1001

[Leading Edge Registration]

Adjust the image position against the transfer paper by adjusting timing of start registration. Reflects adjustment values with no change.

“+” is the direction from which images come out. (Makes the registration start fast.)

“-“ is the direction which images disappear. (Makes the registration start slow.)

001

Tray: Thin

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

002

Tray: Plain

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

003

Tray: Mid-thick

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

004

Tray: Thick 1

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

005

Tray: Thick 2

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

006

Tray: Thick 3

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

007

Tray: Thick 4

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

008

By-pass: Thin

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

009

By-pass: Plain

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

010

By-pass: Mid-thick

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

011

By-pass: Thick 1

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

012

By-pass: Thick 2

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

013

By-pass: Thick 3

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

014

By-pass: Thick 4

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

015

Duplex: Thin

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

016

Duplex: Plain

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

017

Duplex: Mid-thick

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

018

Duplex: Thick 1

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

019

Duplex: Thick 2

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

020

Duplex: Thick 3

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

021

Tray: Thin:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

022

Tray: Plain:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

023

Tray: Mid-thick:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

024

Tray: Thick 1:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

025

Tray: Thick 2:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

026

Tray: Thick 3:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

027

Tray: Thick 4:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

028

By-pass: Thin:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

029

By-pass: Plain:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

030

By-pass: Mid-thick:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

031

By-pass: Thick 1:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

032

By-pass: Thick 2:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

033

By-pass: Thick 3:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

034

By-pass: Thick 4:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

035

Duplex: Thin:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

036

Duplex: Plain:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

037

Duplex: Mid-thick:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

038

Duplex: Thick 1:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

039

Duplex: Thick 2:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

040

Duplex: Thick 3:1200

*ENG

[-9.0 to 9.0 / 0.0 / 0.1mm/step]

1002

[Side-to-Side Registration]

Adjust image position against the transfer paper by adjusting start position for writing. Reflects adjustment values with no change.

“+” is the direction to which images shift. (Trimming area in the left increases.) “-“ is the direction to which images shift. (Trimming area in the left decreases.)

001

By-pass Tray

ENG

[-4.0 to 4.0 / 0.0 / 0.1mm/step]

002

Paper Tray 1

ENG

003

Paper Tray 2

ENG

004

Paper Tray 3

ENG

005

Paper Tray 4

ENG

006

Duplex

*ENG

[-4.0 to 4.0 / 0.0 / 0.1mm/step]

007

Large Capacity Tray

*ENG

[-4.0 to 4.0 / 0.0 / 0.1mm/step]

1003

[Paper Buckle]

001

Paper Tray1: Thin

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

002

Paper Tray1: Plain

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

003

Paper Tray 1: Mid-thick

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

004

Paper Tray1: Thick1

*ENG

[-4.0 to 5.0 / -2.0 / 0.1mm/step]

005

Tray2/3/4/5/LCT: Thin

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

006

Tray2/3/4/5/LCT: Plain

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

007

Tray 2/3/4/5/LCT: Mid-thick

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

008

Tray2/3/4/5/LCT: Thick 1

*ENG

[-4.0 to 5.0 / -2.0 / 0.1mm/step]

009

By-pass: Thin

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

010

By-pass: Plain

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

011

By-pass: Mid-thick

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

012

By-pass:Thick1

*ENG

[-4.0 to 5.0 / -1.0 / 0.1mm/step]

013

Duplex:Thin

*ENG

[-4.0 to 5.0 / -1.5 / 0.1mm/step]

014

Duplex:Plain

*ENG

[-4.0 to 5.0 / -1.5 / 0.1mm/step]

015

Duplex: Mid-thick

*ENG

[-4.0 to 5.0 / -1.5 / 0.1mm/step]

016

Duplex:Thick1

*ENG

[-4.0 to 5.0 / -1.5 / 0.1mm/step]

017

Paper Tray1: Thin:1200

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

018

Paper Tray1: Plain:1200

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

019

Paper Tray 1: Mid-thick:1200

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

020

Paper Tray1: Thick1:1200

*ENG

[-4.0 to 5.0 / -2.0 / 0.1mm/step]

021

Tray2/3/4/5/LCT: Thin:1200

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

022

Tray2/3/4/5/LCT: Plain:1200

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

023

Tray2/3/4/5/LCT: Mid:1200

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

024

Tray2/3/4/5/LCT: Thick 1:1200

*ENG

[-4.0 to 5.0 / -2.0 / 0.1mm/step]

025

By-pass: Thin:1200

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

026

By-pass: Plain:1200

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

027

By-pass: Mid-thick:1200

*ENG

[-4.0 to 5.0 / 0.0 / 0.1mm/step]

028

By-pass:Thick1:1200

*ENG

[-4.0 to 5.0 / -1.0 / 0.1mm/step]

029

Duplex:Thin:1200

*ENG

[-4.0 to 5.0 / -1.5 / 0.1mm/step]

030

Duplex:Plain:1200

*ENG

[-4.0 to 5.0 / -1.5 / 0.1mm/step]

031

Duplex: Mid-thick:1200

*ENG

[-4.0 to 5.0 / -1.5 / 0.1mm/step]

032

Duplex:Thick1:1200

*ENG

[-4.0 to 5.0 / -1.5 / 0.1mm/step]

1007

[By-Pass Size Detection]

-

001

Switch LT SEF/LG SEF

ENG

[0 or 1 / 0 / 1/step] 0:OFF

1:ON

Select either LT SEF or LG SEF to detect preferentially when using bypass tray which can not auto detect size.

002

By-Pass Jam Detection Set

ENG

[0 or 1 / 0 / 1/step]

0: Normal Detection

1: Simple Detection

Special order function for old models: When receiving long length FAX, enter max. size of custom size for when setting receiving in bypass size, prevent from jamming shorter data than that. 0: Normal detect : when paper size is different form set size (longer of shorter), jam. 1: Simple detect: Jam when paper size is longer than set size.

1008

[SI By-Pass Size Detection Adj]

-

001

Sidefence Auto Adj

*ENG

[0 or 1 / 1 / 1/step]

0: OFF

1: ON

With one action bypass models, switches do or do not side fence auto fine tune when paper is set. But when setting auto fine tune off, detectable paper size will drop to same as regular bypass tray.

003

Paper Set Fix Time

*ENG

[0 to 10 / 2 / 1sec/step]

Set the waiting time to activate the side fence auto adjustment after a stack of paper has been set on the by-pass tray. Will have more time till side fence to star moving when setting waiting time longer, but time for setting paper will also be loner. If waiting time is short, side fence might star to move during setting paper. SC or malfunction or so will not occur.

004

Sidefence Contact Detction:Timeout Adj Value

*ENG

[-200 to 4000 /

0 / 100msec/step]

With one action bypass tray, displays an alert message when side fence and paper are more then 10mm apart due to not able to auto adjust. Adjust that distance. Plus make movable distance longer.

005

Sidefence Adj Correction Value

*ENG

[0.00 to 4.00 /

0.00 / 0.01mm/step]

Fine tunes the distance of paper and side fence for one action bypass tray. Plus makes more distance.

006

Sidefence F adj1

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Side fence of one action bypass: enter value of front sensor touched down (papers exist).

007

Sidefence F adj2

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Side fence of one action bypass: enter value of front sensor free (paper doesn't exist).

008

Sidefence R adj1

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Side fence of one action bypass: enter value of rear sensor touched down (papers exist).

009

Sidefence R adj2

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Side fence of one action bypass: enter value of rear sensor free (paper doesn't exist).

