1001*

Leading Edge Registration

Adjusts the leading edge registration by changing the registration clutch operation timing.

001

Tray: Plain

[–9 to 9/ 0 / 0.1 mm step]

002

Tray: Thick 1

003

Tray: Thick 2

004

By-pass: Plain

005

By-pass: Thick 1

006

By-pass: Thick 2

007

Duplex: Plain

008

Duplex: Thick 1

1002*

Side-to-Side Registration

Adjusts the side to side registration by changing the laser main scan start position for each mode.

001

By-pass

[–4 to 4/ 0 / 0.1 mm step]

002

Tray 1

003

Tray 2

004

Tray 3

005

Tray 4

006

LCT

007

Duplex

1003*

Registration Buckle Adjustment

Adjusts the paper feed motor timing. Paper feed motor timing determines the amount of paper buckle at Registration. (A "+" setting causes more buckling.)

001

Tray 1: Plain

[-9 to 5 / -4 / 1 mm step]

002

Tray 1: Thick 1

003

Tray 1: Thick 2

004

Tray 2, 3, 4: Plain

005

Tray 2, 3, 4: Thick1

006

Tray 2, 3, 4: Thick2

007

By-pass: Plain

[-9 to 5 / -2 /1 mm step]

008

By-pass: Thick 1

009

By-pass: Thick 2

010

Duplex: Plain

[-9 to 5 / -4 / 1 mm step]

011

Duplex: Thick 1

[-9 to 5 / -3 / 1 mm step]

012

LCT: Plain

[-9 to 5 / -4 / 1 mm step]

013

LCT: Thick1

014

LCT: Thick2

1007*

By-pass Paper Size Detection

Controls paper size detection for the by-pass feed table.

001

Detection Timing

[-15 to 15 / 0 / 5 mm step]

002

LG Detection

[0 to 1 / 0 / 1]

0: LTSEF, 1: LG

1105*

Fusing Temperature Adjustment

Allows adjustment of the hot roller temperature at the center and ends of the roller for the quality or thickness of the paper. The hot roller in this machine has two fusing lamps: one heats the center of the roller, the other heats both ends. Each fusing lamp can be adjusted separately.

The "re-load temperature" is the "print ready temperature". When the fusing temperature exceeds this setting, the machine can operate. Do not set up a re-load temperature (Re-load Temp. = Fusing. Temp – SP Value.) that is higher than the SP1-105-2 setting.

001

Roller Center

C2b: [100 to 170 / 140 / 1 deg]

C2c: [100 to 170 / 150 / 1 deg]

Adjusts the fusing temperature at the center of the hot roller.

002

Roller Ends

C2b: [100 to 170 / 145 / 1 deg]

C2c: [100 to 170 / 155 / 1 deg]

Adjusts the fusing temperature at the ends of the hot roller.

003

Re-load Temp. Minus: Roller Center

[0 to 60 / 0 / 1 deg]

Sets the reload temperature for the center of the hot roller. This setting depends on the target temperature.

Reload temp. = Target Temp – This SP Setting

 Do not set a temperature that is higher than the setting for SP1105 1 (Roller Center: Trays)

004

Re-load Temp. Minus: Roller Ends

[0 to 60 / 0 / 1 deg]

Sets the reload temperature for the ends of the hot roller. This setting depends on the target temperature.

Reload temp. = Target Temp – This SP Setting

 Do not set a temperature that is higher than the setting for SP1105 2 (Roller Ends: Trays)

005 to

022

The following SPs adjust the fusing temperature at the center or ends of the hot roller for each paper type.

