MAIN SP TABLES-3 Savin MP C3003, Ricoh MP C3003 Service Manual

HOME PAGE | < Previous | Contents | Next >

Main SP Tables-3 ‌

2.5 MAIN SP TABLES-3

SP Mode Tables

2.5.1 SP3-XXX (PROCESS)

3011

[Manual ProCon :Exe]

001

Normal ProCon

ENG

[0 or 1 / 0 / 1/step] [Execute]

Executes Pro-Con.

002

Density Adjustment

ENG

[0 or 1 / 0 / 1/step] [Execute]

Executes toner density adjusting Pro-Con.

003

ACC RunTime ProCon

ENG

[0 or 1 / 0 / 1/step] [Execute]

Executes pre-ACC Pro-Con.

004

Full MUSIC

ENG

[0 or 1 / 0 / 1/step] [Execute]

Executes Pro-Con / full MUSIC.

005

Normal MUSIC

ENG

[0 or 1 / 0 / 1/step] [Execute]

Executes Pro-Con / normal MUSIC.

3012	[ProCon OK?]
	2 digits per color from left, in the order of YMCK *Refer to below for execution result content.
001	History:Last(Front)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays latest Pro-Con execution result.
002	History:Last 2(Front)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for the time before last.

Main SP Tables-3

003	History:Last 3(Front)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 3 times before.
004	History:Last 4(Front)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 4 times before.
005	History:Last 5(Front)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 5 times before.
006	History:Last 6(Front)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 6 times before.
007	History:Last 7(Front)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 7 times before.
008	History:Last 8(Front)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 8 times before.
009	History:Last 9(Front)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 9 times before.
010	History:Last 10(Front)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 10 times before.
011	History:Last(Center)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays latest Pro-Con execution result.
012	History:Last 2(Center)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 2 times before.
013	History:Last 3(Center)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 3 times before.
014	History:Last 4(Center)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 4 times before.
015	History:Last 5(Center)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 5 times before.

SP Mode Tables

Main SP Tables-3

016	History:Last 6(Center)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 6 times before.
017	History:Last 7(Center)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 7 times before.
018	History:Last 8(Center)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 8 times before.
019	History:Last 9(Center)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 9 times before.
020	History:Last 10(Center)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 10 times before.
021	History:Last(Rear)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays latest Pro-Con execution result.
022	History:Last 2(Rear)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for the time before last.
023	History:Last 3(Rear)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 3 times before.
024	History:Last 4(Rear)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 4 times before.
025	History:Last 5(Rear)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 5 times before.
026	History:Last 6(Rear)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 6 times before.
027	History:Last 7(Rear)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 7 times before.
028	History:Last 8(Rear)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 8 times before.

Main SP Tables-3

029	History:Last 9(Rear)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 9 times before.
030	History:Last 10(Rear)	*ENG	[0 to 99999999 / 0 / 1/step]
	Displays Pro-Con execution result for 10 times before.

*SP3-012 Display result detail

Category	Code	Result name	Description
00 and lager	00	Not executed	Factory default setting(SP default)
10 and lager Result(Normal)	11	Succeed	-
20 and lager ID Sensor	21	ID Sensor Vsg adjust error	Out of range from Vsg=4.0±x.x[V/step]
	22	ID Sensor LED Adjust error	Ifsg>Max
	23	ID Sensor Output error(Positive reflect)	Vsg_reg<Min(Max)
	24	ID Sensor output error(Diffusion reflect)	Vsg_dif<Min(Max)
	25	ID Sensor offset Voltage error(Positive reflect)	Voffset_reg>Max
	26	ID Sensor offset Voltage error(Diffusion reflect)	Voffset_dif>Max
45 and lager ID Pattern detect	45	ID Pattern extract error	Can not detect ID Pattern
	50	Vmin_Bk/K2 error(Max)	K:Vmin_Bk / CMY:K2>Max
	51	Vmin_Bk/K2 error(Min)	K:Vmin_Bk / CMY:K2<Min
	52	K5 error(Max)	K5>Max
	53	K5 error(Min)	K5<Min
	54	K5 calculated approximate point error	K5 calculated approximate point <Min

SP Mode Tables

Main SP Tables-3

	55	Develop gamma error(Max)	Develop gamma >Max
	56	Develop gamma error(Min)	Develop gamma <Min
	57	Start developing voltage:Vk error(Max)	Start developing voltage:Vk>Max
	58	Start developing voltage:Vk error(Min)	Start developing voltage:Vk<Min
	59	Not enough valid data	Adhesion amount data for develop gamma calculation point is under 2
60 and lager Potential adjust	61	LD won’t light	P patter is not written.
	62	Residual potential:Vr error	Vr>Max
	63	Electrified potential:Vd adjust error	Vd can not be adjusted in target range.
	64	Exposure potential:Vpl adjust error	Vpl can not be adjusted in target range
90 and lager Result(End)	90	Potential not adjust	Potential control method is set as [0:FIX]
90 and lager Result(End)	99	Kill	Kill by door open, power off, error. (Set when execute.)

 Execute result sample (In order of YMCK from left)

 Factory default(SP default):[00,00,00,00]

 Starting adjust:[99,99,99,99]

 Fail Vsg adjust(Y):[21,99,99,99]

 Error of Develop gamma Max(C):[99,99,55,99]

 Succeed:[11,11,11,11]

Main SP Tables-3

3014	[IBACC OK?]
3014	Displays latest IBACC execution result.
001	History:Last	*ENG	[0 to 9999 / 0 / 1/step]
002	History:Last 2	*ENG
003	History:Last 3	*ENG
004	History:Last 4	*ENG
005	History:Last 5	*ENG
006	History:Last 6	*ENG
007	History:Last 7	*ENG
008	History:Last 8	*ENG
009	History:Last 9	*ENG
010	History:Last 10	*ENG

3030

[Init TD Sensor :Exe]

001

Execute: ALL

ENG

[0 or 1 / 0 / 1/step] [Execute]

Executes TD sensor initial setting for all colors.

002

Execute: Col

ENG

[0 or 1 / 0 / 1/step] [Execute]

Executes TD sensor initial setting only for chromatic 3 colors.

003

Execute: K

ENG

[0 or 1 / 0 / 1/step] [Execute]

Executes TD sensor initial setting for only (K).

004

Execute: C

ENG

[0 or 1 / 0 / 1/step] [Execute]

Executes TD sensor initial setting for only (C).

SP Mode Tables

Main SP Tables-3

005	Execute: M	ENG	[0 or 1 / 0 / 1/step] [Execute]
	Executes TD sensor initial setting for only (M).
006	Execute: Y	ENG	[0 or 1 / 0 / 1/step] [Execute]
	Executes TD sensor initial setting for only (Y).
020	Agitatiton Time	*ENG	[0 to 200 / 30 / 1sec/step]
	Sets developing powder stirring time for when TD sensor's setting is in initial.
021	Initial TC	*ENG	[1.0 to 15.0 / 7.0 / 0.1wt%/step]
	Sets toner density for initial chemical.
031	Vt Target:K	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Sets Vt target value (K) for when TD sensor's setting is in initial.
032	Vt Target:C	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Sets Vt target value (C) for when TD sensor's setting is in initial.
033	Vt Target:M	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Sets Vt target value (M) for when TD sensor's setting is in initial.
034	Vt Target:Y	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Sets Vt target value (M) for when TD sensor's setting is in initial.
041	Vt Target Corr:K	*ENG	[0.00 to 2.55 / 0.00 / 0.01V/step]
	Sets metachronic correcting amount (K) for when TD sensor's setting is in initial.
042	Vt Target Corr:C	*ENG	[0.00 to 2.55 / 0.00 / 0.01V/step]
	Sets metachronic correcting amount (C) for when TD sensor's setting is in initial.
043	Vt Target Corr:M	*ENG	[0.00 to 2.55 / 0.00 / 0.01V/step]
	Sets metachronic correcting amount (M) for when TD sensor's setting is in initial.

Main SP Tables-3

044

Vt Target Corr:Y

*ENG

[0.00 to 2.55 / 0.00 / 0.01V/step]

Sets metachronic correcting amount (Y) for when TD sensor's setting is in initial.

3031

[TD Sens Init OK?]

001

From Left:YMCK

ENG

[0 to 9999 / 0 / 1/step]

Displays execution result of TD sensor initial setting.

3050	[Force Tnr Supply :Exe]
001	Execute: ALL	ENG	[0 or 1 / 0 / 1/step] [Execute]
	Forcedly supply toner (all colors)
002	Execute: Col	ENG	[0 or 1 / 0 / 1/step] [Execute]
	Forcedly supply toner (only CMY)
003	Execute: K	ENG	[0 or 1 / 0 / 1/step] [Execute]
	Forcedly supply toner (only K)
004	Execute: C	ENG	[0 or 1 / 0 / 1/step] [Execute]
	Forcedly supply toner (only C)
005	Execute: M	ENG	[0 or 1 / 0 / 1/step] [Execute]
	Forcedly supply toner (only M)
006	Execute: Y	ENG	[0 or 1 / 0 / 1/step] [Execute]
	Forcedly supply toner (only Y)
3050	[Force Tnr Supply :Exe]
021	Supply Quantity:K	*ENG	[0.0 to 5.0 / 0.5 / 0.1wt%/step]

SP Mode Tables

Main SP Tables-3

	Sets the amount [wt%/step] to supply toner (K) with Force toner supply.
022	Supply Quantity:C	*ENG	[0.0 to 5.0 / 0.5 / 0.1wt%/step]
	Sets the amount [wt%/step] to supply toner (C) with Force toner supply.
023	Supply Quantity:M	*ENG	[0.0 to 5.0 / 0.5 / 0.1wt%/step]
	Sets the amount [wt%/step] to supply toner (M) with Force toner supply.
024	Supply Quantity:Y	*ENG	[0.0 to 5.0 / 0.5 / 0.1wt%/step]
	Sets the amount [wt%/step] to supply toner (Y) with Force toner supply.
031	ON Time	*ENG	[10 to 1000 / 200 / 1msec/step]
	Sets supply ON time for 1time of force toner supplying process routine.
032	OFF Time	*ENG	[0 to 1000 / 100 / 1msec/step]
	Sets supply OFF time for 1time of force toner supplying process routine.
033	RepeatCount	*ENG	[0 to 255 / 8 / 1times/step]
	Sets repeating times for 1time of force toner supplying process routine.

3072

[T Sensor: Check]

Executes testing mode to test TD sensor's output (Vt) without stating up the engine.

001

Execute Check

ENG

[0 or 1 / 0 / 1/step] [Execute]

3073	[T Sensor Measurement Value:]
3073	Displays output test value of TD sensor.
001	Vt:K	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
002	Vt:C	*ENG
003	Vt:M	*ENG
004	Vt:Y	*ENG

Main SP Tables-3

3100	[Tonner End Detection: Set]
001	ON/OFF	*ENG	[0 or 1 / 0 / 1/step]
	Whether to decide NE/TE. 0: Enable 1: Disable
002	NE Detection	*ENG	[0 or 1 / 0 / 1/step]
	NE decision method. 0: Counter & Toner End Sensor 1: Toner End Sensor Only

3101	[Toner Status :Disp]
	Displays remaining toner.
001	K	ENG
			[0 to 10 / 10 / 1/step]
002	C	ENG
			10: Full
003	M	ENG	1: Near end
			0: Toner end
004	Y	ENG

3102	[Toner Remain:Disp]
3102	Remaining toner calculated form motor running time.
001	Bottle Motor: Bk	*ENG	[0.000 to 700.000 / 560.000 / 0.001g]
002	Bottle Motor: C	*ENG	[0.000 to 700.000 / 440.000 / 0.001g]
003	Bottle Motor: M	*ENG
004	Bottle Motor: Y	*ENG
3102	[Toner Remain:Disp]
3102	Remaining toner calculated from imaging size.
011	Pixel: Bk	*ENG	[0.000 to 700.000 / 560.000 / 0.001g]

SP Mode Tables

Main SP Tables-3

012	Pixel: C	*ENG	[0.000 to 700.000 / 440.000 / 0.001g]
013	Pixel: M	*ENG
014	Pixel: Y	*ENG
3102	[Toner Remaining: Display]
3102	Filler content of new bottle.
021	Fill Amount: Bk	*ENG	[0 to 600 / 560 / 1g/step]
022	Fill Amount: C	*ENG	[0 to 600 / 440 / 1g/step]
023	Fill Amount: M	*ENG
024	Fill Amount: Y	*ENG
3102	[Toner Remain:Disp]
3102	Consumption amount of toner.
031	Pixel: Toner Consumption x 2: C	*ENG	[0.000 to 1000.000 / 0.000 / 0.001g]
032	Pixel: Toner Consumption x 2: Bk	*ENG
033	Pixel: Toner Consumption x 2: M	*ENG
034	Pixel: Toner Consumption x 2: Y	*ENG
041	Drive Motor: Toner Consumption x 1: Bk	*ENG
042	Drive Motor: Toner Consumption x 1: C	*ENG
043	Drive Motor: Toner Consumption x 1: M	*ENG
044	Drive Motor: Toner Consumption x 1: Y	*ENG

3103	[Bottle Off Time]

Main SP Tables-3

	-
001	Bk	*ENG	[0 to 4294967295 / 0 / 1/step]
002	C	*ENG
003	M	*ENG
004	Y	*ENG

3104	[Flag: Display]
3104	Sets flag when replacing toner bottle.
001	NE Toner: Bk	*ENG	[0 or 1 / 0 / 1/step]
002	NE Toner: C	*ENG
003	NE Toner: M	*ENG
004	NE Toner: Y	*ENG
3104	[Flag: Display]
3104	Sets Flag when Vt ends.
011	Vt end:Bk	*ENG	[0 or 1 / 0 / 1/step]
012	Vt end:C	*ENG
013	Vt end:M	*ENG
014	Vt end:Y	*ENG

3110	[Near End Thresh]
3110	-
001	Bk	*ENG	[0 to 500 / 65 / 1g/step]
002	C	*ENG	[0 to 500 / 45 / 1g/step]
003	M	*ENG
004	Y	*ENG

SP Mode Tables

Main SP Tables-3

3111

[Pixel NE: M/A]

001

*ENG

[0 to 1000 / 411 / 0.001mg/cm2/step]

002

*ENG

[0 to 1000 / 444 / 0.001mg/cm2/step]

003

*ENG

[0 to 1000 / 500 / 0.001mg/cm2/step]

004

*ENG

[0 to 1000 / 444 / 0.001mg/cm2/step]

3120	[TE Sn Detect Thresh]
3120	-
001	Bk	*ENG	[0 to 100 / 50 / 1%/step]
002	C	*ENG
003	M	*ENG
004	Y	*ENG

3121	[TE Counter: Disp]
3121	No toner decision times from end sensor.
001	Bk	*ENG	[0 to 99 / 0 / 1times/step]
002	C	*ENG
003	M	*ENG
004	Y	*ENG

3122

[TE Sn NE Thresh]

001

*ENG

[0 to 99 / 80 / 1times/step]

Main SP Tables-3

002	C	*ENG
003	M	*ENG
004	Y	*ENG

3131	[Vt TE Thresh]
001	Delta Vt Thresh	*ENG	[0.00 to 5.00 / 0.50 / 0.01V/step]
	Threshold to start adding delta Vt after NE.
002	Delta Vt Sum Thresh	*ENG	[0 to 99 / 10 / 1V/step]
	Threshold to decide TE after NE.
011	Delta Vt Thresh BF NE	*ENG	[0.00 to 5.00 / 0.50 / 0.01V/step]
	Threshold to start adding delta Vt before NE.
012	Delta Vt Sum Thresh BF NE	*ENG	[0 to 99 / 10 / 1V/step]
	Threshold to decide TE before NE.

3132	[Delta Vt Sum]
3132	Added value of delta Vt.
001	Bk	*ENG	[0.00 to 99.00 / 0.00 / 0.01V/step]
002	C	*ENG
003	M	*ENG
004	Y	*ENG

3133	[TE Detect :Set]
001	Set Sheets(Min)	*ENG	[0 to 50 / 10 / 1sheet/step]
	Sets min. assured sheets to display toner end after toner near end is fixed.
002	Set Sheets(Max)	*ENG	[0 to 5000 / 1000 / 1sheet/step]
	Sets max. assured sheets to display toner end after toner near end is fixed.

SP Mode Tables

Main SP Tables-3

3133	[TE Detect :Set]
3133	Displays the amount of sheets printed after toner near end is fixed.
011	Page Cnt:K	*ENG	[0 to 5000 / 0 / 1sheet/step]
012	Page Cnt:C	*ENG
013	Page Cnt:M	*ENG
014	Page Cnt:Y	*ENG
3133	[TE Detect :Set]
3133	Sets dimension (cm2) in terms of blotted out A4 sized sheet to decide as toner end after near toner end is fixed.
021	Set Pxl Cnt	*ENG	[0 to 1000000 / 7000 / 1cm2/step]
3133	[TE Detect :Set]
3133	Displays the amount used with dimension (cm2) in terms of blotted out.
031	Pxl Cnt:K	*ENG	[0 to 1000000 / 0 / 1cm2/step]
032	Pxl Cnt:C	*ENG
033	Pxl Cnt:M	*ENG
034	Pxl Cnt:Y	*ENG

3150	[TE Sensor :Set]
001	SamplingCount	*ENG	[4 to 20 / 10 / 1counts/step]
	Sets arrangement size of TE sensor.
002	Judge:p	*ENG	[0.2 to 1.0 / 0.8 / 0.1/step]
	Sets threshold for to decide toner existing..
3150	[T TE Sensor :Set]
	Percentage for "No remaining toner" of storing arrangement.
003	result:K	*ENG	[0.0 to 0.1 / 0.5 / 0.1/step]
004	result:C	*ENG

Main SP Tables-3

005	result:M	*ENG
006	result:Y	*ENG

3160

[Bottle Drive :Set]

Select bottle driving method.

001

Bottle Drive System

*ENG

[0 or 1 / 0 / 1/step]

0: TE Sensor Control

1: TonerSupplyMotor Track Control

3161	[Bottle Drive :Set]
3161	-
001	Drive ON Time:K	[0 to 2000 / 900 / 100msec/step]
002	Drive ON Time:C
003	Drive ON Time:M
004	Drive ON Time:Y

3162	[Bottle Drive :Set]
3162	-
001	Drive OFF Time:K	[0 to 5000 / 100 / 100msec/step]
002	Drive OFF Time:C
003	Drive OFF Time:M
004	Drive OFF Time:Y

3165	[Hopper Drive :Set]
	-
001	Speed Adjustment:K	[-58 to 50 / 18 / 1%/step]
002	Speed Adjustment:C

SP Mode Tables

Main SP Tables-3

003	Speed Adjustment:M		[-58 to 50 / 40 / 1%/step]
004	Speed Adjustment:Y		[-58 to 50 / 18 / 1%/step]

3200	[TnrDensity]
3200	Displays toner density (wt%).
001	K	*ENG	[0 to 25.5 / 0 / 0.1 wt%/step]
002	C	*ENG
003	M	*ENG
004	Y	*ENG

3201	[TnrDensity]
3201	Sets min./max. density (wt%) for toner density controlling range.
001	Upper TC	*ENG	[1.0 to 15.0 / 9.0 / 0.1wt%/step]
002	Lower TC	*ENG	[1.0 to 15.0 / 2.0 / 0.1wt%/step]

3205	[TD.Sens Sensitivity]
	Displays TD sensor sensitivity HL calculated from test value of HST density control (SP3-711 to 714-***)
001	HL:K	*ENG	[0.200 to 1.000 / 0.350 / 0.001-V/wt%/step]
002	HL:C	*ENG
003	HL:M	*ENG
004	HL:Y	*ENG
3205	[TD.Sens Sensitivity]
	Displays TD sensor sensitivity HM calculated from test value of HST density control (SP3-711 to 714-***)
011	HM:K	*ENG	[0.200 to 1.000 / 0.350 / 0.001-V/wt%/step]
012	HM:C	*ENG

Main SP Tables-3

013	HM:M	*ENG
014	HM:Y	*ENG
3205	[TD.Sens Sensitivity]
	Displays TD sensor sensitivity ML calculated from test value of HST density control (SP3-711 to 714-***)
021	ML:K	*ENG	[0.200 to 1.000 / 0.350 / 0.001-V/wt%/step]
022	ML:C	*ENG
023	ML:M	*ENG
024	ML:Y	*ENG
3205	[TD.Sens Sensitivity]
031	Upper Limit	*ENG	[0.200 to 0.500 / 0.440 / 0.001-V/wt%/step]
	Sets max. sensitivity for to calculate TD sensor sensitivity.
032	Lower Limit	*ENG	[0.150 to 0.500 / 0.180 / 0.001-V/wt%/step]
	Sets min. sensitivity for to calculate TD sensor sensitivity.
033	TC Between H-M:K	*ENG	[1.00 to 10.00 / 4.50 / 0.01wt%
	Sets HM interval as TC of K for to calculate TD sensor sensitivity.
034	TC Between M-L:K	*ENG	[1.00 to 10.00 / 4.40 / 0.01wt%
	Sets ML interval as TC of K for to calculate TD sensor sensitivity.
043	TC Between H-M:Col	*ENG	[1.00 to 10.00 / 4.20 / 0.01wt%
	Sets HM interval as TC of CMY for to calculate TD sensor sensitivity.
044	TC Between H-M:Col	*ENG	[1.00 to 10.00 / 4.40 / 0.01wt%
	Sets ML interval as TC of CMY for to calculate TD sensor sensitivity.

