6006

[ADF Adjustment]

001

Side-to-Side Regist: Front

*ENG

[-3.0 to 3.0 / 0.0 / 0.1 mm/step]

Adjusts front side main scan register for ADF.

002

Side-to-Side Regist: Rear

*ENG

[-3.0 to 3.0 / 0.0 / 0.1 mm/step]

Adjusts rear side main scan register for ADF.

003

Leading Edge Registration

*ENG

[-5.0 to 5.0 / 0.0 / 0.1 mm/step]

Adjusts DFGATE assert timing.

 Value increase: Delays DFGATE assert timing.

 Value decrease: Delays DFGATE assert timing.

005

Buckle: Duplex Front

*ENG

[-5.0 to 5.0 / 0.0 / 0.1 mm/step]

Adjusts front side buckle amount (skew correct amount).

 Value increase: increases front side buckle amount.

 Value decrease: decreases front side buckle amount.

006

Buckle: Duplex Rear

*ENG

[-5.0 to 5.0 / 0.0 / 0.1 mm/step]

Adjusts rear side buckle amount (skew correct amount).

 Value increase: increases rear side buckle amount.

 Value decrease: decreases rear side buckle amount.

007

Rear Edge Erase

*ENG

[-10.0 to 10.0 / 0.0 / 0.1 mm/step]

Adjusts DFGATE negate timing.

 Value increase: Delays DFGATE negate timing.

 Value decrease: Delays DFGATE negate timing. (Direction for erasing trailing edge of original)

010

L-Edge Regist (1-Pass): Front

*ENG

[-5.0 to 5.0 / 0.0 / 0.1 mm/step]

For 1 path simultaneous duplex models only. Adjusts the front side sheet through register. Adjusts to max. value in the adjustment range, when set value is larger than adjust range. When finishing setting without defining, remains as the last set value.

011

L-Edge Regist (1-Pass): Rear

*ENG

[-5.0 to 5.0 / 0.0 / 0.1 mm/step]

For 1 path simultaneous duplex models only. Adjusts the rear side sheet through register. Adjusts to max. value in the adjustment range, when set value is larger than adjust range. When finishing setting without defining, remains as the last set value.

012

1st Buckle (1-Pass)

*ENG

[-3.0 to 3.0 / 0.0 / 0.1 mm/step]

For 1 path simultaneous duplex models only. Adjusts pull out roller buckle amount. Adjusts to max. value in the adjustment range, when set value is larger than adjust range. When finishing setting without defining, remains as the last set value.

013

2nd Buckle (1-Pass)

*ENG

[-2.0 to 3.0 / 0.0 / 0.1 mm/step]

For 1 path simultaneous duplex models only. Adjusts scanning entrance roller buckle amount. Adjusts to max. value in the adjustment range, when set value is larger than adjust range. When finishing setting without defining, remains as the last set value.

014

T-Edge Erase (1-Pass): Front

*ENG

[-5.0 to 5.0 / -1.5 / 0.1 mm/step]

For 1 path simultaneous duplex models only. Adjusts the front side trailing edge register.

 Value increase: add trailing edge to image.

 Value decrease: erases trailing edge of image.

Adjusts to max. value in the adjustment range, when set value is larger than adjust range. When finishing setting without defining, remains as the last set value. Sets initial setting to -1.5mm instead of 0mm considering originals shadow.

015

T-Edge Erase (1-Pass): Rear

*ENG

[-5.0 to 5.0 / -1.5 / 0.1 mm/step]

For 1 path simultaneous duplex models only. Adjusts the rear side trailing edge register.

 Value increase: add trailing edge to image.

 Value decrease: erases trailing edge of image.

Adjusts to max. value in the adjustment range, when set value is larger than adjust range. When finishing setting without defining, remains as the last set value. Sets initial setting to -1.5mm instead of 0mm considering originals shadow.

6007

[ADF INPUT Check]

See page 3-1

6008

[ADF OUTPUT Check]

See page 3-31

6009

[ADF FreeRun]

001

Free Run Simplex Motion

ENG

[0 or 1 / 0 / 1/step]

Runs simplex free run when setting original to ADF.

002

Free Run Duplex Motion

ENG

[0 or 1 / 0 / 1/step]

Runs duplex free run when setting original to ADF.

003

Free Run Stamp Motion

ENG

[0 or 1 / 0 / 1/step]

Runs simplex free run (with DONE stamp) when setting original to ADF.

004

Free Run Simplex Motion(low speed)

ENG

[0 or 1 / 0 / 1/step]

Runs paper existing simplex free run of ADF in low line speed.

005

Free Run Simplex Motion(high speed)

ENG

[0 or 1 / 0 / 1/step]

Runs paper existing simplex free run of ADF in low line speed.

006

Free Run Duplex Motion(low speed)

ENG

[0 or 1 / 0 / 1/step]

Runs paper existing duplex free run of ADF in high line speed.

007

Free Run Duplex Motion(high speed)

ENG

[0 or 1 / 0 / 1/step]

Runs paper existing duplex free run of ADF in high line speed.

006

Free Run Duplex Motion(low speed)

ENG

[0 or 1 / 0 / 1/step]

Runs paper existing duplex free run of ADF in high line speed.

007

Free Run Duplex Motion(high speed)

ENG

[0 or 1 / 0 / 1/step]

Runs paper existing duplex free run of ADF in high line speed.

006

Free Run Duplex Motion(low speed)

ENG

[0 or 1 / 0 / 1/step]

Runs paper existing duplex free run of ADF in high line speed.

007

Free Run Duplex Motion(high speed)

ENG

[0 or 1 / 0 / 1/step]

Runs paper existing duplex free run of ADF in high line speed.

