REPLACEMENT AND ADJUSTMENT Savin MP C3003, Ricoh MP C3003 Service Manual

HOME PAGE | < Previous | Contents | Next >

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1. REPLACEMENT AND ADJUSTMENT

1.1 INNER FINISHER

1. Interface cable [A]

2. Open the front cover [A]

3. Upper left cover [A] ×1)

4. Left rear cover [A] ×2)

Inner Finisher

5. Finisher [A] ×1)

6.

Finisher Front Cover

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.2 FINISHER FRONT COVER

1. Pull the finisher [A]

2. Finisher front cover [A] ×2)

Finisher Upper Cover

1.3 FINISHER UPPER COVER

1. Finisher page 1 "Inner Finisher")

2. Finisher front cover page 3 )

3. Finisher upper cover [A] ×2)

Paper exit tray

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.4 PAPER EXIT TRAY

1. Finisher front cover page 3 )

2. Left lower cover [A] ×2)

3.

Paper Exit Cover

1.5 PAPER EXIT COVER

1. Paper exit tray page 5)

2. Paper exit cover [A] ×3,×3,×2)

Control Board

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.6 CONTROL BOARD

 When a control board is replaced, use the same DIP switch settings as those of the control board before replacement.

1. Finisher front cover page 3 )

2. Control board [A] ×3, ×17)

Entrance Sensor

1.7 ENTRANCE SENSOR

1. Finisher page 1 "Inner Finisher")

2. Open/Close upper cover [A] ×2)

3. Entrance sensor unit [A] ×1, ×1)

Entrance Sensor

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

4. Entrance sensor [A]

Entrance Motor

1.8 ENTRANCE MOTOR

1. Finisher page 1 "Inner Finisher" )

2. Finisher right rear bracket [A] ×2)

3. Finisher rear cover [A] ×2)

4. Entrance motor [A] ×2, ×1)

Tray Lift Motor

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.9 TRAY LIFT MOTOR

1. Paper exit tray page 5)

2. Tray lift motor unit [A] ×2, ×1, ×1)

3.

4. Tray lift motor [A] ×2)

Paper Exit Full Sensor

1.10 PAPER EXIT FULL SENSOR

1. Paper exit tray page 5)

2. Paper exit full sensor [A] ×1, ×1)

Paper Bail Home Position Sensor

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.11 PAPER BAIL HOME POSITION SENSOR

1. Paper exit cover page 6)

2. Paper bail home position sensor [A]

Paper Surface Detection Sensor

1.12 PAPER SURFACE DETECTION SENSOR

1. Paper exit cover page 6)

2. Paper surface detection sensor [A]

Paper Bail Motor

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.13 PAPER BAIL MOTOR

1. Paper exit page 6)

2. Paper bail motor [A] ×2, ×1)

Transport Sensor

1.14 TRANSPORT SENSOR

1. Upper cover page 4 "Finisher Upper Cover" )

2. Transport sensor unit [A] ×1, ×1, ×1)

3. Transport sensor [A]

Strike Roller Home Position Sensor

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.15 STRIKE ROLLER HOME POSITION SENSOR

1. Upper cover page 4 "Finisher Upper Cover" )

2. Rear cover page 10 "Entrance Motor" )

3. Rotate the timing belt [A], and release the strike roller arm unit [B] from the strike roller HP sensor [C].

4. Strike roller home position sensor unit [A] ×1, ×1, ×1)

Strike Roller Home Position Sensor

5. Strike roller home position sensor [A]

Paper Exit Guide Plate Motor

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.16 PAPER EXIT GUIDE PLATE MOTOR

1. Control board page 7 )

2. Paper exit guide plate motor [A] ×2, ×1, ×3)

Paper Exit Guide Plate Home Position Sensor

1.17 PAPER EXIT GUIDE PLATE HOME POSITION SENSOR

1. Control board page 7 )

2. Rotate the paper output guide plate gear [A] counterclockwise, and release the paper output guide plate [B] from the paper output guide plate HP sensor [C].

3. Paper exit guide plate home position sensor [A] ×1)

Strike Roller Motor

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.18 STRIKE ROLLER MOTOR

1. Paper exit cover page 6 )

2. Rear cover page 10 "Entrance Motor" )

3. Rear rail [A] ×2)

4. Strike roller motor [A] ×2, ×1)

Shift Motor

1.19 SHIFT MOTOR

 After attaching, rotate the knob, and check that all gear trains can rotate.

 After attachment, when the cam is rotated, check that the link interlocks.