3210

[TD.Sens:Vt :Disp]

Displays latest T sensor output.

SP Mode Tables

001	Current: K	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
002	Current: C	*ENG
003	Current: M	*ENG
004	Current: Y	*ENG

001	Current: K	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
002	Current: C	*ENG
003	Current: M	*ENG
004	Current: Y	*ENG

001	Current: K	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
002	Current: C	*ENG
003	Current: M	*ENG
004	Current: Y	*ENG

3211	[Vt Limits Err :Disp]
002	Upper Threshold	*ENG	[0.00 to 5.00 / 4.70 / 0.01V/step]
	Sets Vt upper limit threshold to decide as Vt upper limit error.
003	Thresh Num of UpperCounter	*ENG	[0 to 255 / 20 / 1times/step]
	Sets the number of times excessing Vt upper limit to set off SC360 to 363 (Vt upper limit error).
004	Lower Threshold	*ENG	[0.00 to 5.00 / 0.50 / 0.01V/step]
	Sets Vt upper limit threshold to decide as Vt lower limit error.
005	Threshold Num of LowerCounter	*ENG	[0 to 255 / 10 / 1times/step]
	Sets the number of times excessing Vt lower limit to set off SC365 to 363 (Vt upper limit error).
3211	[Vt Limits Err :Disp]
	Counts times of Vt(K/C/M/Y) excessing Vt upper limit threshol
011	Upper Counter: Bk	*ENG	[0 to 255 / 0 / 1times/step]
012	Upper Counter: C	*ENG
013	Upper Counter: M	*ENG
014	Upper Counter: Y	*ENG
3211	[Vt Limits Err :Disp]
	Counts times of Vt(K/C/M/Y) excessing Vt lower limit threshold.
021	Lower Counter: Bk	*ENG	[0 to 255 / 0 / 1times/step]
022	Lower Counter: C	*ENG

3211	[Vt Limits Err :Disp]
002	Upper Threshold	*ENG	[0.00 to 5.00 / 4.70 / 0.01V/step]
	Sets Vt upper limit threshold to decide as Vt upper limit error.
003	Thresh Num of UpperCounter	*ENG	[0 to 255 / 20 / 1times/step]
	Sets the number of times excessing Vt upper limit to set off SC360 to 363 (Vt upper limit error).
004	Lower Threshold	*ENG	[0.00 to 5.00 / 0.50 / 0.01V/step]
	Sets Vt upper limit threshold to decide as Vt lower limit error.
005	Threshold Num of LowerCounter	*ENG	[0 to 255 / 10 / 1times/step]
	Sets the number of times excessing Vt lower limit to set off SC365 to 363 (Vt upper limit error).
3211	[Vt Limits Err :Disp]
	Counts times of Vt(K/C/M/Y) excessing Vt upper limit threshol
011	Upper Counter: Bk	*ENG	[0 to 255 / 0 / 1times/step]
012	Upper Counter: C	*ENG
013	Upper Counter: M	*ENG
014	Upper Counter: Y	*ENG
3211	[Vt Limits Err :Disp]
	Counts times of Vt(K/C/M/Y) excessing Vt lower limit threshold.
021	Lower Counter: Bk	*ENG	[0 to 255 / 0 / 1times/step]
022	Lower Counter: C	*ENG

3211	[Vt Limits Err :Disp]
002	Upper Threshold	*ENG	[0.00 to 5.00 / 4.70 / 0.01V/step]
	Sets Vt upper limit threshold to decide as Vt upper limit error.
003	Thresh Num of UpperCounter	*ENG	[0 to 255 / 20 / 1times/step]
	Sets the number of times excessing Vt upper limit to set off SC360 to 363 (Vt upper limit error).
004	Lower Threshold	*ENG	[0.00 to 5.00 / 0.50 / 0.01V/step]
	Sets Vt upper limit threshold to decide as Vt lower limit error.
005	Threshold Num of LowerCounter	*ENG	[0 to 255 / 10 / 1times/step]
	Sets the number of times excessing Vt lower limit to set off SC365 to 363 (Vt upper limit error).
3211	[Vt Limits Err :Disp]
	Counts times of Vt(K/C/M/Y) excessing Vt upper limit threshol
011	Upper Counter: Bk	*ENG	[0 to 255 / 0 / 1times/step]
012	Upper Counter: C	*ENG
013	Upper Counter: M	*ENG
014	Upper Counter: Y	*ENG
3211	[Vt Limits Err :Disp]
	Counts times of Vt(K/C/M/Y) excessing Vt lower limit threshold.
021	Lower Counter: Bk	*ENG	[0 to 255 / 0 / 1times/step]
022	Lower Counter: C	*ENG

Main SP Tables-3

023	Lower Counter: M	*ENG
024	Lower Counter: Y	*ENG

3212	[Vt Shift :Set]
3212	Sets middle speed correction amount for correcting Vt shift caused by line speed.
001	Mid Spd:K	*ENG	[0.00 to 2.55 / D146, D147: 8 D148: 0 D149, D150: 3 / 0.01V/step]
002	Mid Spd:C	*ENG	[0.00 to 2.55 / 0.07 / 0.01V/step]
003	Mid Spd:M	*ENG
004	Mid Spd:Y	*ENG
3212	[Vt Shift :Set]
3212	Sets low speed correction amount for correcting Vt shift caused by line speed.
011	Low Spd:K	*ENG	[0.00 to 2.55 / 0.14 / 0.01V/step]
012	Low Spd:C	*ENG
013	Low Spd:M	*ENG
014	Low Spd:Y	*ENG
3212	[Vt Shift :Set]
3212	Sets ON/OFF TC correction amount of Vt shift.
101	ON/OFF	*ENG	[0 or 1 / 1 / 1/step] 0: OFF 1:ON
3212	[Vt Shift :Set]
3212	Displays TC correction amount of Vt shift.
111	TC Mid Spd:K	*ENG	[-0.50 to 0.50 / 0.00 / 0.01V/step]
112	TC Mid Spd:C	*ENG
113	TC Mid Spd:M	*ENG

SP Mode Tables

114	TC Mid Spd:Y	*ENG
121	TC Low Spd:K	*ENG
122	TC Low Spd:C	*ENG
123	TC Low Spd:M	*ENG
124	TC Low Spd:Y	*ENG

114	TC Mid Spd:Y	*ENG
121	TC Low Spd:K	*ENG
122	TC Low Spd:C	*ENG
123	TC Low Spd:M	*ENG
124	TC Low Spd:Y	*ENG

114	TC Mid Spd:Y	*ENG
121	TC Low Spd:K	*ENG
122	TC Low Spd:C	*ENG
123	TC Low Spd:M	*ENG
124	TC Low Spd:Y	*ENG

3214

[Vt Save :Set]

Saves Vt based to image area ratio.

001

Coverage Thresh

*ENG

[0 to 100 / 20 / 1%/step]

3214

[Vt Save :Set]

Saves Vt based to image area ratio.

001

Coverage Thresh

*ENG

[0 to 100 / 20 / 1%/step]

3214

[Vt Save :Set]

Saves Vt based to image area ratio.

001

Coverage Thresh

*ENG

[0 to 100 / 20 / 1%/step]

Main SP Tables-3

3218	[Vt Err Flag :Disp]
001	UppErr Flag: K	*ENG	[0 or 1 / 0 / 1/step]
	Sets flag "1" when Vt(K) excesses Vt upper limit error threshold (SP3-221-002) even 1 time.
002	UppErr Flag: C	*ENG	[0 or 1 / 0 / 1/step]
	Sets flag "1" when Vt(C) excesses Vt upper limit error threshold (SP3-221-002) even 1 time.
003	UppErr Flag: M	*ENG	[0 or 1 / 0 / 1/step]
	Sets flag "1" when Vt(M) excesses Vt upper limit error threshold (SP3-221-002) even 1 time.
004	UppErr Flag: Y	*ENG	[0 or 1 / 0 / 1/step]
	Sets flag "1" when Vt(Y) excesses Vt upper limit error threshold (SP3-221-002) even 1 time.
011	LowErr Flag: K	*ENG	[0 or 1 / 0 / 1/step]
	Sets flag "1" when Vt(K) excesses Vt lower limit error threshold (SP3-221-004) even 1 time.
012	LowErr Flag: C	*ENG	[0 or 1 / 0 / 1/step]

Main SP Tables-3

	Sets flag "1" when Vt(C) excesses Vt lower limit error threshold (SP3-221-004) even 1 time.
013	LowErr Flag: M	*ENG	[0 or 1 / 0 / 1/step]
	Sets flag "1" when Vt(M) excesses Vt lower limit error threshold (SP3-221-004) even 1 time.
014	LowErr Flag: Y	*ENG	[0 or 1 / 0 / 1/step]
	Sets flag "1" when Vt(Y) excesses Vt lower limit error threshold (SP3-221-004) even 1 time.

3219	[TD.Sens:Vt':Disp]
3219	Displays Vt before Vt shift correction.
001	Vt'0Current: K	ENG	[0.00 to 5.00 / 0.00 / 0.01V/step]
002	Vt'0Current: C	ENG
003	Vt'0Current: M	ENG
004	Vt'0Current: Y	ENG
011	Vt'1Current: K	ENG
012	Vt'1Current: C	ENG
013	Vt'1Current: M	ENG
014	Vt'1Current: Y	ENG
021	Vt'2Current: K	ENG
022	Vt'2Current: C	ENG
023	Vt'2Current: M	ENG
024	Vt'2Current: Y	ENG

3220

[Vtcnt :Disp/Set]

001

Current: K

*ENG

[2.00 to 5.00 / 3.60 / 0.01V/step]

Displays/Sets Current TD Sensor Control Voltage (K).

SP Mode Tables

Main SP Tables-3

002	Current: C	*ENG	[2.00 to 5.00 / 3.75 / 0.01V/step]
	Displays/Sets Current TD Sensor Control Voltage (C).
003	Current: M	*ENG	[2.00 to 5.00 / 3.75 / 0.01V/step]
	Displays/Sets Current TD Sensor Control Voltage (M).
004	Current: Y	*ENG	[2.00 to 5.00 / 3.75 / 0.01V/step]
	Displays/Sets Current TD Sensor Control Voltage (Y).
011	Initial: K	*ENG	[2.00 to 5.00 / 3.60 / 0.01V/step]
	Displays control voltage of TD sensor when default setting TD sensor.
012	Initial: C	*ENG	[2.00 to 5.00 / 3.75 / 0.01V/step]
	Displays control voltage of TD sensor when default setting TD sensor.
013	Initial: M	*ENG	[2.00 to 5.00 / 3.75 / 0.01V/step]
	Displays control voltage of TD sensor when default setting TD sensor.
014	Initial: Y	*ENG	[2.00 to 5.00 / 3.75 / 0.01V/step]
	Displays control voltage of TD sensor when default setting TD sensor.

3230	[Vtref :Disp/Set]
001	Current: K	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Displays / Sets current target value of TD sensor's output voltage: Vtref (K).
002	Current: C	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Displays / Sets current target value of TD sensor's output voltage: Vtref (C).
003	Current: M	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Displays / Sets current target value of TD sensor's output voltage: Vtref (M).
004	Current: Y	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Displays / Sets current target value of TD sensor's output voltage: Vtref (Y).
011	Initial: K	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]

Main SP Tables-3

	Displays target value of TD sensor's (K) output voltage when executing TD sensor initial setting.
012	Initial: C	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Displays target value of TD sensor's (C) output voltage when executing TD sensor initial setting.
013	Initial: M	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Displays target value of TD sensor's (M) output voltage when executing TD sensor initial setting.
014	Initial: Y	*ENG	[0.00 to 5.00 / 2.50 / 0.01V/step]
	Displays target value of TD sensor's (Y) output voltage when executing TD sensor initial setting.
3230	[Vtref :Disp/Set]
	Displays pixel correction amount of Vtref correction by image area.
021	Pixel Correction: K	*ENG	[-5.00 to 5.50 / 0.00 / 0.01V/step]
022	Pixel Correction: C	*ENG
023	Pixel Correction: M	*ENG
024	Pixel Correction: Y	*ENG

3231	[Vtref Limits :Set]
001	Upper:K	*ENG	[0.00 to 5.00 / 4.00 / 0.01V/step]
	Sets upper limit for target value of TD sensor's output voltage: Vtref (K).
002	Upper:C	*ENG	[0.00 to 5.00 / 4.00 / 0.01V/step]
	Sets upper limit for target value of TD sensor's output voltage: Vtref (C).
003	Upper:M	*ENG	[0.00 to 5.00 / 4.00 / 0.01V/step]
	Sets upper limit for target value of TD sensor's output voltage: Vtref (M).
004	Upper:Y	*ENG	[0.00 to 5.00 / 4.00 / 0.01V/step]
	Sets upper limit for target value of TD sensor's output voltage: Vtref (Y).

SP Mode Tables

Main SP Tables-3

011	Lower:K	*ENG	[0.00 to 5.00 / 2.00 / 0.01V/step]
	Sets lower limit for target value of TD sensor's output voltage: Vtref (K).
012	Lower:C	*ENG	[0.00 to 5.00 / 2.00 / 0.01V/step]
	Sets lower limit for target value of TD sensor's output voltage: Vtref (C).
013	Lower:M	*ENG	[0.00 to 5.00 / 2.00 / 0.01V/step]
	Sets lower limit for target value of TD sensor's output voltage: Vtref (M).
014	Lower:Y	*ENG	[0.00 to 5.00 / 2.00 / 0.01V/step]
	Sets lower limit for target value of TD sensor's output voltage: Vtref (Y).

3232	[Vtref Correct:Pixel]
001	ON/OFF	*ENG	[0 or 1 / 1 / 1/step] 0: OFF 1: ON
	Switches ON/OFF pixel Vtref correction.
3232	[Vtref Correct:Pixel]
	Sets coefficient to decide Vtref correction value of Vtref correction by image area. Vtref correction value: SP3-222-009 to 012 = calculated Vtref correction value small area coefficient (This SP) How to use this SP: Vtref correction by image area.
011	Low Coverage Coef:K	*ENG	[0.0 to 5.0 / 1.0 / 0.1/step]
012	Low Coverage Coef:C	*ENG
013	Low Coverage Coef:M	*ENG
014	Low Coverage Coef:Y	*ENG
3232	[Vtref Correct:Pixel]

Main SP Tables-3

	Sets coefficient to decide Vtref correction value of Vtref correction by image area. Vtref correction value: SP3-222-009 to 012 = calculated Vtref correction value large area coefficient (This SP) How to use this SP: Vtref correction by image area.
021	High Coverage Coeff:K	*ENG	[0.0 to 5.0 / 0.5 / 0.1/step]
022	High Coverage Coeff:C	*ENG
023	High Coverage Coeff:M	*ENG
024	High Coverage Coeff:Y	*ENG
3232	[Vtref Correct:Pixel]
040	Initial ProCon Thresh	*ENG	[0 to 255 / 100 / 1times/step]
	Executes Pro-Con by setting a Pro-Con flag when image area cumulative average M (SP3-224-009 to 012) is larger than the specified value and then so deciding that large area images are continuing. When large area images are continuing, specified
041	High Coverage Thresh:H	*ENG	[0 to 100 / 100 / 1%/step]
	How to use this SP: Refer to this SP when printing large area images. When image area accumulate average M (SP3-224-009 to 012) is larger than this SP, judges that high area images are continuing, then set Pro-Con flag and,
050	ProCon Thresh	*ENG	[0 to 255 / 100 / 1times/step]
	Executes Pro-Con by setting a Pro-Con flag when image area total average M (SP3-224-009 to 012) is larger than the specified value and then so deciding that large area images are continuing. When large area images are continuing, specified
060	Low Coverage Thresh	*ENG	[0.0 to 20.0 / 3.0 / 0.1%/step]
	How to use this SP: Refer to this SP when printing small area images. When image area accumulate average L (SP3-224-013 to 016) is less than this SP, judges that low high area images are continuing, then temporarily dis
3232	[Vtref Correct:Pixel]

SP Mode Tables

Main SP Tables-3

	Switches to a mode able to call off Vtref lower limit (Upper limit of TC) by deciding small area images are continuing when image area cumulative average L (SP3-224-013 to 016) is small. This SP
070	TC Upper Limit Correction	*ENG	[0.0 to 5.0 / 0.5 / 0.1wt%/step]
071	TC Upper Limit:Display:Bk	*ENG	[1.0 to 15.0 / 8.5 / 0.1wt%/step]
072	TC Upper Limit:Display:C	*ENG
073	TC Upper Limit:Display:M	*ENG
074	TC Upper Limit:Display:Y	*ENG

3233	[RTP Vtref Corr :Disp/Set]
001	ON/OFF	*ENG	[0 or 1 / 1 / 1/step] 0: OFF 1: ON
001	Controls ON/OFF the Vtref correction done based on RTP pattern deposit amount during print.
3233	[RTP Vtref Corr :Disp/Set]
3233	Sets Vtref correction value (K/C/M/Y) when RTP pattern deposit amount goes over deposit amount threshold (upper/lower limit).
011	Corr Amt(+):K	*ENG	[0.00 to 1.00 / 0.03 / 0.01V/step]
012	Corr Amt(+):C	*ENG
013	Corr Amt(+):M	*ENG
014	Corr Amt(+):Y	*ENG
021	Corr Amt(-):K	*ENG
022	Corr Amt(-):C	*ENG
023	Corr Amt(-):M	*ENG
024	Corr Amt(-):Y	*ENG
3233	[RTP Vtref Corr :Disp/Set]

Main SP Tables-3

	Sets upper/lower limit threshold (K/C/M/Y) of RTP deposit amount.
031	Corr Thresh:K	*ENG	[0.000 to 0.100 / 0.005 / 0.001mg/cm2/step]
032	Corr Thresh:C	*ENG	[0.000 to 0.100 / 0.010 / 0.001mg/cm2/step]
033	Corr Thresh:M	*ENG
034	Corr Thresh:Y	*ENG
3233	[RTP Vtref Corr :Disp/Set]
041	Vtavg Weight Coeff (H)	*ENG	[0 to 100 / 30 / 1%/step]
041	Sets the weight of Vtavg and Vtref used for Vtref Correction Standard Value when Paper Interval Adhesion Amount exceeds Adhesion Amount Threshold (Upper Limit).
051	Vtavg Weight Coeff (M)	*ENG	[0 to 100 / 0 / 1%/step]
051	Sets the weight of Vtavg and Vtref used for Vtref Correction Standard Value when Paper Interval Adhesion Amount exceeds Adhesion Amount Threshold (Lower Limit).
061	Vtavg Weight Coeff (L)	*ENG	[0 to 100 / 5 / 1%/step]
061	Sets the weight of Vtavg and Vtref used for Vtref Correction Standard Value when Paper Interval Adhesion Amount exceeds Adhesion Amount Threshold (Lower Limit).