6010

[Stamp Position Adj.]

Adjusts stamping position of DONE stamp.

 Value increase: Moves stamping position of DONE stamp towards original trailing edge.

 Value decrease: Moves stamping position of DONE stamp towards original leading edge.

001

-

*ENG

[-5.0 to 5.0 / 0.0 / 0.1 mm/step]

6010

[Stamp Position Adj.]

Adjusts stamping position of DONE stamp.

 Value increase: Moves stamping position of DONE stamp towards original trailing edge.

 Value decrease: Moves stamping position of DONE stamp towards original leading edge.

001

-

*ENG

[-5.0 to 5.0 / 0.0 / 0.1 mm/step]

6010

[Stamp Position Adj.]

Adjusts stamping position of DONE stamp.

 Value increase: Moves stamping position of DONE stamp towards original trailing edge.

 Value decrease: Moves stamping position of DONE stamp towards original leading edge.

001

-

*ENG

[-5.0 to 5.0 / 0.0 / 0.1 mm/step]

6011

[1-Pass ADF INPUT Check]

See page 3-1

6012

[1-Pass ADF OUTPUT Check]

See page 3-31

6016

[Original Size Detect Setting]

Sets to judge as witch original size for two original sizes that can not be judged with ADF. Size of each bit is different depending on region. Set corresponding bit to "0" when to prior the default size. Set "1" to let the switching size judge.

001

-

*ENG

[0 to 255 / 0 / 1/step]

6017

[DF Magnification Adj.]

Fine-tunes scale error. Changes line speed corresponding to scale rate setting value.

001

-

*ENG

[-5.0 to 5.0 / 0.0 / 0.1 %/step]

6020

[Skew Correction Moving Setting]

With default setting, original buckling (Skew correct 2) to ADF scanning entrance roller is only done for small sizes (B6, A5, HLT). With setting "1", this buckling can be done to all sizes.

001

-

*ENG

[0 or 1 / 0 / 1/step]

6100

[Sub-scanPunchPosAdj:2K/3K FIN]

 Adjusts position of carry direction (sub scan direction) for punch. Adjusting value to -: hole position moves toward trailing edge of paper when intaking.

 Adjusting value to +: hole position moves toward leading edge of paper when intaking.

001

JPN/EU: 2-Hole

ENG

[-7.5 to 7.5 / 0.0 / 0.5mm/step]

002

NA: 3-Hole

ENG

003

Europe: 4-Hole

ENG

004

NEU: 4-Hole

ENG

005

NA: 2-Hole

ENG

6101

[Main-scanPunchPosAdj:2K/3K FIN]

Adjusts position of width direction (main scan direction) for punch.

 Adjusting value to -: hole position moves toward front side of machine.

 Adjusting value to +: hole position moves toward rear side of machine.

001

JPN/EU: 2-Hole

ENG

[-2.0 to 2.0 / 0.0 / 0.4mm/step]

002

NA: 3-Hole

ENG

003

Europe: 4-Hole

ENG

004

NEU: 4-Hole

ENG

005

NA: 2-Hole

ENG

6102

[SkewCorrectBuckleAdj:2K/3K FIN]

Adjusts the skew correction bending amount when punching specified paper.

 Adjusts value to -: buckling amount decreases

 Adjusts value to +:buckling amount increases.

001

A3 SEF

ENG

[-5.0 to 5.0 / 0.0 / 0.2mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

006

B5 LEF

ENG

[-5.0 to 5.0 / 0.0 / 0.2mm/step]

007

A5 LEF

ENG

008

DLT SEF

ENG

009

LG SEF

ENG

010

LT SEF

ENG

011

LT LEF

ENG

[-5.0 to 5.0 / 0.0 / 0.2mm/step]

012

HLT LEF

ENG

013

12"x18"

ENG

014

8K SEF

ENG

015

16K SEF

ENG

016

16K LEF

ENG

017

Other

ENG

[-5.0 to 5.0 / 0.0 / 0.2mm/step]

Adjusts the skew correction bending amount when punching except the specified paper.

 Adjusts value to -: buckling amount decreases

 Adjusts value to +:buckling amount increases.

6103

[SkewCorrectCtrlSW:2K/3K FIN]

Switches way to control (Still buckling 0: enable / 1: disable) skew correction when punching specified paper.

001

A3 SEF

ENG

[0 or 1 / 0 / 1/step] 0: With Buckle Adj

1: Without Buckle Adj

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

006

B5 LEF

ENG

[0 or 1 / 0 / 1/step] 0: With Buckle Adj

1: Without Buckle Adj

007

A5 LEF

ENG

008

DLT SEF

ENG

009

LG SEF

ENG

010

LT SEF

ENG

011

LT LEF

ENG

[0 or 1 / 0 / 1/step] 0: With Buckle Adj

1: Without Buckle Adj

012

HLT LEF

ENG

013

12"x18"

ENG

014

8K SEF

ENG

015

16K SEF

ENG

016

16K LEF

ENG

[0 or 1 / 0 / 1/step] 0: With Buckle Adj

1: Without Buckle Adj

017

Other

ENG

Switches way to control (Still buckling 0: enable / 1: disable) skew correction when punching except the specified paper.

6104

[ShiftTrayJogPosAdj:2K/3K FIN]

Adjusts position for moving direction (main scan direction) of setting unit jogger when sending through specified paper.

 Adjusts value to -: move towards setting jogger width is tighter than base value.

 Adjusts value to +: move towards setting jogger width is wider than base value.

* Not use: currently, VOLGA-B does not have setting jogger in system configuration.

