IP Fax Switch 00 (SP No. 1-111-001)

No.

Function

Comments

0

Not used

Do not change this setting.

1

IP Fax Transport 0: TCP, 1: UDP

Selects TCP or UDP protocol for IP-Fax

2

IP Fax single port selection 0: OFF, 1: ON (enable)

Selects single data port.

3

IP Fax double ports (single data port) selection

0: OFF, 1: ON (enable)

Selects whether IP-Fax uses a double port.

4

IP Fax Gatekeeper

0: OFF, 1: ON (enable)

Enables/disables the gatekeeper for IP-Fax.

5

IP Fax T30 bit signal reverse 0: LSB first, 1: MSB first

Reverses the T30 bit signal.

6

IP Fax max bit rate setting 0: Not affected, 1: Affected

When "0" is selected, the max bit rate does not affect the value of the DIS/DCS.

When "1" is selected, the max bit rate affects the value of the DIS/DCS.

7

IP Fax received telephone number confirmation

0: No confirmation, 1: Confirmation

When "0" is selected, fax data is received without checking the telephone number. When "1" is selected, fax data is received only when confirming that the telephone number from the sender matches the registered telephone number in this machine. If this confirmation fails, the line is disconnected.

IP Fax Switch 01 (SP No. 1-111-002)

No.

Function

Comments

0-3

IP Fax delay level setting

Selects the acceptable delay level. Level 0 is the highest quality Default is "0000" (level 0).

Bit 3

Bit 2

Bit 1

Bit 0

0

0

0

0

Level 0

0

0

0

1

Level 1

0

0

1

0

Level 2

0

0

1

1

Level 3

4-7

IP Fax preamble wait time setting

Selects the preamble wait time. [00 to 0f]

There are 16 values in this 4-bit binary switch combination.

Waiting time: set value level x 100 ms Max: 0f (1500 ms) Min: 00 (No wait time) The default is "0000" (00H).

IP Fax Switch 02 (SP No. 1-111-003)

No.

Function

Comments

0

IP Fax bit signal reverse setting 0: Maker code setting

1: Internal bit switch setting

When "0" is selected, the bit signal reverse method is decided by the maker code.

When "1" is selected, the bit signal reverse method is decided by the internal bit switch. When communicating between IP Fax devices, LSB first is selected.)

1

IP Fax transmission speed setting 0: Modem speed

1: No limitation

Selects the transmit speed for IP Fax communication.

2

SIP transport setting 0: TCP

1: UDP

This bit switch sets the transport that has priority for receiving IP Fax data.

This function is activated only when the sender has both TCP and UDP.

3

CCM connection

0: No CCM connection 1: CCM connection

When "1" is selected, only the connection call message with H.323 or no tunneled

H.245 is transmitted via CCM.

4

Message reception selection from non-registered SIP server

0: Answer

1: Not answer

0: This answers the INVITE message from the SIP server not registered for the machine.

1: This does not receive the INVITE message from the SIP server not registered for the machine and send a refusal message.

5

ECM communication setting

0: No limit for image compression 1: Limit for image compression

0: This does not limit the type of the image compression with ECM communication.

1: When the other end machine is Ciscco, this permits the image compression other than JBIG or MMR with ECM communication.

6-7

Not used

Do not change these settings.

IP Fax Switch 03 (SP No. 1-111-004)

No.

Function

Comments

0

Effective field limitation for G3 standard function information 0: OFF, 1: 4byte (DIS)

Limits the effective field for standard G3 function information.

1

Switching between G3 standard and G3 non standard

0: Enable switching 1: G3 standard only

Enables/disables switching between G3 standard and G3 non-standard.

2

Not used

Do not change this setting.

3

ECM frame size selection at transmitting

0: 256byte, 1: 64byte

Selects the ECM frame size for sending.

4

DIS detection times for echo prevention

0: 1 time, 1: 2 times

Sets the number of times for DIS to detect echoes.

5

CTC transmission selection 0: PPRx1

1: PPRx4

When "0" is selected, the transmission condition is decided by error frame numbers.

When "1" is selected, the transmission condition is based on the ITU-T method.

6

Shift down setting at receiving negative code

0: OFF, 1: ON

Selects whether to shift down when negative codes are received.

7

Not used

Do not change this setting.

IP Fax Switch 04 (SP No. 1-111-005)

No.

Function

Comments

0-3

TCF error threshold

Sets the TCF error threshold level. [00 to 0f] The default is "1111" (0fH).

