Printer Switch 00 (SP No. 1-103-001)

No

Function

Comments

0

Select page separation marks 0: Off

1: On

0: If a 2 page RX transmission is split, [*] is printed in the bottom right corner of the 1st page and only a [2] is printed in the upper right corner of the 2nd page.

1: If a 2 page RX transmission is split into two pages, for example, [*] [2] is printed in the bottom right corner of the 1st page and only a [2] is printed in the upper right corner of the 2nd page.

 This helps the user to identify pages that have been split because the size of the paper is smaller than the size of the document received. (When A5 is used to print an A4 size document, for example.)

1

Repetition of data when the received page is longer than the printer paper

0: Off

1: On

1: Default. 10 mm of the trailing edge of the previous page are repeated at the top of the next page.

0: The next page continues from where the previous page stopped without any repeated text.

2

Prints the date and time on received fax messages

0: Disabled

1: Enabled

This switch is only effective when user parameter 02 - bit 2 (printing the received date and time on received fax messages) is enabled.

1: The machine prints the received and printed date and time at the bottom of each received page.

3-7

Not used

Do not change the settings.

Printer Switch 01 (SP No. 1-103-002)

No

Function

Comments

0-2

Not used

Do not change the settings.

3-4

Maximum print width used in the setup protocol

These bits are only effective when bit 7 of printer switch 01 is "1".

Bit 4

Bit 3

Setting

0

0

Not used

0

1

A3

1

0

B4

1

1

A4

5-6

Not used

Do not change the settings.

7

Received message width restriction in the protocol signal to the sender

0: Disabled

1: Enabled

0: The machine informs the transmitting machine of the print width depending on the paper size available from the paper feed stations.

Refer to the table on the next page for how the machine chooses the paper width used in the setup protocol (NSF/DIS).

1: The machine informs the transmitting machine of the fixed paper width which is specified by bits 3 and 4 above.

Available Paper Size

Printer width used in the Protocol (NSF/DIS)

A4 or 8.5" x 11"

297 mm width

B5

256 mm width

A5 or 8.5" x 5.5"

216 mm width

No paper available (Paper end)

216 mm width

Printer Switch 02 (SP No. 1-103-003)

No

Function

Comments

0

1st paper feed station usage for fax printing

0: Enabled

1: Disabled

0: The paper feed station can be used to print fax messages and reports.

1: The specified paper feed station will not be used for printing fax messages and reports.

 Do not disable usage for a paper feed station which has been specified by User Parameter Switch 0F (15), or which is used for the Specified Cassette Selection feature.

1

2nd paper feed station usage for fax printing

0: Enabled

1: Disabled

2

3rd paper feed station usage for fax printing

0: Enabled

1: Disabled

3

4th paper feed station usage for fax printing

0: Enabled

1: Disabled

4

LCT usage for fax printing 0: Enabled

1: Disabled

5-7

Not used

Do not change the settings.

Printer Switch 03 (SP No. 1-103-004)

No

Function

Comments

0: Incoming pages are printed without length

reduction.

Length reduction of received

(Page separation threshold: Printer Switch 03,

0

data

0: Disabled

bits 4 to 7)

1: Incoming page length is reduced when

1: Enabled

printing.

(Maximum reducible length: Printer Switches

04, bits 0 to 4)

1-3

Not used

Do not change the settings

Page separation threshold (with reduction

disabled with switch 03-0 above).

Page separation setting when

For example, if this setting is set to "10", and

4

sub scan compression is

A4 is the selected paper size:

to

forbidden

If the received document is 10 mm or less

7

00-0F (0-15 mm: Hex)

longer than A4, then the 10 mm are cut and

Default: 6 mm

only 1 page prints.

If the received document is 10 mm longer than

A4, then the document is split into 2 pages.

Printer Switch 04 (SP No. 1-103-005)

No

Function

Comments

0

to 4

Maximum reducible length when length reduction is enabled with switch 03-0 above.

[Maximum reducible length] = [Paper length] + (N x 5mm) "N" is the decimal value of the binary setting of bits 0 to 4.

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Setting

0

0

0

0

0

0 mm

0

0

0

0

1

5 mm

0

0

1

0

0

20 mm

1

1

1

1

1

155 mm

For A5 sideways and B5 sideways paper

[Maximum reducible length] = [Paper length] + 0.75 x (N x 5mm)

5

6

Length of the duplicated image on the next page, when page separation has taken place.

Bit 6

Bit 5

Setting

0

0

4 mm

0

1

10 mm

1

0

15 mm

1

1

Not used

7

Not used.

Do not change the setting.

Printer Switch 05 - Not used (do not change the settings)

Printer Switch 06 (SP No. 1-103-007)

No

Function

Comments

0

Printing while a paper cassette is pulled out, when the Just Size Printing feature is enabled.

0: Printing will not start

1: Printing will start if another cassette has a suitable size of paper, based on the paper size selection priority tables.

Cross reference

Just size printing on/off – User switch 05, bit 5

1-7

Not used.

Do not change the settings.

Printer Switch 07 (SP No. 1-103-008)

No

Function

Comments

0-3

Not used.