3234	[Vtref Corr :Disp/Set]
001	ON/OFF	*ENG	[0 or 1 / 1 / 1/step] 0: OFF 1: ON
	Controls ON/OFF Vtref correction of electric potential control.
3234	[Vtref Corr :Disp/Set]
	Set when controlling to keep toner density low with electric potential based on develop gamma. Means Vtref correction (+) side correction amount.
011	Corr Amt(+):K	*ENG	[0.00 to 1.00 / 0.00 / 0.01V/step]

SP Mode Tables

Main SP Tables-3

012	Corr Amt(+):C	*ENG
013	Corr Amt(+):M	*ENG
014	Corr Amt(+):Y	*ENG
3234	[Vtref Corr :Disp/Set]
3234	Set when controlling to keep toner density low with electric potential based on develop gamma. Means Vtref correction (-) side correction amount.
021	Corr Amt(-):K	*ENG	[0.00 to 1.00 / 0.00 / 0.01V/step]
022	Corr Amt(-):C	*ENG
023	Corr Amt(-):M	*ENG
024	Corr Amt(-):Y	*ENG
3234	[Vtref Corr :Disp/Set]
031	P Rank 1 Threshold	*ENG	[0.00 to 2.00 / 0.15 / 0.01/step]
031	Meaning the threshold for P_Rank decision formula below, to decide develop gamma is "High" or "Little High" then the develop gamma target value and develop gamma detection value's diff (delta gamma) among the Vtref correct execution conditions. (Unit:
032	P Rank 2 Threshold	*ENG	[0.00 to 2.00 / 0.05 / 0.01/step]
032	Meaning the threshold for P_Rank decision formula below, to decide develop gamma is "Little High" or "Fair" then the develop gamma target value and develop gamma detection value's diff (delta gamma) among the Vtref correct execution conditions. (Unit:
033	P Rank 3 Threshold	*ENG	[-2.00 to 0.00 / -0.05 / 0.01/step]
033	Meaning the threshold for P_Rank decision formula below, to decide develop gamma is "Little Low" or "Fair" then the develop gamma target value and develop gamma detection value's diff (delta gamma) among the Vtref correct execution conditions. (Unit:
034	P Rank 4 Threshold	*ENG	[-2.00 to 0.00 / -0.15 / 0.01/step]

Main SP Tables-3

	Meaning the threshold for P_Rank decision formula below, to decide develop gamma is "Low" or "Little Low" then the develop gamma target value and develop gamma detection value's diff (delta gamma) among the Vtref correct execution conditions. (Unit:
041	T Rank 1 Threshold	*ENG	[-1.00 to 0.00 / -0.20 / 0.01V/step]
	Threshold to decide toner density as "Deep" or "Fair" by Vt and Vtref's diff (delta Vt) among the Vtref correct execution conditions.
042	T Rank 2 Threshold	*ENG	[0.00 to 1.00 / 0.20 / 0.01V/step]
	Threshold to decide toner density as "Thin" or "Fair" by Vt and Vtref's diff (delta Vt) among the Vtref correct execution conditions.
050	Correction Coefficient	*ENG	[1.0 to 5.0 / 2.0 / 0.1/step]
	Sets correction coefficient for Vtref correction amount.

3250	[ImgArea :Disp]
3250	Displays image area for the latest page.
001	ImgArea:K	*ENG	[0 to 9999 / 0 / 1cm2/step]
002	ImgArea:C	*ENG
003	ImgArea:M	*ENG
004	ImgArea:Y	*ENG

3251	[DotCoverage :Disp]
001	DotCoverage:K	*ENG	[0.00 to 100.00 / 0.00 / 0.01%/step]
	Displays image area rate (K) for the latest page.
002	DotCoverage:C	*ENG	[0.00 to 100.00 / 0.00 / 0.01%/step]
	Displays image area rate (C) for the latest page.
003	DotCoverage:M	*ENG	[0.00 to 100.00 / 0.00 / 0.01%/step]
	Displays image area rate (M) for the latest page.

SP Mode Tables

Main SP Tables-3

004	DotCoverage:Y	*ENG	[0.00 to 100.00 / 0.00 / 0.01%/step]
	Displays image area rate (Y) for the latest page.
011	DC Avg.:S:K	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: S (K)
012	DC Avg.:S:C	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: S (C)
013	DC Avg.:S:M	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: S (M)
014	DC Avg.:S:Y	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: S (Y)
021	DC Avg.:M:K	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: M (K)
022	DC Avg.:M:C	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: M (C)
023	DC Avg.:M:M	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: M (M)
024	DC Avg.:M:Y	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: M (Y)
031	DC Avg.:L:K	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: L (K)
032	DC Avg.:L:C	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: L (C)
033	DC Avg.:L:M	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]
	Displays image area rate cumulative average: L (M)
034	DC Avg.:L:Y	*ENG	[0.00 to 100.00 / 5.00 / 0.01%/step]

Main SP Tables-3

	Displays image area rate cumulative average: L (Y)
041	TotalPage:S:Set	*ENG	[1 to 255 / 10 / 1sheet/step]
	Sets cumulative sheets: S
042	TotalPage:M:Set	*ENG	[1 to 500 / 10 / 1sheet/step]
	Sets cumulative sheets: M
043	TotalPage:L:Set	*ENG	[1 to 999 / 50 / 1sheet/step]
	Sets cumulative sheets: L
051	TotalPage:S:Set	*ENG	[1 to 255 / 20 / 1sheet/step]
	Sets cumulative sheets: S
052	TotalPage:M:Set	*ENG	[1 to 500 / 10 / 1sheet/step]
	Sets cumulative sheets: M
053	TotalPage:S:Set	*ENG	[1 to 999 / 50 / 1sheet/step]
	Sets cumulative sheets: L

3252	[AccumImgArea :Disp]
3252	Displays cumulative image area.
001	ImgArea:K	*ENG	[0 to 65535 / 0 / 1cm^2/step]
002	ImgArea:C	*ENG
003	ImgArea:M	*ENG
004	ImgArea:Y	*ENG

3260	[Temperature/Humidity: Display]
001	Temperature	ENG	[-5.0 to 45.0 / 0.0 / 0.1deg]
	Displays temperature of environment sensor output.
002	Relative Humidity	ENG	[0.0 to 100.0 / 0.0 / 0.1%RH/step]
	Displays relative humidity of environment sensor output.

SP Mode Tables

Main SP Tables-3

003

Absolute Humidity

ENG

[0.00 to 100.00 / 0.00 /

0.01g/m3/step]

Displays absolute humidity of environment sensor output.

3300

[RTP Pattern :Disp]

001

M/A(Latest):K

*ENG

[0.000 to 1.000 / 0.000 /

0.001mg/cm2/step]

Displays latest RTP pattern sensor's deposit amount (K).

002

M/A(Latest):C

*ENG

[0.000 to 1.000 / 0.000 /

0.001mg/cm2/step]

Displays latest RTP pattern sensor's deposit amount (C).

003

M/A(Latest):M

*ENG

[0.000 to 1.000 / 0.000 /

0.001mg/cm2/step]

Displays latest RTP pattern sensor's deposit amount (M).

004

M/A(Latest):Y

*ENG

[0.000 to 1.000 / 0.000 /

0.001mg/cm2/step]

Displays latest RTP pattern sensor's deposit amount (Y).

011

M/A(Target):K

*ENG

[0.000 to 1.000 / 0.220 /

0.001mg/cm2/step]

Displays RTP pattern sensor's depositing target amount (K).

012

M/A(Target):C

*ENG

[0.000 to 1.000 / 0.400 /

0.001mg/cm2/step]

Displays RTP pattern sensor's depositing target amount (C).

013

M/A(Target):M

*ENG

[0.000 to 1.000 / 0.450 /

0.001mg/cm2/step]

Displays RTP pattern sensor's depositing target amount (M).

014

M/A(Target):Y

*ENG

[0.000 to 1.000 / 0.400 /

0.001mg/cm2/step]

Displays RTP pattern sensor's depositing target amount (Y).

Main SP Tables-3

3301	[RTP Pattern :Set]
001	Create Intrvl:BW	ENG	[0 to 200 / 10 / 1pages]
	Sets creating interval (K) for RTP pattern.
002	Create Intrvl:FC	ENG	[0 to 200 / 10 / 1pages]
	Sets creating interval (C) for RTP pattern.
011	Page Cnt:BW	*ENG	[0 to 200 / 0 / 1pages]
	Displays sheets counter value (K) for RTP pattern.
012	Page Cnt:FC	*ENG	[0 to 200 / 0 / 1pages]
	Displays sheets counter value (C) for RTP pattern.
021	M/A UppErr:K	ENG	[0.000 to 1.000 / 0.600 / 0.001mg/cm2/step]
	Sets error decision threshold (K) for SC380 RTP patter error.
022	M/A UppErr:Col	ENG	[0.000 to 2.000 / 1.200 / 0.001mg/cm2/step]
	Sets error decision threshold (CMY) for SC381 to SC383 RTP patter error.
023	M/A LowErr:K	ENG	[0.000 to 1.000 / 0.100 / 0.001mg/cm2/step]
	Sets error decision threshold (K) for SC385 RTP patter error.
024	M/A LowErr:Col	ENG	[0.000 to 1.000 / 0.200 / 0.001mg/cm2/step]
	Sets error decision threshold (CMY) for SC386 to SC388 RTP patter error.
031	Feed Cnt :Set	*ENG	[0 to 99999999 / 50000 / 1ms/step]
	Totals up ON time of sub hopper feed clutch (Reset when toner end sensor detects toner).
041	Feed Cnt :K	*ENG	[0 to 99999999 / 0 / 1 ms/step]
	Totals up ON time of sub hopper feed clutch (K).
042	Feed Cnt :C	*ENG	[0 to 99999999 / 0 / 1 ms/step]

SP Mode Tables

Main SP Tables-3

	Totals up ON time of sub hopper feed clutch (C).
043	Feed Cnt :M	*ENG	[0 to 99999999 / 0 / 1 ms/step]
043	Totals up ON time of sub hopper feed clutch (M).
044	Feed Cnt :Y	*ENG	[0 to 99999999 / 0 / 1 ms/step]
044	Totals up ON time of sub hopper feed clutch (Y).v
051	Vsg Detect Intrvl		[0 to 200 / 10 / 1pages/step]
061	Vsg Page Cnt		[0 to 200 / 0 / 1pages/step]
070	LowErr Thresh		[0 to 99 / 3 / 1times/step]
071	LowErr Cnt:K		[0 to 99 / 0 / 1times/step]
072	LowErr Cnt:C
073	LowErr Cnt:M
074	LowErr Cnt:Y
081	M/A(RTP)_Std	*ENG	[0.000 to 1.000 / 0.220 / 0.001mg/cm2/step]
081	Sets standard deposit amount of RTP pattern deposit amount target value (K).
091	M/A Thresh_Upp:K	*ENG	[0.000 to 1.000 / 0.060 / 0.001mg/cm2/step]
091	Sets upper limit threshold of RTP pattern deposit amount target value (K).
092	M/A Thresh_Upp:C	*ENG	[0.000 to 1.000 / 0.050 / 0.001mg/cm2/step]
092	Sets upper limit threshold of RTP pattern deposit amount target value (C).
093	M/A Thresh_Upp:M	*ENG	[0.000 to 1.000 / 0.050 / 0.001mg/cm2/step]
093	Sets upper limit threshold of RTP pattern deposit amount target value (M).
094	M/A Thresh_Upp:Y	*ENG	[0.000 to 1.000 / 0.050 / 0.001mg/cm2/step]
094	Sets upper limit threshold of RTP pattern deposit amount target value (Y).

Main SP Tables-3

101

M/A Thresh_Low:K

*ENG

[0.000 to 1.000 / 0.050 /

0.001mg/cm2/step]

Sets lower limit threshold of RTP pattern deposit amount target value (K).

102

M/A Thresh_Low:C

*ENG

[0.000 to 1.000 / 0.100 /

0.001mg/cm2/step]

Sets lower limit threshold of RTP pattern deposit amount target value (C).

103

M/A Thresh_Low:M

*ENG

[0.000 to 1.000 / 0.100 /

0.001mg/cm2/step]

Sets lower limit threshold of RTP pattern deposit amount target value (M).

104

M/A Thresh_Low:Y

*ENG

[0.000 to 1.000 / 0.100 /

0.001mg/cm2/step]

Sets lower limit threshold of RTP pattern deposit amount target value (Y).

111

Weight Coeff:K

*ENG

[1 to 10 / 1 / 1/step]

Adds weight to leveling process of RTP pattern deposit amount target value (K).

112

Weight Coeff:Col

*ENG

[1 to 10 / 1 / 1/step]

Adds weight to leveling process of RTP pattern deposit amount target value (Col).

3310	[ID.Sens :Voffset]
	Displays specular reflection light output voltage of ID sensor's LED OFF time.
001	Voffset reg (Front)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
002	Voffset reg (Center)	*ENG
003	Voffset reg (Rear)	*ENG
3310	[ID.Sens :Voffset]
	Displays diffuse reflection light output voltage of ID sensor's LED OFF time.
011	Voffset dif (Front)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
012	Voffset dif (Center)	*ENG
013	Voffset dif (Rear)	*ENG

SP Mode Tables

Main SP Tables-3

3310	[ID.Sens :Voffset]
	Displays specular reflection light output voltage of TM_Front sensor's LED OFF time.
021	Voffset TM(Front)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Displays specular reflection light output voltage of TM_Front sensor's LED OFF time.
022	Voffset TM(Center)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Displays specular reflection light output voltage of TM_Center sensor's LED OFF tim
023	Voffset TM(Rear)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Displays specular reflection light output voltage of TM_Rear sensor's LED OFF time.

3311	[ID.Sens :Vmin]
	Displays Black Vmin output of tone pattern.
001	Vmin_K(Front)	*ENG	[0.000 to 5.000 / 0.000 / 0.001V/step]
002	Vmin_K(Center)	*ENG
003	Vmin_K(Rear)	*ENG

3312	[ID.Sens :Vct]
3312	Factory adjust value of ID sensor.
001	Vct_reg(Front)	*ENG	[0.000 to 5.000 / 0.000 / 0.001V/step]
002	Vct_reg(Center)	*ENG
003	Vct_reg(Rear)	*ENG
011	Vct_dif(Front)	*ENG
012	Vct_dif(Center)	*ENG
013	Vct_dif(Rear)	*ENG

Main SP Tables-3

3320	[Vsg Adj: Execute]
001	P Sensor	ENG	[0 or 1 / 0 / 1/step] [Execute]
	Adjusts Vsg.
012	Voffset Threshold	*ENG	[0.00 to 5.00 / 1.00 / 0.01V/step]
	Sets upper limit threshold of Voffset error.
013	Vsg Upper Threshold	*ENG	[0.00 to 5.00 / 4.50 / 0.01V/step]
	Sets upper limit threshold of Vsg adjust error.
014	Vsg Lower Threshold	*ENG	[0.00 to 5.00 / 3.50 / 0.01V/step]
	Sets lower limit threshold of Vsg adjust error.
015	Ifsg UpperLimit	*ENG	[0.0 to 50.0 / 30.0 / 0.1mA/step]
	Sets error decision threshold of SC382 (If upper limit error).
020	Interval :Set	*ENG	[0 to 2000 / 0 / 1page/step]
	Sets Vsg adjusting execute page interval to be decided after or during printing.  Will be executed when Pro-Con or MUSIC decides necessity. (Won't work alone)
021	Page Cnt	*ENG	[0 to 2000 / 0 / 1page/step]
	Displays Page counter for Vsg execute decision.
031	Vsg Error Counter (Front)	*ENG	[0 to 99 / 0 / 1times/step]
	Counts Vsg error.
032	Vsg Error Counter (Center)	*ENG	[0 to 99 / 0 / 1times/step]
	Counts Vsg error.
033	Vsg Error Counter (Rear)	*ENG	[0 to 99 / 0 / 1times/step]
	Counts Vsg error.

3321	[Adjusted Vsg]

SP Mode Tables

Main SP Tables-3

	Displays specular reflection light output of belt background area adjusted Vsg.
001	Vsg reg (Front)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
002	Vsg reg (Center)	*ENG
003	Vsg reg (Rear)	*ENG
3321	[Adjusted Vsg]
	Displays diffuse reflection light output of belt background area adjusted Vsg.
011	Vsg dif (Front)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
012	Vsg dif (Center)	*ENG
013	Vsg dif (Rear)	*ENG
021	Vsg reg(BW)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Displays specular reflection light output of belt background area adjusted Vs
031	Vsg dif(BW)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Displays diffuse reflection light output of belt background area adjusted Vsg.
041	Vsg TM(Front)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Displays specular reflection light output of belt background area adjusted Vsg. (TM_Front sensor)
042	Vsg TM(Center)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Displays specular reflection light output of belt background area adjusted Vsg. (TM_Center sensor)
043	Vsg TM(Rear)	*ENG	[0.00 to 5.50 / 0.00 / 0.01V/step]
	Displays specular reflection light output of belt background area adjusted Vsg. (TM_Rear sensor)

3322	[Adjusted Ifsg]
	LED ampere value for RTP.
001	Ifsg RTP (Front)	*ENG	[0.0 to 50.0 / 10.0 / 0.1mA/step]
002	Ifsg RTP (Center)	*ENG

Main SP Tables-3

003	Ifsg RTP (Rear)	*ENG
3322	[Adjusted Ifsg]
3322	LED ampere value min. value.
011	Ifsg Min (Front)	*ENG	[0.0 to 50.0 / 27.0 / 0.1mA/step]
012	Ifsg Min (Center)	*ENG
013	Ifsg Min (Rear)	*ENG
3322	[Adjusted Ifsg]
3322	LED ampere value for electric potential control;, MUSIC.
021	Ifsg: TM(Front)	*ENG	[0.0 to 50.0 / 10.0 / 0.1mA/step]
022	Ifsg: TM(Center)	*ENG
023	Ifsg: TM(Rear)	*ENG

3323	[Vsg Adj OK?]
	Displays Vsg adjustment result (SP assign for have compatibility with unification model sires)  Left digit: TM/P sensor (R)  Right digit: TM/P sensor (L) Displays result by each sensor from left in R, then L order.
	Code	Result	detail
	0	Did not EXEC.	(SP default)
	1	Succeed	-
	2	ID sensor proofread error	Out of range from Vsg= Vsg_reg(target value)±x.x[V/step]
	3	Offset voltage error	Voffset_reg>Max. or Voffset_dif>Max.
	4	LED Ampere Max. error.	Ifsg>Max.
	5	ID sensor output error.	Vsg< Vsg_reg(error)
	9	Kill	Kill by error of door open, power off.
001	Latest		*ENG	[0 to 999 / 0 / 1/step]

SP Mode Tables

Main SP Tables-3

002	Latest 2	*ENG
003	Latest 3	*ENG
004	Latest 4	*ENG
005	Latest 5	*ENG
006	Latest 6	*ENG
007	Latest 7	*ENG
008	Latest 8	*ENG
009	Latest 9	*ENG
010	Latest 10	*ENG

3330

[ID.Sens Coef :Disp]

001

K2(Latest) (Front)

*ENG

[0.0000 to 5.0000 / 0.0000 /

0.0001/step]

Displays latest value of ID sensor sensitivity correction coefficient: K2.

002

K2(Latest) (Center)

*ENG

[0.0000 to 5.0000 / 0.0000 /

0.0001/step]

Displays latest value of ID sensor sensitivity correction coefficient: K3.

003

K2(Latest) (Rear)

*ENG

[0.0000 to 5.0000 / 0.0000 /

0.0001/step]

Displays latest value of ID sensor sensitivity correction coefficient: K4.

011

K5(Latest) (Front)

*ENG

[0.0000 to 5.0000 / 1.2000 /

0.0001/step]

Displays latest value of ID sensor sensitivity correction coefficient: K5

012

K5(Latest) (Center)

*ENG

[0.0000 to 5.0000 / 1.2000 /

0.0001/step]

Displays latest value of ID sensor sensitivity correction coefficient: K6.

013

K5(Latest) (Rear)

*ENG

[0.0000 to 5.0000 / 1.2000 /

0.0001/step]

Main SP Tables-3

Displays latest value of ID sensor sensitivity correction coefficient: K7.

3331	[ID.Sens Coef :Set]
	Assign (no need with Tomahawk) for having compatibility with unification model sires (Ap/At, Diana, Zeus).
001	K2: Upp Limit Corr	*ENG	[-0.20 to 0.40 / 0.17 / 0.01/step]
002	K2: Lwr Limit Corr	*ENG	[-0.40 to 0.20 / 0.03 / 0.01/step]
003	K2: Upp/Lwr Limit Coef1	*ENG	[0.00 to 1.00 / 0.00 / 0. 01]
3331	[ID.Sens Coef :Set]
004	Kn: Upper	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Sets upper limit valid range of standardization value for specular reflection used for calculating sensitivity correction: K5.
005	Kn: Lower	*ENG	[0.00 to 1.00 / 0.10 / 0.01/step]
	Sets lower limit valid range of standardization value for specular reflection used for calculating sensitivity correction: K5
006	K5: Upper	*ENG	[0.00 to 10.00 / 6.00 / 0.01/step]
	Sets upper limit value of calculated sensitivity correction coefficient: K5.
007	K5: Lower	*ENG	[0.00 to 1.00 / 0.50 / 0.01/step]
	Sets lower limit value of calculated sensitivity correction coefficient: K5.
008	K5: Target Point	*ENG	[0.00 to 1.00 / 0.15 / 0.01/step]
	Sets proofreading point (Kn) of sensitivity correction coefficient: K5.
009	K5: Target Voltage	*ENG	[0.00 to 5.00 / 1.63 / 0.01V/step]
	Sets proofreading point (Kn) of sensitivity correction coefficient: K5.
012	Corrct Coef:C	*ENG	[0.500 to 1.500 / 1.000 / 0.001/step]
	Sets color diff correction coefficient (C) of Delta Vsp_Dif_Dash.
013	Corrct Coef:M	*ENG	[0.500 to 1.500 / 0.996 / 0.001/step]
	Sets color diff correction coefficient (M) of Delta Vsp_Dif_Dash.

