:Bk	*ENG	[10 to 15 / 14 / 1/step]
009	Vertical line width correction: isolated dot.
010	1200dpi:Indet.:Bk	*ENG	[10 to 15 / 15 / 1/step]
010	Adjusts density for isolated dot.  Value increases: Deeper  Value decreases: Thinner Beware for side effects to image.

Main SP Tables-2-1

2180	[Line Pos. Adj. Clear]
001	Color Regist.	ENG	[0 or 1 / 0 / 1/step]
	Clears SP value of SP2-101-001 to 004 [Registration Correction (Main Scan)] and SP2-101-005 to 008 [Registration Correction (Sub Scan)].
002	Main Scan Length Detection	ENG	[0 or 1 / 0 / 1/step]
	Clears SP value of SP2-102-001 to 012[Magnification Adjustment].
003	MUSIC Result	ENG	[0 or 1 / 0 / 1/step]
	Clears SP value of SP2-181-003 to 082 [Line Position Adj. Result].
004	Area Magnification Correction	ENG	[0 or 1 / 0 / 1/step]
	Clears SP value of SP2-182-004 to 040 [Line Position Adj. Offset].

2181

[Line Position Adj. Result]

Values will be set from MUSIC (Auto color match) detect result. Refreshes each time executed. No need to operate.

003

Skew: M

*ENG

[-5000.000 to 5000.000 / 0.000 /

0.001um/step]

011

M. Cor.: Dot: M

*ENG

[-512 to 511 / 0 / 1dot/step]

012

M. Cor.: Subdot: M

*ENG

[-1.00 to 1.00/ 0.00 / 0.01dot/step]

013

S. Cor.: 1200 Line: Middle: M

*ENG

[-16384 to 16383 / 0 / 1line/step]

014

S. Cor.: 1200 Sub: Middle: M

*ENG

[-2.000 to 2.000 / 0.000 /

0.001line/step]

015

M. Left Mag.: Subdot: M

*ENG

[-32.00 to 32.00 / 0.00 /

0.01dot/step]

016

M. Right Mag.: Subdot: M

*ENG

[-32.00 to 32.00 / 0.00 /

0.01dot/step]

017

S. Cor.: 1200 Line: Standard: M

*ENG

[-16384 to 16383 / 0 / 1line/step]

018

S. Cor.: 1200 Sub: Standard: M

*ENG

[-2.000 to 2.000 / 0.000 /

0.001line/step]

SP Mode Tables

Main SP Tables-2-1

019

S. Cor.: 1200 Line: Low: M

*ENG

[-16384 to 16383 / 0 / 1line/step]

020

S. Cor.: 1200 Sub: Low: M

*ENG

[-2.000 to 2.000 / 0.000 /

0.001line/step]

021

Skew: C

*ENG

[-5000.000 to 5000.000 / 0.000 /

0.001um/step]

029

M. Cor.: Dot: C

*ENG

[-512 to 511 / 0 / 1dot/step]

030

M. Cor.: Subdot: C

*ENG

[-1.00 to 1.00/ 0.00 / 0.01dot/step]

031

S. Cor.: 1200 Line: Middle: C

*ENG

[-16384 to 16383 / 0 / 1line/step]

032

S. Cor.: 1200 Sub: Middle: C

*ENG

[-2.000 to 2.000 / 0.000 /

0.001line/step]

033

C. Left Mag.: Subdot: M

*ENG

[-32.00 to 32.00 / 0.00 /

0.01dot/step]

034

C. Right Mag.: Subdot: M

*ENG

[-32.00 to 32.00 / 0.00 /

0.01dot/step]

035

S. Cor.: 1200 Line: Standard: C

*ENG

[-16384 to 16383 / 0 / 1line/step]

036

S. Cor.: 1200 Sub: Standard: C

*ENG

[-2.000 to 2.000 / 0.000 /

0.001line/step]

037

S. Cor.: 1200 Line: Low: C

*ENG

[-16384 to 16383 / 0 / 1line/step]

038

S. Cor.: 1200 Sub: Low: C

*ENG

[-2.000 to 2.000 / 0.000 /

0.001line/step]

039

Skew: Y

*ENG

[-5000.000 to 5000.000 / 0.000 /

0.001um/step]

047

M. Cor.: Dot: Y

*ENG

[-512 to 511 / 0 / 1dot/step]

048

M. Cor.: Subdot: Y

*ENG

[-1.00 to 1.00 / 0.00 / 0.01dot/step]

049

S. Cor.: 1200 Line: Middle: Y

*ENG

[-16384 to 16383 / 0 / 1line/step]

050

S. Cor.: 1200 Sub: Middle: Y

*ENG

[-2.000 to 2.000 / 0.000 /

0.001line/step]

Main SP Tables-2-1

051	Y. Left Mag.: Subdot: M	*ENG	[-32.00 to 32.00 / 0.00 / 0.01dot/step]
052	Y. Right Mag.: Subdot: M	*ENG	[-32.00 to 32.00 / 0.00 / 0.01dot/step]
053	S. Cor.: 1200 Line: Standard: Y	*ENG	[-16384 to 16383 / 0 / 1line/step]
054	S. Cor.: 1200 Sub: Standard: Y	*ENG	[-2.000 to 2.000 / 0.000 / 0.001line/step]
055	S. Cor.: 1200 Line: Low: Y	*ENG	[-16384 to 16383 / 0 / 1line/step]
056	S. Cor.: 1200 Sub: Low: Y	*ENG	[-2.000 to 2.000 / 0.000 / 0.001line/step]
057	S. Cor.: 600 Sub	*ENG	[-1.000 to 1.000 / 0.000 / 0.001line/step]
059	S. Cor.: 1200 Sub :High	*ENG	[-2.000 to 2.000 / 0.000 / 0.001line/step]
060	S. Cor.: 1200 Sub :Low	*ENG	[-2.000 to 2.000 / 0.000 / 0.001line/step]
061	S. Cor.: 1200 Sub :Middle	*ENG	[-2.000 to 2.000 / 0.000 / 0.001line/step]
064	M. Cor.: Dot: K	*ENG	[-512 to 511 / 0 / 1dot/step]
072	LineSift: StandardSpeed: M	*ENG	[0 to 4 / 0 / 1line/step]
073	LineSift: LowSpeed: M	*ENG	[0 to 4 / 0 / 1line/step]
074	LineSift: StandardSpeed: C	*ENG	[0 to 4 / 0 / 1line/step]
075	LineSift: LowSpeed: C	*ENG	[0 to 4 / 0 / 1line/step]
076	LineSift: StandardSpeed: Y	*ENG	[0 to 4 / 0 / 1line/step]
077	LineSift: LowSpeed: Y	*ENG	[0 to 4 / 0 / 1line/step]
080	Detect Diff.: M	*ENG	[-1000.0 to 1000.0 / 0.0 / 0.1/step]
081	Detect Diff.: C	*ENG	[-1000.0 to 1000.0 / 0.0 / 0.1/step]
082	Detect Diff.: Y	*ENG	[-1000.0 to 1000.0 / 0.0 / 0.1/step]

SP Mode Tables

Main SP Tables-2-1

2182	[Line Position Adj. Offset]
2182	Use when color shift remains even after MUSIC. Result of MUSIC will be added to this setting value.  Value increases: image shifts towards right facing paper.  Value decreases: image shifts towards left facing paper.
004	M. Scan: Standard: Dot: M	*ENG	[-512 to 511 / 0 / 1dot/step]
005	M. Scan: Standard: Subdot: M	*ENG	[-1.00 to 1.00 / 0.0 / 0.01dot/step]
006	M. Scan: Middle: Dot: M	*ENG	[-512 to 511 / 0 / 1dot/step]
007	M. Scan: Middle: Subdot: M	*ENG	[-1.00 to 1.00 / 0.00 / 0.01dot/step]
008	M. Scan: Low: Dot: M	*ENG	[-512 to 511 / 0 / 1dot/step]
009	M. Scan: Low: Subdot: M	*ENG	[-1.00 to 1.00 / 0.00 / 0.01dot/step]
010	M. Scan: Standard: Dot: C	*ENG	[-512 to 511 / 0 / 1dot/step]
011	M. Scan: Standard: Subdot: C	*ENG	[-1.00 to 1.00 / 0.00 / 0.01dot/step]
012	M. Scan: Middle: Dot: C	*ENG	[-512 to 511 / 0 / 1dot/step]
013	M. Scan: Middle: Subdot: C	*ENG	[-1.00 to 1.00 / 0.00 / 0.01dot/step]
014	M. Scan: Low: Dot: C	*ENG	[-512 to 511 / 0 / 1dot/step]
015	M. Scan: Low: Subdot: C	*ENG	[-1.00 to 1.00 / 0.00 / 0.01dot/step]
016	M. Scan: Standard: Dot: Y	*ENG	[-512 to 511 / 0 / 1dot/step]
017	M. Scan: Standard: Subdot: Y	*ENG	[-1.00 to 1.00 / 0.00 / 0.01dot/step]
018	M. Scan: Middle: Dot: Y	*ENG	[-512 to 511 / 0 / 1dot/step]
019	M. Scan: Middle: Subdot: Y	*ENG	[-1.00 to 1.00 / 0.00 / 0.01dot/step]
020	M. Scan: Low: Dot: Y	*ENG	[-512 to 511 / 0 / 1dot/step]
021	M. Scan: Low: Subdot: Y	*ENG	[-1.00 to 1.00 / 0.00 / 0.01dot/step]