1. Open/Close upper cover page 4 "Finisher Upper Cover")

2. Control board bracket page 7 "Control Board")

3. Pulley [A], Timing belt [B] ×1)

4. Shift motor unit [A] ×2, ×1, ×1)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

Shift Motor

5. Shift motor [A] ×2)

Shift Roller Home Position Sensor

1.20 SHIFT ROLLER HOME POSITION SENSOR

1. Control board bracket page 7 "Control Board" )

2. Shift roller home position sensor unit [A] ×1, ×2, ×1)

3. Shift roller home position sensor [A]

Stapler Home Position Sensor

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.21 STAPLER HOME POSITION SENSOR

1. Control board bracket page 7 "Control Board" )

2. Open/Close upper cover page 4 "Finisher Upper Cover" )

3. Knob [A]

4.

5. Stapler home position sensor unit [A] ×1, ×1)

Stapler Home Position Sensor

6. Stapler home position sensor [A]

 If it is difficult to remove and attach, insert the stapler unit into the rear.

Stapler Displacement Motor

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.22 STAPLER DISPLACEMENT MOTOR

 When the finisher is inverted, be careful not to deform the frame.

1. Paper exit cover page 6 )

2. Clamps (4)

3. Upside down.

4. Base cover [A] ×3)

Stapler Displacement Motor

5. Stapler displacement motor ×2, ×1)

Stapler Unit

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.23 STAPLER UNIT

1. Control board bracket page 7 "Control Board")

2. Insert the stapler unit [A] into the rear.

3. Rear end reference fence [A] ×2)

4. Entrance cover page 25 "Stapler Home Position Sensor" )

5. Cover open/close switch unit [A] ×1, ×2)

6. Harness guide unit [A] ×1)

Stapler Unit

7. Move the stapler unit to the front, and remove the cartridge [A].

 During installation, install the cartridge last.

8. Remove the unit fixing screw of the stapler unit ×1)

Stapler Unit

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

9. Stapler unit [A] ×1, ×2)

Jogger Fence Motor (Front / Rear)

1.24 JOGGER FENCE MOTOR (FRONT / REAR)

1. Base cover page 27 "Stapler Displacement Motor")

2. Jogger fence motor (front) [A] ×2, ×1)

 During attachment, remove the jogger fence motor (rear) bracket [A], and check that the motor pulley has not separated from the timing belt.

Jogger Fence Motor (Front / Rear)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

3. Jogger fence motor (rear) [A] ×2, ×1)

 During attachment, check that the motor pulley has not separated from the timing belt.

Jogger Fence Home Position Sensor (Front)

1.25 JOGGER FENCE HOME POSITION SENSOR (FRONT)

1. Paper exit cover page 6)

2. Jogger fence home position sensor (front) unit [A] ×1, ×1, ×1)

3. Jogger fence home position sensor (front) [A]

Jogger Fence Home Position Sensor (Rear)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.26 JOGGER FENCE HOME POSITION SENSOR (REAR)

1. Paper exit cover page 6)

2. Jogger fence home position sensor (rear) unit [A] ×1, ×1)

3. Jogger fence home position sensor (rear) [A]

Stapler Tray Jam Detection Sensor

1.27 STAPLER TRAY JAM DETECTION SENSOR

1. Paper exit cover page 6 )

2. Paper exit roller unit [A] ×1)

3. Stapler tray jam detection sensor unit [A] ×1, ×1, ×1)

4. Stapler tray jam detection sensor [A]

Paper Detection Sensor

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.28 PAPER DETECTION SENSOR

1. Jogger fence motor (rear) page 32 )

2. Jogger fence motor (rear) bracket [A] ×2, ×3)

3. Paper detection sensor unit [A] ×2, ×1,×1)

Paper Detection Sensor

4. Paper detection sensor [A]

 During attachment, stop the sensor actuator from being caught.

Paper Exit Motor (Front)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

1.29 PAPER EXIT MOTOR (FRONT)

1. Paper exit cover page 6 )

2. Control board page 7 )

3. Rear cover page 10 "Entrance Motor" )

4. Pulley [A], Timing belt [B]

5. Paper exit motor (front) [A] ×2, ×1, ×2)

Paper Exit Motor (Rear)

1.30 PAPER EXIT MOTOR (REAR)

1. Paper exit motor (front) page 39 )

2. Control board bracket page 7 "Control Board") 3. Gear [A] ×1)

4. Clip ring [A] (2), Shaft bracket [B]

5. Remove the fan, fan defeat ×2)

Paper Exit Motor (Rear)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

INTERNAL FINISHER SR3130 (D690)

6. Paper exit motor (rear) [A] ×2, ×1)

< Previous | Contents | Next >