001

A3 SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 LEF

ENG

006

A5 LEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

011

HLT LEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

012

8K SEF

ENG

013

16K LEF

ENG

014

Other

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

Adjusts position for moving direction (main scan direction) of setting unit jogger when sending through except the specified paper.

 Adjusts value to -: move towards setting jogger width is tighter than base value.

 Adjusts value to +: move towards setting jogger width is wider than base value.

* Not use: currently, VOLGA-B does not have setting jogger in system configuration.

6105

[ShftTJogRtrctAngAdj:2K/3K FIN]

Adjusts the setting jogger retract angel when passing through specified paper.

 Adjusts value to +: towards up

 Adjusts value to -: towards down

* Not use: currently, VOLGA-B does not have setting jogger in system configuration.

001

A3 SEF

ENG

[-10 to 10 / 0 / 5deg/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

DLT SEF

ENG

005

LG SEF

ENG

006

LT SEF

ENG

007

8K SEF

ENG

008

Other

ENG

[-10 to 10 / 0 / 5deg/step]

Adjusts the setting jogger retract angel when passing through except the specified paper.

 Adjusts value to +: towards up

 Adjusts value to -: towards down

* Not use: currently, VOLGA-B does not have setting jogger in system configuration.

6106

[Use Paper Jogger: 2K/3K FIN]

Decides whether to use the setting jogger when passing through specified paper. The setting jogger won't be used when selecting 1.

* Not use: currently, VOLGA-B does not have setting jogger in system configuration.

001

A3 SEF

ENG

[0 or 1 / 0 / 1/step]

0: Jogging On

1: Jogging Off

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 LEF

ENG

[0 or 1 / 0 / 1/step]

0: Jogging On

1: Jogging Off

006

A5 LEF

ENG

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

[0 or 1 / 0 / 1/step]

0: Jogging On

1: Jogging Off

011

HLT LEF

ENG

012

8K SEF

ENG

013

16K LEF

ENG

014

Other

ENG

[0 or 1 / 0 / 1/step]

0: Jogging On

1: Jogging Off

Decides whether to use the setting jogger when passing through except the specified paper. The setting jogger won't be used when selecting 1. * Not use: currently, VOLGA-B does not have setting jogger in system configuration.

6107

[JogPosAdj(CrnrStplr):2K/3K FIN]

Adjusts width (main scan direction) of edge stitch when running specified paper conformity.

 Adjusts value to -: move towards jogger width is tighter than base value.

 Adjusts value to +: move towards jogger width is wider than base value.

001

A3 SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

006

B5 LEF

ENG

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

011

8K SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

012

16K SEF

ENG

013

16K LEF

ENG

014

Other

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

Adjusts width (main scan direction) of edge stitch jogger when running conformity to except the specified paper.

 Adjusts value to -: move towards jogger width is tighter than base value.

 Adjusts value to +: move towards jogger width is wider than base value.

6108

[JogPosAdj(BookStplr):2K/3K FIN]

Adjusts width (main scan direction) of saddle stitch when running specified paper conformity.

 Adjusts value to -: move towards jogger width is tighter than base value.

 Adjusts value to +: move towards jogger width is wider than base value.

001

A3 SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

B5 SEF

ENG

005

DLT SEF

ENG

006

LG SEF

ENG

007

LT SEF

ENG

008

12"x18"

ENG

009

8K SEF

ENG

010

Other

ENG

6109

[CrnrStplrJogTimeAdj:2K/3K FIN]

Adjusts jogging count of edge stitch jogger fence when running specified paper conformity (only last sheet).

001

A3 SEF

*ENG

[0 to 2 / 0 / 1time/step]

002

B4 SEF

*ENG

003

A4 SEF

*ENG

004

A4 LEF

*ENG

005

B5 SEF

*ENG

[0 to 2 / 0 / 1time/step]

006

B5 LEF

*ENG

007

DLT SEF

*ENG

008

LG SEF

*ENG

009

LT SEF

*ENG

010

LT LEF

*ENG

011

8K SEF

*ENG

[0 to 2 / 0 / 1time/step]

012

16K SEF

*ENG

013

16K LEF

*ENG

014

Other

*ENG

[0 to 2 / 0 / 1time/step]

Adjusts jogging count of edge stitch jogger fence running conformity to except the specified paper (only last sheet).

6110

[BookStplrJogTimeAdj:2K/3K FIN]

Adjusts jogging count of saddle stitch jogger fence when running specified paper conformity (only last sheet).

001

A3 SEF

ENG

[0 to 2 / 0 / 1time/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

B5 SEF

ENG

005

DLT SEF

ENG

[0 to 2 / 0 / 1time/step]

006

LG SEF

ENG

007

LT SEF

ENG

008

12"x18"

ENG

009

8K SEF

ENG

010

Other

ENG

[0 to 2 / 0 / 1time/step]

Adjusts jogging count of saddle stitch jogger fence running conformity to except the specified paper (only last sheet).

6111

[Staple Position Adj: 2K/3K FIN]

Adjusts staple position (main scan direction) for 2K / 3K / FIN of specified paper. Adjusting value to -: staple position moves toward front side of machine.

Adjusting value to +: staple position moves toward rear side of machine.

001

A3 SEF

ENG

[-3.5 to 3.5 / 0.0 / 0.5mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

[-3.5 to 3.5 / 0.0 / 0.5mm/step]

006

B5 LEF

ENG

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

011

8K SEF

ENG

[-3.5 to 3.5 / 0.0 / 0.5mm/step]

012

16K SEF

ENG

013

16K LEF

ENG

014

Other

ENG

[-3.5 to 3.5 / 0.0 / 0.5mm/step]

Adjusts staple position (main scan direction) for the near side parallel stitch/ far side parallel stitch / far side oblique stitch of paper except the specified paper.