Main SP Tables-2-1

2182	[Line Position Adj. Offset]
2182	Use when color shift remains even after MUSIC. Result of MUSIC will be added to this setting value.  Value increases: image shifts towards downer facing paper.  Value decreases: image shifts towards upper facing paper.
022	S. Scan: Standard: Line: M	*ENG	[-16384 to 16383 / 0 / 1line/step]
023	S. Scan: Standard: Subline: M	*ENG	[-1.00 to 1.00 / 0.00 / 0.01line/step]
024	S. Scan: Middle: Line: M	*ENG	[-16384 to 16383 / 0 / 1line/step]
025	S. Scan: Middle: Subline: M	*ENG	[-1.00 to 1.00 / 0.00 / 0.01line/step]
026	S. Scan: Low: Line: M	*ENG	[-16384 to 16383 / 0 / 1line/step]
027	S. Scan: Low: Subline: M	*ENG	[-1.00 to 1.00 / 0.00 / 0.01line/step]
028	S. Scan: Standard: Line: C	*ENG	[-16384 to 16383 / 0 / 1line/step]
029	S. Scan: Standard: Subline: C	*ENG	[-1.00 to 1.00 / 0.00 / 0.01line/step]
030	S. Scan: Middle: Line: C	*ENG	[-16384 to 16383 / 0 / 1line/step]
031	S. Scan: Middle: Subline: C	*ENG	[-1.00 to 1.00 / 0.00 / 0.01line/step]
032	S. Scan: Low: Line: C	*ENG	[-16384 to 16383 / 0 / 1line/step]
033	S. Scan: Low: Subline: C	*ENG	[-1.00 to 1.00 / 0.00 / 0.01line/step]
034	S. Scan: Standard: Line: Y	*ENG	[-16384 to 16383 / 0 / 1line/step]
035	S. Scan: Standard: Subline: Y	*ENG	[-1.00 to 1.00 / 0.00 / 0.01line/step]
036	S. Scan: Middle: Line: Y	*ENG	[-16384 to 16383 / 0 / 1line/step]
037	S. Scan: Middle: Subline: Y	*ENG	[-1.00 to 1.00 / 0.00 / 0.01line/step]
038	S. Scan: Low: Line: Y	*ENG	[-16384 to 16383 / 0 / 1line/step]
039	S. Scan: Low: Subline: Y	*ENG	[-1.00 to 1.00 / 0.00 / 0.01line/step]

SP Mode Tables

2182

[Line Position Adj. Offset]

040

M. Scan: Dot: K

*ENG

[-512 to 511 / 0 / 1dot/step]

For setting main scan position of BK: MUSIC. No need to operate.

2182

[Line Position Adj. Offset]

040

M. Scan: Dot: K

*ENG

[-512 to 511 / 0 / 1dot/step]

For setting main scan position of BK: MUSIC. No need to operate.

2182

[Line Position Adj. Offset]

040

M. Scan: Dot: K

*ENG

[-512 to 511 / 0 / 1dot/step]

For setting main scan position of BK: MUSIC. No need to operate.

2187	[Method Select]
2187	MUSIC pattern setting. No need to operate.
002	MUSIC Pattern Length Adj.	*ENG	[-300 to 300 / 0 / 1dot/step]
003	Pattern Width Adj.	*ENG	[-512 to 511 / 0 / 1dot/step]
004	Pattern Interval Adj.	*ENG	[-512 to 511 / 0 / 1dot/step]

2187	[Method Select]
2187	MUSIC pattern setting. No need to operate.
002	MUSIC Pattern Length Adj.	*ENG	[-300 to 300 / 0 / 1dot/step]
003	Pattern Width Adj.	*ENG	[-512 to 511 / 0 / 1dot/step]
004	Pattern Interval Adj.	*ENG	[-512 to 511 / 0 / 1dot/step]

2187	[Method Select]
2187	MUSIC pattern setting. No need to operate.
002	MUSIC Pattern Length Adj.	*ENG	[-300 to 300 / 0 / 1dot/step]
003	Pattern Width Adj.	*ENG	[-512 to 511 / 0 / 1dot/step]
004	Pattern Interval Adj.	*ENG	[-512 to 511 / 0 / 1dot/step]

Main SP Tables-2-1

2190

[Line Position Adj.]

Sets belt scratch misdetection avoiding level for color shift detection. No need to operate.

012

SnSErr Range

*ENG

[0 to 3500 / 200 / 1um/step]

2193	[MUSIC Condition Set]
002	Page: Job End: BW+FC	*ENG	[0 to 999 / 500 / 1page/step]
	Condition threshold to auto execute MUSIC or not based on last printed sheets from MUSIC when finish printing in B&W+Color mode.
003	Page: Job End: FC	*ENG	[0 to 999 / 200 / 1page/step]
	Condition threshold to auto execute MUSIC or not based on last printed sheets from MUSIC when finish printing in Color mode.
004	Page: Interrupt: BW+FC	*ENG	[0 to 999 / 200 / 1page/step]
	Condition threshold to auto execute MUSIC or not based on last printed sheets from MUSIC during printing in B&W+Color mode.

Main SP Tables-2-1

005	Page: Interrupt: FC	*ENG	[0 to 999 / 200 / 1page/step]
	Condition threshold to auto execute MUSIC or not based on last printed sheets from MUSIC during printing in Color mode.
006	Page: Stand-By: BW	*ENG	[0 to 999 / 100 / 1page/step]
	Condition threshold to auto execute MUSIC or not based on last printed B&W+Color sheets from MUSIC during stand-by.
007	Page: Stand-By: FC	*ENG	[0 to 999 / 100 / 1page/step]
	Condition threshold to auto execute MUSIC or not based on last printed Color sheets from MUSIC during stand-by.
008	Temp.	*ENG	[0 to 100 / 5 / 1deg/step]
	Condition threshold to auto execute MUSIC or not based on the variation of environment temperature (Temperature and humidity sensor) since last MUSIC.
009	Time	*ENG	[1 to 1440 / 300 / 1minute/step]
	Condition threshold to auto execute MUSIC on recover from energy save mode / Power on or not based on the elapsed time since last MUSIC.
010	Magnification	*ENG	[0.00 to 1.00 / 0.10 / 0.01%/step]
011	Temp. 2	*ENG	[0 to 100 / 5 / 1deg/step]
	Condition threshold (Threshold revel: Mid.) to auto execute MUSIC or not based on the variation of internal temperature (drum temp. sensor) since last MUSIC.
012	Time 2	*ENG	[1 to 9999 / 600 / 1minute/step]
013	Temp. 3	*ENG	[0 to 100 / 10 / 1deg/step]
	Condition threshold (Threshold revel: Hi.) to auto execute MUSIC or not based on the variation of internal temperature (drum temp. sensor) since last MUSIC.
016	Page: Power ON:BW+FC	*ENG	[0 to 999 / 200 / 1page/step]
	Condition threshold to auto execute MUSIC on recover from energy save mode / Power on or not based sheets printed during electrification.