Do not change the settings.

4

List of destinations in the Communication Failure Report for broadcasting

0: All destinations

1: Only destinations where communication failure occurred

1: Only destinations where communication failure occurred are printed on the Communication Failure Report.

5-7

Not used.

Do not change the settings.

Printer Switch 08 - Not used (do not change the settings)

Printer Switch 09 - Not used (do not change the settings)

Printer Switch 0A - Not used (do not change the settings)

Printer Switch 0B - Not used (do not change the settings)

Printer Switch 0C - Not used (do not change the settings)

Printer Switch 0C - Not used (do not change the settings)

Printer Switch 0C - Not used (do not change the settings)

Printer Switch 0E (SP No. 1-103-015)

No

Function

Comments

0

Paper size selection priority 0: Width

1: Length

0: A paper size that has the same width as the received data is selected first.

1: A paper size which has enough length to print all the received lines without reduction is selected first.

1

Paper size selected for printing A4 width fax data

0: 8.5" x 11" size

1: A4 size

This switch determines which paper size is selected for printing A4 width fax data, when the machine has both A4 and 8.5" x 11" size paper.

2

Page separation 0: Enabled

1: Disabled

1: If all paper sizes in the machine require page separation to print a received fax message, the machine does not print the message (Substitute Reception is used). After a larger size of paper is set in a cassette, the machine automatically prints the fax message.

3-4

Printing the sample image on reports

"Same size" means the sample image is printed at 100%, even if page separation occurs.

User Parameter Switch 19 (13H) bit 4 must be set to "0" to enable this switch. Refer to Detailed Section Descriptions for more on this feature.

Bit 4

Bit 3

Setting

0

0

The upper half only

0

1

50% reduction (sub-scan only)

1

0

Same size

1

1

Not used

5-6

Not used

Do not change the settings.

Printer Switch 0E (SP No. 1-103-015)

No

Function

Comments

0

Paper size selection priority 0: Width

1: Length

0: A paper size that has the same width as the received data is selected first.

1: A paper size which has enough length to print all the received lines without reduction is selected first.

1

Paper size selected for printing A4 width fax data

0: 8.5" x 11" size

1: A4 size

This switch determines which paper size is selected for printing A4 width fax data, when the machine has both A4 and 8.5" x 11" size paper.

2

Page separation 0: Enabled

1: Disabled

1: If all paper sizes in the machine require page separation to print a received fax message, the machine does not print the message (Substitute Reception is used). After a larger size of paper is set in a cassette, the machine automatically prints the fax message.

3-4

Printing the sample image on reports

"Same size" means the sample image is printed at 100%, even if page separation occurs.

User Parameter Switch 19 (13H) bit 4 must be set to "0" to enable this switch. Refer to Detailed Section Descriptions for more on this feature.

Bit 4

Bit 3

Setting

0

0

The upper half only

0

1

50% reduction (sub-scan only)

1

0

Same size

1

1

Not used

5-6

Not used

Do not change the settings.

Printer Switch 0E (SP No. 1-103-015)

No

Function

Comments

0

Paper size selection priority 0: Width

1: Length

0: A paper size that has the same width as the received data is selected first.

1: A paper size which has enough length to print all the received lines without reduction is selected first.

1

Paper size selected for printing A4 width fax data

0: 8.5" x 11" size

1: A4 size

This switch determines which paper size is selected for printing A4 width fax data, when the machine has both A4 and 8.5" x 11" size paper.

2

Page separation 0: Enabled

1: Disabled

1: If all paper sizes in the machine require page separation to print a received fax message, the machine does not print the message (Substitute Reception is used). After a larger size of paper is set in a cassette, the machine automatically prints the fax message.

3-4

Printing the sample image on reports

"Same size" means the sample image is printed at 100%, even if page separation occurs.

User Parameter Switch 19 (13H) bit 4 must be set to "0" to enable this switch. Refer to Detailed Section Descriptions for more on this feature.

Bit 4

Bit 3

Setting

0

0

The upper half only

0

1

50% reduction (sub-scan only)

1

0

Same size

1

1

Not used

5-6

Not used

Do not change the settings.

0: When page separation has taken

Equalizing the reduction ratio among

place, all the pages are reduced with the

separated pages

same reduction ratio.

7

(Page Separation)

1: Only the last page is reduced to fit the

0: Enabled

selected paper size when page

1: Disabled

separation has taken place. Other pages

are printed without reduction.

Printer Switch 0F (SP No. 1-103-016)

No

Function

Comments

0-1

Smoothing feature

(0, 0) (0, 1): Disable smoothing if the machine receives halftone images from other manufacturers fax machines frequently.

Bit 1

Bit 0

Setting

0

0

Disabled

0

1

Disabled

1

0

Enabled

1

1

Not used

2

Duplex printing 0: Disabled

1: Enabled

1: The machine always prints received fax messages in duplex printing mode:

3

Binding direction for Duplex printing 0: Left binding

1: Top binding

0: Sets the binding for the left edge of the stack.

1: Sets the binding for the top of the stack.

4-7

Not used

Do not change the settings.