 Adjusting value to -: staple position moves toward front side of machine.

 Adjusting value to +: staple position moves toward rear side of machine.

6112

[BookletStaplerPosAdj:2K/3K FIN]

Adjusts saddle stitch staple position (sub scan direction) of specified paper.

 Adjusting value to -: staple position moves toward trailing edge of paper when intaking.

 Adjusting value to +: staple position moves toward leading edge of paper when intaking.

001

A3 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

002

B4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

003

A4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

004

B5 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

005

DLT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

006

LG SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

007

LT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

008

12"x18"

ENG

[-1.8 to 1.8 / 0.0 / 0.2mm/step]

009

8K SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

010

Other

ENG

[-1.8 to 1.8 / 0.0 / 0.2mm/step]

Adjusts saddle stitch staple position (sub scan direction) of except the specified paper.

 Adjusting value to -: staple position moves toward trailing edge of paper when intaking.

 Adjusting value to +: staple position moves toward leading edge of paper when intaking.

6113

[BookletFolderPosAdj:2K/3K FIN]

Adjusts saddle stitch folding position (sub scan direction) of specified paper.

 Adjusting value to -: folding position moves toward trailing edge of paper when intaking.

 Adjusting value to +: folding position moves toward leading edge of paper when intaking.

001

A3 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

002

B4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

003

A4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

004

B5 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

005

DLT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

006

LG SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

007

LT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

008

12"x18"

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

009

8K SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

010

Other

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

Adjusts saddle stitch folding position (sub scan direction) of except the specified paper.

 Adjusting value to -: folding position moves toward trailing edge of paper when intaking.

 Adjusting value to +: folding position moves toward leading edge of paper when intaking.

6114

[Fold Speed Adj.: 2K/3K FIN]

Adjusts folding speed (extra folding time) of saddle stitch for specified paper. Adjust value: 0 (Standard)

Adjust value: 1 (Middle speed: standard+2.6[sec] Adjust value: 2 (Low speed: standard+5.2[sec])

001

A3 SEF

ENG

[0 to 2 / 0 / 1/step]

002

B4 SEF

ENG

[0 to 2 / 0 / 1/step]

003

A4 SEF

ENG

[0 to 2 / 0 / 1/step]

004

B5 SEF

ENG

[0 to 2 / 0 / 1/step]

005

DLT SEF

ENG

[0 to 2 / 0 / 1/step]

006

LG SEF

ENG

[0 to 2 / 0 / 1/step]

007

LT SEF

ENG

[0 to 2 / 0 / 1/step]

008

12"x18"

ENG

[0 to 2 / 0 / 1/step]

009

8K SEF

ENG

[0 to 2 / 0 / 1/step]

010

Other

ENG

[0 to 2 / 0 / 1/step]

Adjusts folding speed (extra folding time) of saddle stitch for except the specified paper.

Adjust value: 0 (Standard)

Adjust value: 1 (Middle speed: standard+2.6[sec] Adjust value: 2 (Low speed: standard+5.2[sec])

6115

[Finisher Free Run: 2K/3K FIN]

001

Free Run 1

ENG

[0 or 1 / 0 / 1/step]

Execute shift mode no paper free run.

002

Free Run 2

ENG

[0 or 1 / 0 / 1/step]

Execute edge stitch staple mode no paper free run.

003

Free Run 3

ENG

[0 or 1 / 0 / 1/step]

Execute saddle stitch staple mode no paper free run.

004

Free Run 4

ENG

[0 or 1 / 0 / 1/step]

Do not use with VOLGA-B.

6116

[CrnrStplrMxPrstkShAdj:2K/3KFIN]

Adjusts max pre-stack sheets count when edge stitching specified paper. Adjust value: 0; 1sheet pre-stack (standard)

Adjust value: -1; No pre-stack

001

A3 SEF

ENG

[-1 to 0 / 0 / 1sheet/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

[-1 to 0 / 0 / 1sheet/step]

006

B5 LEF

ENG

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

011

8K SEF

ENG

[-1 to 0 / 0 / 1sheet/step]

012

16K SEF

ENG

013

16K LEF

ENG

014

Other

ENG

[-1 to 0 / 0 / 1sheet/step]

Adjusts max pre-stock sheets count when edge stitching except the specified paper.

Adjust value: 0; 1sheet pre-stack (standard) Adjust value: -1; No pre-stack.

6117

[BookStplrMxPrstkShAdj:2K/3KFIN]

Adjusts max. pre-stock sheets count when saddle stitching specified paper. Adjust value: 0; 3 sheets pre-stack (standard)

Adjust value: -1; 2 sheets pre-stack

Adjust value: -2; 1 sheet pre-stack Adjust value: -3 to -7; no pre-stack.

001

A3 SEF

ENG

[-7 to 0 / 0 / 1sheet/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

B5 SEF

ENG

005

DLT SEF

ENG

[-7 to 0 / 0 / 1sheet/step]

006

LG SEF

ENG

007

LT SEF

ENG

008

12"x18"

ENG

009

8K SEF

ENG

010

Other

ENG

[-7 to 0 / 0 / 1sheet/step]

Adjusts max pre-stock sheets count when saddle stitching except the specified paper.

Adjust value: 0; 3 sheets pre-stack (standard) Adjust value: -1; 2 sheets pre-stack

Adjust value: -2; 1 sheet pre-stack, Adjust value: -3 to -7; no pre-stack.