SP Mode Tables

Main SP Tables-2-1

2194	[MUSIC Execution Result]
001	Year	*ENG	[0 to 99 / 0 / 1year/step]
	Saves / Refreshes this SP with “Year” of last MUSIC.
002	Month	*ENG	[1 to 12 / 1 / 1month/step]
	Saves / Refreshes this SP with “Month” of last MUSIC.
003	Day	*ENG	[1 to 31 / 1 / 1day/step]
	Saves / Refreshes this SP with “Day” of last MUSIC.
004	Hour	*ENG	[0 to 23 / 0 / 1hour/step]
	Saves / Refreshes this SP with “Hour” of last MUSIC.
005	Minute	*ENG	[0 to 59 / 0 / 1minute/step]
	Saves / Refreshes this SP with “Minute” of last MUSIC.
006	Temperature	*ENG	[0 to 100 / 0 / 1deg/step]
	Saves / Refreshes this SP with “temperature” (temperature and humidity sensor) of last MUSIC.
007	Execution Result	*ENG	[0 or 1 / 0 / 1/step] 0: Success 1: Failure
008	Number of Execution	*ENG	[0 to 999999 / 0 / 1time/step]
	Saves / Refreshes this SP with the total count of MUSIC done since machine shipped.
009	Number of Failure	*ENG	[0 to 999999 / 0 / 1time/step]
	Saves / Refreshes this SP with the total count of MUSIC failed since machine shipped.
010	Error Result: C	*ENG	[0 to 9 / 0 / 1/step]
	Saves / Refreshes this SP with the Cyan result among the MUSIC execution result.

Main SP Tables-2-1

011	Error Result: M	*ENG	[0 to 9 / 0 / 1/step]
	Saves / Refreshes this SP with the Magenta result among the MUSIC execution result.
012	Error Result: Y	*ENG	[0 to 9 / 0 / 1/step]
	Saves / Refreshes this SP with the yellow result among the MUSIC execution result.
013	Error Result: K	*ENG	[0 to 9 / 0 / 1/step]
	Saves / Refreshes this SP with the Black result among the MUSIC execution result.
014	Temperature 2	*ENG	[-10 to 100 / 0 / 1deg/step]
	Saves / Refreshes this SP with the internal temperature (drum temp. sensor) of last MUSIC.

2195	[Realtime MUSIC Condition Set]
001	ON/OFF	*ENG	[0 or 1 / 1 / 1/step] 0: OFF 1: ON
	Sets whether to have real time MUSIC ON (1) or OFF (0).
002	Page: Interrupt: BW+FC	*ENG	[0 to 999 / 50 / 1page/step]
	Condition threshold to auto execute real time MUSIC based on the sheets printed with last MUSIC during printing in B&W+Color.
003	Page: Interrupt: FC	*ENG	[0 to 999 / 50 / 1page/step]
	Condition threshold to auto execute real time MUSIC based on the sheets printed with last MUSIC during printing in Color.
004	Temperature 4	*ENG	[0 to 100 / 1 / 1deg/step]
	Condition threshold (Threshold revel: Mid.) to auto execute real time MUSIC or not based on the variation of internal temperature (drum temp. sensor) since last MUSIC.

SP Mode Tables

005

Temperature 5

*ENG

[0 to 100 / 1 / 1deg/step]

Condition threshold (Threshold revel: Hi.) to auto execute real time MUSIC or not based on the variation of internal temperature (drum temp. sensor) since last MUSIC.

005

Temperature 5

*ENG

[0 to 100 / 1 / 1deg/step]

Condition threshold (Threshold revel: Hi.) to auto execute real time MUSIC or not based on the variation of internal temperature (drum temp. sensor) since last MUSIC.

005

Temperature 5

*ENG

[0 to 100 / 1 / 1deg/step]

Condition threshold (Threshold revel: Hi.) to auto execute real time MUSIC or not based on the variation of internal temperature (drum temp. sensor) since last MUSIC.

2197	[MUSIC Start Time]
001	MUSIC Start Time (EDT)	*ENG	[10 to 40 / 20 / 10ms/step]
	Sets margin time for starting scan to set starting position of scan MUSIC pattern accurately.
002	TM Sensor Position	*ENG	[50.0 to 500.0 / 165.0 / 0.1mm/step]
	Sets physical distance information of TMP Sensor to set MUSIC pattern scanning start position accurately.

2197	[MUSIC Start Time]
001	MUSIC Start Time (EDT)	*ENG	[10 to 40 / 20 / 10ms/step]
	Sets margin time for starting scan to set starting position of scan MUSIC pattern accurately.
002	TM Sensor Position	*ENG	[50.0 to 500.0 / 165.0 / 0.1mm/step]
	Sets physical distance information of TMP Sensor to set MUSIC pattern scanning start position accurately.

2197	[MUSIC Start Time]
001	MUSIC Start Time (EDT)	*ENG	[10 to 40 / 20 / 10ms/step]
	Sets margin time for starting scan to set starting position of scan MUSIC pattern accurately.
002	TM Sensor Position	*ENG	[50.0 to 500.0 / 165.0 / 0.1mm/step]
	Sets physical distance information of TMP Sensor to set MUSIC pattern scanning start position accurately.

Main SP Tables-2-1

2220	[Skew Origin Set]
	-
001	M: Skew Motor	ENG	[0 or 1 / 0 / -]
	M: skew original setting.
002	C: Skew Motor	ENG	[0 or 1 / 0 / -]
	C: skew original setting.
003	Y: Skew Motor	ENG	[0 or 1 / 0 / -]
	Y: skew original setting.

Main SP Tables-2-1

2221	[LD Power: Fixed]
2221	Decides output setting value as the value set to this SP when not controlling Process control.
001	K	*ENG	[0 to 200 / 100 / 1%/step]
002	C	*ENG
003	M	*ENG
004	Y	*ENG

2229	[Develop DC Vias]
001	Standard Speed: Bk	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set. (Std. speed: Bk)
002	Standard Speed: C	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set. (Std. speed: C)
003	Standard Speed: M	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set. (Std. speed: M)
004	Standard Speed: Y	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set. (Std. speed: Y)
005	Middle Speed Bk	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set.
006	Middle Speed C	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set.

SP Mode Tables

Main SP Tables-2-1

007	Middle Speed M	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set.
008	Middle Speed Y	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set.
009	Low Speed: Bk	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set.
010	Low Speed: C	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set. (Low speed: C)
011	Low Speed: M	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set. (Low speed: M)
012	Low Speed: Y	*ENG	[0 to 800 / 550 / 1-V/step]
	Refers to develop bias set to this SP when electric potential control with Process control is not set. (Low speed: Y)

2230	[QL Power Setting]
001	Standard Speed	*ENG	[0 to 0 / 0 / 1%/step]
	Decides light amount to remove electricity at Std. speed.
002	Middle Speed	*ENG	[0 to 0 / 0 / 1%/step]
	Decides light amount to remove electricity at Mid. Speed.
003	Low Speed	*ENG	[0 to 0 / 0 / 1%/step]
	Decides light amount to remove electricity at Low. Speed.

Main SP Tables-2-1

2241	[Temperature/Humidity: Display]
003	Exec Interval: Extra Fan Control	*ENG	[1 to 3600 / 10 / 1sec/step]
	Sets interval time for temperature detection to decide whether to extend control.
004	AIT Temperature	ENG	[0.0 to 70.0 / 0.0 / 0.1deg/step]
	Displays imaging temperature.

2242	[TS Operation Env. Log]
001	TS<=40	ENG	[0 to 99999999 / 0 / 1mm/step]
	TS: imaging temperature (Celsius): developing with each temperature division U: displays Bk rotation distance.
002	40<TS<=45	ENG	[0 to 99999999 / 0 / 1mm/step]
	TS: imaging temperature (Celsius): developing with each temperature division U: displays Bk rotation distance.
003	45<TS	ENG	[0 to 99999999 / 0 / 1mm/step]
	TS: imaging temperature (Celsius): developing with each temperature division U: displays Bk rotation distance.
004	Log Clear	ENG	[0 or 1 / 0 / 1/step]
	Clears image temperature usage environment log.

SP Mode Tables

Main SP Tables-2-1

2302

[Environmental Correction:Trans]

001

Current Environmental Display

ENG

[0 to 0 / 0 / 0/step]

Displays current environment division of transfer.

002

Forced Setting

*ENG

[0 to 6 / 0 / 1/step]

0: Sensor detect

1: LL

2: ML

3: MM

4: HM

5: HH

6: SLL

Force sets current environment division of transfer.