010

Envelope Choukei 4_SEF/Postcard_SEF Th

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

011

Envelope Choukei 3_SEF/B6_SEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

012

B6_SEF/HLT_SEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

013

HLT_SEF/A5_SEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

014

A5_SEF/(C6/Envelope Youkei 2)_LEF,B5_SEF Th

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

015

(C6/Envelope Youkei 2)_LEF/Monarch_LEF Th

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

016

Monarch_LEF/(F/GL)_SEF,DoublePostcard_LEF Th

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

017

(F/GL)_SEF,DoublePostc_LEF/A5_LEF,LT_SEF Th

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

018

A5_LEF/DL Env_LEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

019

LT_SEF/SRA4_SEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

020

DL Env_LEF/C5_LEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

021

SRA4_SEF/Envelope Youchou 3_LEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

022

C5_LEF/COM10_LEF,Env Kaku 2_SEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

023

(EvYouc3,COM10)LEF,EvKa2SEF/10x14SEF,B5LEFTh

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

024

10 x 14_SEF/Exe_LEF, 8K_SEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

025

Exe_LEF, 8K_SEF/DLT_SEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

026

DLT_SEF/A3_SEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

027

A3_SEF/12 x 18_SEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

028

12 x 18_SEF/SRA3_SEF Threshold

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

029

Switch Env Youchou 3 LEF/Env Youkei 4 LEF

*ENG

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

030

Switch LT SEF/LG SEF

*ENG

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

031

Switch C5 LEF/SRA4

*ENG

[0 or 1 / 0 / 1/step]

0: OFF

1: ON

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

032

Main Scan Size Adj

ENG

[0 or 1 / 0 / 1/step]

Fine tunes side fence position sensor of one action bypass tray.

033

Main Scan Size Adj Result (0:Fail 1:Succeed)

ENG

[0 or 1 / 0 / 1/step]

Displays result of fine tuning side fence position sensor of one action bypass tray.

034

Paper Press Amt Adj Value

*ENG

[-1.6 to 3.0 /

0.0 / 0.1mm/step]

Have pressuring time for side fence of one action bypass tray (for truing up the paper) When making this value larger than necessary, side effects might occur like thin paper buckling.

035

Postcard_SEF/Envelope Choukei 3_SEF Th

*ENG

[0.000 to 3.300

/ 0.000 /

0.001V/step]

Adjoining paper width threshold with side fence position sensor of one action bypass tray.

1009

[Initial Operation Setting]

Switches 1: ON 0: OFF of register back rush removal when recovering form sleep mode. With default setting, this is OFF prior less noise.

001

Registration Gear Backlash Cut

*ENG

[0 or 1 / 0 / 1/step] 0:OFF

1:ON

1101

[Reload Permit Setting]

001

Pre-rotation Start Temp.

*ENG

[0 to 200 / 0 / 1deg/step]

Do not change. Temperature for when to switch form no rotate heating to stand up heating.

002

Reload Target Temp.:Center

*ENG

[0 to 190 / D146:123, D147:123, D148:141, D149:157, D150:157 /

1deg/step]

Do not change. Reload permission target temperature: center

003

Reload Target Temp.:Press

*ENG

[0 to 200 / D146:120, D147:120, D148:150, D149:148, D150:148 /

1deg/step]

Do not change. Reload permission target temperature: pressure

004

Temp.:Delta:Cold:Center

*ENG

[0 to 200 / D146:31, D147:31, D148:33, D149:32, D150:32 /

1deg/step]

Do not change. Difference value from reload permission target value: cold: center

005

Temp.:Delta:Cold:End

*ENG

[0 to 200 / D146:31, D147:31, D148:33, D149:32, D150:32 /

1deg/step]

Do not change. Reload permission temperature: difference: cold: edge

006

Temp.:Delta:Cold:Press

*ENG

[0 to 200 / D146:110, D147:110, D148:110, D149:90, D150:90 /

1deg/step]

Do not change. Difference value from reload permission target value: cold: pressure

007

Forced Reload Time:Cold

*ENG

[0.0 to 100.0 /

D146: 4.9, D147:

4.9, D148: 5.0,

D149: 6.1, D150:

6.1 / 0.1sec/step]

Do not change. Force reload time when cold

008

Temp.:Delta:Low Power:Center

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Difference value from reload permission target value: warm: center

009

Temp.:Delta:Low Power:End

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Reload permission temperature: difference: warm: edge

010

Temp.:Delta:Low Power:Press

*ENG

[0 to 200 / D146:110, D147:110, D148:110, D149:90, D150:90 /

1deg/step]

Do not change. Difference value from reload permission target value: warm: pressure

011

Forced Reload Time:Low Power

*ENG

[0.0 to 100.0 /

D146: 49, D147:

49, D148: 50,

D149: 61, D150:

61 / 0.1sec/step]

Do not change. Force reload time when warm

012

Temp.:Delta:Hot:Center

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Difference value from reload permission target value: hot: center

013

Temp.:Delta:Hot:End

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Reload permission temperature: difference: hot: edge

014

Temp.:Delta:Hot:Press

*ENG

[0 to 200 / D146:110, D147:110, D148:110, D149:90, D150:90 /

1deg/step]

Do not change. Difference value from reload permission target value: hot: pressure

015

Forced Reload Time:Hot

*ENG

[0.0 to 100.0 /

D146: 4.9, D147:

4.9, D148: 5.0,

D149: 6.1, D150:

6.1 / 0.1sec/step]

Do not change. Force reload time when hot

016

Temp.:Delta:Cold:BW1/2:Center

*ENG

[0 to 200 / D146:31, D147:31, D148:33, D149:32, D150:32 /

1deg/step]

Do not change. Difference value from reload permission target value: cold BW: center

017

Temp.:Delta:Cold:BW1/2:End

*ENG

[0 to 200 / D146:31, D147:31, D148:33, D149:32, D150:32 /

1deg/step]

Do not change. Difference value from reload permission target value: cold BW: edge

018

Temp.:Delta:Cold:BW1/2:Press

*ENG

[0 to 200 / D146:110, D147:110, D148:110, D149:90, D150:90 /

1deg/step]

Do not change. Difference value from reload permission target value: cold BW: pressure

019

Forced Reload Time:Cold:BW1/2

*ENG

[0.0 to 100.0 / D146:42, D147:42, D148:50, D149:61, D150:61 /

0.1sec/step]

Do not change. Force reload time when cold BW

101

Reload Target Temp.:Center:Energy Saving

*ENG

[0 to 200 / D146:

115, D147: 115,

D148: 125, D149:

127, D150: 127 /

1deg/step]

Do not change. Reload permission target temperature: center BW2

102

Reload Target Temp.:Press:Energy Saving

*ENG

[0 to 200 / D146:120, D147:120, D148:120, D149:100, D150:100 /

1deg/step]

Do not change. Reload permission target temperature: pressure BW2

103

Temp.:Delta:Cold:Energy Saving:Center

*ENG

[0 to 200 / 40 / 1deg/step]

Do not change. Reload permission temperature: difference: cold: center

104

Temp.:Delta:Cold:Energy Saving:End

*ENG

[0 to 200 / 100 / 1deg/step]

Do not change. Reload permission temperature: difference: cold BW2: edge

105

Temp.:Delta:Cold:Energy Saving:Press

*ENG

[0 to 200 / 70 / 1deg/step]

Do not change. Reload permission temperature: difference: cold BW2: edge

106

Forced Reload Time:Cold:Energy Saving

*ENG

[0.0 to 100.0 / D146:300, D147:300, D148:200, D149:340, D150:340 /

0.1sec/step]

Do not change. Force reload time when cold BW2

151

Temp.:Delta:Low Temp.:Center

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Difference value from reload permission target value: low temp: center

152

Temp.:Delta:Low Temp.:End

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Reload permission temperature: difference: low temp: edge

153

Temp.:Delta:Low Temp.:Press

*ENG

[0 to 200 / D146, D147:70, D148(NA, TW): 40, D148(EU, AS,

CHN, KOR): 35, D149, D150: 33 /

1deg/step]

Do not change. Difference value from reload permission target value: low temp: pressure

154

Forced Reload Time:Low Temp.