6118

[CrnrStplrPrstkOffsAdj:2K/3KFIN]

Adjusts pre-stack offset amount (sub scan direction shearing amount of 1st and 2nd sheet) when edge stitching specified paper. Default offset is 20mm, when adjusting value to +, offset amount enlarges, when adjusting value to -, reduces.

001

A3 SEF

ENG

[-16 to 16 / 0 / 2mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

[-16 to 16 / 0 / 2mm/step]

006

B5 LEF

ENG

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

011

8K SEF

ENG

[-16 to 16 / 0 / 2mm/step]

012

16K SEF

ENG

013

16K LEF

ENG

014

Other

ENG

[-16 to 16 / 0 / 2mm/step]

Adjusts pre-stack offset amount (sub scan direction shearing amount of 1st and 2nd sheet) when edge stitching except the specified paper. Default offset is 20mm, when adjusting value to +, offset amount enlarges, when adjusting value to -, reduces.

6119

[BookStplrPrstkOffsAdj:2K/3KFIN]

Adjusts pre-stack offset amount (sub scan direction shearing amount of 1st and 2nd, 2nd and 3rd sheet) when saddle stitching specified paper. Default is No offset, when adjusting value to +, offset amount enlarges, when adjusting value to -, reduces.

001

A3 SEF

ENG

[-30 to 30 / 0 / 2mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

B5 SEF

ENG

005

DLT SEF

ENG

[-30 to 30 / 0 / 2mm/step]

006

LG SEF

ENG

007

LT SEF

ENG

008

12"x18"

ENG

009

8K SEF

ENG

010

Other

ENG

[-30 to 30 / 0 / 2mm/step]

Adjusts pre-stack offset amount (sub scan direction shearing amount of 1st and 2nd, 2nd and 3rd sheet) when saddle stitching except the specified paper.

Default is No offset, when adjusting value to +, offset amount enlarges, when adjusting value to -, reduces.

6120

[CrnStpPosExFeedAmtAdj:2K/3KFIN]

Adjusts over sending amount (sub scan direction) of positioning roller when edge stitching specified paper.

001

A3 SEF

ENG

[0 to 30 / 0 / 10mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

[0 to 30 / 0 / 10mm/step]

006

B5 LEF

ENG

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

011

8K SEF

ENG

[0 to 30 / 0 / 10mm/step]

012

16K SEF

ENG

013

16K LEF

ENG

014

Other

ENG

Adjusts over sending amount (sub scan direction) of positioning roller when edge stitching except the specified paper.

6122

[BkFoldJogSolMovAmtAdj:2K/3KFIN]

Adjusts move amount of saddle stitch conformity claw when saddle stitching specified paper.

 Adjusts value to +: towards up

 Adjusts value to -: towards down

001

A3 SEF

ENG

[-5 to 5 / 0 / 1mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

B5 SEF

ENG

005

DLT SEF

ENG

[-5 to 5 / 0 / 1mm/step]

006

LG SEF

ENG

007

LT SEF

ENG

008

12"x18"

ENG

009

8K SEF

ENG

010

Other

ENG

Adjusts move amount of saddle stitch conformity claw when saddle stitching except the specified paper.

 Adjusts value to +: towards up

 Adjusts value to -: towards down

6123

[INPUT Check: 2K/3K FIN]

See page 3-1

6124

[OUTPUT Check: 2K/3K FIN]

See page 3-31

6130

[Sub-scan PunchPosAdj:FrontFIN]

Adjusts position of carry direction (sub scan direction) for punch.

 Adjusting value to -: hole position moves toward trailing edge of paper when intaking.

 Adjusting value to +: hole position moves toward leading edge of paper when intaking.

001

Domestic 2Hole(Europe 2Hole)

*ENG

[-7.5 to 7.5 / 0.0 / 0.5mm/step]

002

North America 3Hole

*ENG

003

Europe 4Hole

*ENG

004

North Europe 4Hole

*ENG

005

North America 2Hole

*ENG

6131

[Main-scan PunchPosAdj:FrontFIN]

Adjusts position of width direction (main scan direction) for punch.

 Adjusting value to -: hole position moves toward front side of machine.

 Adjusting value to +: hole position moves toward rear side of machine.

001

Domestic 2Hole(Europe 2Hole)

*ENG

[-2.0 to 2.0 / 0.0 / 0.4mm/step]

002

North America 3Hole

*ENG

003

Europe 4Hole

*ENG

004

North Europe 4Hole

*ENG

005

North America 2Hole

*ENG

6132

[Jogger Fence Fine Adj:FrontFIN]

Adjusts width (main scan direction) of edge stitch jogger when running specified paper conformity.

 Adjusts value to -: move towards jogger width is tighter than base value.

 Adjusts value to +: move towards jogger width is wider than base value.

001

A3T

*ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

002

B4T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

003

A4T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

004

A4Y

*ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

005

B5T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

006

B5Y

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

007

DLT-T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

008

LG-T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

009

LT-T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

010

LT-Y

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

011

8K-T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

012

16K-T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

013

16K-Y

ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

014

Other

ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

010

LT-Y

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

011

8K-T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

012

16K-T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

013

16K-Y

ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

014

Other

ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

010

LT-Y

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

011

8K-T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

012

16K-T

*ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

013

16K-Y

ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

014

Other

ENG

[-3.0 to 3.0 / 0.0 / 0.5mm/step]

6133

[Staple Position Adj: FrontFIN]

Adjusts staple position (main scan direction) for the near side parallel stitch/ far side parallel stitch of specified paper.

 Adjusting value to -: staple position moves toward front side of machine.

 Adjusting value to +: staple position moves toward rear side of machine.