003

Absolute Humidity:Threshold 1

*ENG

[0.00 to 100.00 / 4.00 /

0.01g/m3/step]

Sets environment division threshold (LL/ML)

004

Absolute Humidity:Threshold 2

*ENG

[0.00 to 100.00 / 8.00 /

0.01g/m3/step]

Sets environment division threshold (ML/MM)

005

Absolute Humidity:Threshold 3

*ENG

[0.00 to 100.00 / 16.00 /

0.01g/m3/step]

Sets environment division threshold (MM/HM)

006

Absolute Humidity:Threshold 4

*ENG

[0.00 to 100.00 / 24.00 /

0.01g/m3/step]

Sets environment division threshold (HM/HH)

007

Temperature:Threshold

*ENG

[-5 to 30 / 5 / 1deg/step]

Sets absolute temperature threshold (SLL)

Main SP Tables-2-1

2303	[Time-Lapse Correction]
001	Current Div K	*ENG	[0 to 3 / 0 / 1/step]
	Displays the current time-lapse division
002	Current Div C	*ENG	[0 to 3 / 0 / 1/step]
	Displays the current time-lapse division
003	Current Div M	*ENG	[0 to 3 / 0 / 1/step]
	Displays the current time-lapse division
004	Current Div Y	*ENG	[0 to 3 / 0 / 1/step]
	Displays the current time-lapse division
005	Correction Threshold 1_Bk	*ENG	[0 to 600000 / 5000 / 10page/step]
	Sets time-lapse correction threshold.
006	Correction Threshold 1_Color	*ENG	[0 to 600000 / 5000 / 10page/step]
	Sets time-lapse correction threshold.
007	Correction Threshold 2_Bk	*ENG	[0 to 600000 / 20000 / 10page/step]
	Sets time-lapse correction threshold.
008	Correction Threshold 2_Color	*ENG	[0 to 600000 / 20000 / 10page/step]
	Sets time-lapse correction threshold.
009	Correction Threshold 3_Bk	*ENG	[0 to 600000 / 50000 / 10page/step]
	Sets time-lapse correction threshold.
010	Correction Threshold 3_Color	*ENG	[0 to 600000 / 50000 / 10page/step]
	Sets time-lapse correction threshold.

2308

[Paper Size Correction]

Sets paper width threshold for paper size correction.

001

Threshold 1

*ENG

[0 to 350 / 297 / 1mm/step]

SP Mode Tables

Main SP Tables-2-1

002	Threshold 2	*ENG	[0 to 350 / 257 / 1mm/step]
003	Threshold 3	*ENG	[0 to 350 / 210 / 1mm/step]
004	Threshold 4	*ENG	[0 to 350 / 148 / 1mm/step]
2308	[Paper Size Correction]
2308	Sets paper width threshold for paper size correction (when using optional roller.).
005	Threshold 1	*ENG	[0 to 350 / 297 / 1mm/step]
006	Threshold 2	*ENG	[0 to 350 / 257 / 1mm/step]
007	Threshold 3	*ENG	[0 to 350 / 210 / 1mm/step]
008	Threshold 4	*ENG	[0 to 350 / 148 / 1mm/step]

2311	[Non Image Area:Bias]
	Sets bias for non image area.
001	Image Transfer	*ENG	[10 to 250 / 100 / 5%/step]
002	Paper Transfer	*ENG	[0 to 230 / 0 / 1-uA/step]
	* When between papers are close.
003	Paper Transfer	*ENG	[0 to 2100 / 500 / 10V/step]

2316

[Power ON:Bias]

Sets bias for non image area.

001

Image Transfer

*ENG

[0 to 80 / 5 / 1uA/step]

2326	[Transfer Roller CL:Bias]
2326	Sets CL bias for corresponding operation.
001	Positive:befor and after JOB	*ENG	[0 to 2100 / 250 / 10V/step]
002	Negative:befor and after JOB	*ENG	[10 to 995 / 100 / 10%/step]

Main SP Tables-2-1

003

Positive:befor and afterProcon

*ENG

[0 to 2100 / 2000 / 10V/step]

004

Negative:befor and afterProcon

*ENG

[10 to 995 / 100 / 10%/step]

005

Positive:prevention

*ENG

[0 to 2100 / 500 / 10V/step]

2351	[Common:BW:Bias]
2351	Sets image transfer output value per line speed in BW mode.
001	Image Transfer:standard	*ENG	[0 to 80 / D146: 33, D147: 33, D148: 41, D149: 57, D150: 57 / 1uA/step]
002	Image Transfer:Middle	*ENG	[0 to 80 / 24 / 1uA/step]
003	Image Transfer:low	*ENG	[0 to 80 / 16 / 1uA/step]

2357

[Common:FC:Bias]

Sets image transfer output value per line speed in FC mode.

001

ImageTransfer:standard:Bk

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / D146: 33,

D147: 33, D148: 41, D149: 57,

D150: 57 / 1uA/step]

002

ImageTransfer:standard:C

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / D146: 33,

D147: 33, D148: 41, D149: 57,

D150: 57 / 1uA/step]

003

ImageTransfer:standard:M

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / D146: 35,

D147: 35, D148: 45, D149: 62,

D150: 62 / 1uA/step]

004

ImageTransfer:standard:Y

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / D146: 38,

D147: 38, D148: 49, D149: 67,

D150: 67 / 1uA/step]

SP Mode Tables

Main SP Tables-2-1

005

ImageTransfer:Middle:Bk

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / 24 /

1uA/step]

006

ImageTransfer:Middle:C

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / 24 /

1uA/step]

007

ImageTransfer:Middle:M

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / 26 /

1uA/step]

008

ImageTransfer:Middle:Y

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / 28 /

1uA/step]

009

Image Transfer:low:Bk

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / 16 /

1uA/step]

010

Image Transfer:low:C

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / 16 /

1uA/step]

011

Image Transfer:low:M

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / 18 /

1uA/step]

012

Image Transfer:low:Y

*ENG

[0 to (D146: 60, D147: 60, D148:

80, D149: 80, D150: 80) / 19 /

1uA/step]

2360	[Common:BW:Env.CorrectionTable]
2360	Sets image transfer output environment correction table per line speed in BW mode.
001	Image Transfer:standard	*ENG	[1 to 100 / 2 / 1/step]
002	Image Transfer:Middle	*ENG	[1 to 100 / 2 / 1/step]
003	Image Transfer:low	*ENG	[1 to 100 / 2 / 1/step]

Main SP Tables-2-1

2360	[Common:FC:Env.CorrectionTable]
2360	Sets image transfer output environment correction table per line speed in FC mode.
004	ImageTransfer:standard:Bk	*ENG	[1 to 100 / 1 / 1/step]
005	ImageTransfer:standard:C	*ENG	[1 to 100 / 2 / 1/step]
006	ImageTransfer:standard:M	*ENG	[1 to 100 / 3 / 1/step]
007	ImageTransfer:standard:Y	*ENG	[1 to 100 / 4 / 1/step]
008	ImageTransfer:Middle:Bk	*ENG	[1 to 100 / 1 / 1/step]
009	ImageTransfer:Middle:C	*ENG	[1 to 100 / 2 / 1/step]
010	ImageTransfer:Middle:M	*ENG	[1 to 100 / 3 / 1/step]
011	ImageTransfer:Middle:Y	*ENG	[1 to 100 / 4 / 1/step]
012	Image Transfer:low:Bk	*ENG	[1 to 100 / 1 / 1/step]
013	Image Transfer:low:C	*ENG	[1 to 100 / 2 / 1/step]
014	Image Transfer:low:M	*ENG	[1 to 100 / 3 / 1/step]
015	Image Transfer:low:Y	*ENG	[1 to 100 / 4 / 1/step]

2361	[Time-Lapse Correction: Div 1]
2361	Input table number of time-lapse correction.
001	Standard Speed: Bk	*ENG	[1 to 60 / 2 / 1/step]
002	Mid Speed: Bk	ENG
003	Low Speed: Bk	ENG
004	Standard Speed: FC: K	*ENG	[1 to 60 / 1 / 1/step]
005	Standard Speed: FC: C	*ENG
006	Standard Speed: FC: M	*ENG
007	Standard Speed: FC: Y	*ENG
008	Mid Speed: FC: K	ENG