4-7

Not used

Do not change these settings.

IP Fax Switch 05 (SP No. 1-111-006)

No.

Function

Comments

0-3

Modem bit rate setting for transmission (kbps)

Sets the modem bit rate for transmission. The default is "0110" (14.4K bps).

Bit 3

Bit 2

Bit 1

Bit 0

kbps

0

0

0

1

2.4

0

0

1

1

4.8

0

0

1

1

7.2

0

1

0

0

9.6

0

1

0

1

12.0

0

1

1

0

14.4

4-5

Modem setting for transmission

Sets the modem type for transmission.

The default is "00" (V29).

Bit 5

Bit 4

Types

0

0

V29

0

1

V17

1

0

Not used

1

1

Not used

6-7

Not used

Do not change these settings.

IP Fax Switch 06 (SP No. 1-111-007)

No.

Function

Comments

0-3

Modem bit rate setting for reception

Sets the modem bit rate for reception. The default is "0110" (14.4K bps).

4-7

Modem setting for reception

Sets the modem type for reception. The default is "0100" (V27ter, V29, V17).

Bit 7

Bit 6

Bit 5

Bit 4

Types

0

0

0

1

V.27ter

0

0

1

0

V.27ter, V.29

0

0

1

1

V.27ter, V.29, V.33

0

1

0

0

V.27ter, V.29, V.17/V.33

Other settings - Not used

IP Fax Switch 07 (SP No. 1-111-008)

No.

Function

Comments

0

TSI information

0: Not added, 1: Added

Adds or does not add TSI information to NSS(S).

1

DCN transmission setting at T1 timeout

0: Not transmitted

1: Transmitted

Transmits or does not transmit DCN at T1 timeout.

2

Not used

Do not change this setting.

3

Hang up setting at DIS reception disabled

0: No hang up

1: Hang up after transmitting DCN

Sets whether the machine disconnects after DIS reception.

4

Number of times for training 0: 1 time, 1: 2 times

Selects the number of times training is done at the same bit rate.

5

Space CSI transmission setting at no CSI registration

0: Not transmitted

1: Transmitted

When "0" is selected, frame data is enabled. When "1" is selected, the transmitted data is all spaces.

6-7

Not used

Do not change these settings.

IP Fax Switch 08 (SP No. 1-111-009)

No.

Function

Comments

0-1

T1 timer adjustment

Adjusts the T1 timer.

The default is "00" (35 seconds).

Bit 1

Bit 0

0

0

35 s

0

1

40 s

1

0

50 s

1

1

60 s

2-3

T4 timer adjustment

Adjust the T4 timer.

The default is "00" (3 seconds).

Bit 3

Bit 2

0

0

3 s

0

1

3.5 s

1

0

4 s

1

1

5 s

4-5

T0 timer adjustment

Adjusts the fail safe timer. This timer sets the interval between "setup" data transmission and T.38 phase decision. If your destination return is late on the network or G3 fax return is late, adjust the longer interval timer.

The default is "00" (75 seconds).

Bit 5

Bit 4

0

0

75 s

0

1

120 s

1

0

180 s

1

1

240 s

6-7

Not used

Do not change these settings.

IP Fax Switch 09 (SP No. 1-111-010)

No.

Function

Comments

0

Network I/F setting for SIP connection

0: IPv4

1: IPv6.

Selects the connection type (IPV4 or IPV6) to connect to the SIP server.

1

Network I/F setting for Fax communication

0: Same setting as SIP server connection

1: Automatic setting

0: The I/F setting for fax communication follows the setting for SIP server connection.

1: The negotiation between the SIP server and the device decides whether IPv4 or IPv6 is used for the I/F setting for fax communication.

2

Record-route setting 0: Disable

1: Enable

0: Disables the record-route function of the SIP server.

1: Enables the record-route function of the SIP server.

3-4

re-INVITE transmission delay timer setting

This changes the interval for transmit

re-INVITE after receiving the ACK message transmitted by T.38 device.

Bit 4

Bit 3

0

0

No delay

0

1

1 sec

1

0

2 sec

1

1

3 sec

5-7

Not used.

Do not change these settings.

IP Fax Switch 0A - Not used (do not change the settings)

IP Fax Switch 0B - Not used (do not change the settings)

IP Fax Switch 0C - Not used (do not change the settings)

IP Fax Switch 0D - Not used (do not change the settings)

IP Fax Switch 0E - Not used (do not change the settings)