*ENG

[0.0 to 100.0 /

60.0 / 0.1sec/step]

Do not change. Force reload time when low temp.

201

Temp.:Delta:Cold:Center:FIN-less/ADF-less

*ENG

[0 to 200 / D146:31, D147:31, D148:33, D149:32, D150:32 /

1deg/step]

Do not change. Reload permission temperature: difference: cold center: No FIN/No ADF

202

Temp.:Delta:Cold:End:FIN-less/ADF-less

*ENG

[0 to 200 / D146:31, D147:31, D148:33, D149:32, D150:32 /

1deg/step]

Do not change. Reload permission temperature: difference: cold edge: No FIN/No ADF

203

Temp.:Delta:Cold:Press:FIN-less/ADF-less

*ENG

[0 to 200 / D146:110, D147:110, D148:110, D149:90, D150:90 /

1deg/step]

Do not change. Reload permission temperature: difference: cold pressure: No FIN/No ADF

204

Forced Reload Time:Cold:FIN-less/ADF-less

*ENG

[0.0 to 100.0 /

D146:4.9,

D147:4.9,

D148:5.0,

D149:6.1, D150:6.1 /

0.1sec/step]

Do not change. Reload permission force reload time: cold: No FIN/No ADF

211

Temp:Delta:Cold:Center:FIN-less/ADF-attached

*ENG

[0 to 200 / D146:31, D147:31, D148:33, D149:32, D150:32 /

1deg/step]

Do not change. Reload permission temperature: difference: cold center: No FIN/With ADF

212

Temp.:Delta:Cold:End:FIN-less/ADF-attached

*ENG

[0 to 200 / D146:31, D147:31, D148:33, D149:32, D150:32 /

1deg/step]

Do not change. Reload permission temperature: difference: cold edge: No FIN/With ADF

213

Temp.:Delta:Cold:Press:FIN-less/ADF-attached

*ENG

[0 to 200 / D146:110, D147:110, D148:110, D149:90, D150:90 /

1deg/step]

Do not change. Reload permission temperature: difference: cold pressure: No FIN/With ADF

[0.0 to 100.0 /

D146:4.9,

D147:4.9,

ForcedReloadTime:Cold:FIN-less/ADF-attached

*ENG

D148:5.0,

214

D149:6.1,

D150:6.1 /

0.1sec/step]

Do not change. Reload permission force reload time: cold: No FIN/With ADF

1102

[Feed Permit Setting]

001

Temp.:Lower Delta:Center

*ENG

[0 to 200 / D146:40, D147:40, D148:52, D149:40, D150:40 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : center

002

Temp.:Lower Delta:End

*ENG

[0 to 200 / D146:40, D147:40, D148:52, D149:40, D150:40 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : edge

003

Temp.:Upper Delta:Center

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : center

004

Temp.:Upper Delta:End

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : edge

005

Temp.:Lower Delta:Press

*ENG

[0 to 200 / D146, 147: 90, D148(NA, TW): 80, D148(EU, AS, CHN, KOR): 83, D149 and D150(NA, TW): 95, D149 and D150(EU, AS, CHN, KOR): 100 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure

006

Rotation Time

*ENG

[0 to 100 / 0 / 1sec/step]

Do not change. Paper feed start permission temp. : before decision rotate time

007

Temp.:Lower Delta:Center:Sp.1

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : center: special mode 1

008

Temp.:Lower Delta:End:Sp.1

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : edge: special mode 1

009

Temp.:Upper Delta:Center:Sp.1

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : center: special mode 1

010

Temp.:Upper Delta:End:Sp.1

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : edge: special mode 1

011

Temp.:Lower Delta:Press:Sp.1

*ENG

[0 to 200 / D146:45, D147:45, D148:5, D149:5, D150:5 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure: special mode 1

012

Rotation Time:Sp.1

*ENG

[0 to 100 / 0 / 1sec/step]

Do not change. Paper feed permission setting rotate before decision time: special mode 1

013

Temp.:Lower Delta:Center:Sp.2

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : center: special mode 2

014

Temp.:Lower Delta:End:Sp.2

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : edge: special mode 2

015

Temp.:Upper Delta:Center:Sp.2

*ENG

[0 to 200 / 15 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : center: special mode 2

016

Temp.:Upper Delta:End:Sp.2

*ENG

[0 to 200 / 15 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : edge: special mode 2

017

Temp.:Lower Delta:Press:Sp.2

*ENG

[0 to 200 / 100 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure: special mode 2

018

Rotation Time:Sp2

*ENG

[0 to 100 / 0 / 1sec/step]

Do not change. Paper feed permission setting rotate before decision time: special mode 2

019

Feed Permit Time

*ENG

[0 to 100 / 60 / 1sec/step]

Do not change. Setting time between Before paper feed action form paper feed permission.

020

Temp.:Lower Delta:Center

*ENG

[0 to 200 / D146:40, D147:40, D148:52, D149:40, D150:40 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : center

021

Temp.:Lower Delta:End

*ENG

[0 to 200 / D146:40, D147:40, D148:52, D149:40, D150:40 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : edge

022

Temp.:Upper Delta:Center

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : center

023

Temp.:Upper Delta:End

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : edge

024

Temp.:Lower Delta:Press

*ENG

[0 to 200 / D146:26, D147:26, D148:8, D149:17, D150:17 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure

025

Temp.:Lower Delta:Press

*ENG

[0 to 200 / D146:43, D147:43, D148:25, D149:34, D150:34 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure

026

Rotation Time

*ENG

[0 to 100 / 0 / 1sec/step]

Do not change. Paper feed start permission temp. : before decision rotate time

027

Temp.:Lower Delta:Center

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : center

028

Temp.:Lower Delta:End

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : edge

029

Temp.:Upper Delta:Center

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : center

030

Temp.:Upper Delta:End

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : edge

031

Temp.:Lower Delta:Press

*ENG

[0 to 200 / D146:11, D147:11, D148:5, D149:11, D150:11 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure

032

Temp.:Lower Delta:Press

*ENG

[0 to 200 / D146:28, D147:28, D148:22, D149:28, D150:28 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure

033

Rotation Time

*ENG

[0 to 100 / 0 / 1sec/step]

Do not change. Paper feed start permission temp. : before decision rotate time

034

Temp.:Lower Delta:Center

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : center

035

Temp.:Lower Delta:End

*ENG

[0 to 200 / 5 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : edge

036

Temp.:Upper Delta:Center

*ENG

[0 to 200 / 15 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : center

037

Temp.:Upper Delta:End

*ENG

[0 to 200 / 15 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : edge

038

Temp.:Lower Delta:Press

*ENG

[0 to 200 / 100 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure

039

Temp.:Lower Delta:Press

*ENG

[0 to 200 / 15 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure

040

Rotation Time

*ENG

[0 to 100 / 0 / 1sec/step]

Do not change. Paper feed start permission temp. : before decision rotate time

041

Judgment Power A

*ENG

[0 to 2000 / D146(NA, TW): 1405, D146(EU, AS, CHN, KOR): 1515, D147(NA, TW): 1400, D147(EU, AS, CHN, KOR):1510, D148(NA, TW): 1355, D148(EU, AS, CHN, KOR): 1615, D149(NA, TW): 1315, D149(EU, AS, CHN, KOR): 1575, D150(NA, TW): 1300, D150(EU, AS, CHN, KOR): 1560 / 1W/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : center

042

Temp.:Lower Delta:Center:Power A

*ENG

[0 to 200 / D146:40, D147:40, D148:52, D149:40, D150:40 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : center

043

Temp.:Lower Delta::Power A

*ENG

[0 to 200 / D146:40, D147:40, D148:52, D149:40, D150:40 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : edge