SP Mode Tables

Main SP Tables-2-1

009	Mid Speed: FC: C	ENG
010	Mid Speed: FC: M	ENG
011	Mid Speed: FC: Y	ENG
012	Low Speed: FC: K	ENG
013	Low Speed: FC: C	ENG
014	Low Speed: FC: M	ENG
015	Low Speed: FC: Y	ENG

2362	[Time-Lapse Correction: Div 2]
2362	Input table number of time-lapse correction.
001	Standard Speed: Bk	*ENG	[1 to 60 / 3 / 1/step]
002	Mid Speed: Bk	ENG
003	Low Speed: Bk	ENG
004	Standard Speed: FC: K	*ENG	[1 to 60 / 1 / 1/step]
005	Standard Speed: FC: C	*ENG
006	Standard Speed: FC: M	*ENG
007	Standard Speed: FC: Y	*ENG
008	Mid Speed: FC: K	ENG
009	Mid Speed: FC: C	ENG
010	Mid Speed: FC: M	ENG
011	Mid Speed: FC: Y	ENG
012	Low Speed: FC: K	ENG
013	Low Speed: FC: C	ENG
014	Low Speed: FC: M	ENG
015	Low Speed: FC: Y	ENG

Main SP Tables-2-1

2363	[Time-Lapse Correction: Div 3]
2363	Input table number of time-lapse correction.
001	Standard Speed: Bk	*ENG	[1 to 60 / 4 / 1/step]
002	Mid Speed: Bk	ENG
003	Low Speed: Bk	ENG
004	Standard Speed: FC: K	*ENG	[1 to 60 / 1 / 1/step]
005	Standard Speed: FC: C	*ENG
006	Standard Speed: FC: M	*ENG
007	Standard Speed: FC: Y	*ENG
008	Mid Speed: FC: K	ENG
009	Mid Speed: FC: C	ENG
010	Mid Speed: FC: M	ENG
011	Mid Speed: FC: Y	ENG
012	Low Speed: FC: K	ENG
013	Low Speed: FC: C	ENG
014	Low Speed: FC: M	ENG
015	Low Speed: FC: Y	ENG

2400	[Paper Transfer Roller Settings]
001	Width of Paper Transfer Roller	*ENG	[0 or 1 / 0 / 1/step] 0: Default roller 1: Wide roller
	Width of Paper Transfer Roller
002	Detatch timing in waiting	*ENG	[0 to 600 / 240 / 1min/step]
	Detach timing in waiting

SP Mode Tables

Main SP Tables-2-1

2403

[Plain1:Bias:BW]

Sets paper transfer ampere per paper thickness / mode (FC/BW) / line speed / printing sides.

001

PaperTransfer:standard:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 22, D147: 22, D148: 28,

D149: 38, D150: 38 / 1-uA/step]

002

PaperTransfer:standard:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 22, D147: 22, D148: 28,

D149: 38, D150: 38 / 1-uA/step]

003

PaperTransfer:low:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 11 /

1-uA/step]

004

PaperTransfer:low:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 11 /

1-uA/step]

2407

[Plain1:Bias:FC]

Sets paper transfer ampere per paper thickness / mode (FC/BW) / line speed / printing sides.

001

PaperTransfer:standard:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 29, D147: 29, D148: 36,

D149: 50, D150: 50 / 1-uA/step]

002

PaperTransfer:standard:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 29, D147: 29, D148: 36,

D149: 50, D150: 50 / 1-uA/step]

003

PaperTransfer:low:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 14 /

1-uA/step]

Main SP Tables-2-1

004

PaperTransfer:low:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 14 /

1-uA/step]

2411	[Plain1:SizeCorrection:BW]
2411	Sets paper transfer ampere per paper thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 100 / 1%/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 105 / 1%/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 100 / 1%/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 105 / 1%/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 105 / 1%/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 118 / 1%/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 105 / 1%/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 118 / 1%/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 118 / 1%/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 131 / 1%/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 118 / 1%/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 131 / 1%/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 132 / 1%/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 184 / 1%/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 132 / 1%/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 184 / 1%/step]

SP Mode Tables

Main SP Tables-2-1

2411	[Plain1:SizeCorrection:BW]
2411	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides. (When using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 100 / 1%/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 105 / 1%/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 100 / 1%/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 105 / 1%/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 105 / 1%/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 118 / 1%/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 105 / 1%/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 118 / 1%/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 118 / 1%/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 131 / 1%/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 118 / 1%/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 131 / 1%/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 132 / 1%/step]

Main SP Tables-2-1

038

Wide Roller:PaperTransfer:Standard:2Sid:S5

*ENG

[100 to 995 / 184 / 1%/step]

039

Wide Roller:PaperTransfer:Low:1Side:S5

*ENG

[100 to 995 / 132 / 1%/step]

040

Wide Roller:PaperTransfer:Low:2Side:S5

*ENG

[100 to 995 / 184 / 1%/step]

2412	[Plain1:SizeCorrection:FC]
2412	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 120 / 1%/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 140 / 1%/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 120 / 1%/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 140 / 1%/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 118 / 1%/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 180 / 1%/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 118 / 1%/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 180 / 1%/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 130 / 1%/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 200 / 1%/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 130 / 1%/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 200 / 1%/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 140 / 1%/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 240 / 1%/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 140 / 1%/step]

SP Mode Tables

Main SP Tables-2-1

020	PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 240 / 1%/step]
2412	[Plain1:SizeCorrection:FC]
2412	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides. (When using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 120 / 1%/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 140 / 1%/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 120 / 1%/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 140 / 1%/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 118 / 1%/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 180 / 1%/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 118 / 1%/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 180 / 1%/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 130 / 1%/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 200 / 1%/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 130 / 1%/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 200 / 1%/step]

Main SP Tables-2-1

037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 140 / 1%/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 240 / 1%/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 140 / 1%/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 240 / 1%/step]

2413	[Plain1:Size-Env.Correct:BW]
2413	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 10 / 1/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 15 / 1/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 10 / 1/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 15 / 1/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 11 / 1/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 16 / 1/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 11 / 1/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 16 / 1/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 12 / 1/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 17 / 1/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 12 / 1/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 17 / 1/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 13 / 1/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 18 / 1/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 13 / 1/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 18 / 1/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 14 / 1/step]

SP Mode Tables

Main SP Tables-2-1

018	PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 19 / 1/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 14 / 1/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 19 / 1/step]
2413	[Plain1:Size-Env.Correct:BW]
2413	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides. (When using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 10 / 1/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 15 / 1/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 10 / 1/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 15 / 1/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 11 / 1/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 16 / 1/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 11 / 1/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 16 / 1/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 12 / 1/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 17 / 1/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 12 / 1/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 17 / 1/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 13 / 1/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 18 / 1/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 13 / 1/step]

Main SP Tables-2-1

036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 18 / 1/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 14 / 1/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 19 / 1/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 14 / 1/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 19 / 1/step]

2414	[Plain1:Size-Env.Correct:FC]
2414	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 20 / 1/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 25 / 1/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 20 / 1/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 25 / 1/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 21 / 1/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 26 / 1/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 21 / 1/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 26 / 1/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 22 / 1/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 27 / 1/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 22 / 1/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 27 / 1/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 23 / 1/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 28 / 1/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 23 / 1/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 28 / 1/step]

SP Mode Tables

Main SP Tables-2-1

017	PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 24 / 1/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 29 / 1/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 24 / 1/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 29 / 1/step]
2414	[Plain1:Size-Env.Correct:FC]
2414	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides. (When using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 20 / 1/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 25 / 1/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 20 / 1/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 25 / 1/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 21 / 1/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 26 / 1/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 21 / 1/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 26 / 1/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 22 / 1/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 27 / 1/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 22 / 1/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 27 / 1/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 23 / 1/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 28 / 1/step]

Main SP Tables-2-1

035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 23 / 1/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 28 / 1/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 24 / 1/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 29 / 1/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 24 / 1/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 29 / 1/step]

2415	[Plain1:LeadingEdgeCorrection]
2415	Sets output value [%] for paper transfer ampere leading edge correction per paper thickness / line speed / printing sides.
001	PaperTransfer:Standard:1Side	*ENG	[0 to 995 / 100 / 5%/step]
002	PaperTransfer:Standard:2Side	*ENG	[0 to 995 / 100 / 5%/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 995 / 100 / 5%/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 995 / 100 / 5%/step]

2416	[Plain1:SwitchTimingLeadEdge]
2416	Sets output value [%] for paper transfer ampere leading edge correction per paper thickness / line speed / printing sides.
001	PaperTransfer:Standard:1side	*ENG	[0 to 50 / 0 / 2mm/step]
002	PaperTransfer:Standard:2side	*ENG	[0 to 50 / 0 / 2mm/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 50 / 0 / 2mm/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 50 / 0 / 2mm/step]

2417

[Plain1:TrailEdgeCorrection]

Sets output value [%] for paper transfer ampere leading edge correction per paper thickness / line speed / printing sides.

