1001

Bit Switch

001

Bit Switch 1

0

1

bit 0

DFU

-

-

bit 1

DFU

-

-

bit 2

DFU

-

-

bit 3

No I/O Timeout

0: Disable

1: Enable

Enable: The MFP I/O Timeout setting will have no effect. I/O Timeouts will never occur.

bit 4

SD Card Save Mode

0: Disable

1: Enable

Enable: Print jobs will be saved to an SD Card in the GW SD slot.

bit 5

DFU

-

-

bit 6

DFU

-

-

bit 7

[RPCS,PCL]: Printable area frame border

0: Disable

1: Enable

Enable: The machine prints all RPCS and PCL jobs with a border on the edges of the printable area.

1001

Bit Switch

002

Bit Switch 2

0

1

bit 0

DFU

-

-

bit 1

DFU

-

-

bit 2

Applying a collation Type

Shift Collate

Normal Collate

A collation type (shift or normal) will be applied to all jobs that do not already have a ‘Collate Type’ configured.

 If #5-0 is enabled, this Bit Switch has no effect.

bit 3

[PCL5e/c,PS]: PDL Auto Switching

0: Enable

1: Disable

Disable: The MFPs ability to change the PDL processor mid-job.

Some host systems submit jobs that contain both PS and PCL5e/c. If Auto PDL switching is disabled, these jobs will not be printed properly.

bit 4

DFU

-

-

bit 5

DFU

-

-

bit 6

DFU

-

-

bit 7

DFU

-

-

1001

Bit Switch

003

Bit Switch 3

0

1

bit 0

DFU

-

-

bit 1

DFU

-

-

bit 2

[PCL5e/c]: Legacy HP compatibility

0: Disable

1: Enable

Enable: Uses the same left margin as older HP models such as HP4000/HP8000.

In other words, the left margin defined in the job (usually "<ESC>*r0A") will be changed to "<ESC>*r1A"

bit 3

DFU

-

-

bit 4

DFU

-

-

bit 5

DFU

-

-

bit 6

DFU

-

-

bit 7

DFU

-

-

1001

Bit Switch

004

Bit Switch 4

0

1

bit 0

DFU

-

-

bit 1

DFU

-

-

bit 2

DFU

-

-

bit 3

IPDS print-side reversal

0: Disable

1: Enable

Enable: Increases printing speed but simplex pages may be printed on the back side of the sheet.

bit 4

DFU

-

-

bit 5

DFU

-

-

bit 6

DFU

-

-

bit 7

DFU

-

-

1001

Bit Switch

005

Bit Switch 5

0

1

bit 0

Show "Collate Type", "Staple Type" and "Punch Type" buttons on the operation panel.

Disable

Enable

If enabled, users will be able to configure a Collate Type, Staple Type, and Punch Type from the operation panel. The available types will depend on the device and configured options.

After enabling the function, the settings will appear under: "User Tools > Printer Features > System"

bit 1

Multiple copies if a paper size or type mismatch occurs

0: Disable (Single copy)

1: Enable (Multiple copy)

If a paper size or type mismatch occurs during the printing of multiple copies, only a single copy is output by default. Using this Bit Switch, the device can be configured to print all copies even if a paper mismatch occurs.

bit 2

DFU

-

-

bit 3

[PS] PS Criteria

Pattern3

Pattern1

Change the number of PS criterion used by the PS interpreter to determine whether a job is PS data or not.

Pattern3: includes most PS commands.

Pattern1: A small number of PS tags and headers

bit 4

Increase max number of the stored jobs to 1000 jobs.

Disable (100)

Enable (1000)

Enable: Changes the maximum number of jobs that can be stored on the HDD via Job Type settings to 1000. The default is 100.

bit 5

DFU

-

-

bit 6

Method for determining the image rotation for the edge to bind on.

0: Disable

1: Enable

If enabled, the image rotation will be performed as they were in the specifications of older models for the binding of pages of mixed orientation jobs.

The old models are below:

- PCL: Pre-04A models

- PS/PDF/RPCS:Pre-05S models

bit 7

Letterhead mode printing

0: Disable

1: Enable (Duplex)

Routes all pages through the duplex unit.

If this is disabled, simplex pages or the last page of an odd-paged duplex job are not routed through the duplex unit. This could result in problems with letterhead/pre-printed pages.