001

Finisher1

*ENG

[-2.0 to 2.0 / 0.0 / 0.5mm/step]

6133

[Staple Position Adj: FrontFIN]

Adjusts staple position (main scan direction) for the near side parallel stitch/ far side parallel stitch of specified paper.

 Adjusting value to -: staple position moves toward front side of machine.

 Adjusting value to +: staple position moves toward rear side of machine.

001

Finisher1

*ENG

[-2.0 to 2.0 / 0.0 / 0.5mm/step]

6133

[Staple Position Adj: FrontFIN]

Adjusts staple position (main scan direction) for the near side parallel stitch/ far side parallel stitch of specified paper.

 Adjusting value to -: staple position moves toward front side of machine.

 Adjusting value to +: staple position moves toward rear side of machine.

001

Finisher1

*ENG

[-2.0 to 2.0 / 0.0 / 0.5mm/step]

6134

[Finisher Free Run: FrontFIN]

001

Free Run1

*ENG

[0 or 1 / 0 / 1/step]

Execute shift mode no paper free run.

002

Free Run2

*ENG

[0 or 1 / 0 / 1/step]

Execute staple mode no paper free run.

003

Free Run3

*ENG

[0 or 1 / 0 / 1/step]

Tray package position move free run.

004

Free Run4

*ENG

[0 or 1 / 0 / 1/step]

Do not use with RUBICON-B.

6135

[INPUT Check: FrontFIN]

See page 3-1

6136

[OUTPUT Check: FrontFIN]

See page 3-31

6140

[Staple Position Adj: 1K FIN]

Adjusts staple position (main scan direction) for near side trailing edge parallel stitch / far side trailing edge parallel stitch.

 Adjusting value to -: staple position moves toward front side of machine.

 Adjusting value to +: staple position moves toward rear side of machine.

001

-

ENG

[-3.5 to 3.5 / 0.0 / 0.5mm/step]

6141

[Booklet Stapler Pos Adj:1K FIN]

Adjusts saddle stitch staple position (sub scan direction) of specified paper.

 Adjusting value to -: staple position moves toward trailing edge of paper when intaking.

 Adjusting value to +: folding position moves toward leading edge of paper when intaking.

001

A3 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

002

B4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

003

A4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

004

B5 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

005

DLT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

006

LG SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

007

LT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

008

12"x18"

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

6142

[Sub-scan Punch Pos Adj:1K FIN]

Adjusts position of carry direction (sub scan direction) for punch.

 Adjusting value to -: hole position moves toward trailing edge of paper when intaking.

 Adjusting value to +: hole position moves toward leading edge of paper when intaking.

001

JPN/EU: 2-Hole

ENG

[-7.5 to 7.5 / 0.0 / 0.5mm/step]

002

NA: 3-Hole

ENG

003

Europe: 4-Hole

ENG

004

NEU: 4-Hole

ENG

005

NA: 2-Hole

ENG

002

NA: 3-Hole

ENG

003

Europe: 4-Hole

ENG

004

NEU: 4-Hole

ENG

005

NA: 2-Hole

ENG

002

NA: 3-Hole

ENG

003

Europe: 4-Hole

ENG

004

NEU: 4-Hole

ENG

005

NA: 2-Hole

ENG

6143

[Jogger Pos Adj:1K FIN]

Adjusts width (main scan direction) of jogger when running specified paper conformity.

 Adjusts value to -: move towards jogger width is tighter than base value.

 Adjusts value to +: move towards jogger width is wider than base value.

001

A3 SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

006

B5 LEF

ENG

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

011

12"x18"

ENG

012

8K SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

013

16K SEF

ENG

014

16K LEF

ENG

015

Other

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

6143

[Jogger Pos Adj:1K FIN]

Adjusts width (main scan direction) of jogger when running specified paper conformity.

 Adjusts value to -: move towards jogger width is tighter than base value.

 Adjusts value to +: move towards jogger width is wider than base value.

001

A3 SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

006

B5 LEF

ENG

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

011

12"x18"

ENG

012

8K SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

013

16K SEF

ENG

014

16K LEF

ENG

015

Other

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

6143

[Jogger Pos Adj:1K FIN]

Adjusts width (main scan direction) of jogger when running specified paper conformity.

 Adjusts value to -: move towards jogger width is tighter than base value.

 Adjusts value to +: move towards jogger width is wider than base value.

001

A3 SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

006

B5 LEF

ENG

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

011

12"x18"

ENG

012

8K SEF

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

013

16K SEF

ENG

014

16K LEF

ENG

015

Other

ENG

[-1.5 to 1.5 / 0.0 / 0.5mm/step]

Adjusts width (main scan direction) of jogger when running conformity to except the specified paper.

 Adjusts value to -: move towards jogger width is tighter than base value.

 Adjusts value to +: move towards jogger width is wider than base value.

6144

[Main-scan Punch Pos Adj:1K FIN]

Adjusts position of width direction (main scan direction) for punch.

 Adjusting value to -: hole position moves toward front side of machine.

 Adjusting value to +: hole position moves toward rear side of machine.

001

JPN/EU: 2-Hole

ENG

[-2.0 to 2.0 / 0.0 / 0.4mm/step]

002

NA: 3-Hole

ENG

003

Europe: 4-Hole

ENG

004

NEU: 4-Hole

ENG

005

NA: 2-Hole

ENG

6145

[Skew Correct Buckle Adj:1K FIN]

Adjusts the skew correction bending amount when punching specified paper.

 Adjusts value to -: buckling amount decreases

 Adjusts value to +:buckling amount increases.