SP Mode Tables

Main SP Tables-3

014

Corrct Coef:Y

*ENG

[0.500 to 1.500 / 1.111 / 0.001/step]

Sets color diff correction coefficient (Y) of Delta Vsp_Dif_Dash.

3332	[M/A Calculation]
3332	Assign (no need with Tomahawk) for having compatibility with unification model sires (Ap/At, Diana, Zeus).
001	Corrct Coef:K	*ENG	[0.50 to 2.00 / 1.00 / 0.01/step]
002	Corrct Coef:C	*ENG
003	Corrct Coef:M	*ENG
004	Corrct Coef:Y	*ENG

3333	[ID.Sens TestVal:F]
3333	Shipping test value of ID sensor. Factory inputs using process application. Service personal inputs when on the market.
001	K2: Check	*ENG	[0.000 to 1.000 / 0.516 / 0.001/step]
002	Diffuse Corr	*ENG	[0.75 to 1.35 / 1.00 / 0.01/step]
003	Vct_reg Check:Slope	*ENG	[0.0 to 200.0 / 0.0 / 0.1mV/mA]
004	Vct_reg Check:Xint	*ENG	[0.0 to 25.5 / 0.0 / 0.1mA/step]
005	Vct_dif Check:Slope	*ENG	[0.0 to 200.0 / 0.0 / 0.1mV/mA]
006	Vct_dif Check:Xint	*ENG	[0.0 to 25.5 / 0.0 / 0.1mA/step]

3334	[ID.Sens TestVal:C]
3334	Shipping test value of ID sensor. Factory inputs using process application. Service personal inputs when on the market.
001	K2: Check	*ENG	[0.000 to 1.000 / 0.516 / 0.001/step]
002	Diffuse Corr	*ENG	[0.75 to 1.35 / 1.00 / 0.01/step]
003	Vct_reg Check:Slope	*ENG	[0.0 to 200.0 / 0.0 / 0.1mV/mA]

Main SP Tables-3

004	Vct_reg Check:Xint	*ENG	[0.0 to 25.5 / 0.0 / 0.1mA/step]
005	Vct_dif Check:Slope	*ENG	[0.0 to 200.0 / 0.0 / 0.1mV/mA]
006	Vct_dif Check:Xint	*ENG	[0.0 to 25.5 / 0.0 / 0.1mA/step]

3335	[ID.Sens TestVal:R]
3335	Shipping test value of ID sensor. Factory inputs using process application. Service personal inputs when on the market.
001	K2: Check	*ENG	[0.000 to 1.000 / 0.516 / 0.001/step]
002	Diffuse Corr	*ENG	[0.75 to 1.35 / 1.00 / 0.01/step]
003	Vct_reg Check:Slope	*ENG	[0.0 to 200.0 / 0.0 / 0.1mV/mA/step]
004	Vct_reg Check:Xint	*ENG	[0.0 to 25.5 / 0.0 / 0.1mA/step]
005	Vct_dif Check:Slope	*ENG	[0.0 to 200.0 / 0.0 / 0.1mV/mA/step]
006	Vct_dif Check:Xint	*ENG	[0.0 to 25.5 / 0.0 / 0.1mA/step]

3400	[Toner Supply Type]
	Selects toner supply method.
001	K	*ENG
			[0 to 4 / 4 / 1/step]
002	C	*ENG
			0: Fixed
003	M	*ENG	2: PID
			4: DANC
004	Y	*ENG

3411	[Toner Supply Qty]
	Displays latest value of supply amount calculated from toner supply amount computation formula.
001	K	ENG	[0.0 to 40000.0 / 0.0 / 0.1mg/step]
002	C	ENG
003	M	ENG

SP Mode Tables

3420	[DeveloperWeight]
	Sets amount of developer weight.
001	Total_Weight:K	*ENG	[50 to 2000 / 380 / 1g/step]
002	Total_Weight:CMY	*ENG

3420	[DeveloperWeight]
	Sets amount of developer weight.
001	Total_Weight:K	*ENG	[50 to 2000 / 380 / 1g/step]
002	Total_Weight:CMY	*ENG

3420	[DeveloperWeight]
	Sets amount of developer weight.
001	Total_Weight:K	*ENG	[50 to 2000 / 380 / 1g/step]
002	Total_Weight:CMY	*ENG

3421	[TnrSplyAbility]
3421	Sets toner supply ability from sub hopper to develop unit.
001	K	*ENG	[0.001 to 2.000 / 0.710 / 0.001mg/msec]
002	C	*ENG
003	M	*ENG
004	Y	*ENG
3421	[TnrSplyAbility]
3421	Corrects supply ability based on supplying time per time unit.
011	TnrSplyAbilityCoef1	*ENG	[0.50 to 2.00 / 1.12 / 0.01/step]
012	TnrSplyAbilityCoef2	*ENG	[0.50 to 2.00 / 1.12 / 0.01/step]
013	TnrSplyAbilityCoef3	*ENG	[0.50 to 2.00 / 1.10 / 0.01/step]
014	TnrSplyAbilityCoef4	*ENG	[0.50 to 2.00 / 1.06 / 0.01/step]
015	TnrSplyAbilityCoef5	*ENG	[0.50 to 2.00 / 1.00 / 0.01/step]
016	TnrSplyAbilityCoef6	*ENG	[0.50 to 2.00 / 0.99 / 0.01/step]
017	TnrSplyAbilityCoef7	*ENG	[0.50 to 2.00 / 0.98 / 0.01/step]
018	TnrSplyAbilityCoef8	*ENG	[0.50 to 2.00 / 0.95 / 0.01/step]
019	TnrSplyAbilityCoef9	*ENG
020	TnrSplyAbilityCoef10	*ENG
021	unit time		[0 to 60000 / 3000 / 1msec/step]

3421	[TnrSplyAbility]
3421	Sets toner supply ability from sub hopper to develop unit.
001	K	*ENG	[0.001 to 2.000 / 0.710 / 0.001mg/msec]
002	C	*ENG
003	M	*ENG
004	Y	*ENG
3421	[TnrSplyAbility]
3421	Corrects supply ability based on supplying time per time unit.
011	TnrSplyAbilityCoef1	*ENG	[0.50 to 2.00 / 1.12 / 0.01/step]
012	TnrSplyAbilityCoef2	*ENG	[0.50 to 2.00 / 1.12 / 0.01/step]
013	TnrSplyAbilityCoef3	*ENG	[0.50 to 2.00 / 1.10 / 0.01/step]
014	TnrSplyAbilityCoef4	*ENG	[0.50 to 2.00 / 1.06 / 0.01/step]
015	TnrSplyAbilityCoef5	*ENG	[0.50 to 2.00 / 1.00 / 0.01/step]
016	TnrSplyAbilityCoef6	*ENG	[0.50 to 2.00 / 0.99 / 0.01/step]
017	TnrSplyAbilityCoef7	*ENG	[0.50 to 2.00 / 0.98 / 0.01/step]
018	TnrSplyAbilityCoef8	*ENG	[0.50 to 2.00 / 0.95 / 0.01/step]
019	TnrSplyAbilityCoef9	*ENG
020	TnrSplyAbilityCoef10	*ENG
021	unit time		[0 to 60000 / 3000 / 1msec/step]

3421	[TnrSplyAbility]
3421	Sets toner supply ability from sub hopper to develop unit.
001	K	*ENG	[0.001 to 2.000 / 0.710 / 0.001mg/msec]
002	C	*ENG
003	M	*ENG
004	Y	*ENG
3421	[TnrSplyAbility]
3421	Corrects supply ability based on supplying time per time unit.
011	TnrSplyAbilityCoef1	*ENG	[0.50 to 2.00 / 1.12 / 0.01/step]
012	TnrSplyAbilityCoef2	*ENG	[0.50 to 2.00 / 1.12 / 0.01/step]
013	TnrSplyAbilityCoef3	*ENG	[0.50 to 2.00 / 1.10 / 0.01/step]
014	TnrSplyAbilityCoef4	*ENG	[0.50 to 2.00 / 1.06 / 0.01/step]
015	TnrSplyAbilityCoef5	*ENG	[0.50 to 2.00 / 1.00 / 0.01/step]
016	TnrSplyAbilityCoef6	*ENG	[0.50 to 2.00 / 0.99 / 0.01/step]
017	TnrSplyAbilityCoef7	*ENG	[0.50 to 2.00 / 0.98 / 0.01/step]
018	TnrSplyAbilityCoef8	*ENG	[0.50 to 2.00 / 0.95 / 0.01/step]
019	TnrSplyAbilityCoef9	*ENG
020	TnrSplyAbilityCoef10	*ENG
021	unit time		[0 to 60000 / 3000 / 1msec/step]

Main SP Tables-3

004

ENG

Main SP Tables-3

3421	[TnrSplyAbility]
3421	Sets absolute humidity threshold 1 of supply ability correction.
031	AbsHum Threshold:1	*ENG	[0.0 to 65.0 / 6.0 / 0.1g/m3/step]
032	AbsHum Threshold:2	*ENG	[0.0 to 65.0 / 12.0 / 0.1g/m3/step]
033	AbsHum Threshold:3	*ENG	[0.0 to 65.0 / 24.0 / 0.1g/m3/step]
3421	[TnrSplyAbility]
3421	Corrects supply ability based on absolute humidity.
041	Environ Coef1	*ENG	[0.50 to 2.00 / 1.00 / 0.01/step]
042	Environ Coef2	*ENG
043	Environ Coef3	*ENG
044	Environ Coef4	*ENG

3422	[Tnr Supply Limits :Set]
3422	Sets max. toner supplying rate.
001	Max Supply Rate:K	*ENG	[0 to 255 / 100 / 1%/step]
002	Max Supply Rate:C	*ENG
003	Max Supply Rate:M	*ENG
004	Max Supply Rate:Y	*ENG
3422	[Tnr Supply Limits :Set]
3422	Sets min. supplying time.
011	Min Supply Time: K	*ENG	[0 to 255 / 100 / 1msec/step]
012	Min Supply Time: C	*ENG
013	Min Supply Time: M	*ENG
014	Min Supply Time: Y	*ENG

SP Mode Tables

Main SP Tables-3

3423	[TnrSplyCarryOver :Disp]
3423	Sets toner supplying rate for fixed amount supplying mode.
001	Carry Over:K	*ENG	[0 to 10000 / 0 / 1msec/step]
002	Carry Over:C	*ENG
003	Carry Over:M	*ENG
004	Carry Over:Y	*ENG

3428

[TnrSplyDelay : Setting]

Sets toner supply delay time.

001

Delay

*ENG

[0 to 255 / 0 / 1msec/step]

3429	[TnrSplyPosTime :Disp]
3429	Sets toner supplying rate for fixed amount supplying mode.
001	Latest: K	*ENG	[0 to 20000 / 0 / 1msec/step]
002	Latest: C	*ENG
003	Latest: M	*ENG
004	Latest: Y	*ENG

3431	[DrvTime: Setting]
3431	Sets toner supplying rate for fixed amount supplying mode.
001	Tmon:K	*ENG	[50 to 1000 / 200 / 50msec/step]
002	Tmon:C	*ENG
003	Tmon:M	*ENG
004	Tmon:Y	*ENG

Main SP Tables-3

3432

[DrvTime: Setting]

Sets max. continuous supplying time.

001

DriveTime(max)

*ENG

[0 to 1500 / 800 / 1msec/step]

3440	[Fixed Supply Mode]
3440	Sets toner supplying rate for fixed amount supplying mode.
001	Fixed Rate: K	*ENG	[0 to 100 / 10 / 1%/step]
002	Fixed Rate: C	*ENG
003	Fixed Rate: M	*ENG
004	Fixed Rate: Y	*ENG

3450	[Toner Supply PID: Setting]
3450	Sets supplying coefficient to supply proportion to Vt-Vtref with toner supply control. Uses PID control for toner supply.
001	Vt Proportion: K	*ENG	[0 to 2550 / 50 / 1/step]
002	Vt Proportion: C	*ENG
003	Vt Proportion: M	*ENG
004	Vt Proportion: Y	*ENG
3450	[Toner Supply PID: Setting]
3450	Sets supplying coefficient to supply proportion to output image's pixel (Pxl) with toner supply control. Uses PID control for toner supply.
011	Pixel Proportion: K	*ENG	[0.00 to 2.55 / 0.47 / 0.01/step]
012	Pixel Proportion: C	*ENG
013	Pixel Proportion: M	*ENG
014	Pixel Proportion: Y	*ENG

SP Mode Tables

Main SP Tables-3

3450	[Toner Supply PID: Setting]
3450	Displays current value of pixel proportionality coefficient 2 for supplying coefficient to supply proportion to output image's pixel (Pxl) with toner supply control. Uses PID control for toner supply.
021	Pixel Proportion 2: K	*ENG	[0.00 to 2.55 / 1.00 / 0.01/step]
022	Pixel Proportion 2: C	*ENG
023	Pixel Proportion 2: M	*ENG
024	Pixel Proportion 2: Y	*ENG
3450	[Toner Supply PID: Setting]
3450	Sets supplying coefficient to supply proportion to output image's pixel (Pxl) with toner supply control. Uses PID control for toner supply.
031	Correction Coeffient: 1	*ENG	[0.00 to 2.55 / 1.00 / 0.01/step]
032	Correction Coeffient: 2	*ENG	[0.00 to 2.55 / 0.50 / 0.01/step]
033	Correction Coeffient: 3	*ENG	[0.00 to 2.55 / 0.00 / 0.01/step]
034	Correction Coeffient: 4	*ENG	[0.00 to 2.55 / 0.25 / 0.01/step]
035	Correction Coeffient: 5	*ENG	[0.00 to 2.55 / 0.50 / 0.01/step]
3450	[Toner Supply PID: Setting]
3450	Displays current value of pixel proportionality coefficient 3 for supplying coefficient to supply proportion to output image's pixel (Pxl) with toner supply control. Uses PID control for toner supply.
041	Pixel Proportion 3: K	*ENG	[0.70 to 1.30 / 1.00 / 0.01/step]
042	Pixel Proportion 3: C	*ENG
043	Pixel Proportion 3: M	*ENG
044	Pixel Proportion 3: Y	*ENG
3450	[Toner Supply PID: Setting]
3450	Sets supplying coefficient to supply proportion to output image's pixel (Pxl) with toner supply control. Uses PID control for toner supply.

Main SP Tables-3

051	Correction Value 1	*ENG	[-0.10 to 0.00 / -0.01 / 0.01/step]
052	Correction Value 2	*ENG	[0.00 to 0.10 / 0.01 / 0.01/step]
3450	[Toner Supply PID: Setting]
3450	Sets transformation coefficient transforming pixel (cm^2) to supply amount (g) for supplying proportion to output image's pixel (Pxl) with toner supply control. Uses PID control for toner supply.
061	P_Pxl_Coef_Err	*ENG	[0.00 to 1.00 / 0.35 / 0.01/step]
3450	[Toner Supply PID: Setting]
3450	Sets supplying coefficient to supply proportion to output image's pixel (Pxl) with toner supply control. Uses PID control for toner supply.
071	Vt Integral Control: K	*ENG	[0 to 2550 / 500 / 1/step]
072	Vt Integral Control: C	*ENG
073	Vt Integral Control: M	*ENG
074	Vt Integral Control: Y	*ENG
3450	[Toner Supply PID: Setting]
3450	Sets supplying coefficient to supply in proportion to Diff. accumulate amount of Vt-Vtref with toner supply control. Uses PID control for toner supply.
081	Vt Integral Value: K	*ENG	[-255.00 to 255.00 / 0.00 / 0.01/step]
082	Vt Integral Value: C	*ENG
083	Vt Integral Value: M	*ENG
084	Vt Integral Value: Y	*ENG
3450	[Toner Supply PID: Setting]
3450	Sets supplying coefficient to supply in proportion to Diff. accumulate amount of Vt-Vtref with toner supply control. Uses PID control for toner supply.
091	Vt Sum Times: K	*ENG	[1 to 255 / 20 / 1times/step]
092	Vt Sum Times: C	*ENG
093	Vt Sum Times: M	*ENG

SP Mode Tables

Main SP Tables-3

094

Vt Sum Times: Y

*ENG

3460	[TonerSupply :DANC]
011	Time_Min	*ENG	[0 to 250 / 0 / 1msec/step]
011	Sets DANC min. supplying time.
012	Time_Max	*ENG	[0 to 1000 / 200 / 1msec/step]
012	Sets DANC max. supplying time.
3460	[TonerSupply :DANC]
3460	Sets supplying amount for when creating SMITH model.
022	SMITH_Weight:K	*ENG	[1 to 500 / 140 / 1mg/step]
023	SMITH_Weight:CMY	*ENG	[1 to 500 / 140 / 1mg/step]
3460	[TonerSupply :DANC]
3460	Sets transferring rate for to compensate reverse transfer amount of ANC term (pixel term).
111	Rev_Fix:K	*ENG	[1.00 to 1.50 / 1.00 / 0.01/step]
112	Rev_Fix:C	*ENG
113	Rev_Fix:M	*ENG
114	Rev_Fix:Y	*ENG
3460	[TonerSupply :DANC]
3460	Sets delay time of from toner supplying door to sensor for SMITH model, by control sample count.
121	TnrSplyDelay:StdSpd:K	*ENG	[0 to 200 / 7 / 1/step]
122	TnrSplyDelay:MidSpd:K	*ENG	[0 to 200 / 13 / 1/step]
123	TnrSplyDelay:LowSpd:K	*ENG	[0 to 200 / 19 / 1/step]
131	TnrSplyDelay:StdSpd:CMY	*ENG	[0 to 200 / 7 / 1/step]
132	TnrSplyDelay:MidSpd:CMY	*ENG	[0 to 200 / 13 / 1/step]
133	TnrSplyDelay:LowSpd:CMY	*ENG	[0 to 200 / 19 / 1/step]

Main SP Tables-3

3461	[TonerSupply :DANC]
001	PI:Power	*ENG	[5 to 200 / 100 / 1%/step]
	Changes all demand value of PI term.
011	PI:P Gain:K	*ENG	[0.0000 to 1.0000 / 0.0100 / 0.0001/step]
	Sets P gain (K).
012	PI:P Limits:Up:K	*ENG	[0.00 to 1.00 / 0.10 / 0.01/step]
	Sets limit against P term demanding value. (Supply plus side, K)
013	PI:P Limits:Low:K	*ENG	[0.00 to 1.00 / 0.10 / 0.01/step]
	Sets limit against P term demanding value. (Supply minus side, K)
021	PI:I Gain:K	*ENG	[0.0000 to 1.0000 / 0.0010 / 0.0001/step]
	Sets I gain (K).
022	PI:I Limits:Up:K	*ENG	[0.00 to 1.00 / 0.10 / 0.01/step]
	Sets limit against I term demanding value. (Supply plus side, K)
023	PI:I Limits:Low:K	*ENG	[0.00 to 1.00 / 0.10 / 0.01/step]
	Sets limit against I term demanding value. (Supply minus side, K)
031	PI:P Gain:CMY	*ENG	[0.0000 to 1.0000 / 0.0100 / 0.0001/step]
	Sets P gain (CMY).
032	PI:P Limits:Up:CMY	*ENG	[0.00 to 1.00 / 0.10 / 0.01/step]
	Sets limit against P term demanding value. (Supply plus side, CMY)
033	PI:P Limits:Low:CMY	*ENG	[0.00 to 1.00 / 0.10 / 0.01/step]
	Sets limit against P term demanding value. (Supply minus side, CMY)
041	PI:I Gain:CMY	*ENG	[0.0000 to 1.0000 / 0.0010 / 0.0001/step]

