HOME PAGE | < Previous | Contents | Next >
Internal Finisher SR3180 (D766)
2.19.2 INSTALLATION PROCEDURE
When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
This option cannot be used together with the following peripherals:
- Internal Shift Tray SH3070 (D691)
- Side Tray Type M3 (D725)
- Internal Finisher SR 3130 (D690)
- Bridge Unit BU3070 (D685)
For using this option together with "1 Bin Tray BN3110 (D3CQ)", attach the bottom plate of this option at the beginning, then install the "1 Bin Tray BN3110 (D3CQ)", followed by installing this option.
1. Remove the orange tapes and shipping retainers.
Internal Finisher SR3180 (D766)
Installation
Installation
Installation
2. Remove the knob screw and red tag [A].
3. Remove the shaft [B] from the slide rail [A] 
x 1).
4. Remove the paper exit cover [A] 
x 2).
5. Place the slide rail [A] under the internal finisher [B].
6. Insert the shaft [A] into the holes located in the slide rail and internal finisher, and then
Internal Finisher SR3180 (D766)
fasten with the screw 
x 1).
7. Attach the paper exit cover (removed in step 4) [A] 
x 2).
8. Remove the paper exit tray [A].
9. Remove the paper exit feeler [A].
Internal Finisher SR3180 (D766)
Installation
Installation
Installation
10. Open the front cover, and then remove the left upper cover [A] 
x 1).
11.
12. Remove the inverter tray [A] and tray support plate [B].
13. Open the right door, and then remove the small cover [A].
Internal Finisher SR3180 (D766)
14. Remove the screw and connector, and then remove the front upper cover [A].
Remember that there are three tabs at the positions of the red arrows.
Tilt the operation panel [B] upward to a horizontal position, and then remove the front upper cover [A].
15. Remove the paper exit cover [A] 
x 1).
Installation
Installation
Installation
Internal Finisher SR3180 (D766)
16. Remove the connector cover [A].
17. Remove the paper exit lower cover [A].
The lower inside cover can be removed together with the paper exit lower cover, since the inside cover is secured on the paper exit lower cover with two screws.
18. Remove the lower inside cover [B] from the paper exit lower cover [A] 
x 2).
Internal Finisher SR3180 (D766)
19. Remove the upper inside cover [A] 
x 2).
20. Insert the bottom plate [A] into the holes.
21. Install the bottom plate [A] 
x 3, Accessory No. 7).
Installation
Installation
Installation
Internal Finisher SR3180 (D766)
22. Install the lower inside cover (removed in step 18) [A] in the finisher 
x 2, Accessory No.5).
23. Reattach the upper inside cover (removed in step 19) [A] 
x 2).
24. Reattach the tray support plate (removed in step 12) [A].
Internal Finisher SR3180 (D766)
25. Reattach the paper exit cover (removed in step 15 and step 16) [A] and the connector cover [B].
Touching the moving parts inside of the cover can result in an injury. To avoid this, be sure to install the connector cover [B].
26. Reattach the front upper cover (removed in step 14) and then close the right door.
27. Remove the driven roller [B] at the machine’s exit tray and attach the supplied driven roller [A].
Insert a flathead screwdriver into the depression in the center, and then, lifting the driven roller, unlock the part indicated by the red arrow.
When attaching the driven roller, push its center all the way in until it clicks.
Installation
Installation
Installation
Internal Finisher SR3180 (D766)
[A]: The supplied driven roller has flat rollers.
[B]: The machine’s standard driven roller has drum-type rollers (as indicated by red frames).
28. Attach the paper support guide [A] (Tab x 4).
29. Install the internal finisher [A].
Internal Finisher SR3180 (D766)
30. Secure the finisher 
x 1, Accessory No.8).
31. Reattach the left rear cover [A]
32. Reattach the left upper cover [A].
33. Attach the left lower cover [A] 
x 2, Accessory No.6).
Installation
Installation
Installation
Internal Finisher SR3180 (D766)
34. Attach the paper exit tray [A] 
x 2, Accessory No.4).
35. Reattach the inverter tray [A] removed in step 12.
36. Remove the connector cover [A] (Release the tab).
Internal Finisher SR3180 (D766)
37. Connect the interface cable [A].
38. Attach the nylon clamp [A] as shown below 
x 1, Accessory No.9).
39. Turn ON the main power.
40. Ensure that the operation panel displays finisher jobs properly and that it works properly.