001

A3 SEF

ENG

[-5.0 to 5.0 / 0.0 / 0.2mm/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

006

B5 LEF

ENG

[-5.0 to 5.0 / 0.0 / 0.2mm/step]

007

A5 LEF

ENG

008

DLT SEF

ENG

009

LG SEF

ENG

010

LT SEF

ENG

011

LT LEF

ENG

[-5.0 to 5.0 / 0.0 / 0.2mm/step]

012

HLT LEF

ENG

013

12"x18"

ENG

014

8K SEF

ENG

015

16K SEF

ENG

016

16K LEF

ENG

017

Other

ENG

[-5.0 to 5.0 / 0.0 / 0.2mm/step]

Adjusts the skew correction bending amount when punching except the specified paper.

 Adjusts value to -: buckling amount decreases

 Adjusts value to +: buckling amount increases.

6146

[Skew Correct Ctrl SW:1K FIN]

Switches way to control (Still buckling 0: enable / 1: disable) skew correction when punching specified paper.

001

A3 SEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

002

B4 SEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

003

A4 SEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

004

A4 LEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

005

B5 SEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

006

B5 LEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

007

A5 LEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

008

DLT SEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

009

LG SEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

010

LT SEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

011

LT LEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

012

HLT LEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

013

12"x18"

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

014

8K SEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

015

16K SEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

016

16K LEF

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

017

Other

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

Switches way to control (Still buckling 0: enable / 1: disable) skew correction when punching except the specified paper.

017

Other

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

Switches way to control (Still buckling 0: enable / 1: disable) skew correction when punching except the specified paper.

017

Other

ENG

[0 or 1 / 0 / 1/step]

0: enable

1: disable

Switches way to control (Still buckling 0: enable / 1: disable) skew correction when punching except the specified paper.

6147

[Booklet Folder Pos Adj:1K FIN]

Adjusts saddle stitch folding position (sub scan direction) of specified paper.

 Adjusting value to -: folding position moves toward trailing edge of paper when intaking.

 Adjusting value to +: folding position moves toward leading edge of paper when intaking.

001

A3 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

002

B4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

003

A4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

004

B5 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

005

DLT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

006

LG SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

007

LT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

008

12"x18"

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

6147

[Booklet Folder Pos Adj:1K FIN]

Adjusts saddle stitch folding position (sub scan direction) of specified paper.

 Adjusting value to -: folding position moves toward trailing edge of paper when intaking.

 Adjusting value to +: folding position moves toward leading edge of paper when intaking.

001

A3 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

002

B4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

003

A4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

004

B5 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

005

DLT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

006

LG SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

007

LT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

008

12"x18"

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

6147

[Booklet Folder Pos Adj:1K FIN]

Adjusts saddle stitch folding position (sub scan direction) of specified paper.

 Adjusting value to -: folding position moves toward trailing edge of paper when intaking.

 Adjusting value to +: folding position moves toward leading edge of paper when intaking.

001

A3 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

002

B4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

003

A4 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

004

B5 SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

005

DLT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

006

LG SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

007

LT SEF

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

008

12"x18"

ENG

[-3.0 to 3.0 / 0.0 / 0.2mm/step]

6148

[Fold Times Adj: 1K FIN]

Adjusts extra folding times (time) for folding when saddle stitching.

001

-

ENG

[0 to 29 / 0 / 1sec/step]

6149

[Last Paper Pos Time Adj:1K FIN]

Adjust positioning times to last paper of set.

001

-

*ENG

[0 to 1 / 0 / 1time/step]

6150

[PositioningStrtTimingAdj:1KFIN]

Adjusts the positioning roller operation start timing when positioning specified paper.

 Adjusts value to -: forwards the start timing

 Adjusts value to +: delays the start timing

001

A3 SEF

ENG

[-100 to 100 / 0 / 10msec/step]

002

B4 SEF

ENG

003

A4 SEF

ENG

004

A4 LEF

ENG

005

B5 SEF

ENG

006

B5 LEF

ENG

007

DLT SEF

ENG

008

LG SEF

ENG

009

LT SEF

ENG

010

LT LEF

ENG

011

12"x18"

ENG

012

8K SEF

ENG

013

16K SEF

ENG

014

16K LEF

ENG

015

Other

ENG

Adjusts the positioning roller operation start timing when positioning except the specified paper.

 Adjusts value to -: forwards the start timing

 Adjusts value to +: delays the start timing

6151

[PosTimeAdj(LstPr2ndTime):1KFIN]

Adjusts 2nd time to positioning the last sheet of the set.

 Adjusts the value to -: shortens the positioning time

 Adjusts the value to +: extends the positioning time

The positioning for the last sheet is done when [Last Paper Pos Time Adj:1K FIN] adjust value is set to 1.

001

-

ENG

[-100 to 100 / 0 / 10msec/step]

6152

[PosTiAdj(ExcLstPr3rdTi):1KFIN]

Adjust positioning time for specified paper except the last sheet 2nd time.

 Adjusts the value to -: shortens the positioning time

 Adjusts the value to +: extends the positioning time

001

A3 SEF

ENG

[-100 to 100 / 0 / 10msec/step]

002

B4 SEF

ENG

[-100 to 100 / 0 / 10msec/step]

003

A4 SEF

ENG

[-100 to 100 / 0 / 10msec/step]

004

A4 LEF

ENG

[-100 to 100 / 0 / 10msec/step]

005

B5 SEF

ENG

[-100 to 100 / 0 / 10msec/step]

006

B5 LEF

ENG

[-100 to 100 / 0 / 10msec/step]

007

DLT SEF

ENG

[-100 to 100 / 0 / 10msec/step]

008

LG SEF

ENG

[-100 to 100 / 0 / 10msec/step]

009

LT SEF

ENG

[-100 to 100 / 0 / 10msec/step]

010

LT LEF

ENG

[-100 to 100 / 0 / 10msec/step]

011

12"x18"

ENG

[-100 to 100 / 0 / 10msec/step]

012

8K SEF

ENG

[-100 to 100 / 0 / 10msec/step]

013

16K SEF

ENG

[-100 to 100 / 0 / 10msec/step]

014

16K LEF

ENG

[-100 to 100 / 0 / 10msec/step]

015

Other

ENG

[-100 to 100 / 0 / 10msec/step]

Adjust positioning time for other than the specified paper except the last sheet 2nd time.