Only affects pages specified as Letterhead paper.

1001

Bit Switch

006

Bit Switch 6 DFU

-

-

1001

Bit Switch

007

Bit Switch 7

0

1

bit 0

Print path

0: Disable

1: Enable

If enabled, simplex pages (in mixed simplex/duplex PS/PCL5 jobs only) and the last page of an odd paged duplex job (PS, PCL5, PCL6), are always routed through the duplex unit. Not having to switch paper paths increases the print speed slightly.

bit 1

to 7

DFU

-

-

1001

Bit Switch

008

Bit Switch 8 DFU

-

-

1001

Bit Switch

009

Bit Switch 9

0

1

bit 0

PDL Auto Detection timeout of jobs submitted via USB or Parallel Port (IEEE 1284).

"Disabled (Immediately)"

"Enabled (10 seconds)"

To be used if PDL auto-detection fails. A failure of PDL autodetection doesn't necessarily mean that the job can't be printed. This bit switch tells the device whether to time-out immediately (default) upon failure or to wait 10 seconds.

bit 1

DFU

-

-

bit 2

Job Cancel

Disabled (Not cancelled)

Enabled (Cancelled)

If this bit switch, all jobs will be cancelled after a jam occurs.

Note: If this bitsw is enabled, printing under the following conditions might result in problems:

- Job submission via USB or Parallel Port

- Spool printing (WIM >Configuration > Device Settings > System)

bit 3

PCL/PS bypass tray paper rotation (SEF/LEF)

0: Disable

1: Enable

This bitsw causes the device to revert to the behavior of previous generations. It only takes effect if "Bypass Tray Setting Priority" = "Driver/Command".

Previous spec (bitsw=1): If a standard sized paper mismatch occurred in the bypass tray, the MFP always prompted for SEF paper.

If this bitsw=0 (default) then in the event of a standard sized paper mismatch, the MFP will always prompt for paper of the rotation (SEF/LEF) determined by the MFP bypass tray paper setting or by the bypass tray sensor.

bit 4

Response to PJL USTATUS when multiple collated copies are printed

0: Disable

1: Enable

When enabled, if multiple collated copies are printed, the device no longer responds to PJL USTATUS with the number of pages in the current copy. Instead the device will return the total number of pages for all copies.

Bit 5

to 7

DFU

-

-

1001

Bit Switch

010

Bit Switch 10

0

1

bit 0

to 4

DFU

-

-

bit 5

List / Test Print Lock

0: Disable

1: Enable

If enabled, you can lock or unlock the [List/Test Print] items under the Pinter Features menu when the Store and Skip Errored Job Function is on.

Bit 6

Optional charge machines

-

-

If enabled, you can use the optional charge machines when the Store and Skip Errored Job Function is on.

0: Disable

1: Enable

Bit 7

DFU

-

-

1001

Bit Switch

011

Bit Switch 11

0

1

bit 0

List / Test Print menu

0: Disable

1: Enable

When enabled, [Multiple Lists] menu is displayed in [List / Test Print] under the Printer Features menu.

bit 1

Interrupt printing

0: Job

1: Page

Selects the interrupting units for the interrupt printing function. When you select "0," you can interrupt printing of a job while being processed.

When you select "1," you can interrupt printing of a page while being processed.

Bit 2

to 7

DFU

-

-

1001

Bit Switch

012

Bit Switch 12

0

1

bit 0

to 7

DFU

-

-

1003

[Clear Setting]

1003 001

Initialize Printer System

Initializes settings in the "System" menu of the user mode.

1003 003

Delete Program

1004

[Print Summary]

1004 001

Print Printer Summary

Prints the service summary sheet (a summary of all the controller settings).

1006

[Sample/Locked Print]

*CTL

0: Link with Doc. Svr, 1: Enable

1006 001

Enables and disables the document server. When you select "0," the document server is enabled or disabled in accordance with Copy Service Mode SP5-967. When you select "1," the document server is enabled regardless of Copy Service Mode SP5-967.

1110

[Media Print Device Setting]

1110 002

0: Disable 1: Enable

Selects the setting for the media print device.

1111

[All Job Delete Mode]

1111 001

0: excluding New Job

1: including New Job

Select whether to include an image processing job in jobs subject to full cancellation from the SCS job list.