SP Mode Tables

Main SP Tables-3

	Sets I gain (CMY).
042	PI:I Limits:Up:CMY	*ENG	[0.00 to 1.00 / 0.10 / 0.01/step]
	Sets limit against I term demanding value. (Supply plus side, CMY)
043	PI:I Limits:Low:CMY	*ENG	[0.00 to 1.00 / 0.10 / 0.01/step]
	Sets limit against I term demanding value. (Supply minus side, CMY)
051	AW:AWIlow:K	*ENG	[0 to 10000 / 100 / 1/step]
	Sets AW gain (K). (Normally reciprocal of P gain)
052	AW:AWIpni:K	*ENG	[0 to 2000 / 1000 / 1/step]
	Sets rate to rapidly decrease accumulate value of difference between toner density and target value. (K: Supply plus side)
061	AW:AWIlow:CMY	*ENG	[0 to 10000 / 100 / 1/step]
	Sets AW gain (CMY). (Normally reciprocal of P gain)
062	AW:AWIpni:CMY	*ENG	[0 to 2000 / 1000 / 1/step]
	Sets rate to rapidly decrease accumulate value of difference between toner density and target value. (CMY: Supply plus side)
3461	[TonerSupply :DANC]
	Corrects line speed for demand value of PI term.
102	PI:LineSpdCoef:MidSpd:K	*ENG	[0.05 to 1.00 / 0.50 / 0.01/step]
103	PI:LineSpdCoef:LowSpd:K	*ENG
112	PI:LineSpdCoef:StdSpd:CMY	*ENG
113	PI:LineSpdCoef:LowSpd:CMY	*ENG
3461	[TonerSupply :DANC]
121	SMITH:Gain:K	*ENG	[0.00 to 2.00 / 1.00 / 0.01/step]
	Changes gain (amplitude of model) for SMITH model. (K)
122	SMITH:MidSpd:K	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Corrects line speed for gain of SMITH model. (Middle speed, K)

Main SP Tables-3

123	SMITH:LowSpd:K	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Corrects line speed for gain of SMITH model. (Low speed, K)
131	SMITH:Gain:CMY	*ENG	[0.00 to 2.00 / 1.00 / 0.01/step]
	Changes gain (amplitude of model) for SMITH model. (CMY)
132	SMITH:MidSpd:CMY	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Corrects line speed for gain of SMITH model. (Middle speed, CMY)
133	SMITH:LowSpd:CMY	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Corrects line speed for gain of SMITH model. (Low speed, CMY)

3462	[TonerSupply :DANC]
001	ANC:Power	*ENG	[0 to 200 / 100 / 1%/step] 100: Standard control 0: No ANC
	Changes all ANC filters demand value of ANC term.
101	ANC:Gain:K	*ENG	[0.00 to 2.00 / 1.00 / 0.01/step]
	Sets gain for all ANC filters. (K)
102	ANC:MidSpd:K	*ENG	[0.05 to 1.00 / 1.00 / 0.01/step]
	Corrects line speed for gain of all ANC filters. (Middle speed, K)
103	ANC:LowSpd:K	*ENG	[0.05 to 1.00 / 1.00 / 0.01/step]
	Corrects line speed for gain of all ANC filters. (Low speed, K)
111	ANC:Gain:CMY	*ENG	[0.00 to 2.00 / 1.00 / 0.01/step]
	Sets gain for all ANC filters. (CMY)
112	ANC:MidSpd:CMY	*ENG	[0.05 to 1.00 / 1.00 / 0.01/step]
	Corrects line speed for gain of all ANC filters. (Middle speed, CMY)
113	ANC:LowSpd:CMY	*ENG	[0.05 to 1.00 / 1.00 / 0.01/step]
	Corrects line speed for gain of all ANC filters. (Low speed, CMY)

SP Mode Tables

Main SP Tables-3

3463	[TonerSupply :DANC]
3463	Saves I term corresponding to power OFF/ON.
101	Int:I:K	*ENG	[-1000.0000 to 1000.0000 / 0.0000 / 0.0001/step]
102	Int:I:C	*ENG
103	Int:I:M	*ENG
104	Int:I:Y	*ENG
3463	[TonerSupply :DANC]
3463	Saves ANC term (pixel term) corresponding to power OFF/ON.
111	ANC:ref Sum:K	*ENG	[-1000.0000 to 1000.0000 / 0.0000 / 0.0001/step]
112	ANC:ref Sum:C	*ENG
113	ANC:ref Sum:M	*ENG
114	ANC:ref Sum:Y	*ENG
3463	[TonerSupply :DANC]
3463	Displays image area for the latest page.
201	ImgArea:K	*ENG	[0 to 9999 / 0 / 1cm2/step]
202	ImgArea:C	*ENG
203	ImgArea:M	*ENG
204	ImgArea:Y	*ENG

3500

[ImgQltyAdj :ON/OFF]

001

ALL

*ENG

[0 or 1 / 1 / 1/step]

0: OFF

1: ON

Sets execution judge to OFF of all imaging system adjustments.

002

ProCon

*ENG

[0 or 1 / 1 / 1/step]

0: OFF

1: ON

Main SP Tables-3

	Sets execution judge to OFF of electric potential control.
003	MUSIC Condition:Auto Exe	*ENG	[0 or 1 / 1 / 1/step]
	Forcedly sets MUSIC auto execution to OFF.
004	Init TD Sensor	*ENG	[0 or 1 / 1 / 1/step] 0: OFF 1: ON
	Sets execution judge to OFF for initial setting of TD sensor.

3510	[ImgQltyAdj :ExeFlag]
3510	Sets execution flag for toner recovery (Executes toner recovery with setting to "1" and power OFF/ON, or close front cover.)
001	Toner Recovery: K	*ENG	[0 to 3 / 0 / 1/step]
002	Toner Recovery: C	*ENG
003	Toner Recovery: M	*ENG
004	Toner Recovery: Y	*ENG
3510	[ImgQltyAdj :ExeFlag]
3510	Sets execution flag for initial setting of TD sensor. (TD sensor's initial setting will be executed by setting to "1" and power OFF/ON)
011	Init TD Sensor :K	*ENG	[0 or 1 / 0 / 1/step]
012	Init TD Sensor :C	*ENG
013	Init TD Sensor :M	*ENG
014	Init TD Sensor :Y	*ENG
3510	[ImgQltyAdj :ExeFlag]
021	Process Control	*ENG	[0 to 2 / 0 / 1/step]
021	Sets execution flag for Pro-Con (Executes Pro-Con with setting to "1" and power OFF/ON, or close front cover.)
022	Developer Agitating	*ENG	[0 or 1 / 0 / 1/step]

SP Mode Tables

Main SP Tables-3

	Sets execution flag for developer stir (Executes developer stir with setting to "1" and power OFF/ON, or close front cover.)
023	Blade Damage Prevention	*ENG	[0 or 1 / 0 / 1/step]
	Sets execution flag for blade burr prevent mode (Executes blade burr prevent mode with setting to "1" and power OFF/ON or closing front cover.)
024	MUSIC	*ENG	[0 to 3 / 0 / 1/step] 0: OFF 1: Mode:b 2: Mode:a 3: Mode:e
	Sets execution flag for MUSIC (MUSIC (1time) with setting "1" and power OFF/ON or closing font cover, MUSIC (2times) with setting "2", real time MUSIC with setting "3")
025	Vsg Adj.	*ENG	[0 or 1 / 0 / 1/step]
	Sets execution flag for Vsg adjust (Executes Vsg adjust with setting to "1" and power OFF/ON, or close front cover.)
026	Charge AC Adj.	*ENG	[0 or 1 / 0 / 1/step]
	Sets execution flag for Electrify roller cleaning (K) (Executes Electrify roller cleaning (K) with setting to "1" and power OFF/ON, or close from cover.)
3510	[ImgQltyAdj :ExeFlag]
031	Init Toner Replenish: K	*ENG	[0 or 1 / 0 / 1/step]
	Sets execution flag for toner initial filler (K) (Executes toner recovery (K) with setting to "1" and power OFF/ON, or close front cover.)
032	Init Toner Replenish: C	*ENG	[0 or 1 / 0 / 1/step]
	Sets execution flag for toner initial filler (C) (Executes toner recovery (C) with setting to "1" and power OFF/ON, or close front cover.)
033	Init Toner Replenish: M	*ENG	[0 or 1 / 0 / 1/step]
	Sets execution flag for toner initial filler (M) (Executes toner recovery (M) with setting to "1" and power OFF/ON, or close front cover.)
034	Init Toner Replenish: Y	*ENG	[0 or 1 / 0 / 1/step]

Main SP Tables-3

	Sets execution flag for toner initial filler (Y) (Executes toner recovery (Y) with setting to "1" and power OFF/ON, or close front cover.)
041	DEMS		[0 or 1 / 0 / 1/step]
042	IBACC	*ENG	[0 or 1 / 0 / 1/step]
	Sets execution flag for toner initial filler (Y) (Executes toner recovery (Y) with setting to "1" and power OFF/ON, or close front cover.)
043	Vsg in TrnsBlt:corr	*ENG	[0 or 1 / 0 / 1/step]
	Sets execution flag for toner initial filler (Y) (Executes toner recovery (Y) with setting to "1" and power OFF/ON, or close front cover.)
044	Dev. AC Adj.	*ENG	[0 or 1 / 0 / 1/step]
	Sets execution flag for develop AC adjust (Executes with setting to "1" and power OFF/ON, or close from cover.)
045	BIT1	*ENG	[0 or 1 / 0 / 1/step]
	Execution flag for image adjust of BIT 1 control.

3520	[ImgQltyAdj :Interval]
001	During Job	*ENG	[0 to 100 / 30 / 1page/step]
	Sets image adjust judgment page interval for during print.
002	During Stand-by	*ENG	[0 to 100 / 5 / 1minute/step]
	Sets image adjust judgment time interval for during standby.

3521	[Drum Stop Time :Disp]
3521	Displays finish imaging time.
001	Year	*ENG	[0 to 99 / 0 / 1year/step]
002	Month	*ENG	[1 to 12 / 1 / 1month/step]
003	Day	*ENG	[1 to 31 / 1 / 1day/step/step]
004	Hour	*ENG	[0 to 23 / 0 / 1hour/step]
005	Minute	*ENG	[0 to 59/ 0 / 1 minutes/step]

SP Mode Tables

Main SP Tables-3

3522	[Drum Stop Environ :Disp]
001	Temperature	*ENG	[-1280.0 to 1270.0 / 0.0 / 0.1deg]
	Displays (temperature) of when imaging finished.
002	Rel Humidity	*ENG	[0.0 to 1000.0 / 0.0 / 0.1%RH/step]
	Displays (relative humidity) of when imaging finished.
003	Abs Humidity	*ENG	[0.0 to 1000.0 / 0.0 / 0.1g/m3/step]
	Displays (absolute humidity) of when imaging finished.

3529	[ProCon Interval Control :Set]
001	Gamma Corr	*ENG	[0 or 1 / 1 / 1/step] 0: OFF 1: ON
	Sets ON/OFF develop gamma correction for Pro-Con auto execute interval.
002	Environ Corr	*ENG	[0 or 1 / 1 / 1/step] 0: OFF 1: ON
	Sets ON/OFF environment correction for Pro-Con auto execute interval.
003	AbsHum Threshhold	*ENG	[0.0 to 99.0 / 4.3 / 0.1g/m3/step]
	Sets absolute humidity threshold of environment correction for Pro-Con auto execute interval.
004	Max Cnt Threshhold	*ENG	[0 to 99 / 2 / 1counts/step]
	Sets max. count threshold of Interrupt Pro-Con/Job end Pro-Con.
005	Exe Cnt	ENG	[0 to 255 / 0 / 1counts/step]
	Sets max. count counter of Interrupt Pro-Con/Job end Pro-Con.
006	Page Cnt:BW	*ENG	[0 to 5000 / 0 / 1sheet/step]
	Displays Pro-Con (BW) sheets count.
007	Page Cnt:FC	*ENG	[0 to 5000 / 0 / 1sheet/step]

Main SP Tables-3

Displays Pro-Con (FC) sheets count.

3530	[PowerON ProCon :Se]
001	Non-use Time Setting	*ENG	[0 to 1440 / 360 / 1minute/step]
	Sets Pro-Con execute judgment threshold of when Power ON.
002	Temperature Range	*ENG	[0 to 99 / 10 / 1deg/step]
	Sets Pro-Con execute judgment threshold of when Power ON.
003	Relative Humidity Range	*ENG	[0 to 99 / 50 / 1%RH/step]
	Sets Pro-Con execute judgment threshold of when Power ON.
004	Absolute Humidity Range	*ENG	[0 to 99 / 6 / 1g/m3/step]
	Sets Pro-Con execute judgment threshold of when Power ON.
005	Interval:BW	*ENG	[0 to 5000 / 250 / 1sheet/step]
	Sets Pro-Con execute judgment threshold of when Power ON.
006	Interval:FC	*ENG	[0 to 5000 / 100 / 1sheet/step]
	Sets Pro-Con execute judgment threshold of when Power ON.
007	Page Cnt:BW	*ENG	[0 to 5000 / 0 / 1 sheet/step]
	Sets sheets count for Power ON Pro-Con (BW).
008	Page Cnt:FC	*ENG	[0 to 5000 / 0 / 1 sheet/step]
	Sets sheets count for Power ON Pro-Con (FC).

3531	[Non-useTime Procon :Set]
3531	Sets Pro-Con execute judgment threshold for during standby.
001	Non-use Time Setting	*ENG	[0 to 1440 / 360 / 1minute/step]
002	Temperature Range	*ENG	[0 to 99 / 10 / 1deg/step]
003	Relative Humidity Range	*ENG	[0 to 99 / 50 / 1%RH/step]
004	Absolute Humidity Range	*ENG	[0 to 99 / 6 / 1g/m3/step]

SP Mode Tables

Main SP Tables-3

3531

[Non-useTime Procon :Set]

Sets upper limit of continuously executing count for Pro-Con during standby.

005

Maximum Execution Number

*ENG

[0 to 99 / 10 / 1times/step]

3533	[Interrupt ProCon :Set]
001	Interval:Set:BW	*ENG	[0 to 5000 / 500 / 1sheet/step]
	Sets number of sheets interval for Interrupt Pro-Con (BW).
002	Interval:Disp:BW	*ENG	[0 to 5000 / 500 / 1sheet/step]
	Displays number of sheets interval for Interrupt Pro-Con (BW).
003	Corr(Short):BW	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Sets correcting coefficient (Short) of number of sheets interval for Interrupt Pro-Con (BW).
004	Corr(Mid):BW	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Sets correcting coefficient (Mid) of number of sheets interval for Interrupt Pro-Con (BW).
011	Interval:Set:FC	*ENG	[0 to 5000 / 200 / 1sheet/step]
	Sets number of sheets interval for Interrupt Pro-Con (FC).
012	Interval:Disp:FC	*ENG	[0 to 5000 / 200 / 1sheet/step]
	Displays number of sheets interval for Interrupt Pro-Con (FC).
013	Corr(Short):FC	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Sets correcting coefficient (Short) of number of sheets interval for Interrupt Pro-Con (FC).
014	Corr(Mid):FC	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Sets correcting coefficient (Mid) of number of sheets interval for Interrupt Pro-Con (FC).

Main SP Tables-3

3534	[JobEnd ProCon :Set]
001	Interval:Set:BW	*ENG	[0 to 5000 / 500 / 1sheet/step]
	Sets number of sheets interval for Job end Pro-Con (BW).
002	Interval:Disp:BW	*ENG	[0 to 5000 / 500 / 1sheet/step]
	Displays number of sheets interval for Job end Pro-Con (BW).
003	Corr(Short):BW	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Sets correcting coefficient (Short) of number of sheets interval for Job end Pro-Con (BW).
004	Corr(Mid):BW	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Sets correcting coefficient (Mid) of number of sheets interval for Job end Pro-Con (BW).
011	Interval:Set:FC	*ENG	[0 to 1000 / 200 / 1sheet/step]
	Sets number of sheets interval for Job end Pro-Con (FC).
012	Interval:Disp:FC	*ENG	[0 to 5000 / 200 / 1sheet/step]
	Displays number of sheets interval for Job end Pro-Con (FC).
013	Corr(Short):FC	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Sets correcting coefficient (Short) of number of sheets interval for Job end Pro-Con (FC).
014	Corr(Mid):FC	*ENG	[0.00 to 1.00 / 1.00 / 0.01/step]
	Sets correcting coefficient (Mid) of number of sheets interval for Job end Pro-Con (FC).

3539	[Dev Agitating Time :Set]
001	Time	*ENG	[0 to 3000 / 10 / 1sec/step]
	Sets Developer Agitating Time.
010	ON/OFF(by RelHum)	*ENG	[0 or 1 / 1 / 1/step]
	Sets ON/OFF for Absolute Humidity Correction for Developer Agitating Time.

SP Mode Tables

Main SP Tables-3

3539	[Dev Agitating Time :Set]
3539	Sets stirring time based on relative humidity of developer stirring time.
011	by RelHum:1	*ENG	[0 to 3000 / 0 / 1sec/step]
012	by RelHum:2	*ENG	[0 to 3000 / 5 / 1sec/step]
013	by RelHum:3	*ENG
014	by RelHum:4	*ENG
015	by RelHum:5	*ENG
016	by RelHum:6	*ENG
021	RelHum Threshold:1	*ENG	[0 to 1000 / 4 / 1%RH/step]
022	RelHum Threshold:2	*ENG	[0 to 1000 / 8 / 1%RH/step]
023	RelHum Threshold:3	*ENG	[0 to 1000 / 12 / 1%RH/step]
024	RelHum Threshold:4	*ENG	[0 to 1000 / 16 / 1%RH/step]
025	RelHum Threshold:5	*ENG	[0 to 1000 / 24 / 1%RH/step]
3539	[Dev Agitating Time :Set]
030	ON/OFF(by Non-use Time)	*ENG	[0 or 1 / 1 / 1/step]
030	Sets ON/OFF exposure time correction of developer stirring time.
031	by Non-use Time:1		[0 to 3000 / 0 / 1sec/step]
032	by Non-use Time:2
033	by Non-use Time:3
034	by Non-use Time:4
035	by Non-use Time:5
036	by Non-use Time:6
037	by Non-use Time:7
038	by Non-use Time:8
039	by Non-use Time:9
040	by Non-use Time:10

Main SP Tables-3

041	Non-use Time Threshhold:1		[0 to 5000 / 15 / 1min/step]
042	Non-use Time Threshhold:2		[0 to 5000 / 30 / 1min/step]
043	Non-use Time Threshhold:3		[0 to 5000 / 60 / 1min/step]
044	Non-use Time Threshhold:4		[0 to 5000 / 120 / 1min/step]
045	Non-use Time Threshhold:5		[0 to 5000 / 240 / 1min/step]
046	Non-use Time Threshhold:6		[0 to 5000 / 360 / 1min/step]
047	Non-use Time Threshhold:7		[0 to 5000 / 720 / 1min/step]
048	Non-use Time Threshhold:8		[0 to 5000 / 1440 / 1min/step]
049	Non-use Time Threshhold:9		[0 to 5000 / 2880 / 1min/step]
050	ON/OFF(by Non-use Time)	*ENG	[0 or 1 / 1 / 1/step]
050	Sets ON/OFF image area correction of developer stirring time.
3539	[Dev Agitating Time :Set]
3539	Sets stirring time based on image area of developer stirring time.
051	by DotCoverage :1	*ENG	[0 to 3000 / 0 / 1sec/step]
052	by DotCoverage :2	*ENG	[0 to 3000 / 0 / 1sec/step]
053	by DotCoverage :3	*ENG	[0 to 3000 / 5 / 1sec/step]
054	by DotCoverage :4	*ENG
055	by DotCoverage :5	*ENG
056	by DotCoverage :6	*ENG
3539	[Dev Agitating Time :Set]
3539	Sets image area threshold of developer stirring time.
061	DotCoverage Threshhold:1	*ENG	[0 to 5000 / 10 / 1min/step]
062	DotCoverage Threshhold:2	*ENG	[0 to 5000 / 20 / 1min/step]
063	DotCoverage Threshhold:3	*ENG	[0 to 5000 / 30 / 1min/step]
064	DotCoverage Threshhold:4	*ENG	[0 to 5000 / 40 / 1min/step]
065	DotCoverage Threshhold:5	*ENG	[0 to 5000 / 50 / 1min/step]

SP Mode Tables

Main SP Tables-3

3539

[Dev Agitating Time :Set]

099

UpperLimit

*ENG

[0 to 3600 / 3600 / 1sec/step]

Sets upper limit of developer stirring time.