SP Mode Tables

001	PaperTransfer:Standard:1Side	*ENG	[0 to 995 / 100 / 5%/step]
002	PaperTransfer:Standard:2Side	*ENG	[0 to 995 / 100 / 5%/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 995 / 100 / 5%/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 995 / 100 / 5%/step]

001	PaperTransfer:Standard:1Side	*ENG	[0 to 995 / 100 / 5%/step]
002	PaperTransfer:Standard:2Side	*ENG	[0 to 995 / 100 / 5%/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 995 / 100 / 5%/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 995 / 100 / 5%/step]

001	PaperTransfer:Standard:1Side	*ENG	[0 to 995 / 100 / 5%/step]
002	PaperTransfer:Standard:2Side	*ENG	[0 to 995 / 100 / 5%/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 995 / 100 / 5%/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 995 / 100 / 5%/step]

2418	[Plain1:SwitchTimingTrailEdge]
2418	Sets switch timing for paper transfer ampere trailing edge correction of paper thickness / line speed / printing sides.
001	PaperTransfer:Standard:1side	*ENG	[0 to 50 / 0 / 2mm/step]
002	PaperTransfer:Standard:2side	*ENG	[0 to 50 / 0 / 2mm/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 50 / 0 / 2mm/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 50 / 0 / 2mm/step]

2418	[Plain1:SwitchTimingTrailEdge]
2418	Sets switch timing for paper transfer ampere trailing edge correction of paper thickness / line speed / printing sides.
001	PaperTransfer:Standard:1side	*ENG	[0 to 50 / 0 / 2mm/step]
002	PaperTransfer:Standard:2side	*ENG	[0 to 50 / 0 / 2mm/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 50 / 0 / 2mm/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 50 / 0 / 2mm/step]

2418	[Plain1:SwitchTimingTrailEdge]
2418	Sets switch timing for paper transfer ampere trailing edge correction of paper thickness / line speed / printing sides.
001	PaperTransfer:Standard:1side	*ENG	[0 to 50 / 0 / 2mm/step]
002	PaperTransfer:Standard:2side	*ENG	[0 to 50 / 0 / 2mm/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 50 / 0 / 2mm/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 50 / 0 / 2mm/step]

Main SP Tables-2-1

2423

[Plain2:Bias:BW]

Sets paper transfer ampere per paper thickness / mode (FC/BW) / line speed / printing sides.

001

PaperTransfer:standard:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 22, D147: 22, D148: 28,

D149: 38, D150: 38 / 1-uA/step]

002

PaperTransfer:standard:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 22, D147: 22, D148: 28,

D149: 38, D150: 38 / 1-uA/step]

003

PaperTransfer:low:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 11 /

1-uA/step]

004

PaperTransfer:low:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 11 /

1-uA/step]

Main SP Tables-2-1

2425	[Hhsmall:LeadEdgeCorrection]
2425	*Un used
001	PaperTransfer:1side	*ENG	[0 to 995 / 100 / 5%/step]
002	PaperTransfer:2stSid	*ENG	[0 to 995 / 100 / 5%/step]

2427

[Plain2:Bias:FC]

Sets paper transfer ampere per paper thickness / mode (FC/BW) / line speed / printing sides.

001

PaperTransfer:standard:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 29, D147: 29, D148: 36,

D149: 50, D150: 50 / 1-uA/step]

002

PaperTransfer:standard:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 29, D147: 29, D148: 36,

D149: 50, D150: 50 / 1-uA/step]

003

PaperTransfer:low:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 14 /

1-uA/step]

004

PaperTransfer:low:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 14 /

1-uA/step]

2431	[Plain2:SizeCorrection:BW]
2431	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]

SP Mode Tables

Main SP Tables-2-1

005	PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 100 / 1%/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 105 / 1%/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 100 / 1%/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 105 / 1%/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 105 / 1%/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 118 / 1%/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 105 / 1%/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 118 / 1%/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 118 / 1%/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 131 / 1%/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 118 / 1%/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 131 / 1%/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 132 / 1%/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 184 / 1%/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 132 / 1%/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 184 / 1%/step]
2431	[Plain2:SizeCorrection:BW]
2431	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 100 / 1%/step]

Main SP Tables-2-1

026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 105 / 1%/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 100 / 1%/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 105 / 1%/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 105 / 1%/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 118 / 1%/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 105 / 1%/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 118 / 1%/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 118 / 1%/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 131 / 1%/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 118 / 1%/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 131 / 1%/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 132 / 1%/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 184 / 1%/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 132 / 1%/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 184 / 1%/step]

2432	[Plain2:SizeCorrection:FC]
2432	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]

SP Mode Tables

Main SP Tables-2-1

004	PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 120 / 1%/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 140 / 1%/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 120 / 1%/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 140 / 1%/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 118 / 1%/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 180 / 1%/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 118 / 1%/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 180 / 1%/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 130 / 1%/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 200 / 1%/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 130 / 1%/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 200 / 1%/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 140 / 1%/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 240 / 1%/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 140 / 1%/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 240 / 1%/step]
2432	[Plain2:SizeCorrection:FC]
2432	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]

Main SP Tables-2-1

025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 120 / 1%/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 140 / 1%/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 120 / 1%/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 140 / 1%/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 118 / 1%/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 180 / 1%/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 118 / 1%/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 180 / 1%/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 130 / 1%/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 200 / 1%/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 130 / 1%/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 200 / 1%/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 140 / 1%/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 240 / 1%/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 140 / 1%/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 240 / 1%/step]

2433

[Plain2:Size-Env.Correct:BW]

Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides.

001

PaperTransfer:Standard:1Sid:S1

*ENG

[1 to 100 / 10 / 1/step]

SP Mode Tables

Main SP Tables-2-1

002	PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 15 / 1/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 10 / 1/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 15 / 1/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 11 / 1/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 16 / 1/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 11 / 1/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 16 / 1/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 12 / 1/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 17 / 1/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 12 / 1/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 17 / 1/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 13 / 1/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 18 / 1/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 13 / 1/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 18 / 1/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 14 / 1/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 19 / 1/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 14 / 1/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 19 / 1/step]
2433	[Plain2:Size-Env.Correct:BW]
2433	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 10 / 1/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 15 / 1/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 10 / 1/step]

Main SP Tables-2-1

024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 15 / 1/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 11 / 1/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 16 / 1/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 11 / 1/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 16 / 1/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 12 / 1/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 17 / 1/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 12 / 1/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 17 / 1/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 13 / 1/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 18 / 1/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 13 / 1/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 18 / 1/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 14 / 1/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 19 / 1/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 14 / 1/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 19 / 1/step]

2434

[Plain2:Size-Env.Correct:FC]

Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides.