005

Roller Center: M-Thick

C2b: [100 to 170 / 145 / 1 deg]

C2c: [100 to 170 / 155 / 1 deg]

006

Roller Ends: M-Thick

C2b: [100 to 170 / 150 / 1 deg]

C2c: [100 to 170 / 160 / 1 deg]

007

Roller Center: Thick 1

[100 to 170 / 130 / 1 deg]

008

Roller Ends: Thick 1

009

Roller Center: Thick 2

[100 to 170 / 150/ 1 deg]

010

Wait Temp: Center Minus

011

Wait Temp: Ends Minus

C2b: [100 to 170 / 130 / 1 deg]

C2c: [100 to 170 / 140 / 1 deg]

012

Roller Ends: Thin

C2b: [100 to 170 / 135 / 1 deg]

C2c: [100 to 170 / 145 / 1 deg]

013

Roller Center: OHP: Plain

[100 to 170 / 150/ 1 deg]

014

Roller Ends: OHP: Plain

[100 to 170 / 155/ 1 deg]

015

Roller Center: OHP: Thick

016

Roller Ends: OHP: Thick

[100 to 170 / 160/ 1 deg]

017

Roller Center: Special 1

C2b: [100 to 170 / 140 / 1 deg]

C2c: [100 to 170 / 150 / 1 deg]

018

Roller Ends: Special 1

C2b: [100 to 170 / 145 / 1 deg]

C2c: [100 to 170 / 155 / 1 deg]

019

Roller Center: Special 2

C2b: [100 to 170 / 140 / 1 deg]

C2c: [100 to 170 / 150 / 1 deg]

020

Roller Ends: Special 2

C2b: [100 to 170 / 145 / 1 deg]

C2c: [100 to 170 / 155 / 1 deg]

021

Roller Center: Special 3

C2b: [100 to 170 / 140 / 1 deg]

C2c: [100 to 170 / 150 / 1 deg]

022

Roller Ends: Special 3

C2b: [100 to 170 / 145 / 1 deg]

C2c: [100 to 170 / 155 / 1 deg]

023

Feed Waiting: Plain

Turns the feed waiting mode on or off for each paper type.

[0 to 1 / 0 / 1] 0=Off, 1=On

The paper waits at the registration roller until the fusing temperature reaches the prescribed temperature (adjustable with SP1105-028 to -37).

If you enable this feature, also set SP 1105-38 to a convenient value for the customer.

024

Feed Waiting: M-Thick

025

Feed Waiting: Thick 1

026

Feed Waiting: Thick 2

027

Feed Waiting: Thin

028

Feed Wait: Center Minus: Plain

Adjusts the offset value for each re-load temperature to exit the feed waiting mode.

[0 to 60 / 0 / 1 deg]

029

Feed Wait: Ends Minus: Plain

030

Feed Wait: Center Minus: M-Thick

031

Feed Wait: Ends Minus: M-Thick

032

Feed Wait: Center Minus: Thick 1

033

Feed Wait: Ends Minus: Thick 1

034

Feed Wait: Center Minus: Thick 2

035

Feed Wait: Ends Minus: Thick 2

036

Feed Wait: Center Minus: Thin

037

Feed Wait: Ends Minus: Thin

038

Feed Waiting: Maximum Time

Sets the maximum feed waiting time. [0 to 30 / 0 / 1 sec]

The paper is fed when the time specified with this SP has passed even though the fusing temperature has not reached the prescribed temperature.

0: Disabled.

1106

Fusing Temperature Display

001

Roller Center

Displays the temperature of the fusing unit.

[-20 to 250 / 0 / 1 deg]

002

Roller Ends

003

Machine Inside at Power On

Displays the temperature inside the machine.

[-20 to 250 / 0 / 1 deg]

004

Machine Inside

1801*

MotorSpeedAdjust

Adjusts the speeds of each motor. Each step decreases or increases motor speed in 0.05% increments

Regist: Registration motor, Feed: Feed motor,

Duplex: Duplex/By-pass motor, Inverter: Duplex inverter motor, Exit: Paper exit motor, Bridge: Bridge unit drive motor,

OpcMot: Drum motor, TransferMot: Transfer/Development Motor, FusingMot: Fusing motor,

DevPuddleMot: Development Paddle motor

001

Regist: 90: Thick 2

[-2 to 2 / 0.4 / 0.05 %]

002

Regist: 154: Thick 1

003

Regist: 180: Plain

004

Regist: 230: Plain

005

Feed: 90: Thick 2

[-2 to 2 / -0.4 / 0.05 %]