044

Temp.:Upper Delta:Center:Power A

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : center

045

Temp.:Upper Delta:End:Power A

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : edge

046

Temp.:Lower Delta:Press:Power A

*ENG

[0 to 200 / D146, D147:77, D148: 71, D149:NA TW: 37, D149(EU, AS, CHN, KOR): 63, D150(NA,

TW): 25, D150(EU, AS, CHN,

KOR): 45 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure

047

Rotation Time:Power A

*ENG

[0 to 100 / 0 / 1sec/step]

Do not change. Paper feed start permission temp. : before decision rotate time

051

Judgment Power B

*ENG

[0 to 2000 / D146(NA, TW): 1320, D146(EU, AS, CHN, KOR): 1430, D147(NA, TW): 1315, D147(EU, AS, CHN, KOR):1425, D148(NA, TW): 1270, D148(EU, AS, CHN, KOR): 1530, D149(NA, TW): 1225, D149(EU, AS, CHN, KOR): 1485, D150(NA, TW): 1215, D150(EU, AS, CHN, KOR): 1475 / 1W/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : center

052

Temp.:Lower Delta:Center:Power B

*ENG

[0 to 200 / D146:40, D147:40, D148:52, D149:40, D150:40 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : center: special mode 1

053

Temp.:Lower Delta:End:Power B

*ENG

[0 to 200 / D146:40, D147:40, D148:52, D149:40, D150:40 /

1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : edge: special mode 1

054

Temp.:Upper Delta:Center:Power B

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : edge: special mode 1

055

Temp.:Upper Delta:End:Power B

*ENG

[0 to 200 / 30 / 1deg/step]

Do not change. Paper feed start permission temp. upper diff from target temp. : edge: special mode 1

056

Temp.:Lower Delta:Press:Power B

*ENG

[0 to 200 / D146, D147:77, D148:71, D149(NA TW): 37, D149(EU, AS, CHN, KOR): 63,

D150(NA, TW): 25, D150(EU, AS,

CHN, KOR): 43 / 1deg/step]

Do not change. Paper feed start permission temp. lower diff from target temp. : pressure: special mode 1

057

Rotation Time:Power B

*ENG

[0 to 100 / 0 / 1sec/step]

Do not change. Paper feed permission setting rotate before decision time: special mode 1

1105

[Print Target Temp.]

001

Plain1:FC:Center

*ENG

[100 to 180 / D146:118, D147:118, D148:131, D149:147, D150:147 /

1deg/step]

Paper through target temperature: Standard paper 1: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

002

Plain1:FC:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:138, D150:138 /

1deg/step]

Do not change. paper through target temperature: Standard paper 1: FC: pressure

003

Plain1:BW:Center

*ENG

[100 to 180 / D146:115, D147:115, D148:126, D149:142, D150:142 /

1deg/step]

Paper through target temperature: Standard paper 1: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

004

Plain1:BW:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:133, D150:133 /

1deg/step]

Do not change. paper through target temperature: Standard paper 1: BW: pressure

005

Plain2:FC:Center

*ENG

[100 to 180 / D146:123, D147:123, D148:141, D149:157, D150:157 /

1deg/step]

Paper through target temperature: Standard paper 2: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

006

Plain2:FC:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:143, D150:143 /

1deg/step]

Do not change. paper through target temperature: Standard paper 2: FC: pressure

007

Plain2:BW:Center

*ENG

[100 to 180 / D146:120, D147:120, D148:136, D149:148, D150:148 /

1deg/step]

Paper through target temperature: Standard paper 2: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

008

Plain2:BW:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:120, D150:120 /

1deg/step]

Do not change. paper through target temperature: Standard paper 2: BW: pressure

009

Thin:FC:Center

*ENG

[100 to 180 / D146:114, D147:114, D148:116, D149:132, D150:132 /

1deg/step]

Paper through target temperature: thin paper: FC: center Fusing malfunction might improve by setting value larger. Paper curl might improve by setting value smaller.

Adjusting range is +/- 5 deg. celsius.

010

Thin:FC:Press

*ENG

[0 to 200 / D146:114, D147:114, D148:116, D149:132, D150:132 /

1deg/step]

Do not change. paper through target temperature: thin paper: FC: pressure

011

Thin:BW:Center

*ENG

[100 to 180 / D146:114, D147:114, D148:116, D149:132, D150:132 /

1deg/step]

Paper through target temperature: thin paper: BW: center Fusing malfunction might improve by setting value larger. Paper curl might improve by setting value smaller.

Adjusting range is +/- 5 deg. celsius.

012

Thin:BW:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thin paper: BW: pressure

013

M-thick:FC:Center

*ENG

[100 to 180 / D146:135, D147:135, D148:141, D149:157, D150:157 /

1deg/step]

Paper through target temperature: middle thick paper: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

014

M-thick:FC:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:140, D150:140 /

1deg/step]

Do not change. paper through target temperature: middle thick paper: FC: pressure

015

M-thick:BW:Center

*ENG

[100 to 180 / D146:135, D147:135, D148:141, D149:152, D150:152 /

1deg/step]

Paper through target temperature: middle thick paper: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

016

M-thick:BW:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:140, D150:140 /

1deg/step]

Do not change. paper through target temperature: middle thick paper: BW: pressure

017

Thick1:FC:Center

*ENG

[100 to 180 / D146:125, D147:125, D148:140, D149:140, D150:140 /

1deg/step]

Paper through target temperature: thick paper 1: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

018

Thick1:FC:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thick paper 1: FC: pressure

019

Thick1:BW:Center

*ENG

[100 to 180 / D146:125, D147:125, D148:140, D149:140, D150:140 /

1deg/step]

Paper through target temperature: thick paper 1: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

020

Thick1:BW:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thick paper 1: BW: pressure

021

Thick2:FC:Center

*ENG

[100 to 180 / 130 / 1deg/step]

paper through target temperature: thick paper 2: FC: center Fusing malfunction might improve by setting value larger. Paper curl might improve by setting value smaller.

Adjusting range is +/- 5 deg. celsius.

022

Thick2:FC:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thick paper 2: FC: pressure

023

Thick2:BW:Center

*ENG

[100 to 180 / 130 / 1deg/step]

Paper through target temperature: thick paper 2: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

024

Thick2:BW:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thick paper 2: BW: pressure

025

Thick3:FC:Center

*ENG

[100 to 180 / 135 / 1deg/step]

Paper through target temperature: thick paper 3: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

026

Thick3:FC:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thick paper 3: FC: pressure

027

Thick3:BW:Center

*ENG

[100 to 180 / 135 / 1deg/step]

Paper through target temperature: thick paper 3: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

028

Thick3:BW:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thick paper 3: BW: pressure

029

Special1:FC:Center

*ENG

[100 to 180 / D146:129, D147:129, D148:131, D149:147, D150:147 /

1deg/step]

Paper through target temperature: special paper 1: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

030

Special1:FC:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:147, D150:147 /

1deg/step]

Do not change. paper through target temperature: special paper 1: FC: pressure

031

Special1:BW:Center

*ENG

[100 to 180 / D146:129, D147:129, D148:131, D149:147, D150:147 /

1deg/step]

Paper through target temperature: special paper 1: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

032

Special1:BW:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:147, D150:147 /

1deg/step]

Do not change. paper through target temperature: special paper 1: BW: pressure

033

Special2:FC:Center

*ENG

[100 to 180 / D146:139, D147:139, D148:141, D149:157, D150:157 /

1deg/step]

Paper through target temperature: special paper 2: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

034

Special2:FC:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:143, D150:143 /

1deg/step]

Do not change. paper through target temperature: special paper 2: FC: pressure

035

Special2:BW:Center

*ENG

[100 to 180 / D146:139, D147:139, D148:141, D149:157, D150:157 /

1deg/step]

Paper through target temperature: special paper 2: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

036

Special2:BW:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:137, D150:137 /

1deg/step]

Do not change. paper through target temperature: special paper 2: BW: pressure

037

Special3:FC:Center

*ENG

[100 to 180 / D146:139, D147:139, D148:141, D149:157, D150:157 /

1deg/step]

paper through target temperature: special paper 3: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

038

Special3:FC:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:137, D150:137 /

1deg/step]

Do not change. paper through target temperature: special paper 3: FC: pressure

039

Special3:BW:Center

*ENG

[100 to 180 / D146:139, D147:139, D148:141, D149:157, D150:157 /

1deg/step]

Paper through target temperature: special paper 3: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

040

Special3:BW:Press

*ENG

[0 to 200 / D146:118, D147:118, D148:118, D149:140, D150:140 /

1deg/step]

Do not change. paper through target temperature: special paper 3: BW: pressure

041

Envelop:Center

*ENG

[100 to 180 / 142 / 1deg/step]

Paper through target temperature: envelope: FC: center Fusing malfunction might improve by setting value larger. Paper curl might improve by setting value smaller.