3540	[PowerON Music :Set]
	Sets sheets count for Power ON MUSIC.
001	Page Cnt:BW	*ENG	[0 to 5000 / 0 / 1sheet/step]
002	Page Cnt:FC	*ENG

3541	[Music Interval :Set]
	Sets sheets count for Power ON MUSIC.
001	Page Cnt:BW	*ENG	[0 to 5000 / 0 / 1sheet/step]
002	Page Cnt:FC	*ENG
3541	[Realtime Music Interval :Set]
	Saves / Updates this SP with print count in B&W + color mode since the last MUSIC for to use with real time MUSIC.
003	Page Cnt:BW+FC	*ENG	[0 to 5000 / 0 / 1sheet/step]

3550	[Refresh Mode]
	Display image area needs to be refreshed. Consumes toner with density adjust or when print finished if this value is larger than set.
001	Required Area: K	*ENG	[0 to 65535 / 0 / 1cm^2]
002	Required Area: C	*ENG
003	Required Area: M	*ENG
004	Required Area: Y	*ENG
3550	[Refresh Mode]
	Uses for to calculate discharge amount when discharging toner at end of print.

Main SP Tables-3

011	Dev. Unit Rotation: Display: Bk	*ENG	[0.0 to 1000.0 / 0.0 / 0.1m/step]
012	Dev. Unit Rotation: Display: C	*ENG
013	Dev. Unit Rotation: Display: M	*ENG
014	Dev. Unit Rotation: Display: Y	*ENG
3550	[Refresh Mode]
021	Rotation Threshold	*ENG	[0.0 to 1000.0 / 0.1 / 0.1m/step]
021	Uses for execute judging of discharging toner at end of print.
3550	[Refresh Mode]
3550	Uses for to calculate discharge amount when discharging toner at end of print. With increasing the value, more will be discharged.
031	Reflesh Threshold: Bk	*ENG	[0 to 255 / 17 / 1cm^2/step]
032	Reflesh Threshold: C	*ENG
033	Reflesh Threshold: M	*ENG
034	Reflesh Threshold: Y	*ENG
3550	[Refresh Mode]
035	Mode Selection Coefficient	ENG	[0 or 1 / 1 / 1/step]
035	Uses for to calculate discharge amount when discharging toner at end of print.
3550	[Refresh Mode]
3550	Uses for to calculate discharge amount when discharging toner at end of print. With increasing the value, more will be discharged.
041	Job End Area Coefficient:K	*ENG	[0.1 to 25.5 / 1.0 / 0.1/step]
042	Job End Vb Coefficient:K	*ENG	[0 to 100 / 40 / 1%/step]
043	Job End Length:K	*ENG	[0 to 255 / 25 / 1mm/step]
044	Job End Supply	*ENG	[0.000 to 1.000 / 0.450 / 0.001mg/cm^2]

SP Mode Tables

Main SP Tables-3

045	Job End Area Coefficient:YMC	*ENG	[0.1 to 25.5 / 1.0 / 0.1/step]
046	Job End Vb Coefficient:YMC	*ENG	[0 to 100 / 40 / 1%/step]
047	Job End Length:YMC	*ENG	[0 to 255 / 25 / 1mm/step]
3550	[Refresh Mode]
081	TC Adj. Consume(Upp Limit)	*ENG	[0 to 255 / 20 / 1times/step]
081	Sets consume counts (upper limit) for toner density adjusting Pro-Con.

3552

[Blade damage prevention mode]

001

Execution Temp. Threshold

*ENG

[0 to 50 / 40 / 1deg/step]

Sets temperature threshold for creating blade Tear off prevent pattern.

3553

[Transfer belt cleaning]

001

TransferIdleTime Temperature:H

*ENG

[0.0 to 3.0 / 0.0 /

0.1revolutions/step]

Prevents poor cleaning by racing the image transfer when going over temperature threshold t2 and poor cleaning occurred right after Pro-Con/MUSIC etc... adjust pattern was entered.

002

TransferIdleTime Temperature:M

*ENG

[0.0 to 3.0 / 0.0 /

0.1revolutions/step]

Prevents poor cleaning by racing the image transfer when between temperature threshold t1to t2 and poor cleaning occurred right after Pro-Con/MUSIC etc... adjust pattern was entered.

003

TransferIdleTime Temperature:L

*ENG

[0.0 to 3.0 / 0.0 /

0.1revolutions/step]

Prevents poor cleaning by racing the image transfer when smaller than temperature threshold t1 and poor cleaning occurred right after Pro-Con/MUSIC etc... adjust pattern was entered.

004

TransferIdleTime Temperature:L:ON

*ENG

[0.0 to 3.0 / 0.0 /

0.1revolutions/step]

Main SP Tables-3

	Prevents poor cleaning by racing the image transfer when smaller than temperature threshold t1 and poor cleaning occurred right after Pro-Con/MUSIC etc... adjust pattern was entered when starting up machine fist in the morning.
005	Temperature Threshold:T2	*ENG	[20 to 30 / 25 / 1deg/step]
	Adjusts temperature threshold of poor cleaning to occur after Pro-Con/MUSIC etc... adjusting pattern was entered.
006	Temperature Threshold:T1	*ENG	[0 to 15 / 15 / 1deg/step]
	Adjusts temperature threshold of poor cleaning to occur after Pro-Con/MUSIC etc... adjusting pattern was entered.
007	Temperature Threshold:T3	*ENG	[0 to 30 / 5 / 1deg/step]
	Adjusts threshold for wide stripes to occur in the image of the next job caused by image transfer belt cleaning after job stops.

3554	[TransBltCleanBladeReplMode:Exe]
001	Execute	ENG	[0 or 1 / 0 / 1/step]
	Executes replace mode of paper transfer cleaning blade. * Specification unapplied SP, No use.
002	Idle Time	ENG	[0.1 to 60.0 / 10.0 / 0.1sec/step]
	Sets paper transfer racing time for when replace mode of paper transfer cleaning blade. * Specification unapplied SP, No use.

3555

[ImageQuality Adj. Counter:Disp]

001

Charge AC Control

*ENG

[0 to 2000 / 0 / 1page/step]

For to use with adjusting control of electrify AC bias.

3600

[Select ProCon]

001

Potential Control

*ENG

[0 or 1 / 1 / 1/step]

0: OFF

1: ON

SP Mode Tables

Main SP Tables-3

Sets electric potential control method.

002

LD Control

*ENG

[0 to 3 / 1 / 1/step]

0: OFF

1: ON

Sets LD control method.

003

TC Adj. Mode

*ENG

[0 to 3 / 3 / 1/step] 0: Do Not Execute 1: 1st Power On

2: 1st Power On & Job End 3: 1st P_On & JE &printing

Sets Execution timing of toner density adjusting Pro-Con.

004

ACC Before ProCon

*ENG

[0 to 3 / 2 / 1/step]

0: NotExecute

1: ProcessControl

2: TCContorol

Executes same action as Pro-Con executed before ACC, from SP.

006

Pattern Cal. Method

*ENG

[0 to 3 / 0 / 1/step]

0: FIXED

1: INITIALIZED

2: CALCULATED

Executes same action as Pro-Con executed before ACC, from SP.

010

ActivePotentialControl

*ENG

[0 or 1 / 1 / 1/step]

0: OFF

1: ON

Sets electric potential control method for during printing.

030

IBACC:ON/OFF

*ENG

[0 or 1 / 1 / 1/step]

0: OFF

1: ON

Sets execute ON/OFF of IBACC.

060

Vsg ITB Internal Circumference Correction

*ENG

[0 or 1 / 1 / 1/step]

0: OFF

1: ON

Main SP Tables-3

Sets execute ON/OFF of Vsg paper transfer internal rotate correction.

3610	[Chrg AC Control]
3610	Displays electrify AC control value decided with electrify AC control.
001	Std Speed: K	*ENG	[0.00 to 3.00 / 2.20 / 0.01kV]
002	Std Speed: C	*ENG
003	Std Speed: M	*ENG
004	Std Speed: Y	*ENG

3611	[Chrg DC Control]
3611	Displays electrify DC bias decided with Pro-Con.
001	Std Speed: K	*ENG	[300 to 1000 / 690 / 1-V/step]
002	Std Speed: C	*ENG
003	Std Speed: M	*ENG
004	Std Speed: Y	*ENG
011	Mid Speed: K	*ENG
012	Mid Speed: C	*ENG
013	Mid Speed: M	*ENG
014	Mid Speed: Y	*ENG
021	Low Speed: K	*ENG
022	Low Speed: C	*ENG
023	Low Speed: M	*ENG
024	Low Speed: Y	*ENG
3611	[Chrg DC Control]
3611	Displays electrify DC bias decided with Pro-Con.
031	Std Speed: K (Front)		[300 to 1000 / 690 / 1-V/step]

SP Mode Tables

Main SP Tables-3

032	Std Speed: C (Front)	[300 to 1000 / 690 / 1-V/step]
033	Std Speed: M (Front)	[300 to 1000 / 690 / 1-V/step]
034	Std Speed: Y (Front)	[300 to 1000 / 690 / 1-V/step]
041	Mid Speed: K (Front)	[300 to 1000 / 690 / 1-V/step]
042	Mid Speed: C (Front)	[300 to 1000 / 690 / 1-V/step]
043	Mid Speed: M (Front)	[300 to 1000 / 690 / 1-V/step]
044	Mid Speed: Y (Front)	[300 to 1000 / 690 / 1-V/step]
051	Low Speed: K (Front)	[300 to 1000 / 690 / 1-V/step]
052	Low Speed: C (Front)	[300 to 1000 / 690 / 1-V/step]
053	Low Speed: M (Front)	[300 to 1000 / 690 / 1-V/step]
054	Low Speed: Y (Front)	[300 to 1000 / 690 / 1-V/step]
061	Std Speed: K (Center)	[300 to 1000 / 690 / 1-V/step]
062	Std Speed: C (Center)	[300 to 1000 / 690 / 1-V/step]
063	Std Speed: M (Center)	[300 to 1000 / 690 / 1-V/step]
064	Std Speed: Y (Center)	[300 to 1000 / 690 / 1-V/step]
071	Mid Speed: K (Center)	[300 to 1000 / 690 / 1-V/step]
072	Mid Speed: C (Center)	[300 to 1000 / 690 / 1-V/step]
073	Mid Speed: M (Center)	[300 to 1000 / 690 / 1-V/step]
074	Mid Speed: Y (Center)	[300 to 1000 / 690 / 1-V/step]
081	Low Speed: K (Center)	[300 to 1000 / 690 / 1-V/step]
082	Low Speed: C (Center)	[300 to 1000 / 690 / 1-V/step]
083	Low Speed: M (Center)	[300 to 1000 / 690 / 1-V/step]
084	Low Speed: Y (Center)	[300 to 1000 / 690 / 1-V/step]
091	Std Speed: K (Rear)	[300 to 1000 / 690 / 1-V/step]
092	Std Speed: C (Rear)	[300 to 1000 / 690 / 1-V/step]
093	Std Speed: M (Rear)	[300 to 1000 / 690 / 1-V/step]

Main SP Tables-3

094	Std Speed: Y (Rear)		[300 to 1000 / 690 / 1-V/step]
101	Mid Speed: K (Rear)		[300 to 1000 / 690 / 1-V/step]
102	Mid Speed: C (Rear)		[300 to 1000 / 690 / 1-V/step]
103	Mid Speed: M (Rear)		[300 to 1000 / 690 / 1-V/step]
104	Mid Speed: Y (Rear)		[300 to 1000 / 690 / 1-V/step]
111	Low Speed: K (Rear)		[300 to 1000 / 690 / 1-V/step]
112	Low Speed: C (Rear)		[300 to 1000 / 690 / 1-V/step]
113	Low Speed: M (Rear)		[300 to 1000 / 690 / 1-V/step]
114	Low Speed: Y (Rear)		[300 to 1000 / 690 / 1-V/step]
201	Now:Std Speed: K	ENG	[300 to 1000 / 690 / 1-V/step]
202	Now:Std Speed: C	ENG	[300 to 1000 / 690 / 1-V/step]
203	Now:Std Speed: M	ENG	[300 to 1000 / 690 / 1-V/step]
204	Now:Std Speed: Y	ENG	[300 to 1000 / 690 / 1-V/step]
3611	[Chrg DC Control]
3611	Electrify bias to actually set including value corrected with RTP.
211	Now:Mid Speed: K	ENG	[300 to 1000 / 690 / 1-V/step]
212	Now:Mid Speed: C	ENG	[300 to 1000 / 690 / 1-V/step]
213	Now:Mid Speed: M	ENG	[300 to 1000 / 690 / 1-V/step]
214	Now:Mid Speed: Y	ENG	[300 to 1000 / 690 / 1-V/step]
221	Now:Low Speed: K	ENG	[300 to 1000 / 690 / 1-V/step]
222	Now:Low Speed: C	ENG	[300 to 1000 / 690 / 1-V/step]
223	Now:Low Speed: M	ENG	[300 to 1000 / 690 / 1-V/step]
224	Now:Low Speed: Y	ENG	[300 to 1000 / 690 / 1-V/step]

SP Mode Tables

Main SP Tables-3

3612	[Dev DC Control]
3612	Displays develop bias decided with Pro-Con.
001	Std Speed: K	*ENG	[200 to 800 / 550 / 1-V/step]
002	Std Speed: C	*ENG	[200 to 800 / 550 / 1-V/step]
003	Std Speed: M	*ENG	[200 to 800 / 550 / 1-V/step]
004	Std Speed: Y	*ENG	[200 to 800 / 550 / 1-V/step]
011	Mid Speed: K	*ENG	[200 to 800 / 550 / 1-V/step]
012	Mid Speed: C	*ENG	[200 to 800 / 550 / 1-V/step]
013	Mid Speed: M	*ENG	[200 to 800 / 550 / 1-V/step]
014	Mid Speed: Y	*ENG	[200 to 800 / 550 / 1-V/step]
021	Low Speed: K	*ENG	[200 to 800 / 550 / 1-V/step]
022	Low Speed: C	*ENG	[200 to 800 / 550 / 1-V/step]
023	Low Speed: M	*ENG	[200 to 800 / 550 / 1-V/step]
024	Low Speed: Y	*ENG	[200 to 800 / 550 / 1-V/step]
031	Std Speed: K (Front)		[200 to 800 / 550 / 1-V/step]
032	Std Speed: C (Front)		[200 to 800 / 550 / 1-V/step]
033	Std Speed: M (Front)		[200 to 800 / 550 / 1-V/step]
034	Std Speed: Y (Front)		[200 to 800 / 550 / 1-V/step]
041	Mid Speed: K (Front)		[200 to 800 / 550 / 1-V/step]
042	Mid Speed: C (Front)		[200 to 800 / 550 / 1-V/step]
043	Mid Speed: M (Front)		[200 to 800 / 550 / 1-V/step]
044	Mid Speed: Y (Front)		[200 to 800 / 550 / 1-V/step]
051	Low Speed: K (Front)		[200 to 800 / 550 / 1-V/step]
052	Low Speed: C (Front)		[200 to 800 / 550 / 1-V/step]
053	Low Speed: M (Front)		[200 to 800 / 550 / 1-V/step]

Main SP Tables-3

054	Low Speed: Y (Front)	[200 to 800 / 550 / 1-V/step]
061	Std Speed: K (Center)	[200 to 800 / 550 / 1-V/step]
062	Std Speed: C (Center)	[200 to 800 / 550 / 1-V/step]
063	Std Speed: M (Center)	[200 to 800 / 550 / 1-V/step]
064	Std Speed: Y (Center)	[200 to 800 / 550 / 1-V/step]
071	Mid Speed: K (Center)	[200 to 800 / 550 / 1-V/step]
072	Mid Speed: C (Center)	[200 to 800 / 550 / 1-V/step]
073	Mid Speed: M (Center)	[200 to 800 / 550 / 1-V/step]
074	Mid Speed: Y (Center)	[200 to 800 / 550 / 1-V/step]
081	Low Speed: K (Center)	[200 to 800 / 550 / 1-V/step]
082	Low Speed: C (Center)	[200 to 800 / 550 / 1-V/step]
083	Low Speed: M (Center)	[200 to 800 / 550 / 1-V/step]
084	Low Speed: Y (Center)	[200 to 800 / 550 / 1-V/step]
091	Std Speed: K (Rear)	[200 to 800 / 550 / 1-V/step]
092	Std Speed: C (Rear)	[200 to 800 / 550 / 1-V/step]
093	Std Speed: M (Rear)	[200 to 800 / 550 / 1-V/step]
094	Std Speed: Y (Rear)	[200 to 800 / 550 / 1-V/step]
101	Mid Speed: K (Rear)	[200 to 800 / 550 / 1-V/step]
102	Mid Speed: C (Rear)	[200 to 800 / 550 / 1-V/step]
103	Mid Speed: M (Rear)	[200 to 800 / 550 / 1-V/step]
104	Mid Speed: Y (Rear)	[200 to 800 / 550 / 1-V/step]
111	Low Speed: K (Rear)	[200 to 800 / 550 / 1-V/step]
112	Low Speed: C (Rear)	[200 to 800 / 550 / 1-V/step]
113	Low Speed: M (Rear)	[200 to 800 / 550 / 1-V/step]
114	Low Speed: Y (Rear)	[200 to 800 / 550 / 1-V/step]

SP Mode Tables

Main SP Tables-3

3612	[Dev DC Control]
120	Set:Vb Limit	*ENG	[0 to 500 / 50 / 1V/step]
120	Controls bias variable amount when Pro-Con interrupting.
3612	[Dev DC Control]
3612	Sets upper limit develop Vb.
121	Set:Limit TC1	*ENG	[1.0 to 15.0 / 6.5 / 0.1wt%/step]
122	Set:Limit TC2	*ENG	[1.0 to 15.0 / 7.0 / 0.1wt%/step]
123	Set:Page Thresh	*ENG	[0 to 999999 / 35000 / 1page/step]
131	Set:Upper Vb Current:K	*ENG	[0 to 800 / 600 / 1V/step]
132	Set:Upper Vb Current:C	*ENG
133	Set:Upper Vb Current:M	*ENG
134	Set:Upper Vb Current:Y	*ENG
3612	[Dev DC Control]
3612	Develop bias to actually set including value corrected with RTP.
201	Now:Std Speed: K	ENG	[200 to 800 / 690 / 1-V/step]
202	Now:Std Speed: C	ENG	[200 to 800 / 690 / 1-V/step]
203	Now:Std Speed: M	ENG	[200 to 800 / 690 / 1-V/step]
204	Now:Std Speed: Y	ENG	[200 to 800 / 690 / 1-V/step]
211	Now:Mid Speed: K	ENG	[200 to 800 / 690 / 1-V/step]
212	Now:Mid Speed: C	ENG	[200 to 800 / 690 / 1-V/step]
213	Now:Mid Speed: M	ENG	[200 to 800 / 690 / 1-V/step]
214	Now:Mid Speed: Y	ENG	[200 to 800 / 690 / 1-V/step]
221	Now:Low Speed: K	ENG	[200 to 800 / 690 / 1-V/step]
222	Now:Low Speed: C	ENG	[200 to 800 / 690 / 1-V/step]
223	Now:Low Speed: M	ENG	[200 to 800 / 690 / 1-V/step]

Main SP Tables-3

224

Now:Low Speed: Y

ENG

[200 to 800 / 690 / 1-V/step]

3613	[LD Power Control]
3613	Displays LD power decided with Pro-Con.
001	Std Speed: K	*ENG	[0 to 200 / 100 / 1%/step]
002	Std Speed: C		[0 to 200 / 100 / 1%/step]
003	Std Speed: M		[0 to 200 / 100 / 1%/step]
004	Std Speed: Y		[0 to 200 / 100 / 1%/step]
011	Mid Speed: K		[0 to 200 / 100 / 1%/step]
012	Mid Speed: C		[0 to 200 / 100 / 1%/step]
013	Mid Speed: M		[0 to 200 / 100 / 1%/step]
014	Mid Speed: Y		[0 to 200 / 100 / 1%/step]
021	Std Speed: K		[0 to 200 / 100 / 1%/step]
022	Std Speed: C		[0 to 200 / 100 / 1%/step]
023	Std Speed: M		[0 to 200 / 100 / 1%/step]
024	Std Speed: Y		[0 to 200 / 100 / 1%/step]
031	Std Speed: K (Front)		[0 to 200 / 100 / 1%/step]
032	Std Speed: C (Front)		[0 to 200 / 100 / 1%/step]
033	Std Speed: M (Front)		[0 to 200 / 100 / 1%/step]
034	Std Speed: Y (Front)		[0 to 200 / 100 / 1%/step]
041	Mid Speed: K (Front)		[0 to 200 / 100 / 1%/step]
042	Mid Speed: C (Front)		[0 to 200 / 100 / 1%/step]
043	Mid Speed: M (Front)		[0 to 200 / 100 / 1%/step]
044	Mid Speed: Y (Front)		[0 to 200 / 100 / 1%/step]
051	Low Speed: K (Front)		[0 to 200 / 100 / 1%/step]
052	Low Speed: C (Front)		[0 to 200 / 100 / 1%/step]