 Adjusts the value to -: shortens the positioning time

 Adjusts the value to +: extends the positioning time

6154

[Pos Time Adj By Sheet: 1K FIN]

Adjusts the positioning time when stocked specified amount.

 Adjusts the value to -: shortens the positioning time

 Adjusts the value to +: extends the positioning time

001

1 - 10 Sheets

ENG

[-100 to 100 / 0 / 10msec/step]

002

11 - 20 Sheets

ENG

003

21 - 30 Sheets

ENG

004

31 - 40 Sheets

ENG

005

41 - 50 Sheets

ENG

6160

[Finisher Free Run: 1K FIN]

001

Free Run 1

ENG

[0 or 1 / 0 / 1/step]

Executes shift mode no paper free run.

002

Free Run 2

ENG

[0 or 1 / 0 / 1/step]

Executes edge stitch (near side 1 point stitch) mode no paper free run.

003

Free Run 3

ENG

[0 or 1 / 0 / 1/step]

Executes saddle stitch mode no paper free run.

(Does not execute with model with no saddle stitch unit)

004

Free Run 4

ENG

[0 or 1 / 0 / 1/step]

Executes saddle stitch mode no paper free run.

(Does not execute with model with no saddle stitch unit)

6161

[FIN (1K FIN) INPUT Check]

See page 3-1

6170

[Bridge: INPUT Check]

See page 3-1

6170

[Bridge: INPUT Check]

See page 3-1

6170

[Bridge: INPUT Check]

See page 3-1

6171

[Bridge: OUTPUT Check]

See page 3-31

6171

[Bridge: OUTPUT Check]

See page 3-31

6171

[Bridge: OUTPUT Check]

See page 3-31

6162

[FIN (1K FIN) OUTPUT Check]

See page 3-31

6172

[Shift Tray: INPUT Check]

See page 3-1

6173

[Shift Tray: OUTPUT Check]

See page 3-31

6174

[1 Bin: INPUT Check]

See page 3-1

6800

[Sheet Conversion (Thick Paper)]

Permits punching, including tab sheets.

001

-

CTL

[1 to 3 / 3 / 1/step]

1: 1 pages

2: 2 pages

3: 3 pages

6801

[1-pass Stamp Unit]

001

-

*ENG

[0 or 1 / 0 / 1/step]

0: NO

1: YES

For 1 path simultaneous duplex models only. Sets installed/not installed of DONE stamp unit.

6810

[Ring Bind Sheet Conversion (Thick Paper)]

-

001

-

CTL

[1 to 3 / 3 / 1/step]

1: 1 pages

2: 2 pages

3: 3 pages

6830

[Extra Staples]

More than the standard number of sheets can be stapled. This SP sets the additional number of sheets (This Setting + Standard Number = maximum number of sheets).

 If the number of the maximum for staples is increased, and the mechanical warranty of the unit can be guaranteed, then the setting can take effect without changing the controller software.

 However, assurance that mechanical performance can be guaranteed is required before changing the setting to increase the staple load for more than the maximum in the feed/exit specifications. Raising this setting without quality assurance could damage the machine.

001

Staple positions other than booklet stapling

*CTL

[0 to 50 / 0 / 1/step]

002

2 Booklet stapling

*CTL

[0 to 50 / 0 / 1/step]

Makes possible for staple to saddle stitch more sheets than basic amount. Saddle stitch staple max. amount will be recognized as the total of this SP’s value and the basic amount.

003

Finisher booklet max. paper count custom setting

*CTL

[0 to 50 / 0 / 1/step]

Makes possivle for finisher to middle fold more than the basic foldable amount. Middle fold max. amount will be recognized as the total of this SP’s value and basic Middle fold amunt.

003

Finisher booklet max. paper count custom setting

*CTL

[0 to 50 / 0 / 1/step]

Makes possivle for finisher to middle fold more than the basic foldable amount. Middle fold max. amount will be recognized as the total of this SP’s value and basic Middle fold amunt.

003

Finisher booklet max. paper count custom setting

*CTL

[0 to 50 / 0 / 1/step]

Makes possivle for finisher to middle fold more than the basic foldable amount. Middle fold max. amount will be recognized as the total of this SP’s value and basic Middle fold amunt.

6890

[Punch Function Enabled (Z Fold)]

001

-

CTL

[1 to 0 / 0 / 1/step]

0: No Punch

1: Punching OK

6890

[Punch Function Enabled (Z Fold)]

001

-

CTL

[1 to 0 / 0 / 1/step]

0: No Punch

1: Punching OK

6890

[Punch Function Enabled (Z Fold)]

001

-

CTL

[1 to 0 / 0 / 1/step]

0: No Punch

1: Punching OK

6900

[ADF Bottom Plate Setting]

001

-

*ENG

[0 or 1 / 0 / 1/step]

0: Bottom plate rise on original set (default)

1: Bottom plate rise on paper exit signal.

For 1 path simultaneous duplex models only. Changes bottom plate rising mode.