006

Feed: 154: Thick 1

007

Feed: 180: Plain

[-2 to 2 / -1 / 0.05 %]

008

Feed: 230: Plain

009

Duplex_CW: 90: Thick 2

[-4 to 4 / 0.4 / 0.1 %]

010

Duplex_CW: 154: Thick 1

011

Duplex_CW: 180: Plain

[-4 to 4 / -2.3 / 0.1 %]

012

Duplex_CW: 230: Plain

013

Duplex_CCW: 90: Thick 2

[-4 to 4 / 0.4 / 0.1 %]

014

Duplex_CCW: 154: Thick 1

015

Duplex_CCW: 180: Plain

[-4 to 4 / -0.2 / 0.1 %]

016

Duplex_CCW: 230: Plain

017

Inverter_CW: 90: Thick 2

[-4 to 4 / 0 / 0.1 %]

018

Inverter_CW: 154: Thick 1

019

Inverter_CW: 180: Plain

020

Inverter_CW: 230: Plain

021

Inverter_CCW: 90: Thick 2

022

Inverter_CCW: 154: Thick 1

023

Inverter_CCW: 180: Plain

024

Inverter_CCW: 230: Plain

025

Exit_CW: 90: Thick 2

026

Exit_CW: 154: Thick 1

027

Exit_CW: 180: Plain

028

Exit_CW: 230: Plain

029

Bridge: 90: Thick 2

030

Bridge: 154: Thick 1

031

Bridge: 180: Plain

032

Bridge: 230: Plain

033

OpcMot:90

[-4 to 4 / 0 / 0.01 %]

034

OpcMot:154

035

OpcMot:180

036

OpcMot:230

037

TransferMot:90

038

TransferMot:154

039

TransferMot:180

040

TransferMot:230

041

FusingMot:90

042

FusingMot:154

043

FusingMot:180

044

FusingMot:230

045

DevPuddleMot

[-4 to 4 / 0 / 0.1 %]

1902*

Cleaning Web Setting

001

Web Consumption

[0 to 120 / 0 / 1 %]

Displays the consumed amount of the web roll.

002

Web Motor Interval

C2b: [3 to 130 / 8.4 / 0.1 sec]

C2c: [3 to 130 / 6.7 / 0.1 sec]

Adjusts the interval for web motor rotation.

003

Web Motor Time

[0.3 to 10 / 4.2 / 0.1 sec]

Adjusts the rotation time of the web motor.

004

Web Near End Setting

C2b: EU [0 to 100 / 90 / 1 %]

C2b: ASIA/NA [0 to 100 / 92 / 1 %]

C2c: EU [0 to 100 / 90 / 1 %]

C2c: ASIA/NA [0 to 100 / 92 / 1 %]

Adjusts the threshold for web near end.

005

Web Motor Interval: Thick 1

[3 to 130 / 11.2 / 0.1 sec]

Adjusts the interval for web motor rotation (thick 1).

006

Web Motor Interval: Thick 2

[3 to 130 / 16.8 / 0.1 sec]

Adjusts the interval for web motor rotation (thick 2).

007

Paper Interval Time

[0 to 10 / 5 / 1 sec]

Adjusts the threshold for paper feeding. When the time between trailing edge detection and leading edge detection is within the value of this setting, the machine determines that the paper is still being fed.

008

Web Motor Setting: Web End

[0 to 60 / 27 / 1 sec]

Adjusts the motor rotation time after the web end.

009

Web Motor Rotation: Power On

[0 to 10 / 0 / 1 times]

Adjusts the number of web motor rotations at the re-load state.

010

Web Motor Interval: Pre-idle

[0 to 30 / 0 / 1 sec]

Adjusts the motor waiting time after the fusing motor idling.

011

Web Motor Rotation: Pre-idle

[0 to 10 / 0 / 1 times]

Adjusts the number of web motor rotations at the fusing idling state.

1950*

Tray Lock at Jam

[0 or 1 / 0 / 1 ] 0= OFF, 1= ON

Not used