SP Mode Tables

Main SP Tables-2-1

001	PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 20 / 1/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 25 / 1/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 20 / 1/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 25 / 1/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 21 / 1/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 26 / 1/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 21 / 1/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 26 / 1/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 22 / 1/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 27 / 1/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 22 / 1/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 27 / 1/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 23 / 1/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 28 / 1/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 23 / 1/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 28 / 1/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 24 / 1/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 29 / 1/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 24 / 1/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 29 / 1/step]
2434	[Plain2:Size-Env.Correct:FC]
2434	Sets paper transfer ampere paper size correction per paper thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 20 / 1/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 25 / 1/step]

Main SP Tables-2-1

023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 20 / 1/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 25 / 1/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 21 / 1/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 26 / 1/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 21 / 1/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 26 / 1/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 22 / 1/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 27 / 1/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 22 / 1/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 27 / 1/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 23 / 1/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 28 / 1/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 23 / 1/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 28 / 1/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 24 / 1/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 29 / 1/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 24 / 1/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 29 / 1/step]

SP Mode Tables

Main SP Tables-2-1

2435	[Plain2:LeadingEdgeCorrection]
2435	Sets output value [%] for paper transfer leading edge correction per paper thickness / line speed / printing sides.
001	PaperTransfer:Standard:1Side	*ENG	[0 to 995 / 100 / 5%/step]
002	PaperTransfer:Standard:2Side	*ENG	[0 to 995 / 100 / 5%/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 995 / 100 / 5%/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 995 / 100 / 5%/step]

2436	[Plain2:SwitchTimingLeadEdge]
2436	Sets switch timing for paper transfer ampere leading edge correct per thickness / line speed / printing sides.
001	PaperTransfer:Standard:1side	*ENG	[0 to 50 / 0 / 2mm/step]
002	PaperTransfer:Standard:2side	*ENG	[0 to 50 / 0 / 2mm/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 50 / 0 / 2mm/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 50 / 0 / 2mm/step]

2437	[Plain2:TrailEdgeCorrection]
2437	Sets output value [%] for paper transfer trailing edge correction per paper thickness / line speed / printing sides.
001	PaperTransfer:Standard:1Side	*ENG	[0 to 995 / 100 / 5%/step]
002	PaperTransfer:Standard:2Side	*ENG	[0 to 995 / 100 / 5%/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 995 / 100 / 5%/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 995 / 100 / 5%/step]

Main SP Tables-2-1

2438	[Plain2:SwitchTimingTrailEdge]
2438	Sets switch timing for paper transfer ampere trailing edge correct per thickness / line speed / printing sides.
001	PaperTransfer:Standard:1side	*ENG	[0 to 50 / 0 / 2mm/step]
002	PaperTransfer:Standard:2side	*ENG	[0 to 50 / 0 / 2mm/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 50 / 0 / 2mm/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 50 / 0 / 2mm/step]

2443

[Middle:Bias:BW]

Sets paper transfer ampere per thickness / mode (FC/BW) / line speed / printing sides.

001

PaperTransfer:standard:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 22, D147: 22, D148: 28,

D149: 38, D150: 38 / 1-uA/step]

002

PaperTransfer:standard:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 22, D147: 22, D148: 28,

D149: 38, D150: 38 / 1-uA/step]

003

PaperTransfer:low:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 11 /

1-uA/step]

004

PaperTransfer:low:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 11 /

1-uA/step]

SP Mode Tables

Main SP Tables-2-1

2447

[Middle:Bias:FC]

Sets paper transfer ampere per thickness / mode (FC/BW) / line speed / printing sides.

001

PaperTransfer:standard:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 29, D147: 29, D148: 36,

D149: 50, D150: 50 / 1-uA/step]

002

PaperTransfer:standard:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 30, D147: 30, D148: 39,

D149: 53, D150: 53 / 1-uA/step]

003

PaperTransfer:low:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 14 /

1-uA/step]

004

PaperTransfer:low:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 15 /

1-uA/step]

2451	[Middle:SizeCorrection:BW]
2451	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 100 / 1%/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 106 / 1%/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 100 / 1%/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 106 / 1%/step]

Main SP Tables-2-1

009	PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 105 / 1%/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 110 / 1%/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 105 / 1%/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 110 / 1%/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 113 / 1%/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 120 / 1%/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 113 / 1%/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 120 / 1%/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 118 / 1%/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 140 / 1%/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 118 / 1%/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 140 / 1%/step]
2451	[Middle:SizeCorrection:BW]
2451	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 100 / 1%/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 106 / 1%/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 100 / 1%/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 106 / 1%/step]

SP Mode Tables

Main SP Tables-2-1

029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 105 / 1%/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 110 / 1%/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 105 / 1%/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 110 / 1%/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 113 / 1%/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 120 / 1%/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 113 / 1%/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 120 / 1%/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 118 / 1%/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 140 / 1%/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 118 / 1%/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 140 / 1%/step]

2452	[Middle:SizeCorrection:FC]
2452	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 106 / 1%/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 132 / 1%/step]

Main SP Tables-2-1

007	PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 106 / 1%/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 132 / 1%/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 110 / 1%/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 170 / 1%/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 110 / 1%/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 170 / 1%/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 120 / 1%/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 189 / 1%/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 120 / 1%/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 189 / 1%/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 140 / 1%/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 245 / 1%/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 140 / 1%/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 245 / 1%/step]
2452	[Middle:SizeCorrection:FC]
2452	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 106 / 1%/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 132 / 1%/step]

SP Mode Tables

Main SP Tables-2-1

027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 106 / 1%/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 132 / 1%/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 110 / 1%/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 170 / 1%/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 110 / 1%/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 170 / 1%/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 120 / 1%/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 189 / 1%/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 120 / 1%/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 189 / 1%/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 140 / 1%/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 245 / 1%/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 140 / 1%/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 245 / 1%/step]

2453	[Middle:Size-Env.Correct:BW]
2453	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 10 / 1/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 41 / 1/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 10 / 1/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 41 / 1/step]

Main SP Tables-2-1

005	PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 39 / 1/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 42 / 1/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 39 / 1/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 42 / 1/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 40 / 1/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 43 / 1/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 40 / 1/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 43 / 1/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 40 / 1/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 44 / 1/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 40 / 1/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 44 / 1/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 40 / 1/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 45 / 1/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 40 / 1/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 45 / 1/step]
2453	[Middle:Size-Env.Correct:BW]
2453	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 10 / 1/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 41 / 1/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 10 / 1/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 41 / 1/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 39 / 1/step]

SP Mode Tables

Main SP Tables-2-1

026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 42 / 1/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 39 / 1/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 42 / 1/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 40 / 1/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 43 / 1/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 40 / 1/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 43 / 1/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 40 / 1/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 44 / 1/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 40 / 1/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 44 / 1/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 40 / 1/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 45 / 1/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 40 / 1/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 45 / 1/step]

2454	[Middle:Size-Env.Correct:FC]
2454	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 20 / 1/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 49 / 1/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 20 / 1/step]

Main SP Tables-2-1

004	PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 49 / 1/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 46 / 1/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 50 / 1/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 46 / 1/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 50 / 1/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 47 / 1/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 51 / 1/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 47 / 1/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 51 / 1/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 48 / 1/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 52 / 1/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 48 / 1/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 52 / 1/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 48 / 1/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 53 / 1/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 48 / 1/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 53 / 1/step]
2454	[Middle:Size-Env.Correct:FC]
2454	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 20 / 1/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 49 / 1/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 20 / 1/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 49 / 1/step]

SP Mode Tables

Main SP Tables-2-1

025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 46 / 1/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 50 / 1/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 46 / 1/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 50 / 1/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 47 / 1/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 51 / 1/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 47 / 1/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 51 / 1/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 48 / 1/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 52 / 1/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 48 / 1/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 52 / 1/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 48 / 1/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 53 / 1/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 48 / 1/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 53 / 1/step]

2455

[Middle:LeadingEdgeCorrection]

Sets output value [%] for paper transfer ampere leading edge correction per thickness / line speed / printing sides.

001

PaperTransfer:Standard:1Side

*ENG

[0 to 995 / 100 / 5%/step]

Main SP Tables-2-1

002	PaperTransfer:Standard:2Side	*ENG	[0 to 995 / 100 / 5%/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 995 / 100 / 5%/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 995 / 100 / 5%/step]

2456	[Middle:SwitchTimingLeadEdge]
2456	Sets switch timing for paper transfer ampere leading edge correction per thickness / line speed / printing sides.
001	PaperTransfer:Standard:1side	*ENG	[0 to 50 / 0 / 2mm/step]
002	PaperTransfer:Standard:2side	*ENG	[0 to 50 / 0 / 2mm/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 50 / 0 / 2mm/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 50 / 0 / 2mm/step]

2457	[Middle:TrailEdgeCorrection]
2457	Sets output value [%] for paper transfer ampere trailing edge correction per thickness / line speed / printing sides.
001	PaperTransfer:Standard:1Side	*ENG	[0 to 995 / 100 / 5%/step]
002	PaperTransfer:Standard:2Side	*ENG	[0 to 995 / 100 / 5%/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 995 / 100 / 5%/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 995 / 100 / 5%/step]

2458	[Middle:SwitchTimingTrailEdge]
2458	Sets switch timing for paper transfer ampere trailing edge correction per thickness / line speed / printing sides.
001	PaperTransfer:Standard:1side	*ENG	[0 to 50 / 0 / 2mm/step]
002	PaperTransfer:Standard:2side	*ENG	[0 to 50 / 0 / 2mm/step]
003	Paper Transfer:Low:1side	*ENG	[0 to 50 / 0 / 2mm/step]
004	Paper Transfer:Low:2side	*ENG	[0 to 50 / 0 / 2mm/step]

SP Mode Tables

Main SP Tables-2-1

2463

[Thin:Bias:BW]

Sets paper transfer ampere per thickness / mode (FC/BW) / line speed / printing sides.