Adjusting range is +/- 5 deg. celsius.

042

Envelop:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: envelope: FC: pressure

051

Special1:FC:Center:Middle Speed

*ENG

[100 to 180 / D146:122, D147:122, D148:141, D149:141, D150:141 /

1deg/step]

paper through target temperature: special paper 1: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

052

Special1:FC:Press:Middle Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 1: FC: pressure

053

Special1:BW:Center:Middle Speed

*ENG

[100 to 180 / D146:122, D147:122, D148:141, D149:141, D150:141 /

1deg/step]

Paper through target temperature: special paper 1: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

054

Special1:BW:Press:Middle Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 1: BW: pressure

055

Special2:FC:Center:Middle Speed

*ENG

[100 to 180 / D146:127, D147:127, D148:146, D149:146, D150:146 /

1deg/step]

Paper through target temperature: special paper 2: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

056

Special2:FC:Press:Middle Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 2: FC: pressure

057

Special2:BW:Center:Middle Speed

*ENG

[100 to 180 / D146:127, D147:127, D148:146, D149:146, D150:146 /

1deg/step]

Paper through target temperature: special paper 2: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

058

Special2:BW:Press:Middle Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 2: BW: pressure

059

Special3:FC:Center:Middle Speed

*ENG

[100 to 180 / D146: 132, D147: 132,

D148: 151, D149: 151, D150: 151 /

1deg/step]

Paper through target temperature: special paper 3: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

060

Special3:FC:Press:Middle Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 3: FC: pressure

061

Special3:BW:Center:Middle Speed

*ENG

[100 to 180 / D146: 132, D147: 132,

D148: 151, D149: 151, D150: 151 /

1deg/step]

Paper through target temperature: special paper 3: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

062

Special3:BW:Press:Middle Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 3: BW: pressure

101

Plain1:FC:Center:Low Speed

*ENG

[100 to 180 / 115 / 1deg/step]

Paper through target temperature: Standard 1: FC: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

102

Plain1:FC:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: Standard 1: FC: pressure: low speed

103

Plain1:BW:Center:Low Speed

*ENG

[100 to 180 / 115 / 1deg/step]

Paper through target temperature: Standard 1: BW: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

104

Plain1:BW:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: Standard 1: BW: pressure: low speed

105

Plain2:FC:Center:Low Speed

*ENG

[100 to 180 / 120 / 1deg/step]

Paper through target temperature: Standard 2: FC: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

106

Plain2:FC:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: Standard 2: FC: pressure: low speed

107

Plain2:BW:Center:Low Speed

*ENG

[100 to 180 / 120 / 1deg/step]

Paper through target temperature: Standard 2: BW: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

108

Plain2:BW:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: Standard 2: BW: pressure: low speed

109

M-thick:FC:Center:Low Speed

*ENG

[100 to 180 / 135 / 1deg/step]

Paper through target temperature: middle thick paper: FC: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

110

M-thick:FC:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: middle thick paper: FC: pressure: low speed

111

M-thick:BW:Center:Low Speed

*ENG

[100 to 180 / 135 / 1deg/step]

Paper through target temperature: middle thick paper: BW: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

112

M-thick:BW:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: middle thick paper: BW: pressure: low speed

113

Thick1:FC:Center:Low Speed

*ENG

[100 to 180 / 128 / 1deg/step]

Paper through target temperature: Thick paper 1: FC: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

114

Thick1:FC:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: Thick paper 1: FC: pressure: low speed

115

Thick1:BW:Center:Low Speed

*ENG

[100 to 180 / 127 / 1deg/step]

Paper through target temperature: Thick paper 1: BW: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

116

Thick1:BW:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: Thick paper 1: BW: pressure: low speed

117

Special1:FC:Center:Low Spee

*ENG

[100 to 180 / 137 / 1deg/step]

paper through target temperature: Thick paper 1: BW: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

118

Special1:FC:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 1: FC: pressure: low speed

119

Special1:BW:Center:Low Speed

*ENG

[100 to 180 / 137 / 1deg/step]

Paper through target temperature: special paper 1: BW: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

120

Special1:BW:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 1: BW: pressure: low speed

121

Special2:FC:Center:Low Speed

*ENG

[100 to 180 / 142 / 1deg/step]

Paper through target temperature: special paper 2: FC: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

122

Special2:FC:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 2: FC: pressure: low speed

123

Special2:BW:Center:Low Speed

*ENG

[100 to 180 / 142 / 1deg/step]

Paper through target temperature: special paper 2: BW: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

124

Special2:BW:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 2: BW: pressure: low speed

125

Plain1:Glossy:Center

*ENG

[100 to 180 / 132 / 1deg/step]

Paper through target temperature: Standard paper 1: coat: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

126

Plain1:Glossy:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature coat: standard 1: pressure

127

Plain2:Glossy:Center

*ENG

[100 to 180 / 137 / 1deg/step]

Paper through target temperature: Standard paper 2: coat: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

128

Plain2:Glossy:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature coat: standard 2: pressure

129

M-thick:Glossy:Center

*ENG

[100 to 180 / 142 / 1deg/step]

Paper through target temperature: Standard paper 2: coat: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

130

M-thick:Glossy:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature coat: middle thick: pressure

131

OHP:Center

*ENG

[100 to 180 / 160 / 1deg/step]

paper through target temperature OHP: center

Fusing malfunction might improve by setting value larger. Paper curl might improve by setting value smaller.

Adjusting range is +/- 5 deg. celsius.

132

OHP:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature OHP: pressure

133

Envelop:Center:Low Speed

*ENG

[100 to 180 / 142 / 1deg/step]

Paper through target temperature: envelope: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

134

Envelop:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: envelope: pressure: low speed

135

Thin:FC:Center:Low Speed

*ENG

[100 to 180 / 110 / 1deg/step]

Paper through target temperature: thin paper: FC: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

136

Thin:FC:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thin paper: FC: pressure: low speed

137

Thin:BW:Center:Low Speed

*ENG

[100 to 180 / 110 / 1deg/step]

Paper through target temperature: thin paper: BW: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

138

Thin:BW:Press:Low Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thin paper: BW: pressure: low speed

139

Thick4:FC:Center

*ENG

[100 to 180 / 147 / 1deg/step]

Paper through target temperature: thick paper 4: FC: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

140

Thick4:FC:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thick paper 4: FC: pressure

141

Thick4:BW:Center

*ENG

[100 to 180 / 147 / 1deg/step]

Paper through target temperature: thick paper 4: BW: center Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

142

Thick4:BW:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: thick paper 4: BW: pressure

143

Postcard:Center

*ENG

[100 to 180 / 118 / 1deg/step]

Paper through target temperature post card: center Fusing malfunction might improve by setting value larger. Paper curl might improve by setting value smaller.