SP Mode Tables

Main SP Tables-3

053	Low Speed: M (Front)		[0 to 200 / 100 / 1%/step]
054	Low Speed: Y (Front)		[0 to 200 / 100 / 1%/step]
061	Std Speed: K (Center)		[0 to 200 / 100 / 1%/step]
062	Std Speed: C (Center)		[0 to 200 / 100 / 1%/step]
063	Std Speed: M (Center)		[0 to 200 / 100 / 1%/step]
064	Std Speed: Y (Center)		[0 to 200 / 100 / 1%/step]
071	Mid Speed: K (Center)		[0 to 200 / 100 / 1%/step]
072	Mid Speed: C (Center)		[0 to 200 / 100 / 1%/step]
073	Mid Speed: M (Center)		[0 to 200 / 100 / 1%/step]
074	Mid Speed: Y (Center)		[0 to 200 / 100 / 1%/step]
081	Low Speed: K (Center)		[0 to 200 / 100 / 1%/step]
082	Low Speed: C (Center)		[0 to 200 / 100 / 1%/step]
083	Low Speed: M (Center)		[0 to 200 / 100 / 1%/step]
084	Low Speed: Y (Center)		[0 to 200 / 100 / 1%/step]
091	Std Speed: K (Rear)		[0 to 200 / 100 / 1%/step]
092	Std Speed: C (Rear)		[0 to 200 / 100 / 1%/step]
093	Std Speed: M (Rear)		[0 to 200 / 100 / 1%/step]
094	Std Speed: Y (Rear)		[0 to 200 / 100 / 1%/step]
3613	[LD Power Control]
3613	LD Power of Pro-Con pattern part.
101	PrcsCntrlCorrect:K	ENG	[0 to 200 / 140 / 1%/step]
102	PrcsCntrlCorrect:C	ENG	[0 to 200 / 140 / 1%/step]
103	PrcsCntrlCorrect:M	ENG	[0 to 200 / 140 / 1%/step]
104	PrcsCntrlCorrect:Y	ENG	[0 to 200 / 140 / 1%/step]
111	Low Speed: K (Rear)		[0 to 200 / 140 / 1%/step]
112	Low Speed: C (Rear)		[0 to 200 / 140 / 1%/step]

Main SP Tables-3

113	Low Speed: M (Rear)		[0 to 200 / 140 / 1%/step]
114	Low Speed: Y (Rear)		[0 to 200 / 140 / 1%/step]
121	Mid Speed: K (Rear)		[0 to 200 / 140 / 1%/step]
122	Mid Speed: C (Rear)		[0 to 200 / 140 / 1%/step]
123	Mid Speed: M (Rear)		[0 to 200 / 140 / 1%/step]
124	Mid Speed: Y (Rear)		[0 to 200 / 140 / 1%/step]
3613	[LD Power Control]
3613	Ld Power to actually set including value corrected with RTP.
201	Now:Std Speed: K	ENG	[0 to 200 / 100 / 1%/step]
202	Now:Std Speed: C	ENG	[0 to 200 / 100 / 1%/step]
203	Now:Std Speed: M	ENG	[0 to 200 / 100 / 1%/step]
204	Now:Std Speed: Y	ENG	[0 to 200 / 100 / 1%/step]
211	Now:Mid Speed: K	ENG	[0 to 200 / 100 / 1%/step]
212	Now:Mid Speed: C	ENG	[0 to 200 / 100 / 1%/step]
213	Now:Mid Speed: M	ENG	[0 to 200 / 100 / 1%/step]
214	Now:Mid Speed: Y	ENG	[0 to 200 / 100 / 1%/step]
221	Now:Low Speed: K	ENG	[0 to 200 / 100 / 1%/step]
222	Now:Low Speed: C	ENG	[0 to 200 / 100 / 1%/step]
223	Now:Low Speed: M	ENG	[0 to 200 / 100 / 1%/step]
224	Now:Low Speed: Y	ENG	[0 to 200 / 100 / 1%/step]

3619	[Bias:Spd Corr]
3619	Sets correction conditions per line speed of develop bias.
001	VbCoef:Std Spd: K	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
002	VbCoef:Std Spd: C	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
003	VbCoef:Std Spd: M	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]

SP Mode Tables

Main SP Tables-3

004	VbCoef:Std Spd: Y	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
011	VbCoef:Mid Spd: K	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
012	VbCoef:Mid Spd: C	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
013	VbCoef:Mid Spd: M	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
014	VbCoef:Mid Spd: Y	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
021	VbCoef:Low Spd: K	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
022	VbCoef:Low Spd: C	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
023	VbCoef:Low Spd: M	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
024	VbCoef:Low Spd: Y	*ENG	[0.50 to 1.50 / 1.00 / 0.01/step]
051	Offset: Std Spd: K	*ENG	[-128 to 127 / 39 / 1V/step]
052	Offset: Std Spd: C	*ENG	[-128 to 127 / 39 / 1V/step]
053	Offset: Std Spd: M	*ENG	[-128 to 127 / 39 / 1V/step]
054	Offset: Std Spd: Y	*ENG	[-128 to 127 / 39 / 1V/step]
061	Offset: Mid Spd: K	*ENG	[-128 to 127 / 39 / 1V/step]
062	Offset: Mid Spd: C	*ENG	[-128 to 127 / 39 / 1V/step]
063	Offset: Mid Spd: M	*ENG	[-128 to 127 / 39 / 1V/step]
064	Offset: Mid Spd: Y	*ENG	[-128 to 127 / 39 / 1V/step]
071	Offset: Low Spd: K	*ENG	[-128 to 127 / 39 / 1V/step]
072	Offset: Low Spd: C	*ENG	[-128 to 127 / 39 / 1V/step]
073	Offset: Low Spd: M	*ENG	[-128 to 127 / 39 / 1V/step]
074	Offset: Low Spd: Y	*ENG	[-128 to 127 / 39 / 1V/step]

3620

[ProCon Target M/A]

001

Maximum M/A:K

*ENG

[0.250 to 0.750 / 0.370 /

0.001mg/cm2/step]

Sets solid deposit (K).

Main SP Tables-3

002

Maximum M/A:C

*ENG

[0.250 to 0.750 / 0.400 /

0.001mg/cm2/step]

Sets solid deposit (C).

003

Maximum M/A:M

*ENG

[0.250 to 0.750 / 0.450 /

0.001mg/cm2/step]

Sets solid deposit (M).

004

Maximum M/A:Y

*ENG

[0.250 to 0.750 / 0.400 /

0.001mg/cm2/step]

Sets solid deposit (Y).

3621	[Backgroud Pot:Set]
3621	 Sets background potential  Default: 100V, carrier deposit will occur when setting value too high.
001	Slope:K	*ENG	[-1000 to 1000 / 0 / 1/step]
002	Slope:C	*ENG
003	Slope:M	*ENG
004	Slope:Y	*ENG
011	intercept:K	*ENG	[0 to 255 / 120 / 1V/step]
012	intercept:C	*ENG
013	intercept:M	*ENG
014	intercept:Y	*ENG
3621	[Backgroud Pot:Set]
3621	Sets background potential. (Upper/lower limit).
051	UpperLimit	*ENG	[100 to 1000 / 150 / 1V/step]
052	LowerLimit	*ENG	[0 to 100 / 100 / 1V/step]

3622	[Dev Pot :Set]
001	Current:K	*ENG	[0 to 800 / 0 / 1V/step]

SP Mode Tables

Main SP Tables-3

	Displays Development Potential: Current Value (K).
002	Current:C	*ENG	[0 to 800 / 0 / 1V/step]
	Displays Development Potential: Current Value (C).
003	Current:M	*ENG	[0 to 800 / 0 / 1V/step]
	Displays Development Potential: Current Value (M).
004	Current:Y	*ENG	[0 to 800 / 0 / 1V/step]
	Displays Development Potential: Current Value (Y).
011	Current:F_K	*ENG	[0 to 800 / 0 / 1V/step]
	Displays Development Potential: Target Value (K).
012	Current:F_C	*ENG	[0 to 800 / 0 / 1V/step]
	Displays Development Potential: Target Value (C).
013	Current:F_M	*ENG	[0 to 800 / 0 / 1V/step]
	Displays Development Potential: Target Value (M).
014	Current:F_Y	*ENG	[0 to 800 / 0 / 1V/step]
	Displays Development Potential: Target Value (Y).
021	Current:C_K	ENG	[0 to 800 / 0 / 1V/step]
	Displays develop potential (K).
022	Current:C_C	ENG	[0 to 800 / 0 / 1V/step]
	Displays develop potential (C).
023	Current:C_M	ENG	[0 to 800 / 0 / 1V/step]
	Displays develop potential (M).
024	Current:C_Y	ENG	[0 to 800 / 0 / 1V/step]
	Displays develop potential (Y).
031	Current:R_K	ENG	[0 to 800 / 0 / 1V/step]
	Displays develop potential (K).
032	Current:R_C	ENG	[0 to 800 / 0 / 1V/step]

Main SP Tables-3

	Displays develop potential (C).
033	Current:R_M	ENG	[0 to 800 / 0 / 1V/step]
	Displays develop potential (M).
034	Current:R_Y	ENG	[0 to 800 / 0 / 1V/step]
	Displays develop potential (Y).
051	UpperLimit	*ENG	[400 to 800 / 700 / 1V/step]
	Sets Development Potential (Upper Limit) (K).
052	UpperLimit	*ENG	[400 to 800 / 700 / 1V/step]
	Sets Development Potential (Upper Limit) (C).
053	UpperLimit	*ENG	[400 to 800 / 700 / 1V/step]
	Sets Development Potential (Upper Limit) (M).
054	UpperLimit	*ENG	[400 to 800 / 700 / 1V/step]
	Sets Development Potential (Upper Limit) (Y).
061	LowerLimit	*ENG	[0 to 400 / 200 / 1V/step]
	Sets Development Potential (Lower Limit) (K).
062	LowerLimit	*ENG	[0 to 400 / 200 / 1V/step]
	Sets Development Potential (Lower Limit) (C).
063	LowerLimit	*ENG	[0 to 400 / 200 / 1V/step]
	Sets Development Potential (Lower Limit) (M).
064	LowerLimit	*ENG	[0 to 400 / 200 / 1V/step]
	Sets Development Potential (Lower Limit) (Y).
101	Target:K	*ENG	[0 to 800 / 0 / 1V/step]
	Displays Development Potential: Current Value (K) according to paper.
102	Target:C	*ENG	[0 to 800 / 0 / 1V/step]
	Displays Development Potential: Current Value (C) according to paper.
103	Target:M	*ENG	[0 to 800 / 0 / 1V/step]

SP Mode Tables

Main SP Tables-3

	Displays Development Potential: Current Value (M) according to paper.
104	Target:Y	*ENG	[0 to 800 / 0 / 1V/step]
	Displays Development Potential: Current Value (Y) according to paper.
111	Target Corr:K	*ENG	[-128 to 127 / 0 / 1/step]
	Displays develop potential target value correction amount (K).
112	Target Corr:C	*ENG	[-128 to 127 / 0 / 1/step]
	Displays develop potential target value correction amount (C).
113	Target Corr:M	*ENG	[-128 to 127 / 0 / 1/step]
	Displays develop potential target value correction amount (M).
114	Target Corr:Y	*ENG	[-128 to 127 / 0 / 1/step]
	Displays develop potential target value correction amount (Y).
121	Vk:Upper_K	*ENG	[0 to 255 / 30 / 1-V/step]
	Regulates upper limit of start developing voltage value (K).
122	Vk:Upper_Col	*ENG	[0 to 255 / 30 / 1-V/step]
	Regulates upper limit of start developing voltage value (Col).
123	Vk:Lower_K	*ENG	[-128 to 0 / -90 / 1-V/step]
	Regulates lower limit of start developing voltage value (K).
124	Vk:Lower_Col	*ENG	[-128 to 0 / -60 / 1-V/step]
	Regulates lower limit of start developing voltage value (Col).

3623	[LD Power :Set]
	Sets background potential  Default: 100V  Carrier deposit will occur when setting value too high.
001	Std Speed Slope:K	*ENG	[-1000 to 1000 / D146, D147: 213, D148: 221, D149, D150: 233 / 1/step]
002	Std Speed Slope:C	*ENG
003	Std Speed Slope:M	*ENG

Main SP Tables-3

004	Std Speed Slope:Y	*ENG
011	Std Speed intercept:K	*ENG	[-1000 to 1000 / -18 / 1/step]
012	Std Speed intercept:C	*ENG
013	Std Speed intercept:M	*ENG
014	Std Speed intercept:Y	*ENG
021	Mid Speed Slope:K	*ENG	[-1000 to 1000 / 213 / 1/step]
022	Mid Speed Slope:C	*ENG
023	Mid Speed Slope:M	*ENG
024	Mid Speed Slope:Y	*ENG
031	Mid Speed intercept:K	*ENG	[-1000 to 1000 / -15 / 1/step]
032	Mid Speed intercept:C	*ENG
033	Mid Speed intercept:M	*ENG
034	Mid Speed intercept:Y	*ENG
041	Low Speed Slope:K	*ENG	[-1000 to 1000 / 204 / 1/step]
042	Low Speed Slope:C	*ENG
043	Low Speed Slope:M	*ENG
044	Low Speed Slope:Y	*ENG
051	Low Speed intercept:K	*ENG	[-1000 to 1000 / -15 / 1/step]
052	Low Speed intercept:C	*ENG
053	Low Speed intercept:M	*ENG
054	Low Speed intercept:Y	*ENG

3624

[TC Adj. Mode]

001

Target(Upp Limit)

*ENG

[0.00 to 1.00 / 0.15 / 0.01

mg/cm2/-kV/step]

Sets Development gamma Adjustment Target (Upp Limit) for Toner Density Adjustment.

SP Mode Tables

Main SP Tables-3

002	Target(Lwr Limit)	*ENG	[-1 to 0.00 / -0.15 / 0.01 mg/cm2/-kV/step]
	Sets Development gamma Adjustment Target (Lwr Limit) for Toner Density Adjustment.
005	Force Consume Threshold	*ENG	[1.00 to 6.00 / 1.50 / 0.01 mg/cm2/-kV/step]
	Sets Force Consume Threshold for Density Adjustment.
006	Consume(Upp Limit)	*ENG	[10 to 2550 / 294 / 1cm^2]
	Sets Consume (Upp Limit) for Density Adjustment.
007	Consume(Upp Limit)	*ENG	[0 to 255 / 20 / 1times/step]
	Sets Consume (Upp Limit) for Density Adjustment.
008	Force Supply Threshold	*ENG	[0.00 to 1.00 / 0.50 / 0.01 mg/cm2/-kV/step]
	Sets Force Consume Threshold for Density Adjustment.
009	Supply(Upp Limit)	*ENG	[0.0 to 50.0 / 3.0 / 0.1g/step]
	Sets Supply (Upp Limit) for Density Adjustment.
010	Supply(Lwr Limit)	*ENG	[0.0 to 50.0 / 1.0 / 0.1g/step]
	Sets Supply (Lwr Limit) for Density Adjustment.
021	Consumption Pat: DUTY: K	*ENG	[0 to 15 / 15 / 1/step]
022	Consumption Pat: DUTY: C	*ENG
023	Consumption Pat: DUTY: M	*ENG
024	Consumption Pat: DUTY: Y	*ENG
3624	[TC Adj. Mode]
031	Max Counts:PowerON	*ENG	[0 to 50 / 0 / 1/step]
	Sets consume counts (upper limit) for toner density adjusting Pro-Con.
3624	[TC Adj. Mode]
	Sets adjust counts for toner density adjusting Pro-Con.

Main SP Tables-3

033	Max Counts:Printing	*ENG	[0 to 50 / 0 / 1/step]
034	Max Counts:Job End	*ENG	[0 to 50 / 0 / 1/step]
035	Max Counts:ACC	*ENG	[0 to 50 / 3 / 1/step]
036	Max Counts:Initial Setting	*ENG
037	Max Counts:Replenishment	*ENG
038	Max Counts:Recovery	*ENG
3624	[TC Adj. Mode]
3624	Sets execute threshold for density adjust Pro-Con against absolute humidity.
071	AbsHumThresh(Upp)	*ENG	[0.00 to 100.00 / 16.00 / 0.01g/m3/step]
072	AbsHumThresh(Low)	*ENG	[0.00 to 100.00 / 4.00 / 0.01g/m3/step]
073	AbsHumThresh(Range)	*ENG	[0.00 to 100.00 / 12.00 / 0.01g/m3/step]

3627

[P Pattern Extraction :Set]

Sets edge detect threshold for ID sensor.

001

Edge Detection Threshold :K

*ENG

[0.0 to 5.0 / 2.5 / 0.1V/step]

002

Edge Detection Threshold :C

*ENG

003

Edge Detection Threshold :M

*ENG

004

Edge Detection Threshold :Y

*ENG

011

Edge Upper Limit:Potential Control

*ENG

[7.0 to 10.0 / 9.0 / 0.1mm/step]

Sets upper limit value of edge interval sampling count of P pattern by electric potential control.

(Processes an error when exceeding upper limit)

SP Mode Tables

Main SP Tables-3

012	Edge Upper Limit:IBACC	*ENG	[10.0 to 13.0 / 12.0 / 0.1mm/step]
	Sets upper limit value of edge interval sampling count of P pattern by IBACC. (Processes an error when exceeding upper limit)
013	Edge Upper Limit:RTP		[50 to 80 / 70 / 0.1mm/step]
021	Edge Lower Limit:Potential Control	*ENG	[4.0 to 7.0 / 5.0 / 0.1mm/step]
	Sets lower limit value of edge interval sampling count of P pattern by electric potential control. (Keeps searching when below lower limit value)
022	Edge Lower Limit:IBACC	*ENG	[7.0 to 10.0 / 8.0 / 0.1mm/step]
	Sets lower limit value of edge interval sampling count of P pattern IBACC. (Keeps searching when below lower limit value)
023	Edge Lower Limit:RTP	*ENG	[2.0 to 5.0 / 3.0 / 0.1mm/step]
	Sets lower limit value of edge interval sampling count of P pattern RTP. (Keeps searching when below lower limit value)

3628	[ID Pattern Timing :Set]
001	Scan: YCMK	*ENG	[-500.0 to 500.0 / 0.0 / 0.1mm/step]
	Adjusts timing of Pro-Con pattern detect by P sensor.
002	Detection Delay Time	*ENG	[0 to 2500 / 0 / 1msec/step]
	Adjusts alienation start timing of paper transfer.
003	Delay Time	*ENG	[0 to 2500 / 778 / 1msec/step]
	Adjusts start write timing of P pattern.
004	MUSIC Delay Time	*ENG	[0 to 2500 / 150 / 1msec/step]
	Adjusts start write timing of MUSIC.