001

PaperTransfer:Standard:1Sid

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 22, D147: 22, D148: 28,

D149: 38, D150: 38 / 1-uA/step]

002

PaperTransfer:Standard:2Sid

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 22, D147: 22, D148: 28,

D149: 38, D150: 38 / 1-uA/step]

003

Paper Transfer:Low:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 11 /

1-uA/step]

004

Paper Transfer:Low:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 11 /

1-uA/step]

2467

[Thin:Bias:FC]

Sets paper transfer ampere per thickness / mode (FC/BW) / line speed / printing sides.

001

PaperTransfer:Standard:1Sid

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 29, D147: 29, D148: 36,

D149: 50, D150: 50 / 1-uA/step]

002

PaperTransfer:Standard:2Sid

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) /

D146: 29, D147: 29, D148: 36,

D149: 50, D150: 50 / 1-uA/step]

003

Paper Transfer:Low:1side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 14 /

1-uA/step]

Main SP Tables-2-1

004

Paper Transfer:Low:2side

*ENG

[0 to (D146: 200, D147: 200, D148:

250, D149: 250, D150: 250) / 14 /

1-uA/step]

2471	[Thin:SizeCorrection:BW]
2471	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
002	PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
004	PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 100 / 1%/step]
006	PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 105 / 1%/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 100 / 1%/step]
008	PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 105 / 1%/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 111 / 1%/step]
010	PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 140 / 1%/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 111 / 1%/step]
012	PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 140 / 1%/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 121 / 1%/step]
014	PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 175 / 1%/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 121 / 1%/step]
016	PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 175 / 1%/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 132 / 1%/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 211 / 1%/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 132 / 1%/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 211 / 1%/step]

SP Mode Tables

Main SP Tables-2-1

2471	[Thin:SizeCorrection:BW]
2471	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 100 / 1%/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 105 / 1%/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 100 / 1%/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 105 / 1%/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 111 / 1%/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 140 / 1%/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 111 / 1%/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 140 / 1%/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 121 / 1%/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 175 / 1%/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 121 / 1%/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 175 / 1%/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 132 / 1%/step]

Main SP Tables-2-1

038

Wide Roller:PaperTransfer:Standard:2Sid:S5

*ENG

[100 to 995 / 211 / 1%/step]

039

Wide Roller:PaperTransfer:Low:1Side:S5

*ENG

[100 to 995 / 132 / 1%/step]

040

Wide Roller:PaperTransfer:Low:2Side:S5

*ENG

[100 to 995 / 211 / 1%/step]

2472	[Thin:SizeCorrection:FC]
2472	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
002	PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
004	PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 106 / 1%/step]
006	PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 130 / 1%/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 106 / 1%/step]
008	PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 130 / 1%/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 117 / 1%/step]
010	PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 153 / 1%/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 117 / 1%/step]
012	PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 153 / 1%/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 128 / 1%/step]
014	PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 177 / 1%/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 128 / 1%/step]
016	PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 177 / 1%/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 140 / 1%/step]
018	PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 200 / 1%/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 140 / 1%/step]

SP Mode Tables

Main SP Tables-2-1

020	PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 200 / 1%/step]
2472	[Thin:SizeCorrection:FC]
2472	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[100 to 995 / 100 / 1%/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[100 to 995 / 100 / 1%/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[100 to 995 / 106 / 1%/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[100 to 995 / 130 / 1%/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[100 to 995 / 106 / 1%/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[100 to 995 / 130 / 1%/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[100 to 995 / 117 / 1%/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[100 to 995 / 153 / 1%/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[100 to 995 / 117 / 1%/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[100 to 995 / 153 / 1%/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[100 to 995 / 128 / 1%/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[100 to 995 / 177 / 1%/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[100 to 995 / 128 / 1%/step]
036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[100 to 995 / 177 / 1%/step]

Main SP Tables-2-1

037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[100 to 995 / 140 / 1%/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[100 to 995 / 200 / 1%/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[100 to 995 / 140 / 1%/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[100 to 995 / 200 / 1%/step]

2473	[Thin:Size-Env.Correct:BW]
2473	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides.
001	PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 10 / 1/step]
002	PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 15 / 1/step]
003	PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 10 / 1/step]
004	PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 15 / 1/step]
005	PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 11 / 1/step]
006	PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 16 / 1/step]
007	PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 11 / 1/step]
008	PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 16 / 1/step]
009	PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 12 / 1/step]
010	PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 30 / 1/step]
011	PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 12 / 1/step]
012	PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 30 / 1/step]
013	PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 13 / 1/step]
014	PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 31 / 1/step]
015	PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 13 / 1/step]
016	PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 31 / 1/step]
017	PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 14 / 1/step]

SP Mode Tables

Main SP Tables-2-1

018	PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 32 / 1/step]
019	PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 14 / 1/step]
020	PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 32 / 1/step]
2473	[Thin:Size-Env.Correct:BW]
2473	Sets paper transfer ampere paper size correction per thickness / mode (FC/BW) / line speed / printing sides. (With using optional wide unit)
021	Wide Roller:PaperTransfer:Standard:1Sid:S1	*ENG	[1 to 100 / 10 / 1/step]
022	Wide Roller:PaperTransfer:Standard:2Sid:S1	*ENG	[1 to 100 / 15 / 1/step]
023	Wide Roller:PaperTransfer:Low:1Side:S1	*ENG	[1 to 100 / 10 / 1/step]
024	Wide Roller:PaperTransfer:Low:2Side:S1	*ENG	[1 to 100 / 15 / 1/step]
025	Wide Roller:PaperTransfer:Standard:1Sid:S2	*ENG	[1 to 100 / 11 / 1/step]
026	Wide Roller:PaperTransfer:Standard:2Sid:S2	*ENG	[1 to 100 / 16 / 1/step]
027	Wide Roller:PaperTransfer:Low:1Side:S2	*ENG	[1 to 100 / 11 / 1/step]
028	Wide Roller:PaperTransfer:Low:2Side:S2	*ENG	[1 to 100 / 16 / 1/step]
029	Wide Roller:PaperTransfer:Standard:1Sid:S3	*ENG	[1 to 100 / 12 / 1/step]
030	Wide Roller:PaperTransfer:Standard:2Sid:S3	*ENG	[1 to 100 / 30 / 1/step]
031	Wide Roller:PaperTransfer:Low:1Side:S3	*ENG	[1 to 100 / 12 / 1/step]
032	Wide Roller:PaperTransfer:Low:2Side:S3	*ENG	[1 to 100 / 30 / 1/step]
033	Wide Roller:PaperTransfer:Standard:1Sid:S4	*ENG	[1 to 100 / 13 / 1/step]
034	Wide Roller:PaperTransfer:Standard:2Sid:S4	*ENG	[1 to 100 / 31 / 1/step]
035	Wide Roller:PaperTransfer:Low:1Side:S4	*ENG	[1 to 100 / 13 / 1/step]

Main SP Tables-2-1

036	Wide Roller:PaperTransfer:Low:2Side:S4	*ENG	[1 to 100 / 31 / 1/step]
037	Wide Roller:PaperTransfer:Standard:1Sid:S5	*ENG	[1 to 100 / 14 / 1/step]
038	Wide Roller:PaperTransfer:Standard:2Sid:S5	*ENG	[1 to 100 / 32 / 1/step]
039	Wide Roller:PaperTransfer:Low:1Side:S5	*ENG	[1 to 100 / 14 / 1/step]
040	Wide Roller:PaperTransfer:Low:2Side:S5	*ENG	[1 to 100 / 32 / 1/step]

SP2-005 TO 2-473 (DRUM)

HOME PAGE |

< Previous | Contents | Next >