Adjusting range is +/- 5 deg. celsius.

144

Postcard:Press

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature post card: pressure

145

Special3:FC:Center:Middle Speed

*ENG

[100 to 180 / 147 / 1deg/step]

Paper through target temperature: Thick paper 1: BW: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

146

Special3:FC:Press:Middle Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 1: FC: pressure: low speed

147

Special3:BW:Center:Middle Speed

*ENG

[100 to 180 / 147 / 1deg/step]

Paper through target temperature: special paper 1: BW: center: low speed Fusing malfunction might improve by setting value larger.

Paper curl might improve by setting value smaller. Adjusting range is +/- 5 deg. celsius.

148

Special3:BW:Press:Middle Speed

*ENG

[0 to 200 / 118 / 1deg/step]

Do not change. paper through target temperature: special paper 1: BW: pressure: low speed

1106

[Fusing Temp. Display]

001

Heat Center

ENG

[-10 to 250 / 0 / 1deg/step]

Display fusing temperature: Displays detect temperature of heating center sensor.

002

Heat End

ENG

[-10 to 250 / 0 / 1deg/step]

Display fusing temperature: Displays detect temperature of heating edge sensor.

003

Press Center

ENG

[-10 to 250 / 0 / 1deg/step]

Display fusing temperature: Displays detect temperature of pressuring edge sensor.

004

Press End

ENG

[-10 to 250 / 0 / 1deg/step]

Display fusing temperature: Displays detect temperature of pressuring edge sensor.

005

Press End

ENG

[-10 to 250 / 0 / 1deg/step]

Display fusing temperature: Displays detect temperature of pressuring extension edge sensor.

1107

[Standby Target Temp. Setting]

001

Stanby/Preheat1:Center

*ENG

[0 to 200 / 90 / 1deg/step]

Do not change. Ready/pre-heat 1 target temperature: center

003

Preheat2:Center

*ENG

[0 to 200 / 90 / 1deg/step]

Do not change. Pre-heat 2 target temperature: pressure

005

Low Power:Center

*ENG

[0 to 200 / 60 / 1deg/step]

Do not change. Energy save target temperature: pressure

007

Print Ready:Center

*ENG

[100 to 180 / D146, D147: 128, D148(NA, TW): 141, D148(EU, AS, CHN, KOR): 131, D149, D150(NA, TW): 157, D149, D150(EU, AS, CHN, KOR): 147 /

1deg/step]

Do not change. Prepare printing target temperature: fusing

008

Print Ready:Press

*ENG

[0 to 200 / 120 / 1deg/step]

Do not change. Prepare printing target temperature: pressure

011

Standby Heater Off Time

*ENG

[0 to 100 / 0 / 1sec/step]

Do not change. After switching to ready, turn heater 3 OFF until passes.

1108

[After Reload/Job Target Temp.]

001

Center

*ENG

[0 to 200 / D146:123, D147:123, D148:141, D149:157, D150:157 /

1deg/step]

Do not change. After reload/after paper through target temperature: center

002

Press

*ENG

[0 to 200 / 120 / 1deg/step]

Do not change. After reload/after paper through target temperature: pressure

011

Center:Energy Saving

*ENG

[0 to 200 / D146:112, D147:112, D148:118, D149:135, D150:135 /

1deg/step]

Do not change. After reload/after paper through target temperature: center: BW2

012

Press:Energy Saving

*ENG

[0 to 200 / 120 / 1deg/step]

Do not change. After reload/after paper through target temperature: pressure: BW2

1111

[Environment Correction:Fusing]

001

Temp.: Threshold: Low

*ENG

[0 to 100 / 17 / 1deg/step]

Do not change. Threshold to decide low temp. environment

002

Temp.: Threshold: High

*ENG

[0 to 100 / 30 / 1deg/step]

Do not change. Threshold to decide high temp. environment

003

Low Temp. Correction

*ENG

[0 to 15 / D146:5, D147:5, D148:15,

D149:15, D150:15 / 1deg/step]

Do not change. Correction temp. for stand up, standby when under low temp. environment

004

High Temp. Correction

*ENG

[0 to 15 / 0 / 1deg/step]

Do not change. Correction temp. for stand up, standby when under high temp. environment

005

Job Low Temp. Correction

*ENG

[0.0 to 100.0 / D146:5.0, D147:5.0, D148:10.0, D149:10.0, D150:10.0 /

0.1deg/step]

Do not change. Correction temp. for pass trough paper when under low temp. environment

006

Job High Temp. Correction

*ENG

[0.0 to 100.0 / 0.0 / 0.1deg/step]

Do not change. Correction temp. for pass trough paper when under high temp. environment

007

Job Low Temp. Correction:Sp.

*ENG

[0.0 to 100.0 / D146:5.0, D147:5.0, D148:10.0, D149:10.0, D150:10.0 /

0.1deg/step]

Do not change. Special mode correction temp. for pass trough paper when under low temp. environment

008

Job High Temp. Correction:Sp.

*ENG

[0.0 to 100.0 / 0.0 / 0.1deg/step]

Do not change. Special mode correction temp. for pass trough paper when under high temp. environment

011

Standard Environment Temp.

*ENG

[10 to 30 / 23 / 1deg/step]

Do not change. Standard environment temperature

1112

[Image Processing Temp. Correct]

001

Temp.:Plain:Center:Level1/2

*ENG

[-20 to 20 / 0 / 1deg/step]

Do not change. Image process temperature correction: standard paper: Level 1

002

Temp.:Plain:Center:Energy Saving

*ENG

[-30 to 20 / D146:-7, D147:-7, D148:-15, D149:-16, D150:-16 /

1deg/step]

Image process temperature correction: standard paper: Level 2

Fusing malfunction to standard paper, Bk monochrome images might improve by setting value larger.

Adjustable range is between +/- 0 deg. Celsius to initial value.

1113

[Curl Correction]

001

Execute Pattern

*ENG

[0 to 2 / 0 / 1/step]

0: OFF

1: ON(No Decurl)

2: ON

Enable/disable curl correction.

002

Humidity:Threshold:M-humid

*ENG

[0 to 100 / 1 / 1%/step]

Do not change. Curl correct humidity: threshold: middle humidity

003

Humidity:Threshold:H-humid

*ENG

[0 to 100 / 65 / 1%/step]

Do not change. Curl correct humidity: threshold: high humidity

004

Permit Temp.:Delta:Press:M-humid

*ENG

[0 to 200 / D146:60, D147:60, D148:40, D149:40, D150:40 /

1deg/step]

Do not change. Curl correction approve temperature: diff.: pressure: middle humidity

005

Permit Temp.:Delta:Press:H-humid

*ENG

[0 to 200 / D146:60, D147:60, D148:40, D149:40, D150:40 /

1deg/step]

Do not change. Curl correction approve temperature: diff.: pressure: high humidity

006

Permit

Temp.:Delta:Press:M-humid:No Decurl

*ENG

[0 to 200 / D146:50, D147:50, D148:30, D149:30, D150:30 /

1deg/step]

Do not change. Curl correction approve temperature: diff.: pressure: middle humidity: de-curler not went through

007

Permit

Temp.:Delta:Press:H-humid:No Decurl

*ENG

[0 to 200 / D146:40, D147:40, D148:20, D149:20, D150:20 /

1deg/step]

Do not change. Curl correction approve temperature: diff.: pressure: middle humidity: de-curler not went through

008

CPM:M-humid

*ENG

[0 to 100 / 80 / 1%/step]

Do not change. Curl correction CPM: middle humidity

009

CPM:H-humid

*ENG

[0 to 100 / 65 / 1%/step]

Do not change. Curl correction CPM: high humidity

010

CPM:M-humid:No Decurl

*ENG

[0 to 100 / 80 / 1%/step]

Do not change. Curl correction CPM: middle humidity: de-curler not went through

011

CPM:H-humid:No Decurl

*ENG

[0 to 100 / 65 / 1%/step]

Do not change. Curl correction CPM: high humidity: de-curler not went through

1114

[Heat Storage Status]

001

Temp.:Threshold:Press

*ENG

[0 to 200 / 80 / 1deg/step]

Do not change. Pressuring temperature thresh to judge heat accumulation.