Main SP Tables-3

3629	[ProCon Pattern:Set]
3629	Sets imaging conditions for electric potential control pattern.
001	ChargeDC: Pattern1: Bk	*ENG	[0 to 999 / 170 / 1V/step]
002	ChargeDC: Pattern2: Bk	*ENG	[0 to 999 / 210 / 1V/step]
003	ChargeDC: Pattern3: Bk	*ENG	[0 to 999 / 250 / 1V/step]
004	ChargeDC: Pattern4: Bk	*ENG	[0 to 999 / 290 / 1V/step]
005	ChargeDC: Pattern5: Bk	*ENG	[0 to 999 / 330 / 1V/step]
006	ChargeDC: Pattern6: Bk	*ENG	[0 to 999 / 370 / 1V/step]
007	ChargeDC: Pattern7: Bk	*ENG	[0 to 999 / 410 / 1V/step]
008	ChargeDC: Pattern8: Bk	*ENG	[0 to 999 / 450 / 1V/step]
009	ChargeDC: Pattern9: Bk	*ENG	[0 to 999 / 490 / 1V/step]
010	ChargeDC: Pattern10: Bk	*ENG	[0 to 999 / 530 / 1V/step]
011	ChargeDC: Pattern1: C	*ENG	[0 to 999 / 170 / 1V/step]
012	ChargeDC: Pattern2: C	*ENG	[0 to 999 / 230 / 1V/step]
013	ChargeDC: Pattern3: C	*ENG	[0 to 999 / 290 / 1V/step]
014	ChargeDC: Pattern4: C	*ENG	[0 to 999 / 350 / 1V/step]
015	ChargeDC: Pattern5: C	*ENG	[0 to 999 / 410 / 1V/step]
016	ChargeDC: Pattern6: C	*ENG	[0 to 999 / 470 / 1V/step]
017	ChargeDC: Pattern7: C	*ENG	[0 to 999 / 530 / 1V/step]
018	ChargeDC: Pattern8: C	*ENG	[0 to 999 / 590 / 1V/step]
019	ChargeDC: Pattern9: C	*ENG	[0 to 999 / 650 / 1V/step]
020	ChargeDC: Pattern10: C	*ENG	[0 to 999 / 710 / 1V/step]
021	ChargeDC: Pattern1: M	*ENG	[0 to 999 / 170 / 1V/step]
022	ChargeDC: Pattern2: M	*ENG	[0 to 999 / 230 / 1V/step]
023	ChargeDC: Pattern3: M	*ENG	[0 to 999 / 290 / 1V/step]

SP Mode Tables

Main SP Tables-3

024	ChargeDC: Pattern4: M	*ENG	[0 to 999 / 350 / 1V/step]
025	ChargeDC: Pattern5: M	*ENG	[0 to 999 / 410 / 1V/step]
026	ChargeDC: Pattern6: M	*ENG	[0 to 999 / 470 / 1V/step]
027	ChargeDC: Pattern7: M	*ENG	[0 to 999 / 530 / 1V/step]
028	ChargeDC: Pattern8: M	*ENG	[0 to 999 / 590 / 1V/step]
029	ChargeDC: Pattern9: M	*ENG	[0 to 999 / 650 / 1V/step]
030	ChargeDC: Pattern10: M	*ENG	[0 to 999 / 710 / 1V/step]
031	ChargeDC: Pattern1: Y	*ENG	[0 to 999 / 170 / 1V/step]
032	ChargeDC: Pattern2: Y	*ENG	[0 to 999 / 230 / 1V/step]
033	ChargeDC: Pattern3: Y	*ENG	[0 to 999 / 290 / 1V/step]
034	ChargeDC: Pattern4: Y	*ENG	[0 to 999 / 350 / 1V/step]
035	ChargeDC: Pattern5: Y	*ENG	[0 to 999 / 410 / 1V/step]
036	ChargeDC: Pattern6: Y	*ENG	[0 to 999 / 470 / 1V/step]
037	ChargeDC: Pattern7: Y	*ENG	[0 to 999 / 530 / 1V/step]
038	ChargeDC: Pattern8: Y	*ENG	[0 to 999 / 590 / 1V/step]
039	ChargeDC: Pattern9: Y	*ENG	[0 to 999 / 650 / 1V/step]
040	ChargeDC: Pattern10: Y	*ENG	[0 to 999 / 710 / 1V/step]
101	DevelopmentDC: Pattern1: Bk	*ENG	[0 to 999 / 50 / 1V/step]
102	DevelopmentDC: Pattern2: Bk	*ENG	[0 to 999 / 90 / 1V/step]
103	DevelopmentDC: Pattern3: Bk	*ENG	[0 to 999 / 130 / 1V/step]
104	DevelopmentDC: Pattern4: Bk	*ENG	[0 to 999 / 170 / 1V/step]
105	DevelopmentDC: Pattern5: Bk	*ENG	[0 to 999 / 210 / 1V/step]
106	DevelopmentDC: Pattern6: Bk	*ENG	[0 to 999 / 250 / 1V/step]
107	DevelopmentDC: Pattern7: Bk	*ENG	[0 to 999 / 290 / 1V/step]
108	DevelopmentDC: Pattern8: Bk	*ENG	[0 to 999 / 330 / 1V/step]
109	DevelopmentDC: Pattern9: Bk	*ENG	[0 to 999 / 370 / 1V/step]

Main SP Tables-3

110	DevelopmentDC: Pattern10: Bk	*ENG	[0 to 999 / 410 / 1V/step]
111	DevelopmentDC: Pattern1: C	*ENG	[0 to 999 / 50 / 1V/step]
112	DevelopmentDC: Pattern2: C	*ENG	[0 to 999 / 110 / 1V/step]
113	DevelopmentDC: Pattern3: C	*ENG	[0 to 999 / 170 / 1V/step]
123	DevelopmentDC: Pattern3: M	*ENG	[0 to 999 / 170 / 1V/step]
124	DevelopmentDC: Pattern4: M	*ENG	[0 to 999 / 230 / 1V/step]
125	DevelopmentDC: Pattern5: M	*ENG	[0 to 999 / 290 / 1V/step]
133	DevelopmentDC: Pattern3: Y	*ENG	[0 to 999 / 170 / 1V/step]
134	DevelopmentDC: Pattern4: Y	*ENG	[0 to 999 / 230 / 1V/step]
135	DevelopmentDC: Pattern5: Y	*ENG	[0 to 999 / 290 / 1V/step]
136	DevelopmentDC: Pattern6: Y	*ENG	[0 to 999 / 350 / 1V/step]
137	DevelopmentDC: Pattern7: Y	*ENG	[0 to 999 / 410 / 1V/step]
138	DevelopmentDC: Pattern8: Y	*ENG	[0 to 999 / 470 / 1V/step]
139	DevelopmentDC: Pattern9: Y	*ENG	[0 to 999 / 530 / 1V/step]
140	DevelopmentDC: Pattern10: Y	*ENG	[0 to 999 / 590 / 1V/step]

3630

[Dev gamma :Disp/Set]

001

Current:K

*ENG

[0.10 to 6.00 / 0.95 / 0.01

mg/cm2/-kV/step]

Displays the latest Development gamma (K).

002

Current:C

*ENG

[0.10 to 6.00 / 0.95 / 0.01

mg/cm2/-kV/step]

Displays the latest Development gamma (C).

003

Current:M

*ENG

[0.10 to 6.00 / 1.05 / 0.01

mg/cm2/-kV/step]

Displays the latest Development gamma (M).

SP Mode Tables

Main SP Tables-3

004

Current:Y

*ENG

[0.10 to 6.00 / 0.95 / 0.01

mg/cm2/-kV/step]

Displays the latest Development gamma (Y).

011

Target:K

*ENG

[0.50 to 2.55 / 0.95 / 0.01

mg/cm2/-kV/step]

Displays Target Value for Development gamma (K).

Displays environment correction amount of develop gamma.

042

Environ Corr:Col

*ENG

[-1.00 to 1.00 / 0.00 / 0.01

mg/cm2/-kV/step]

Displays environment correction amount of develop gamma.

051

TnrDensity Corr:K

*ENG

[-1.00 to 1.00 / 0.00 / 0.01

mg/cm2/-kV/step]

Displays toner density correction amount of develop gamma. (K)

052

TnrDensity Corr:C

*ENG

[-1.00 to 1.00 / 0.00 / 0.01

mg/cm2/-kV/step]

Displays toner density correction amount of develop gamma. (C)

053

TnrDensity Corr:M

*ENG

[-1.00 to 1.00 / 0.00 / 0.01

mg/cm2/-kV/step]

Displays toner density correction amount of develop gamma. (M)

054

TnrDensity Corr:Y

*ENG

[-1.00 to 1.00 / 0.00 / 0.01

mg/cm2/-kV/step]

Displays toner density correction amount of develop gamma. (Y)

061

TnrDensity:K

*ENG

[0.0 to 25.5 / 0.0 / 0.1 wt%/step]

Displays Toner Density (K) converted based on TD Sensor output.

062

TnrDensity:C

*ENG

[0.0 to 25.5 / 0.0 / 0.1 wt%/step]

Displays Toner Density (C) converted based on TD Sensor output.

063

TnrDensity:M

*ENG

[0.0 to 25.5 / 0.0 / 0.1 wt%/step]

Displays Toner Density (M) converted based on TD Sensor output.

Main SP Tables-3

064

TnrDensity:Y

*ENG

[0.0 to 25.5 / 0.0 / 0.1 wt%/step]

Displays Toner Density (Y) converted based on TD Sensor output.

071

Environ Corr1:K

*ENG

[-1.00 to 1.00 / 0.00 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 1) of develop gamma.

072

Environ Corr2:K

*ENG

[-1.00 to 1.00 / 0.04 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 2) of develop gamma.

073

Environ Corr3:K

*ENG

[-1.00 to 1.00 / 0.06 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 3) of develop gamma.

074

Environ Corr4:K

*ENG

[-1.00 to 1.00 / 0.08 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 4) of develop gamma.

075

Environ Corr5:K

*ENG

[-1.00 to 1.00 / 0.10 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 5) of develop gamma.

076

Environ Corr6:K

*ENG

[-1.00 to 1.00 / 0.10 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 6) of develop gamma

081

Environ Corr1:Col

*ENG

[-1.00 to 1.00 / 0.00 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 1) of develop gamma.

SP Mode Tables

Main SP Tables-3

082

Environ Corr2:Col

*ENG

[-1.00 to 1.00 / 0.04 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 2) of develop gamma.

083

Environ Corr3:Col

*ENG

[-1.00 to 1.00 / 0.06 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 3) of develop gamma.

084

Environ Corr4:Col

*ENG

[-1.00 to 1.00 / 0.08 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 4) of develop gamma.

085

Environ Corr5:Col

*ENG

[-1.00 to 1.00 / 0.10 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 5) of develop gamma.

086

Environ Corr6:Col

*ENG

[-1.00 to 1.00 / 0.10 / 0.01

mg/cm2/-kV/step]

Sets environment correction table value (environment section 6) of develop gamma.

090

TC-Gamma

*ENG

[0.10 to 0.25 / 0.20 / 0.01/step]

Slope of TC-develop gamma.

091

TC Corr ThreshHold:K

*ENG

[7.0 to 12.0 / 9.0 / 0.1wt%/step]

Sets toner density threshold for correction using TC correction term of develop gamma (target).

092

TC Corr ThreshHold:C

*ENG

[7.0 to 12.0 / 9.0 / 0.1wt%/step]

Sets toner density threshold for correction using TC correction term of develop gamma (target).

093

TC Corr ThreshHold:M

*ENG

[7.0 to 12.0 / 9.0 / 0.1wt%/step]

Main SP Tables-3

	Sets toner density threshold for correction using TC correction term of develop gamma (target).
094	TC Corr ThreshHold:Y	*ENG	[7.0 to 12.0 / 9.0 / 0.1wt%/step]
094	Sets toner density threshold for correction using TC correction term of develop gamma (target).
3630	[Dev gamma :Disp/Set]
101	UpperLimit	*ENG	[1.00 to 5.00 / 5.00 / 0.01mg/cm2/-kV/step]
101	Displays initial value of develop gamma (K).
102	LowerLimit	*ENG	[0.10 to 1.00 / 0.15 / 0.01mg/cm2/-kV/step]
102	Displays initial value of develop gamma (C).
3630	[Dev gamma :Disp/Set]
3630	Displays latest develop gamma.
111	Current:F_K	ENG	[0.10 to 6.00 / 0.90 / 0.01mg/cm2/-kV/step]
112	Current:F_C	ENG	[0.10 to 6.00 / 0.80 / 0.01mg/cm2/-kV/step]
113	Current:F_M	ENG
114	Current:F_Y	ENG
121	Current:C_K	ENG	[0.10 to 6.00 / 0.90 / 0.01mg/cm2/-kV/step]
122	Current:C_C	ENG	[0.10 to 6.00 / 0.80 / 0.01mg/cm2/-kV/step]
123	Current:C_M	ENG
124	Current:C_Y	ENG
131	Current:R_K	ENG	[0.10 to 6.00 / 0.90 / 0.01mg/cm2/-kV/step]
132	Current:R_C	ENG	[0.10 to 6.00 / 0.80 / 0.01mg/cm2/-kV/step]
133	Current:R_M	ENG	[0.10 to 6.00 / 0.80 / 0.01mg/cm2/-kV/step]

SP Mode Tables

Main SP Tables-3

134

Current:R_Y

ENG

3630

[Dev gamma :Disp/Set]

Regulates valid deposit amount range for calculating develop gamma.

141

Range M/A Upp:K

*ENG

[0.20 to 1.00 / 0.40 /

0.01mg/cm2/step]

142

Range M/A Low:K

*ENG

[0.00 to 0.20 / 0.05 /

0.01mg/cm2/step]

143

Range M/A Upp:Col

*ENG

[0.20 to 1.00 / 0.50 /

0.01mg/cm2/step]

144

Range M/A Low:Col

*ENG

[0.00 to 0.20 / 0.05 /

0.01mg/cm2/step]

3631	[Vk :Disp]
3631	Displays latest develop start voltage.
001	Current:K	*ENG	[-300 to 300 / 0 / 1-V/step]
002	Current:C	*ENG
003	Current:M	*ENG
004	Current:Y	*ENG
111	Current:F_K	ENG	[-300 to 300 / 0 / 1-V/step]
112	Current:F_C	ENG
113	Current:F_M	ENG
114	Current:F_Y	ENG
121	Current:C_K	ENG	[-300 to 300 / 0 / 1-V/step]
122	Current:C_C	ENG
123	Current:C_M	ENG
124	Current:C_Y	ENG
131	Current:R_K	ENG	[-300 to 300 / 0 / 1-V/step]

Main SP Tables-3

132	Current:R_C	ENG
133	Current:R_M	ENG
134	Current:R_Y	ENG

3650	[APC: Set]
001	Interval	*ENG	[0 to 200 / 0 / 1page/step]
001	Sets executing interval of electric potential control during printing.
3650	[APC: Set]
3650	Sets deposit amount threshold (upper/lower limit) to start supplying with supply gain 3 of electric potential control during print.
011	Page Cnt:K	*ENG	[0 to 200 / 0 / 1pages/step]
012	Page Cnt:C		[0 to 200 / 0 / 1pages/step]
013	Page Cnt:M		[0 to 200 / 0 / 1pages/step]
014	Page Cnt:Y		[0 to 200 / 0 / 1pages/step]
021	Maximum M/A Corr:K		[-150.000 to 150.000 / 1.000 / 0.001mg/cm2/step]
022	Maximum M/A Corr:C		[-150.000 to 150.000 / 1.000 / 0.001mg/cm2/step]
023	Maximum M/A Corr:M		[-150.000 to 150.000 / 1.000 / 0.001mg/cm2/step]
024	Maximum M/A Corr:Y		[-150.000 to 150.000 / 1.000 / 0.001mg/cm2/step]
031	M/A UpperLimit2:K	*ENG	[0.000 to 0.100 / 0.020 / 0.001mg/cm2/step]
032	M/A UpperLimit2:C	*ENG	[0.000 to 0.100 / 0.020 / 0.001mg/cm2/step]
033	M/A UpperLimit2:M	*ENG
034	M/A UpperLimit2:Y	*ENG

SP Mode Tables

Main SP Tables-3

041	M/A LowerLimit2:K	*ENG	[0.000 to 0.100 / 0.020 / 0.001mg/cm2/step]
042	M/A LowerLimit2:C	*ENG	[0.000 to 0.100 / 0.020 / 0.001mg/cm2/step]
043	M/A LowerLimit2:M	*ENG
044	M/A LowerLimit2:Y	*ENG
3650	[APC: Set]
051	Corr Gain(GAMMA)	*ENG	[0 to 99 / 5 / 1/step]
	Sets correction gain 1 of electric potential control during printing.
052	Corr Gain(ASSIST)	*ENG	[0 to 99 / 4 / 1/step]
	Sets correction gain 2 of electric potential control during printing.
053	Corr Gain(ADJUST)	*ENG	[0 to 99 / 6 / 1/step]
	Sets correction gain 3 of electric potential control during printing.
054	Corr3MaxCnt	*ENG	[0 to 99 / 30 / 1time/step]
	Sets correction times for correction gain 3 of electric potential control during printing.
055	Interval Coef	*ENG	[0.0 to 1.0 / 0.5 / 0.1/step]
	Correction coefficient to correct Paper interval P pattern create interval.
056	ADJUSTMaxCnt	*ENG	[0 to 99 / 5 / 1time/step]
	Sets correction times for ASSIST of electric potential control during printing.
3650	[APC: Set]
	Sets execution flag for correction gain 3 of electric potential control during printing.
061	ADJUST Flag:K	*ENG	[0 or 1 / 0 / 1/step]
062	ADJUST Flag:C	*ENG
3650	[APC: Set]
	Displays execution times counter for correction gain 3 of electric potential control during printing.

Main SP Tables-3

071	ADJUST Exe Cnt:K	*ENG	[0 to 99 / 0 / 1pages]
072	ADJUST Exe Cnt:C	*ENG
073	ADJUST Exe Cnt:M	*ENG
074	ADJUST Exe Cnt:Y	*ENG
3650	[APC: Set]
3650	Sets delta Vt value to decide Vt threshold of electric potential during printing.
081	Vt Thresh:Range:K	*ENG	[0.00 to 1.00 / 0.20 / 0.01V/step]
082	Vt Thresh:Range:C	*ENG
083	Vt Thresh:Range:M	*ENG
084	Vt Thresh:Range:Y	*ENG
3650	[APC: Set]
101	limit:LDP	*ENG	[0 to 10 / 10 / 1%/step]
101	Upper limit threshold for LDP variable amount of APC.
102	limit:Bias	*ENG	[0 to 30 / 10 / 1V/step]
102	Upper limit threshold for bias variable amount of APC.

3660	[IBACC:Disp/Set]
3660	Density target value per IBACC pattern.
001	TargetValue:K_P1	*ENG	[0 to 1023 / 869 / 1/step]
002	TargetValue:K_P2	*ENG	[0 to 1023 / 702 / 1/step]
003	TargetValue:K_P3	*ENG	[0 to 1023 / 522 / 1/step]
004	TargetValue:K_P4	*ENG	[0 to 1023 / 323 / 1/step]
005	TargetValue:K_P5	*ENG	[0 to 1023 / 196 / 1/step]
006	TargetValue:K_P6	*ENG	[0 to 1023 / 254 / 1/step]
021	TargetValue:C_P1	*ENG	[0 to 1023 / 965 / 1/step]
022	TargetValue:C_P2	*ENG	[0 to 1023 / 909 / 1/step]

SP Mode Tables

Main SP Tables-3

023

TargetValue:C_P3

*ENG

[0 to 1023 / 832 / 1/step]

3800	[Waste Toner Full Detection]
022	Background M/A		[0 to 1000000 / 20 / 0.000001mg/mm2/step]
023	Percentage of Transfer Ratio		[0 to 1000 / 810 / 0.1%/step]
024	Date of detection for near full	*ENG	[0 or 1 / 0 / 1/step]
024	Displays latest date done mechanical detect.

3810

[Lubricant End Detection]

001

Near End Detection Distance: Thres1:Bk

*ENG

[0 to 999999999 / D146,D147:

0, D148,D149,D150: 689336 /

1cm/step]

*No use for this machine.

Rotation distance threshold: Bk from near end detect to near end detect 2.

003

End Detection Distance: Thres2:Bk

*ENG

[0 to 999999999 / 689336 /

1cm/step]

*No use for this machine.

Rotation distance threshold: Bk from near end detect to end detect.

011

Conduction Detection Times Counter:K

*ENG

[0 to 9 / 0 / 1/step]

*No use for this machine.

Accumulation of continues detecting times.

015

Near End Distance:K

*ENG

[0 to 999999999 / 0 / 1cm/step]

*No use for this machine.

PCU rotation distance of when detecting near end: saving SP

021

Detection Flag:K

*ENG

[0 to 3 / 0 / 1/step]

0: Undetected

1: mechanically detected 2: Near end detected

3: End detected.

Main SP Tables-3

*No use for this machine. Detect flag

025

New Unit Detection Flag:K

*ENG

[0 or 1 / 0 / 1/step]

0: Normal state

1: New article detected

*No use for this machine. New article detect flag

3894	[Engine Counter Clear]
001	Mainframe SP	[0 or 1 / 0 / 1/step]
002	AIT-ID chip	[0 or 1 / 0 / 1/step]
003	Toner tag	[0 or 1 / 0 / 1/step]
004	All	[0 or 1 / 0 / 1/step]

3905	[Recycled Parts: New/Old Flag]
3905	Sets a flag able to recognize whether PCU is New or recycled per machine unit. (Set to "1" for recycled)
001	OPC:K	*ENG	[0 or 1 / 0 / 1/step]
002	OPC:C	*ENG
003	OPC:M	*ENG
004	OPC:Y	*ENG

SP3-XXX (PROCESS)

HOME PAGE |

< Previous | Contents | Next >