002

Temp.:Threshold:Atmosphere

*ENG

[0 to 200 / 60 / 1deg/step]

Do not change. Audience temperatures thresh to judge heat accumulation.

003

Temp.:Threshold:CPM down

*ENG

[0 to 200 / 60 / 1deg/step]

Do not change. Pressuring temperature thresh to judge heat accumulation.

004

Temp.:Threshold:Voltage Detection

*ENG

[0 to 200 / 40 / 1deg/step]

Do not change. Judge heat accumulation: voltage detecting pressure temperature thresh

1115

[Target Temp. Correction]

001

Temp.:Delta:End

*ENG

[-100 to 100 / 0 / 1deg/step]

Do not change. Target temperature differential value of center and edge

1116

[Heat Storage FB Control]

001

Execution mode

*ENG

[0 to 2 / 0 / 1/step]

0: OFF

1: ON(BW)

2: ON(BW/FC)

Do not change. Applying area of heat accumulate amount FB control

011

Time Out

*ENG

[0 to 500 / 10 / 1sec/step]

Do not change. Time from start paper through to start temperature correct.

021

Delay:Standard Speed:FC:1

*ENG

[0 to 20000 / D146:3590, D147:3590, D148:2810, D149:2050, D150:2050 /

1msec/step]

Do not change. Time to get pressure temperature from F GATE standard peed: FC: 1

022

Delay:Standard Speed:BW:1

*ENG

[0 to 20000 / D146:1320, D147:1320, D148:1040, D149:760,

D150:760 / 1msec/step]

Do not change. Time to get pressure temperature from F GATE standard peed: BW: 1

031

Delay:Standard Speed:FC:2

*ENG

[0 to 20000 / D146:3590, D147:3590, D148:2810, D149:2050, D150:2050 /

1msec/step]

Do not change. Do not change. Time to get pressure temperature from F GATE standard peed: FC: 2

032

Delay:Standard Speed:BW:2

*ENG

[0 to 20000 / D146:1320, D147:1320, D148:1040, D149:760,

D150:760 / 1msec/step]

Do not change. Time to get pressure temperature from F GATE standard peed: BW: 2

041

Press Reference Temp.

*ENG

[0 to 200 / D146:70, D147:70, D148:75, D149:75, D150:75 /

1deg/step]

Do not change. Pressuring temperature to calculate correction value

042

Temp. Correction Lower Limit

*ENG

[-30 to 0 / -1 / 1deg/step]

Do not change. Lower limit of temperature correcting value

043

Temp. Correction Upper Limit

*ENG

[0 to 30 / 0 / 1deg/step]

Do not change. Upper limit of temperature correcting value

051

Paper Thickness Coefficient:Plain1

*ENG

[0 to 100 / 30 / 1/step]

Do not change. Coefficient to calculate temperature correction value standard paper 1

052

Paper Thickness Coefficient:Plain2

*ENG

[0 to 100 / 30 / 1/step]

Do not change. Coefficient to calculate temperature correction value standard paper 2

1117

[Repeat Temp. Correction]

Do not change.

001

Control Time 1:A3

*ENG

[0 to 300 / 0 / 1sec/step]

002

Control Time 2:A3

*ENG

[0 to 300 / 0 / 1sec/step]

003

Temp.:Center:1:A3

*ENG

[-30 to 30 / 0 / 1deg/step]

004

Temp.:End:1:A3

*ENG

[-30 to 30 / 0 / 1deg/step]

005

Temp.:Center:2:A3

*ENG

[-30 to 30 / 0 / 1deg/step]

006

Temp.:End:2:A3

*ENG

[-30 to 30 /0 / 1deg/step]

011

Control Time 1:DLT

*ENG

[0 to 300 / D146:60, D147:51 D148:40,D149:33, D150:30 /

1sec/step]

012

Control Time 2:DLT

*ENG

[0 to 300 / D146:60, D147:51 D148:40,D149:33, D150:30 /

1sec/step]

013

Temp.:Center:1:DLT

*ENG

[-30 to 30 / 0 / 1deg/step]

014

Temp.:End:1:DLT

*ENG

[-30 to 30 / D146:0, D147:0, D148:-5, D149:-5, D150:-5 /

1deg/step]

015

Temp.:Center:2:DLT

*ENG

[-30 to 30 / 0 / 1deg/step]

016

Temp.:End:2:DLT

*ENG

[-30 to 30 / D146:0, D147:0, D148:-10, D149:-10, D150:-10 /

1deg/step]

021

Control Time 1:B4

*ENG

[0 to 300 / 0 / 1sec/step]

022

Control Time 2:B4

*ENG

[0 to 300 / D146:10, D147:9, D148:7, D149:5, D150:5 /

1sec/step]

023

Temp.:Center:1:B4

*ENG

[-30 to 30 / 0 / 1deg/step]

024

Temp.:End:1:B4

*ENG

[-30 to 30 / 25 / 1deg/step]

025

Temp.:Center:2:B4

*ENG

[-30 to 30 / 0 / 1deg/step]

026

Temp.:End:2:B4

*ENG

[-30 to 30 / 25 / 1deg/step]

031

Control Time 1:LT

*ENG

[0 to 300 / 0 / 1sec/step]

032

Control Time 2:LT

*ENG

[0 to 300 / 0 / 1sec/step]

033

Temp.:Center:1:LT

*ENG

[-30 to 30 / 6 / 1deg/step]

034

Temp.:End:1:LT

*ENG

[-30 to 30 / 21 / 1deg/step]

035

Temp.:Center:2:LT

*ENG

[-30 to 30 / 6 / 1deg/step]

036

Temp.:End:2:LT

*ENG

[-30 to 30 / 21 / 1deg/step]

041

Control Time 1:A3,DLT:Energy Saving

*ENG

[0 to 300 / D146:3, D147:3, D148:2, D149:0, D150:0 /

1sec/step]

042

Control Time 2:A3,DLT:Energy Saving

*ENG

[0 to 300 / D146:40, D147:40, D148:60, D149:60, D150:60 /

1sec/step]

043

Temp.:Center:1:A3,DLT:Energy Saving

*ENG

[-30 to 30 / D146:1, D147:1, D148:3, D149:3, D150:3 /

1deg/step]

044

Temp.:End:1:A3,DLT:Energy Saving

*ENG

[-30 to 30 / 0 / 1deg/step]

045

Temp.:Center:2:A3,DLT:Energy Saving

*ENG

[-30 to 30 / D146:4, D147:4, D148:5, D149:6, D150:6 /

1deg/step]

046

Temp.:End:2:A3,DLT:Energy Saving

*ENG

[-30 to 30 / 3 / 1deg/step]

051

Control Time 1:A4

*ENG

[0 to 300 / 0 / 1sec/step]

052

Control Time 2:A4

*ENG

[0 to 300 / 0 / 1sec/step]

053

Temp.:Center:1:A4

*ENG

[-30 to 30 / 0 / 1deg/step]

054

Temp.:End:1:A4

*ENG

[-30 to 30 / D146 and D147(NA, TW), D148, D149, D150( ALL):21, D146, D147(EU, AS,

CHN, KOR): 0 / 1deg/step]

055

Temp.:Center:2:A4

*ENG

[-30 to 30 / D146 and D147(NA, TW), D148, D149, D150( ALL):6, D146, D147(EU, AS,

CHN, KOR): 0 / 1deg/step]

056

Temp.:End:2:A4

*ENG

[-30 to 30 / 0 / 1deg/step]

061

Control Time 1:A3:M-thick

*ENG

[0 to 300 / 0 / 1sec/step]

062

Control Time 2:A3:M-thick

*ENG

[0 to 300 / 0 / 1sec/step]

063

Temp.:Center:1:A3:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

064

Temp.:End:1:A3:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

065

Temp.:Center:2:A3:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

066

Temp.:End:2:A3:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

071

Control Time 1:DLT:M-thick

*ENG

[0 to 300 / D146:60, D147:51, D148:40, D149:33, D150:30 /

1sec/step]

072

Control Time 2:DLT:M-thick

*ENG

[0 to 300 / D146:60, D147:51, D148:40, D149:33, D150:30 /

1sec/step]

073

Temp.:Center:1:DLT:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

074

Temp.:End:1:DLT:M-thick

*ENG

[-30 to 30 / D146:0, D147:0, D148:-5, D149:-5, D150:-5 /

1deg/step]

075

Temp.:Center:2:DLT:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

076

Temp.:End:2:DLT:M-thick

*ENG

[-30 to 30 / D146:0, D147:0, D148:-10, D149:-10, D150:-10 /

1deg/step]

081

Control Time 1:Envelope:Long

*ENG

[0 to 300 / 0 / 1sec/step]

082

Control Time 2:Envelope:Long

*ENG

[0 to 300 / 0 / 1sec/step]

083

Temp.:Center:1:Envelope:Long

*ENG

[-30 to 30 / 0 / 1deg/step]

084

Temp.:End:1:Envelope:Long

*ENG

[-30 to 30 / 10 / 1deg/step]

085

Temp.:Center:2:Envelope:Long

*ENG

[-30 to 30 / 0 / 1deg/step]

086

Temp.:End:2:Envelope:Long

*ENG

[-30 to 30 / 10 / 1deg/step]

091

Control Time 1:Envelope:Short

*ENG

[0 to 300 / 0 / 1sec/step]

092

Control Time 2:Envelope:Short

*ENG

[0 to 300 / 0 / 1sec/step]

093

Temp.:Center:1:Envelope:Short

*ENG

[-30 to 30 / 0 / 1deg/step]

094

Temp.:End:1:Envelope:Short

*ENG

[-30 to 30 / 0 / 1deg/step]

095

Temp.:Center:2:Envelope:Short

*ENG

[-30 to 30 / 0 / 1deg/step]

096

Temp.:End:2:Envelope:Short

*ENG

[-30 to 30 / 0 / 1deg/step]

101

Control Time 1:B5

*ENG

[0 to 300 / 0 / 1sec/step]

102

Control Time 2:B5

*ENG

[0 to 300 / 0 / 1sec/step]

103

Temp.:Center:1:B5

*ENG

[-30 to 30 / 0 / 1deg/step]

104

Temp.:End:1:B5

*ENG

[-30 to 30 / -30 / 1deg/step]

105

Temp.:Center:2:B5

*ENG

[-30 to 30 / 0 / 1deg/step]

106

Temp.:End:2:B5

*ENG

[-30 to 30 /-30 / 1deg/step]

111

Control Time 1:12inch

*ENG

[0 to 300 / 0 / 1sec/step]

112

Control Time 2:12inch

*ENG

[0 to 300 / 0 / 1sec/step]

113

Temp.:Center:1:12inch

*ENG

[-30 to 30 / 0 / 1deg/step]

114

Temp.:End:1:12inch

*ENG

[-30 to 30 / 0 / 1deg/step]

115

Temp.:Center:2:12inch

*ENG

[-30 to 30 / 0 / 1deg/step]

116

Temp.:End:2:12inch

*ENG

[-30 to 30 / 0 / 1deg/step]

121

Control Time 1:12inch:M-thick

*ENG

[0 to 300 / 0 / 1sec/step]

122

Control Time 2:12inch:M-thick

*ENG

[0 to 300 / 0 / 1sec/step]

123

Temp.:Center:1:12inch:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

124

Temp.:End:1:12inch:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

125

Temp.:Center:2:12inch:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

126

Temp.:End:2:12inch:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

131

Control Time 1:SRA3

*ENG

[0 to 300 / 0 / 1sec/step]

132

Control Time 2:SRA3

*ENG

[0 to 300 / D146:6, D147:6, D148:160, D149:132, D150:120 /

1sec/step]

133

Temp.:Center:1:SRA3

*ENG

[-30 to 30 / D146:25, D147: 25,

D148: 20, D149: 20, D150: 20 /

1deg/step]

134

Temp.:End:1:SRA3

*ENG

[-30 to 30 / 25 / 1deg/step]

135

Temp.:Center:2:SRA3

*ENG

[-30 to 30 / 0 / 1deg/step]

136

Temp.:End:2:SRA3

*ENG

[-30 to 30 / 0 / 1deg/step]

141

Control Time 1:SRA3:M-thick

*ENG

[0 to 300 / 0 / 1sec/step]

142

Control Time 2:SRA3:M-thick

*ENG

[0 to 300 / D146:25, D147:25, D148:160, D149:132, D150:120 /

1sec/step]

143

Temp.:Center:1:SRA3:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

144

Temp.:End:1:SRA3:M-thick

*ENG

[-30 to 30 / D146:20, D147: 20,

D148: 0, D149: 0, D150: 0 /

1deg/step]

145

Temp.:Center:2:SRA3:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

146

Temp.:End:2:SRA3:M-thick

*ENG

[-30 to 30 / 0 / 1deg/step]

151

Control Time 1:DLT:Low

*ENG

[0 to 300 / 0 / 1sec/step]

152

Control Time 2:DLT:Low

*ENG

[0 to 300 / 0 / 1sec/step]

153

Temp.:Center:1:DLT:Low

*ENG

[-30 to 30 / 0 / 1deg/step]

154

Temp.:End:1:DLT:Low

*ENG

[-30 to 30 / 5 / 1deg/step]

155

Temp.:Center:2:DLT:Low

*ENG

[-30 to 30 / 0 / 1deg/step]

156

Temp.:End:2:DLT:Low

*ENG

[-30 to 30 / 5 / 1deg/step]

161

Control Time 1:DLT:M-thick:Low

*ENG

[0 to 300 / 0 / 1sec/step]

162

Control Time 2:DLT:M-thick:Low

*ENG

[0 to 300 / 0 / 1sec/step]

163

Temp.:Center:1:DLT:M-thick:Low

*ENG

[-30 to 30 / 0 / 1deg/step]

164

Temp.:End:1:DLT:M-thick:Low

*ENG

[-30 to 30 / 5 / 1deg/step]

165

Temp.:Center:2:DLT:M-thick:Low

*ENG

[-30 to 30 / 0 / 1deg/step]

166

Temp.:End:2:DLT:M-thick:Low

*ENG

[-30 to 30 / 5 / 1deg/step]

1118

[Before Job Temp. Correct]

Do not change.

001

Temp.:Center:12inch

*ENG

[-30 to 30 / 0 / 1deg/step]

002

Temp.:End:12inch

*ENG

[-30 to 30 / 10 / 1deg/step]

003

Temp.:Center:A3

*ENG

[-30 to 30 / 0 / 1deg/step]

004

Temp.:End:A3

*ENG

[-30 to 30 / 0 / 1deg/step]

005

Temp.:Center:DLT

*ENG

[-30 to 30 / 0 / 1deg/step]

006

Temp.:End:DLT

*ENG

[-30 to 30 / 0 / 1deg/step]

007

Temp.:Center:SRA3

*ENG

[-30 to 30 / 0 / 1deg/step]

008

Temp.:End:SRA3

*ENG

[-30 to 30 / 20 / 1deg/step]